Tài liệu Multiprotocol Skills LAB pptx

Multiprotocol Skills LAB NBMA Network (x.25 or Frame Relay) Ring 2 Ring 1 R1 R2 R3 R4 R5 Lab 1. Connect Terminal Server (1 hour) 1. Setup routers as shown in the diagram below: 2. Using a CS-500 or 2509-2511 connect an asynchronous serial port to the console port on each router. Configure a ip host list for a reverse telnet session into each router. Lab 2. IP (6 hours) • Configure the network using network 172.16.x.x • Use an 8 bit subnet mask unless otherwise specified At the end of each exercise, verify connectivity between all ports: • All ip routes appearing in all routers • Ping from any interface to any other interface Lab 2a 1. Connect R1, R2, and R3 over Frame Relay/X.25 (choose). Configure R3 using subinterfaces. Configure R1 without using subinterfaces and using map commands. Configure R2 without using subinterfaces or map commands. 2. Configure OSPF with the cloud in area 0. Configure R4, R5, and R3-R4 serial to be in area 1. 3. Configure two loopbacks on R1 using subnets that will contain at most 14 hosts ip addresses. Configure two loopbacks on R2 using subnets that will contain at most 62 hosts. Summarize the two loopback interfaces on R1 and R2 such that R3 only sees one route from each. Lab 2b 1. Remove OSPF configurations from R4, R5 and the serial connection between R3 and R4. Configure EIGRP on R4, R5 and on the serial connection between R3 and R4. Redistribute OSPF and EIGRP on R3. 2. Repeat step 1 using IGRP instead of EIGRP. Lab 2c 1. Remove IGRP from R3 and the serial link between R3 and R4. Create a BGP autonomous network between these routers. Redistribute and aggregate all routes. Lab 2d 1. Filter such that only R5 can ping the loopbacks on R2 but not the ethernet. The route for the ethernet should still be visible 2. Filter on R4 such that R1, R2, and R3 only see the routes from the token-ring interface on R5. Lab 2e 1. Remove filters from R4. 2. Configure R4 such that it advertises a default network to R5. R5 should be able to ping all interfaces. Lab III. Appletalk (1 hour) At the end of each exercise, verify connectivity between all ports: • All Apple routes/zones appearing in all routers • Apple ping from any interface to any other interface Lab 3a 1. Configure all ports (except loopbacks) for appletalk. Define a zone on each interface. Define the interface on R5 as Appletalk phase I. 2. Configure EIGRP for R3, R4, and R5. 3. Configure RTMP/ZIP for the NBMA network. Lab 3b 1. Filter on R4 such that R5 only sees routes and zones from R1. Lab 3c 1. Remove Appletalk from the serial network between R3 and R4. All zones and routes should still be seen by all routers running Appletalk Lab IV. DECnet (30 minutes) At the end of each exercise, verify connectivity between all ports • Appropriate DEC areas/nodes appearing in all routes • DEC ping from any router to any other router Lab 4a 1. Enable DECnet routing on all routers. Configure R4 and R5 in a separate DECnet area from the rest of the routers. Lab V. IPX (1 hour) At the end of each exercise, verify connectivity between all ports. • Appropriate IPX routes/SAP’s appearing in all routers • IPX ping from any interface to any other interface Lab 5a 1. Configure all ports (including loopbacks) for IPX. 2. ConfigureRIP/SAP on R4, R5, and the serial network between R3 and R4. 3. Configure only EIGRP on R1, R2, and R3’s NBMA network interface. 4. Redistribute on R3. Lab 5b 1. Configure two static SAPs on R5. Filter on R4 such that R1, R2, and R3 see only one of theSAPs. 2. Disable IPX across the NBMA network. All routes should still be seen by all routers running IPX 3. Change the frequency of RIP updates across the serial connection between R4 and R5 to once every 2 minutes. Lab VI. Dial-on-demand rounting (2 hours) At the end of each exercise, verify connectivity between all ports: • Ping all interfaces using applicable protocols Lab 6a 1. Configure either ISDN or an asynchronous connection between R3 and R4 2. Disconnect the serial link between R3 and R4 3. Configure dial-on-demand routing for IP and IPX between R3 and R4. No broadcast packets should initiate the dialing. Lab VII. DLSW (1 hour) Lab 8a 1. Configure DLSW between Ring1 and Ring 2. 2. Add R3’s ethernet into the DLSW network. Make sure there is connectivity between all lan interfaces. Lab 8b 1. Configure a filter that blocks Netbios packets with destination name “SERVER” from leaving Ring 1. 2. Set up a filter that would permit only SNA traffic between the token-rings. Lab VIII. HSRP (1 hours) 1. Connect 3 routers to an ethernet as shown below. 2. Define IP addresses on all interfaces. Configure a loopback interface on R3 and give it an IP address. 3. Setup any type of connections and any type of IP routing between R1, R2 and R3. 4. Disable IP routiing on the router named Host and configure it as an IP host 5. Configure HSRP between R1 and R2. 6. You should be able to disconnect the ethernet on either R1 or R2 and still be able to ping the loopback on R3 from Host. Host R1 R2 R3 . Multiprotocol Skills LAB NBMA Network (x.25 or Frame Relay) Ring 2 Ring 1 R1 R2 R3 R4 R5 Lab 1. Connect Terminal Server. Lab 2e 1. Remove filters from R4. 2. Configure R4 such that it advertises a default network to R5. R5 should be able to ping all interfaces. Lab