TÀI L IU THAM KHO
TING V IT
[1]Ph m thị εinhăPhương-T VĕnăThất , Công nghệ nhiệt luyện, Nhà xuất b n giáo
d c, 2000, trang 220-240
[2] Lê Hoàng Anh ,Phân tích các yếu tố nh h ởng đến độ rộng đ ờng nhiễu x tia X – quang, Thực hiệnănĕmăβ008ăt iăđ i học SPKT TP HCM.
[3] DươngăCôngăCư ng, Nghiên cứu và xác định độ cứng của thép cacbon nhiệt luyện bằng ph ơng pháp nhiễu x tia X, thực hiệnănĕmăβ01γăt iăđ i học SPKT Tp.HCM
[4]Nguyễn Chung C ng, sổ tay nhiệt luyện, NXBăKhoaăHọcăăKỹăThuật,ăβ007. [5]Nghiêm Hùng, sách tra cứu thép gang thông dụng,ăĐ i học bách khoa Hà Nội, 1997.
[6]Phùng Rân, Quy ho ch thực nghiệm ứng dụng,ăĐ i họcăsưăph m kỹ thuật Tp. Hồ Chí Minh, 2006.
[7]Lâm Bá Nha, Giáo trình vật liệu hoc, Đ i học Trà Vinh,2014.
TI NG N C NGOÀI
[8]L.C. Cuong and M. Kurita , Absorption Factor And Influence of LPA Factor On
Stress And Diffraction Line Width In X-Ray Stress Measurement With and Without Restriction Of X-Ray Diffraction Area, The Japanese Society for Experimental
Mechanics, 2004, trang 7-14.
[9]Victor Hauk ,Structural And Residual Stress Analysic By Nondestructive
76
[10] Kurita, M., X-Ray Stress Measurement By The Gaussian Curve Method, X-Ray
Diffraction Studies On The Deformation And Fracture Of Solids, Current Japanese
Materials Research, Vol.10, 1993,trang 135-151.
[11] EL-Hossary và S.Mändl , Effect of annealing temperature on hardness,
thickness and phase structure of carbonitrided 304 stainless steel, material
science& Processing, 2000
[12]F.M.El-Hossary,N.Z.Negm,S.M.Khali,A.M.AbedElrahman,D.N.McIlroy,RF
plasma carbonitriding of AISI 304 austenitic stainless steel, Surface and Coatings technology, 2001
[13] F.M.El-Hossary,M.Raaif, ,A.A.Seleem, M.Abo El-Kassem A.M.Abd El- Rahman,D.N.McIlroy ,Effect of rf Plasma Carbonitring on the Biocompatibility and
Mechanical Properties of AISI 321 Austenitic Stainless Steel,Scientific
research,2014
[14] T.Kumar, P.Jambulinggam, M.Gopal and A.Rajadural ,Surface hardening of AISI 304, 316, 304L and 316L SS using Cyanide free salt bath nitriding process,2004
[15] D.J.Hornbach, et.al., X-ray Diffraction Chacracterization of the Residual Stress and Hardness Distributions, First Int. Conf. on Induction Hardened Gears
and Critical Components, May 15-17, Indianapolis Gear Research Institute, 1995, trang 69-76
[16]B.D Cullity, S.R.Stock, Elemens of x-ray diffraction,2001
[17]Jing Shi and C. Richard Liu, Decomposition of Thermal and Mechanical
Effects on Microstructure and Hardness of Hard Turned Surfaces, School of
77 PH L C