snap fit designs for plastic injection molding

... local 1D transient analysis is performed for the plastic part using an implicit finite difference method with a variable mesh. An iterative procedure is developed for coupling the cycle- averaged ... less unwanted informa- tion about internal points is obtained. Therefore, the BEM is particularly well suited for mold cooling analysis. The boundary integral equation (BIE) for Eq. (1) can be written ... optimal design in plastic injection molding H. Qiao à Cardiff School of Engineering, Queen’s Buildings, The Parade, PO Box 925, Cardiff, CF24 0YF, UK Received 10 December 2003; received in revised form 10...

Ngày tải lên: 12/02/2014, 22:20

... melt and a near uniform cooling performance can be achieved. 5 Results of scaffold cooling performance The advent of computer-aided engineering (CAE) technol- ogy for plastic injection moulding ... as for rapid plastic injection mould. 5.1 Cooling performance investigation of cooling channel by meltflow analysis Cooling performance analysis will find the temperature distribution in a plastic ... configuration within the injection mould. However, LST moulds are used only for low melting thermoplastics and are not appropriate for the injection- moulding process with thermosetting plastics or high-temperature...

Ngày tải lên: 12/02/2014, 22:20

Ngày tải lên: 28/06/2014, 15:20

... FiberGuide đ Snap- Fit Junction ADCs FiberGuide đ System is the industrys most comprehensive fiber raceway system. ... supporting strength and provides superior protection to critical fiber cables. ADC’s FiberGuide Snap- Fit Junction is a completely tool-less junction. With no additional tools needed to install or ... junction is ready to install immediately upon arrival. Quick, and easy to use, the FiberGuide Snap- Fit Junction saves installers valuable time and money. Features: ã Reduces installation time...

Ngày tải lên: 18/10/2013, 20:15

... percentages for each experiment, the orders of the simulated and physical experiments agree for the top three outcomes. These are the most significant, since they account for over 95% of the outcomes. For ... gives the matrix for the corresponding physical experiment. 4.2 Stochastic Matrices Figures 6 and 7 show results for three simulated and ac- tual mid-sizedcylinder experimentsperformed on the single Slope ... Simulated Designs for Vibratory Parts Feeding Dina R. Berkowitz  John Canny  dberk@cs.berkeley.edu jfc@cs.berkeley.edu Department of Electrical Engineering and Computer Science University of California,...

Ngày tải lên: 03/01/2014, 19:15

... Bushing Hot Runner Systems Injection Molding Tooling Valve Gate Shut Off System Bushings are Opened for Injection Recommended runner sizes Optimizing Cycle Time Source: Injection Molding Magazine article Source: ... cosmetic surface may cause surface imperfections. Source: GE Plastics It is suggested that direct gates not be used in molding reinforced resins into rectangular shapes. Fiber orientation may result ... Considerations ã Molding Cycle.80% is cooling time ã Flow type.Laminar or Turbulent ã Flow rateGPM ã Reynolds number of > than 5000 for turbulent flow ã Thermal conductivity of mold steel ã Plastic...

Ngày tải lên: 06/01/2014, 21:03

... performance measure (as illustrated in Figure P.2). For example, the physical layer is responsible for the reliable and efficient deliv- ery of information bits. The MAC layer is responsible for ... xxxi tation can be performed at the MIMO transmitter. In fact, the adaptation across the spatial domain contributes to significant performance gains over open-loop performance and therefore has received ... MAC layer designs for wireless systems follow the isolated approach where there is no cross-optimization across the physical layer and the MAC layer. For instance, a lot of research effort has...

Ngày tải lên: 01/06/2014, 07:54

... device, Biochemical Engineering Journal 13 (2003) 113–125 Bioreactor designs for solid state fermentation A. Durand ∗ Platform for Development in Biotechnology, UMR-INRA 1082 (IBQ), 17 Rue Sully, ... between lab-scale and industrial-scale designs. It highlights the main designs that have emerged over the last 10 years and the potential for scaling-up for each category of reactor. â 2002 Elsevier ... processes are developed. Finally, for some industrial applications (production of spores for cheese making for example), SSF constitutes the sole so- lution for a production process and now,...

Ngày tải lên: 12/06/2014, 11:37

... error performance in practice, it gives an SER lower bound for this channel. For OFDM, by setting σ 2 s = P peak and assuming no clipping happens, Monte Carlo simulation gives the SER curve for this ... decision s is obtained by hard decoding on s,denoted as s =s. Therefore, for uncoded SIMO-OFDM, MRC is essen- tially the zero-forcing (ZF) and also the maximum- likelihood (ML) equalizer in the ... antenna diversity [10], for example, maximal ratio combining (MRC) and selective combining (SC). Before discussing the peak-power-limited case, we briefly review the MRC method for the linear SIMO- OFDM...

Ngày tải lên: 21/06/2014, 18:20

... transceiver designs for multiuser MIMO downlink in the presence of imperfect CSIT. We consider two widely used models for the CSIT error [21], and propose robust THP transceiver designs suitable for ... transceiver design for SE model of CSIT error is presented in Section 3.Theproposed robust transceiver designs for NBE model of CSIT error are presented in Section 4. Simulation results and performance comparisons ... designs under SE and NBE models for CSIT errors. For the SE model, we proposed a minimum SMSE transceiver design. For the NBE model, we proposed three robust designs, namely, minimum SMSE design,...

Ngày tải lên: 21/06/2014, 20:20

... channels, Ph.D. thesis, Stan- ford University, Stanford, Calif, USA, May 2001. [7] A. Scaglione, P. Stoica, S. Barbarossa, G. B. Giannakis, and H. Sampath, “Optimal designs for space-time linear precoders and ... based on full channel knowledge for MIMO systems in frequency-flat and -selective channels has been investigated by many works. For a detailed overview on the designs for frequency-flat channels, see ... Therefore, the precoder stru cture can be written as W = ΦΣ 1/2 Γ, (16) where Γ is an arbitrary unitary matrix that has no effect on the system performance, and therefore can be set to iden- tity for...

Ngày tải lên: 22/06/2014, 19:20

Ngày tải lên: 28/06/2014, 09:20

Ngày tải lên: 05/07/2014, 20:21

Ngày tải lên: 11/08/2014, 17:21

Ngày tải lên: 11/08/2014, 20:20

Ngày tải lên: 14/08/2014, 13:22

Ngày tải lên: 14/08/2014, 19:22

Ngày tải lên: 14/11/2014, 13:26