the federal motor vehicle safety standards

... is, in the line of the stroke They will have their greatest value at the ends 28 The Motor Vehicle of the stroke, in opposite directions, and become nothing in the middle of the stroke Referring ... transmitted to the upper end of the connecting rod through the ‘gudgeon pin’on which the ‘small end’ of the connecting rod is free to swing Fig 1.1 Fig 1.2 The Motor Vehicle Connecting rod The connecting ... break when the piston was approaching the top of the cylinder, the engine running at a high speed, the piston would tend to fly through the top of the cylinder just as, if the cord broke, the mass...

Ngày tải lên: 14/03/2014, 16:20

... is, in the line of the stroke They will have their greatest value at the ends 28 The Motor Vehicle of the stroke, in opposite directions, and become nothing in the middle of the stroke Referring ... transmitted to the upper end of the connecting rod through the ‘gudgeon pin’on which the ‘small end’ of the connecting rod is free to swing Fig 1.1 Fig 1.2 The Motor Vehicle Connecting rod The connecting ... break when the piston was approaching the top of the cylinder, the engine running at a high speed, the piston would tend to fly through the top of the cylinder just as, if the cord broke, the mass...

Ngày tải lên: 14/03/2014, 18:20

... gasoline, oil, and grease The number indicates the amount of the ex- Pyrotechnic Devices: tinguishing agent contained in the extinguisher; the higher the number, the greater the amount of agent in the extinguisher ... swimmers or other persons in the water Keep those in the water on • Seat any passengers on the bottom of the boat, near the center line • If the engine fails, trail a sea anchor from the bow of the boat ... of the water If the exhaust pipes become immersed in the water, the blower for at least four minutes Check the bilges for fuel the engine may stall vapors before starting the engine Do the “sniff test” to make sure...

Ngày tải lên: 17/03/2014, 14:20

... ■■ ■■ the weight and shape of the glass; the height from the floor and angle of the vehicle aperture, which determines the arm extension and posture required by the technician to position the glass; ... decontaminant recipes in the product’s safety data sheet, or ask the product maker for advice Further information on SMART spraying 134 Further details are given in the free publication Motor vehicle repair: ... lever, removes each of the tyre beads from the wheel rim Fitting the tyre is the reverse operation, using a different tool on the end of the lever 162 The machine has the potential to trap operator’s...

Ngày tải lên: 30/03/2014, 09:20

... is, in the line of the stroke They will have their greatest value at the ends 28 The Motor Vehicle of the stroke, in opposite directions, and become nothing in the middle of the stroke Referring ... transmitted to the upper end of the connecting rod through the ‘gudgeon pin’on which the ‘small end’ of the connecting rod is free to swing Fig 1.1 Fig 1.2 The Motor Vehicle Connecting rod The connecting ... break when the piston was approaching the top of the cylinder, the engine running at a high speed, the piston would tend to fly through the top of the cylinder just as, if the cord broke, the mass...

Ngày tải lên: 27/06/2014, 17:20

... is, in the line of the stroke They will have their greatest value at the ends 28 The Motor Vehicle of the stroke, in opposite directions, and become nothing in the middle of the stroke Referring ... transmitted to the upper end of the connecting rod through the ‘gudgeon pin’on which the ‘small end’ of the connecting rod is free to swing Fig 1.1 Fig 1.2 The Motor Vehicle Connecting rod The connecting ... break when the piston was approaching the top of the cylinder, the engine running at a high speed, the piston would tend to fly through the top of the cylinder just as, if the cord broke, the mass...

Ngày tải lên: 27/06/2014, 18:20

... thimble over the end of the stem, seating its rim on the retainer washer for the spring, so that there is a small clearance between the tip of the stem and the other end of the thimble When the cam ... push the three-piece hydraulic plunger to the right, locking all three together In this condition, the central cam, because it is higher than the other two, actuates the valves In the graph (b) the ... surrounding the slightly dished portion of the crown of the piston and the flat lower face of the casting, each side of the pairs of valves Because of the steepness of the slope of the inlet ports,...

Ngày tải lên: 11/08/2014, 20:21

... one to drive the spindle for the water pump installed vertically in the V, and the other for the spindle driving the ignition distributor – inclined towards the left in the V – and the oil pump, ... design 214 The Motor Vehicle that, if the control rod is moved beyond the limit set by the maximum fuel stop, it is the base of this slot instead of the upper edge of the plunger that closes the inlet ... filter to the engine, while the other half passes through the relief valve, which lifts at 483 kN/m2, to the oil cooler integral with the filter housing at the front end of the sump The return...

Ngày tải lên: 11/08/2014, 20:21

... through the solenoid When the current to the solenoid is cut, the valve is closed by its return spring and the pressure in the tiny volume of the valve control chamber rises 248 The Motor Vehicle ... passages: one to the injection pump and the other to the latch valve 13 in Fig 7.9 When the engine is turned by the starter motor, the fuel from the transfer pump is also delivered to these two passages, ... spring seats on the other The position of the diaphragm therefore depends on the force exerted by the boost pressure against the spring A push rod connected to the diaphragm slides the link plate...

Ngày tải lên: 11/08/2014, 20:21

... a pulley on the front end of the crankshaft On the other hand, the oil pump is interposed between the toothed wheel for the HTD drive and the crankcase wall and driven by a gear on the crankshaft ... without oil cooling of the underside of the piston crown 322 The Motor Vehicle Fig 8.8 On the Cummins engine, the two outer rockers actuate the valves and the central one the injector Rocker type ... downstream into the air The toroidal recess in the piston crown has the effect of increasing the rotational swirl when the piston reaches the top of the stroke, on the principle of the conservation...

Ngày tải lên: 11/08/2014, 20:21

... by the proximity of the edge of the throttle to them As the throttle is opened further, the increasing depression in the venturi brings the main system into operation From the main jet G, the ... from the float chamber, through the power jet into the emulsion system An air 380 The Motor Vehicle To throttle F F (a) (b) Fig 10.25 bleed hole in the plug in the end of the passage delivering the ... of the fuel in the jets In any case, the inertia of the fuel in the delivery system from the jets will cause delivery to lag behind the increase in depression Furthermore, the opening of the...

Ngày tải lên: 11/08/2014, 20:21

... senses the passage of either a pin or hole in the flywheel These two signals are processed in the control unit to make them compatible with the computer The parameters on the basis of which the ... the temperature of the incoming air rises above 35°C, the Thermac valve opens, to vent the depression to the clean side of the air filter A restrictor in the connection from the manifold to the ... The Motor Vehicle range, to satisfy the US Federal regulations until at least 1996 At the same time, the old A-Series engine in the Mini Cooper was similarly equipped, mainly for satisfying the...

Ngày tải lên: 11/08/2014, 20:21

... general use One is the research octane number (RON) and the other the motor octane number (MON) There is also a third, applicable to the vehicle rather than the fuel, and this is termed the road octane ... the other in the tower, Fig 17.6: the heaviest fuels (those having the lowest boiling point) condense into the lowest and the others into each tray in turn, until the lightest come out into the ... over-heated The low pressure both inside the pump and in the pipeline between it and the tank 598 The Motor Vehicle reduces the boiling point of the fuel, so heat transmitted to these components...

Ngày tải lên: 11/08/2014, 20:21

... released a little then the oil pressure on the left-hand end of the valve will move the valve to the right, thus uncovering the exhaust port The pressure in the line will then fall until the spring ... the valve can move back to the left the force on F due to the governor pressure must fall below the force on 832 The Motor Vehicle E due to the throttle valve (or the latter must rise above the ... coupled by the shaft G to the sun S2 of the second epicyclic train If the annulus of the train is fixed then the sun S2 will drive the planet carrier R2, which is the output member of the box,...

Ngày tải lên: 11/08/2014, 20:21

... are fitted, the lost traction is transferred to the other wheel on the same axle, the front wheels continuing to transmit their 882 The Motor Vehicle share of the drive However, if either front ... its pin while the forces P/2 appear as pressures between the teeth of the bevel pinion and the bevel wheels 878 The Motor Vehicle 31.1 Another arrangement of the bevel final drive The bevel final ... metal pressings which form the ring of the joint are assembled together These pressings are held together by spinning the lips of one of them over those of the other The design in Fig 30.8 is...

Ngày tải lên: 11/08/2014, 20:21

... that other things being equal the smaller the height OG the less the overturning couple The magnitude of the righting couple QQ is Q × SS, so that the greater the wheelbase SS the less the force ... 976 The Motor Vehicle towards the centre of the vehicle the compensation between the two sides is most easily effected by one of the arrangements shown in Fig 37.29 The principle of both of these ... (LSD) in 950 The Motor Vehicle Chapters 31 and 39 If the wheels lock, the coefficient of friction between the tyres and the road becomes lower than when they are rolling, and the vehicle is liable...

Ngày tải lên: 11/08/2014, 20:21

... the driver releases the brake pedal, a switch breaks the circuit to the solenoid to cut out the boosting effect of the servo 1010 The Motor Vehicle factors include the speed of the vehicle, the ... construction of the tyre itself, the value of the vertical force between the tyre and the road (referred to in what follows as the load on the tyre), the inflation pressure, the size of the tyre and the ... brake is applied on that side, but if the wheel on the other side then spins, the electronic control closes the throttle or reduces the 1024 A K B J The Motor Vehicle H C D G E F G A B C D E Hydraulic...

Ngày tải lên: 11/08/2014, 20:21

... tyre markings The aspect ratio is the inverse of the ratio of the width to the height of the crown of the tyre above the edge of the bead that seats on the rim Modern 1102 The Motor Vehicle tyres ... between the ECU, motor and sensor 1078 The Motor Vehicle Such units can be fully tested by their manufacturers, ready for installation in the vehicle Because there is only one item per vehicle, the ... these signals represent the speed of rotation of the steering wheel Other inputs from sensors to the ECU include the torque being delivered by the electric motor, the resistance torque from the...

Ngày tải lên: 11/08/2014, 20:21

... of the vehicle If we then the same for the suspension on the other side, we find that the two lines OT 1148 The Motor Vehicle O O C T T C O at infinity C T Fig 43.3 Note: If the suspension on the ... 1152 The Motor Vehicle back through the swinging halfshaft to the brakes Since the stub axle carrier pivots about the outer end of the lower link, the vertical loads applied at the wheel put the ... Normally the two torsion bars, one for the left-hand and the other for the right-hand arms, are attached one at each of the pivots X of the arms A, and their other ends are anchored to the frame or vehicle...

Ngày tải lên: 11/08/2014, 20:21

... whether patient injury pattern and severity is associated with e.g accident type, mechanical distortion of the vehicle, unrestrained objects in the vehicle, and seat-belt use Here, we hypothesized ... in the hospital paper archives was performed 2.3 Eligibility criteria Based on the dispatch criterion motor vehicle accident - suspicion of serious injury or death,” the EMCC notified one of the ... from the motor vehicle Collection of mechanical data was performed in collaboration with the police and the Norwegian Public Road Accident groups and was both elaborate and labour demanding Therefore,...

Ngày tải lên: 25/10/2012, 09:56