Design for Low Power potx

... static power Design for Low PowerSlide 19 CMOS VLSI Design Low Power Design  Reduce dynamic power – α: – C: – V DD : – f:  Reduce static power Design for Low PowerSlide 5 CMOS VLSI Design Dynamic ... Low PowerSlide 2 CMOS VLSI Design Outline  Power and Energy  Dynamic Power  Static Power  Low Power Design Design for Low PowerSlide 10 CMOS...

Ngày tải lên: 01/07/2014, 11:20

... power, low rate, and wireless systems,” IEEE Transactions on Vehicular Technology, vol. 54, no. 5, pp. 1623–1631, 2005. [5] M. Verhelst and W. Dehaene, “System design of an ultra -low power, low ... group. He currently works on ultra -low- power design and wireless communication systems for body area networks. He is involved in the design of RF and analog blocks for ultra-w...

Ngày tải lên: 22/06/2014, 22:20

... Or forward body bias in active mode CMOS VLSI DesignCMOS VLSI Design 4th Ed. 7: Power 2 Outline  Power and Energy  Dynamic Power  Static Power CMOS VLSI DesignCMOS VLSI Design 4th Ed. 7: Power ... VLSI DesignCMOS VLSI Design 4th Ed. 7: Power 3 Power and Energy  Power is drawn from a voltage source attached to the V DD pin(s) of a chip.  Instantaneous Power: ...

Ngày tải lên: 19/03/2014, 10:20

... ICs for LMDS • Silicongermanium product line (gain blocks and low- noise amplifiers) • SXQ power modules for cellular and PCS applications • Power modules featuring 425-W power amplifiers for ... have therefore decided to give some guidelines for the designer applications of ICs, focusing mainly on high-performance applications. In the case of high-performance applications,...

Ngày tải lên: 31/03/2014, 22:20

... method to design allotted LDPC codes for DMT channels. The method is general and can be used for every nonuniform channel. This method allows for design of optimized LDPC codes which outperform conven- tional ... systems with nonuniform channels. This paper is organized as follows. In Section 2,webriefly review the required background of nonuniform channels and LDPC coding for unif...

Ngày tải lên: 22/06/2014, 19:20

... power [11]. The existing CBT methods are not suitable for low- power VLSI realiza- tion because of the high computation complexity and high hardware complexity. Therefore, there is a need to design ... with the Center for Signal Processing, NTU as a Research Engi- neer. His research interests include digital IC design, VLSI architec- tures for digital signal processing, low- p...

Ngày tải lên: 22/06/2014, 19:20

... the design of a MIMO WLAN transceiver. Currently he is with Alereon Inc. in Austin Texas. His technical interests include low power transceivers, frequency synthesizer design, power amplifier design. 2 ... synthesizer designs in Tab le 4. As shown, this design achieved one of the best phase noise performances for integrated WLAN transceiver RFICs. Note that in this table the pha...

Ngày tải lên: 22/06/2014, 22:20

... external circuit must be used for its estimation. Secondly, the filters are not optimized for low- power consumption which is manda- tory for the success of any battery-powered video applica- tion ... identifying, realizing, and testing a design methodology based on systolic arrays. For the past years he has been involved in the design of high-performance low- power digital s...

Ngày tải lên: 23/06/2014, 01:20

... limitation In this VGA design, the output signal is fixed to be 1V pp with 2.5V power supply, to meet the full scale of the ADC. Thus, the suitable VGA topology for this design has to provide ... suitable for low power applications. (3) Summary of analog-multiplier-based VGA In summary, the multiplier-based VGA has good linearity and large gain tuning range, but it is not...

Ngày tải lên: 06/11/2012, 10:26

Ngày tải lên: 25/12/2013, 10:38