... disabling their one context menu handler.
Note that the above key only applies to the rightclickmenu of files.
To remove entries from the rightclick context menu of folders, you need to ... registry, refresh, and rightclick a file to see if the item was removed from
the menu.
Some programs - like WinZip or WinRar - will add several items to your rightclickmenu
but all of them ... How To Remove and Add Right- ClickMenu Items from Files and Folders
Removing Items
A lot of programs you install will add themselves to the right- clickmenu of your files
and/or folders....
... RightClick Tweaker là một phần mềm miễn phí trên Windows có chức
năng bổ sung thêm nhiều tiện ích vào menu chuột phải khi người dùng nhấn
chuột phải ... Thay đổi tên tập tin hàng hoạt trong một thư
mục.
Bổ sung thêm chức năng
cho menu chuột phải với
Right Click Tweaker
... tập tin,
thư mục hoặc chuột phải lên Desktop, khoảng không trên màn hình.
Các chức năng của RightClick Tweaker:
1. Copy To Folder: Sao chép di chuyển tập tin/thư mục sang một thư
mục khác....
... reserves the right to remove additional content at any time if subsequent rights restrictions require it.
BRIEF CONTENTS
INTRODUCTION LI
UNIT I — SETTING UP DRAWINGS 1
1 QUICK TOUR OF AUTOCAD2011 3
2 ... Cengage Learning reserves the right to remove additional content at any time if subsequent rights restrictions require it.
Copyright 2010 Cengage Learning. All Rights Reserved. May not be copied, ... Learning reserves the right to remove additional content at any time if subsequent rights restrictions require it.
xlviii
B AutoCAD Commands, Aliases, and Keyboard
Shortcuts 981
AUTOCAD COMMANDS...
... 65,220
right- click
Specify next point: drag to right enter 240
right- click
Specify next point: drag down enter 145 right- click
Specify next point or [Undo]: drag left enter 65
right- click
Specify ... 2011
CHAPTER 1
4
Opening AutoCAD2011AutoCAD2011 is designed to work in a Windows operating system. In
general, to open AutoCAD 2011, double -click on the AutoCAD2011
shortcut in the Windows ... 60,210
right- click
Specify next point or [Undo]: enter @50,0
right- click
Specify next point or [Undo]: enter @0,20
right- click
Specify next point or [Undo/Undo]: enter @130,0
right- click
Specify...
... left-clicked
2 Pull-down menu items which display ᭤ result in a further menu when selected. This is
termed the cascade menu effect.
3 Menu items in BOLD type are available for selection.
4 Menu ... objects
respond right- click.
5 The objects highlighted will be erased – Fig. 5.7(d).
26 Beginning AutoCAD 2002
Beginning with AutoCAD 2002.qxd 14/06/2002 19:04 Page 26
1 Start AutoCAD and:
prompt ... the instructions given in the AutoCAD 2002
Users’ Manual.
4 Beginning AutoCAD 2002
Beginning with AutoCAD 2002.qxd 14/06/2002 19:03 Page 4
Menu bar notes
1 Pull-down menu items which display ‘…’...
... 65,220
right- click
Specify next point: drag to right enter 240
right- click
Specify next point: drag down enter 145 right- click
Specify next point or [Undo]: drag left enter 65
right- click
Specify ... 230,100
right- click
Specify next point or [Close/Undo]: enter 230,70
right- click
Specify next point or [Close/Undo]: enter 120,70
right- click
Specify next point or [Close/Undo]: enter 120,100
right- click
Specify ...
right- click
Specify next point or [Close/Undo]: enter 55,100
right- click
Specify next point or [Close/Undo]: enter 55,210
right- click
Specify next point or [Close/Undo]: enter c
(Close) right- click
Command:
The...
... next point: right- click
Command: right- click
PLINE
Specify start point: pick near the middle of first
pline
Specify next point: 155,120
Specify next point: right- click
Command: right- click
PLINE
Specify ... 1
Specify ending width <1>: right- click
Specify next point: 260,230
Specify next point: right- click
Command: right- click
PLINE
Specify start point: pick the right- hand end of
the pline
Specify ... any of the AutoCAD2011
workspaces, some operators may prefer a larger working area. To achieve
this a click on the Clean Screen icon in the bottom right- hand corner
of the AutoCAD2011 window...
... enter dim right- click
Dim: enter l (Leader) right- click
Leader start: enter nea (osnap nearest)
right- click to pick one of the chamfer
lines
To point: pick
To point: pick
To point: right- click
Dimension ... total
Select objects to join to source: right- click
Introduction to AutoCAD2011
chapter 5
120
Select objects or <select all>: pick 1 found
Select objects: right- click
Select object to extend or ... entered. A right- click does not
work.
2. At the prompt:
Specify start point of text or [Justify/Style]:
enter s (Style) right- click
Enter style name or [?] <ARIAL>: enter ?
right- click
Enter...