Description:
ANDRES DISTRESSED DINING TABLE ậ PINE
Manufacturer: S. KIJCHAI CO., LTD. PO No.: 5713226
ONWARDS
Buyer: TARGET.COM Style: 242-18-1881
Country of Origin: THAILAND Country of Destination:
U.S.A.
Color: DISTRESSED PINE SKU No.: 13966663
Protocol No.: 3021-US, 9067-US UPC Code: /
Previous Report No.:
N/A ITEM#: 51011
EXECUTIVE SUMMARY:
The submitted sample is rated as PASS with satisfactory performance in the requested tests. Please refer to enclosed worksheets for the test results.
NOTES:
1. Theă sampleă wasă submittedă foră testingă underă Target.com’să standardă peră vendor’să request.
2. This Distressed Espresso wood panel style #242/18/1880 (#20111) was grouped with Distressed Pine style #242/18/1881 (#51011) for Total lead content in surface coating test.
3. The CARB documentation and CARB label were submitted for review.
4. Per Max. loading claim with 300Lbs appear on Assembly Instruction, no failure noted when a test load apply on sample with time duration of 60 minutes.
BVCPS Contact information for this report.
Technical questions:
Technical questions: (Vietnamese): Kelvin Tran, 848-37421-604 ~ 6; email: kelvin.tran@vn.bureauveritas.com Technical questions: (English): Allen Hsu, Tel: 848-37421-604 ~ 6; email: allen.hsu@vn.bureauveritas.com Concerns About Billing and General Inquiries:
Primary Contact: Christine Le, Tel: 848-37421-604 ~ 6; email: christine.le@vn.bureauveritas.com Back-up Contact: Cindy Phan, Tel: 848-37421-604 ~ 6; email: cindy.phan@vn.bureauveritas.com
BUREAU VERITAS CONSUMER PRODUCTS SERVICES (VN) LTD.
ALLEN HSU
HARDLINES DIVISION MANAGER
2.2.2.
TEST RESULT:
Total Lead Content in Surface Coating:
- United States Consumer Product Safety Improvement Act (CPSIA), Section 101(a)(2)
Test Method : CPSC-CH-E1003-09 (Issued on April 26, 2009)
Test Item(s) Item / Component Description(s) Location(s) Style(s)
I001 DISTRESSED PINE COATING WOOD SAMPLE -
I002 DISTRESSED ESPRESSO COATING WOOD COLOR
PANEL -
Maximum Allowable Limit : 90 mg/kg
- Unit Result
Test Item(s) - I001 I002
Parameter - - -
Total Lead (Pb) mg/kg ND ND
Conclusion - PASS PASS
Note / Key :
ND = Not detected ắ>Ằă=ăGreaterăthan mg/kg = milligram(s) per
kilogram
Potential Total Lead (Pb) = Estimated lead content per component is based on calculation by component individual weight
Detection Limit (mg/kg) : 10
Evaluation Citation / Method
No. of
Samples Criteria Results Rating
SCOPE:
This protocol is applicable to table intended for indoor or outdoor use.
SUPPLEMENTAL PROTOCOLS
Note: Additional cost, sample size and TAT may be required if testing to one or more supplemental protocol is necessary.
Please refer to the above referenced supplemental protocol(s) for additional information.
* California Proposition 65
TRGT-AN- PTCL-06572-
US
-
All samples shall be reviewed against the requirements of California Proposition 65 to determine if additional testing or labeling is required.
NA /
Target packaging and labeling requirements
TRGT-HL- PTCL-09067-
US
All
Products in final retail packaging or open stock shall be evaluated to the Target Packaging and Labeling Requirements Protocol
M (See Protocol
9067-US)
PASS
* Packaged product transit testing - if applicable
TRGT-HL- PTCL-09000-
US
1
All samples shall be reviewed and tested to the appropriate requirements of protocol TRGT-9000 Packaged Product Transit Testing.
Refer To Report (9612) 034-0096 /
Children's products As determined
by criteria All
All samples must be reviewed to the Target's Children's Product Definition and tested per the direction provided. If determined to be a children's product, an additional supplemental protocol will be required.
Include all applicable protocol(s) and results.
(NotăChildren’săNA Product)
/
* Toxicity supplemental
TRGT-HL- PTCL-06573-
US
-
The liquid inside a liquid filled item shall be tested to the requirements of this supplemental protocol.
NA /
* Tempered glass
CPSD-HL- PTCL-03611-
US
-
Tempered glass table tops shall be tested to the requirements of this supplemental protocol.
Exemption: The glass is permanently affixes with the substrate to its entire body.
NA
(No Glass) /
LABELING
Claim verification TRGT-HL-
08612-MTHD 1
Examine the packaging (or submitted artwork) - Report each packaging claim.
- Each claim shall be evaluated in accordance with the cited procedure.
NA /
Warning or
cautionary statements
Visual / CPSD- HL-01057-
MTHD
All
Include, if required for safe
use Provided /
Evaluation Citation / Method
No. of
Samples Criteria Results Rating
Accuracy or adequacy of instructions
Visual / CPSD- HL-01057-
MTHD
All
Shall include assembly, use, maintenance, and safety information as required with no errors or spelling mistakes
M PASS
Accuracy or adequacy of instructions
Visual / CPSD- HL-01057-
MTHD
All
[Layout]
Shall be easy to follow
M PASS
* Labeling review - hazardous materials
16 CFR 1500.121 modified
1
[Touch up paint]
The product packaging will be reviewed in conjunction with the TRA report for hazardous material labeling.
The evaluation will include:
Type size and style (if submitted as printed packaging)
Color and contrast of all cautionary statements Presence of the signal word Presence of the statement of principal hazards
Prominence of signal word and statements of principal hazards
Presence of cautionary statement "Keep Out of the Reach of Children"
This evaluation does not confirm full compliance with 16 CFR 1500.121.
NA /
* Products requiring
special labeling 16 CFR 1500.14 1
[Touch up paint]
Certain substances are defined hazardous and require specific labeling statements. Test to the supplemental protocol TRGT-HL-PTCL-06573- US.
NOTE: Applicable to mobile materials such as liquids, pastes, putties, gels and powders.
NA /
ANALYTICAL
Evaluation Citation / Method
No. of
Samples Criteria Results Rating
* Total lead content in surface coatings
Consumer Product Safety
Improvement Act of 2008 / 16
CFR 1303 / CPSC-CH- E1003-09.1 / AOAC 974.02
modified / CPSD-AN- 00001-MTHD
-
All accessible surface coatings shall not contain lead in excess of 0.009%
(90ppm) of the weight of the total content of paint or surface coating.
Report actual results or include data table within report
Issue a program audit report Compositing is allowed as follows:
- Lead in Surface Coating Requirement = 90 ppm - Max. = 2 materials - Must meet 45 ppm due to composite concentration Wet paints are not allowed.
It is acceptable to request up to 15 samples or components. If the required amount of the tested substance cannot be acquired from 15 samples, the results will be negligible.
M
(See Test Result) PASS
Evaluation Citation / Method
No. of
Samples Criteria Results Rating
Toxicological risk assessment - document review
16 CFR 1500.3 / CPSD-GB- 00001-STIP01
--
[Touch up paint]
Products intended for use by children, including toys and parts of toys, shall not be toxic (acute), a skin irritant, eye irritant, corrosive, or a strong sensitizer. Products that are not intended for use by children must be labeled appropriately if a toxicological hazard is present. Toxicological Risk Assessment shall be conducted to substantiate the compliance of the regulation for the following components:
- All liquids, pastes, putties, gels and powders regardless of claim
- Other materials bearing a
"NON-TOXIC" claim on samples and/or its packaging
In lieu of testing, test report can be submitted if dated within five years.
Note: Vendor shall provide a list of ingredient and shall be responsible for the accuracy of information contained.
NA /
HAZARDS
Sharp points 16 CFR 1500.48
modified All
Shall not have accessible, potentially hazardous sharp points before or after use and abuse testing Modification = Expanded scope to other products
M PASS
Sharp edges 16 CFR 1500.49
modified All
Shall not have accessible, potentially hazardous sharp edges before or after use and abuse testing Modification = Expanded scope to other products
M PASS
FLAMMABILITY Flammability of
solids 16 CFR 1500.44 1 Shall meet < 0.1 inches per second (horizontal burning).
M
(D.N.I) PASS
PHYSICAL CHARACTERISTICS
Dimensions
Standard measure / CPSD-HL- 01056-MTHD
1
Report overall dimensions;
shall meet label claims (If applicable)
Dimension Tolerance
Less than or equal to 24 inch ±1/8 inch Greater than 24 inch
±1/4 inch
60ẰLăxă36ẰWăxă
30-1/8ẰH /
Evaluation Citation / Method
No. of
Samples Criteria Results Rating
Dimensions
Standard measure / CPSD-HL- 01056-MTHD
1
Report overall diameter;
shall meet label claims (If applicable) (-0% / +5%).
NA (Not Round
Table)
/
Weight
Standard measure / CPSD-HL- 01056-MTHD
1
Report overall weight; shall meet label claims
(If applicable) (-0% / +5%).
66.2 Lbs /
Glass top thickness
Standard measure / CPSD-HL- 01056-MHTD
1
[Raw edge]
Less than 7.6 mm thick tempered glass required greater than 7.6 mm thick tempered glass not required
NA
(No Glass Top) /
Glass top thickness
Standard measure / CPSD-HL- 01056-MHTD
1
[Encased]
Less than 4.6 mm thick tempered glass required greater than 4.6 mm thick tempered glass not required
NA
(No Glass Top) /
Material type
Visual / CPSD- HL-01057-
MTHD
All
As claimed
Rubber Wood,
MDF /
WORKMANSHIP
Defects
Visual / CPSD- HL-01057-
MTHD
All
Shall have no components missing, malformed, and/or fractured
M PASS
Defects
Visual / CPSD- HL-01057-
MTHD
All
Shall have no discernable surface degradation, including crazing,
shivering, denting, bubbles, cracks, stains, deformations, chips, fractures, heavy lines, waves, shear marks, scratches, scuff marks, indentations, or blisters.
M PASS
PERFORMANCE
Effects of extreme temperature change
In-house method / CPSD-
HL-01012- MTHD
1
24 hours at 0ºF and 120ºF - no failure or visual change.
Modification = Exposure time changed form 4 hours to 24 hours
M PASS
* Durability test for products with casters - cyclic
ANSI/SOHO S6.5-08 section
19
1
No structural damage or deformation. - 1000 cycles of 24 in stroke length.
Prior to testing identify the dimensional measurements taken. After testing identify the dimensional
measurement that has exceeded the allowable tolerance for deformation, record and report the dimensional measurement prior to and after testing. If necessary, attach a digital image of the sample.
NA
(No Caster) /
Evaluation Citation / Method
No. of
Samples Criteria Results Rating
Concentrated functional load test for primary surfaces
ANSI / SOHO S6.5-08 section
5.3
1
This test will evaluate the ability of an individual surface to withstand the concentrated functional loads to which it may be subjected. Apply the specified concentrated load described in Table 1 through a 12 in. diameter area 1in from the edge at its apparent weakest point.
Remove the load after 60 minutes and there shall be no loss in servicability and the extendable elements shall meet the pull force requirements of section 20.
M Top Surface:
60ẰLăxă36ẰW Test Load: 200
Lbs
PASS
Resistance to corrosion - metal components
ASTM B117-07 modified / CPSD-HL- 01010-MTHD
1
[Indoor use only]
Withstand 48 hours in 95%
RH (fog) at 100°F with no corrosion or visual change.
M PASS
Resistance to corrosion - metal components
ASTM B117-07 modified / CPSD-HL- 01010-MTHD
1
[Outdoor use product]
Withstand 24 hours in 1%
salt spray (fog) with no corrosion or visual change.
NA
(Indoor Use) /
Distributed functional load test for
individual surfaces
ANSI / SOHO S6.5-08 section
5.2
1
The purpose of this test is to evaluate the ability of a units individual surfaces to withstand static loads to which it may be subjected when in use. Depending on the component's surface classification, apply the distributed loads specified in Table 1 to each component, one at a time, as follows, primary surfaces, secondary surfaces, keyboard surfaces, and writing shelves.
Remove test loads after 60 minutes, there shall be no loss in serviceability and the extendable elements shall meet the pull force requirements of section 20
M Top Surface:
60ẰLăxă36ẰW Test Load: 1.5 Lbs/in.ăxă192ẰP
= 288 Lbs
PASS
Evaluation Citation / Method
No. of
Samples Criteria Results Rating
Drop test
ANSI/SOHO S6.5-08 section
10
1
No structural damage or deformation after each end is dropped from height per Table 3.
Prior to testing identify the dimensional measurements taken. After testing identify the dimensional
measurement that has exceeded the allowable tolerance for deformation, record and report the dimensional measurement prior to and after testing. If necessary, attach a digital image of the sample.
M Table Weight:
66.2 Lbs Drop Height: 5.9
in.
PASS
Horizontal rack test
ANSI/SOHO S6.5-08 section
8
-
[For un-ganged freestanding desks and tables </ = 72" in length]
The unit shall be supported within 152 mm (6 in.) of the raiseded end.
- Raise one end of the long axis of the unit as shown in Figure 8 until one end just clears the nap of the carpet.
- Pivot unit 90º and return it 90º to its original position.
- Repeat for 10 cycles at a rate of 1 to 2 cycles per minute.
- Raise the opposite end of the unit, pivot unit 90º and return it 90º to its original position.
- Repeat for 10 cycles at a rate of 1-2 cycles per minute.
- Perform the pull force test in section 20 on all extendible elements.
There shall be no loss of serviceability.
M PASS
Protective caps on legs
Visual / CPSD- HL-01057-
MTHD
1
Shall be non - marring
M PASS
Leg strength test - static
ANSI/SOHO S6.5-08 section
7
1
No loss of serviceability shall occur as a result of the force applications.
M Table Weight:
66.2 Lbs Force A: 0.5 x 66.2 Lbs
= 33.1 Lbs Force B: 0.5 x 33.1 Lbs
= 16.6 Lbs
PASS
Stability under vertical load
ANSI / SOHO S6.5-08 section
4.2
1
Shall remain stable. Shall not tip over (overturn) when a 125 lb load is applied 1"
from edge on a 12" disc.
M PASS
Stability for units with extendible load - bearing elements
ANSI / SOHO S6.5-08 section
4.3
1
Shall comply with the
requirements of the section NA /
Evaluation Citation / Method
No. of
Samples Criteria Results Rating
Leg strength - folding table
ANSI/SOHO S6.5-08 section
7
1
No structural failure at 40 lb applied vertically to the leg at 1 in. from the end of the leg. Force is applied in four directions (forward, rearward, and side to side).
NA (Not Folding
Table)
/
Stain resistance
ASTM D543 / ASTM D3023
modified
1
No objectionable stain by most household stains after 2 hours placement: wine, ketchup, grape juice cooking oil
No objectionable stain by most household stains after 1 hour placement: mustard
M PASS
Resistance to hot water
ASTM D1308- 02 section 6.1.2
and 7
1
Place a small portion of distilled hot water on a horizontal surface, wait (1) hour, wipe the spot clean and examine for alterations in the surface including discoloration, changes in gloss, blistering, softening, swelling, loss in adhesion, or other special phenoma.
M PASS
* Ease of assembly
In-house method / CPSD-
HL-03027- MTHD
1
Shall provide ease of assembly and shall be accurate
M PASS
Moisture content
In-house method / CPSD-
HL-01063- MTHD
1
[Solid wood, MDF and particle board]
Shall not exceed For indoor use: 6 - 12%
For outdoor use: 10 - 15%
Three separate readings are required and shall be recorded in the report.
M Indoor Use:
Rubber Wood:
8.6%, 8.9%, 8.8%
MDF: 7.3%, 7.3%, 7.2%
Particle Board:
NA (No Particle Board)
PASS
NOTE: It is the vendor's responsibility to ensure that the products they sell to Target Corporation comply with all United States federal, state, and local laws, regulations and ordinances. A satisfactory Lab test result does not constitute a certification that a vendor's products meet all legal requirements. It is the vendor's responsibility to manufacture their items to comply with all applicable laws and in conformance with the purchase order terms and conditions on Partners Online.
Key:
* Additional Charge For This Test
** Mandatory Requirement
# By Request Only
Result Key:
M Meets
NM Does Not Meet
NA Not Applicable
NT Not Tested
Rating Key:
SAT Satisfactory
UNSAT Unsatisfactory
No. Of Samples Required for Complete Testing
2 No. Of (Fully Packed) Cartons For Transit Testing:
1 No. Of Working Days For
Complete Testing:
7
Client Approval: OCTOBER 10, 2011 / Chris Thomas Creation Date: FEBRUARY 17,
2003 Last Revision
Date:
OCTOBER 11, 2011
Pricing Review Date:
AUGUST 26, 2009 Technical
Review Date:
Evaluation Citation / Method
No. of
Samples Criteria Results Rating
SCOPE:
This protocol contains packaging and labeling requirements. (Target dept 55 and 219 are excluded from TRGT-9067 and only the CARB and plastic bag warning test lines should be used for Target.com)
LABELING
Principal Display Panel (PDP) Additional Information:
The Principal Display Panel (PDP) shall be defined by location and area per the following:
PDP Location = The side of the packaging that is displayed to the guest when shelved.
Hangtags PDP shall be defined as the side where both Product Name / Description and Net Quantity/Count appear.
PDP Area = The total area where printed material exists on the PDP location. For example, the PDP of a large boxed TV would be just the size of the sticker on the box.
--- Open Stock Additional information:
Open stock is defined as items that are unenclosed in packaging, where guest can fully view and touch product including the product's full dimensions and all required Target labeling per this protocol.
--- Mock-up Packaging Additional Information:
If vendor is using packaging designed by Target and it is not complete at time of testing, mock-up packaging will be accepted. If mock-up packaging is submitted, it must be clearly legible and must include all regulatory requirements stated in this protocol. Handwritten mock-up packaging is NOT acceptable. Warnings or other regulated labeling must appear in their proper location on mock up packaging. If these regulated warnings and labeling have sizing requirements, a separate "to scale" copy of these warnings and labeling can be submitted at the same time as the not-to-scale mock up packaging.
Product name or description
FPLA or UPLR / Target
requirement
1
Product Name / Description shall be shown on PDP including open stock.
Product Name/Description must be on open-stock gift bags and gift boxes, but is not required to be on the PDP.
NA /
Declaration or responsibility, distribution statement, country of origin - package or hangtag
19 CFR 134 / Target requirement
1
Report Declaration of Responsibility, Distribution Statement and COO. Shall be shown on package or hangtag
NA /
Declaration or responsibility, distribution statement, country of origin - sewn-in tag or label
19 CFR 134 / Target requirement
-
If Sewn-in tags are required, it shall include COO and the Registered Identification Number (RN). If distributed by Target, shall use Target RN per the following:
RN17730
OR list the following statement instead of an RN:
Distributed by Target Corporation, Minneapolis, MN 55403
If Sewn-in tag is not required, but COO statement is present, rate as data.
Client requirement
NA /
Evaluation Citation / Method
No. of
Samples Criteria Results Rating
Net quantity or count
FPLA or UPLR / Target
requirement
1
Net quantity shall be present on the package in terms of weight or mass, distance or length, capacity or volume, area, piece count or a combination of these units of measurement.
The lab will verify the presence or absence and accuracy of the net quantity.
Open Stock (defined above) is exempted from this requirement.
Vendor note: Net Quantity / Count shall be expressed in terms that will be most descriptive to user's end- use. Target merchant will determine if the vendor should use count or dimensions.
Example: Garden Hose = 25 ft (7.6 m),
Pencil = 10 pencils or 10 count,
Beverage Drinking Glass = 32 fl oz (946 mL),
Glassware Set = 4 - 32 fl oz (946 mL) glasses.
For items using protocol 8266: Do not verify labeled dimensions. Must have piece count listed, otherwise fail.
NA /
Net quantity or count
Visual / CPSD-HL- 01057-MTHD
-
Net Quantity / Count weights & measurements shall be represented in both English units and metric units. Metric units shall be placed immediately to the right of English units or on next line below. Metric units shall be enclosed within parentheses or brackets. Vendor Note The absence of the metric units in parentheses or brackets will result in a failure.
Example: 4 in x 4 in (10 cm x 10 cm) or 18 in H x 12 in W x 4 in D (45.7 cm x 30.4 cm x 10.1 cm)
NA /
Evaluation Citation / Method
No. of
Samples Criteria Results Rating
Net quantity or countVisual / CPSD-HL-01057-MTHD- Net Quantity / Count weights & measurements shall follow "Rule of 1 to 1000." Use units that, when converted, result in numerical values between 1 and 1000. Example: 48 in = 121.9 cm NOT 48 in = 1219 mm, 5 in = 12.7 cm NOT 5 in = .127 m
NA /
Net quantity or countVisual / CPSD- HL-01057- MTHD 1
Net quantity shall not use periods in abbreviations and shall not use symbols for units (such as ',#, or the like) This does not apply to weights and measurements used in the Product Name / Description, descriptive copy, or charts and tables.
Vendor Note-Product Name / Description, descriptive copy, or charts and tables do not replace requirement for Net Quantity / Count.
NA /
Net quantity or countVisual / CPSD-HL-01057- MTHD1
Report claimed net quantity verbatim.
NA /