Bộ đề thi chứng chỉ Solidworks CSWPA Sheet Metal dành cho các bạn có nhu cầu thi để lấy chứng chỉ Solidworks quốc tế. Bộ đề thi chứng chỉ Solidworks Sheet Metal,Bộ đề thi chứng chỉ Solidworks Sheet Metal,Bộ đề thi chứng chỉ Solidworks Sheet Metal,Bộ đề thi chứng chỉ Solidworks Sheet Metal.
Solidworks CSWPA Sheet Metal Certification Exam Set Nguyễn Phước Lợi November 18, 2021 Question of 15 For 10 points: 43.50 A1004 - Model the base part (starting with a Base Flange) Unit system: MMGS (millimeter, gram, second) Decimal places: Part origin: Arbitrary Material = Aluminum Alloy, 1060 Alloy, Density = 0.0027 g/mm^3 Sheet Metal Thickness: 1.50 mm Inner Bend Radius = 1.00 mm All corners are open with gaps between flanges = 1.00 mm A = 193 mm B = 190 mm C = 74 mm |- Measure the mass of the resulting Sheet Metal part What is the mass of the Sheet Metal part (grams)? of 352.16 grams O 358.76 grams O 371.42 grams O 362.85 grams Previous Question Reset Ouestion A Show Summary Next Question Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 Question of 15 For points: 80 B A2004 - Close the corners Unit system: MMGS (millimeter, gram, second) Decimal places: Part origin: Arbitrary Material = Aluminum Alloy, 1060 Alloy, Density = 0.0027 g/mm3 Sheet Metal Thickness: 1.50 mm Inner Bend Radius = 1.00 mm Closed Corner Gap = 0.20 mm, Full Overlap, Open Bend Region Front and Rear Flanges will overlap the Side Flanges (See Detail image) Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 43.50 A = 193 mm B = 190 mm C = 74 mm -Measure the mass of the resulting Sheet Metal part What is the mass of the Sheet Metal part (grams)? Enter Value: (use (point) as decimal separator) Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 Question of 15 For points: A3002 - Flatten the part Unit system: MMGS (millimeter, gram, second) Decimal places: Part origin: Arbitrary Material = Aluminum Alloy, 1060 Alloy, Density = 0.0027 g/mm3 Sheet Metal Thickness: 1.50 mm Inner Bend Radius = 1.00 mm General K-Factor = 0.32 43.50 A = 195 mm B = 205 mm C = 72 mm |- Measure the distance X of the part when flattened (See last image.) What is the distance X of the part when flattened? 352.11 mm O 343.65 mm O 339.69 mm O 322.34 mm Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 Question of 15 For 20 points: 80 135° A4004 - Add feature Unit system: MMGS (millimeter, gram, second) Decimal places: Part origin: Arbitrary Material = Aluminum Alloy, 1060 Alloy, Density = 0.0027 g/mm3 Sheet Metal Thickness: 1.50 mm Inner Bend Radius = 1.00 mm Rectangular Bend Relief: Width = 1.00 mm x Depth = 1.00 mm 135 43.50 42.50 A = 193 mm B = 190 mm C = 74 mm |-Measure the mass of the resulting Sheet Metal part What is the mass of the Sheet Metal part (grams)? 51.50 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 Enter Value: (use (point) as decimal separator) Question of 15 For points: A5001 - Flatten the part Unit system: MMGS (millimeter, gram, second) Decimal places: Part origin: Arbitrary Material = Aluminum Alloy, 1060 Alloy, Density = 0.0027 g/mm^3 Sheet Metal Thickness: 1.50 mm Inner Bend Radius = 1.00 mm A = 200 mm, B = 200 mm, C = 70 mm -Change the part's K-Factor to 0.48 -Measure the maximus measured extent (X) of the part when flattened (See layimage.) Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 What is the maximum measured extent (X) of the part when flattened? 0468.23 mm O 477.56 mm O 492.23 mm 0486.96 mm Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 Question of 15 QK For 15 points: 80 A6001 - Add support flange Unit system: MMGS (millimeter, gram, second) Decimal places: Part origin: Arbitrary Material = Aluminum Alloy, 1060 Alloy, Density = 0.0027 g/mm^3 Sheet Metal Thickness: 1.50 mm Inner Bend Radius = 1.00 mm 43.50 Note: Top of support flange should be even with bottom of rectangular opening (See section view EE) A = 200 mm B = 200 mm C = 70 mm Z |- Measure the mass of the resulting Sheet Metal part 45151.56 51.50 What is the mass of the Sheet Metal part (grams)? Enter Value: Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 (use (point) as decimal separator) 10 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 Question of 15 For points: 80 A7002 - Flatten part Unit system: MMGS (millimeter, gram, second) Decimal places: Part origin: Arbitrary Material = Aluminum Alloy, 1060 Alloy, Density = 0.0027 g/mm^3 Sheet Metal Thickness: 1.50 mm Inner Bend Radius = 1.00 mm 43.50 A = 196 mm B = 210 mm C = 69 mm - Maintain the part's K-Factor at 0.48 11 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 -Flatten the part Note: There should be no interference after the part is flattened V 51.56 |- Measure the maximum measured extent (x) of the part when flattened (See last image.) 501.06 mm 0491.35 mm 486.35 mm O 494.34 mm What is the maximum measured extend (X) of the part when flattened? 12 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 Question of 15 For 10 points: B1001 - Create Sheet Metal Part From Solid Part Unit system: IPS (inch, pound, second) Decimal places: Part origin: Arbitrary Material = Already defined Sheet Metal Thickness: 0.125 inch Inner Bend Radius = 0.225 inch General K-Factor = 0.5 - Download the attached part NOTE: DO NOT modify any of the material properties of the part - Create a Sheet Metal part that will fit around the downloaded part using the following parameters: 13 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 Attachment to this question B.SLDPRT (153.5 kB) Enter Value: (use (point) as decimah separator) Sheet Metal Thickness: 0.125 inch Inner Radius: 0.225 inch Keep Body = OFF Gap For All Rips: 0.08 inch Overlap Ratio :0.50 Obround Relief Ratio: 0.50 Note 1: The sheet metal part should be OUTSIDE of the downloaded solid (Any small interferences between the sheet metal part and solid at the folded edges should be ignored.) Note 2: The bottom of the sheet metal part is open The Jinside of the part shown in the images is colored for clarity Your part will probably differ in color |- Measure the mass of the resulting Sheet Metal part What is the mass of the Sheet Metal part (pounds)? 14 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 15 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 Question of 15 Quote For 10 points: B2001 - Bounding Box Area Unit system: IPS (inch, pound, second) Decimal places: Part origin: Arbitrary Material = Already defined Sheet Metal Thickness: 0.125 inch Inner Bend Radius = 0.225 inch General K-Factor = 0.5 - Using the Sheet Metal part created in the previous question, measure the Bounding Box Area of the flattened Sheet Metal part What is the Bounding Box Area of the flattened Sheet Metal part (inches)? 244.54 271.44 255.19 301.25 16 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 Question 10 of 15 Q0.50 1.50 For 10 points: B3001 - Create Hem Unit system: IPS (inch, pound, second) Decimal places: Part origin: Arbitrary Material = Already defined Sheet Metal Thickness: 0.125 inch Inner Bend Radius = 0.225 inch General K-Factor = 0.5 - Create a hem on the Sheet Metal part using the following parameters: Hem Type: Open Length: 1.00 inch Gap Distance: 0.125 inch Custom Relief Type: Rectangular Relief Ratio: 0.50 -Measure the mass of the Sheet Metal part What is the mass of the Sheet Metal part (pounds)? Enter Value: I (use (point) as decimal separator) Question 11 of 15 17 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 For 10 points: C1001 - Cutting Length - Outer Unit system: IPS (inch, pound, second) Decimal places: Part origin: Arbitrary Material = Already defined Sheet Metal Thickness = Already defined Inner Bend Radius = Already defined General K-Factor = Already defined - Download and open the attached part file NOTE: DO NOT modify any of the material properties of the part - Using the Sheet Metal Cut List, measure the Outer Cutting Length of the flat pattern Attachment to this question 95.99 89.99 99.99 84.99 Question 12 of 15 For 10 points: 18 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 C2001 - Gauge Table Import Unit system: IPS (inch, pound, second) Decimal places: Part origin: Arbitrary Material = Already defined Sheet Metal Thickness = Already defined Inner Bend Radius = Already defined General K-Factor = Already defined - Download the attached Gauge Table - Using the downloaded Gauge Table, apply it to the sheet metal part downloaded in the previous question - Use the Gauge Table to apply the following parameters to the Sheet Metal part: Attachment to this question @ bend allowance inches sample - English.xls (27.0 kB) Enter Value: (use (point) as decimal separator) Question 13 of 15 QtQ 19 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 For 10 points: C3001 - Inner Bend Radius Modification Unit system: IPS (inch, pound, second) Decimal places: Part origin: Arbitrary Material = Already defined Sheet Metal Thickness = Already defined Inner Bend Radius = Already defined General K-Factor = Already defined - Using the applied Gauge Table from the previous question, modify the inner radius of the two bends circled in the image to the following value: Inner Radius: 0.5 inches (Gauge Table Value) - Measure the Bounding Box Length - What is the Bounding Box Length (inches)? Enter Value: (use (point) as decimal separator) Question 14 of 15 For 10 points: 20 Solidworks Sheet Metal ... mass of the resulting Sheet Metal part What is the mass of the Sheet Metal part (pounds)? 14 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 15 Solidworks Sheet Metal Nguyễn Phước Lợi... 190 mm C = 74 mm |-Measure the mass of the resulting Sheet Metal part What is the mass of the Sheet Metal part (grams)? 51.50 Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021 Enter Value:... Z |- Measure the mass of the resulting Sheet Metal part 45151.56 51.50 What is the mass of the Sheet Metal part (grams)? Enter Value: Solidworks Sheet Metal Nguyễn Phước Lợi November 18, 2021