Hộp số tự động dana te2732 dùng trên xe nâng container dùng trên xe hàng Kalmar .terex hunter sanny sử dụng trong các cảng và bãi container.Hộp số tự động dana te2732 dùng trên xe nâng container dùng trên xe hàng Kalmar .terex hunter sanny sử dụng trong các cảng và bãi container
Service Manual Powershift Transmission TE27 & TE32 4-Speed Long Drop with Full Flow Control Valve 80-1070 Rev 5/12/2014 TSM-0064 August 2012 CONTENTS CONTENTS i Towing or Pushing Introduction Foreword Safety Precautions SPECIFICATIONS Third Speed Gear Group 69 Reverse/Second Clutch Shaft Group 71 First Shaft Group 73 Fourth Clutch Shaft Group 75 First Speed Gear Group 77 Identification Tag General Specifications Output Shaft Group 79 Regulator Valve Group 81 Control Valve Group 83 Hydraulic Cooler Lines Specifications Remote Filter Adapter Group Pressure and Temperature Specifications Electrical Specifications Maintenance Sump preheaters Filters Clutch Calibration Lubricants Servicing Machine After Component Overhaul Automatic Calibration Procedure Drive Plate Installation 12 Transmission to Engine Installation 13 EXTERNAL PLUMBING INSTALLATION 14 SPEED SENSOR INSTALLATION 15 TEMPERATURE SENSOR INSTALLATION 17 TRANSMISSION OPERATION 18 Converter, Pump Drive, & Pressure Regulating Valve 19 Input Shaft and Directional Clutches 20 Range Clutches 21 Transmission Controls 22 Electric Solenoid Controls 23 Power Flows, Activated Solenoids, & Hydraulic Circuits 24 Gear & Clutch Layout TROUBLESHOOTING 42 43 Transmission Problems 43 Troubleshooting Procedures 43 Troubleshooting Guide 46 Check Points 47 Checkports 50 Full Flow Valve Components 51 Speed Sensor Static Standalone Test 52 EXPLODED VIEWS 53 Converter Housing Group 53 Transmission Case & Rear Cover Group 55 Turbine Shaft Group 57 Charging Pump Drive Group 59 Torque Converter Assembly Group 61 Forward, Reverse/Second, & Third or Fourth Clutch Shaft Assembly 63 Forward Clutch Shaft Group 65 Third Clutch Shaft Group 67 85 Converter Housing Cover Group 87 Input Flange Group 89 Idler Shaft Gear Group 91 Idler Shaft Group 93 External Dipstick Group 95 INSTALLATION DIAGRAMS .97 Transmission Assembly Instructions Control Valve Assembly Instructions 97 102 Cleaning and Inspection 103 DISASSEMBLY & REASSEMBLY 104 Getting Started 104 Transmission Case Disassembly 104 Converter Housing Disassembly 120 Reverse & Second Clutch Disassembly 121 Reverse & Second Clutch Reassembly 124 Forward Clutch Disassembly 128 Forward Clutch Reassembly 131 Third Clutch Disassembly 134 Third Clutch Reassembly 136 Fourth Clutch Disassembly 138 Fourth Clutch Reassembly 140 First Clutch Disassembly 143 First Clutch Reassembly 145 Idler Shaft Disassembly 149 Idler Shaft Reassembly 150 Turbine Shaft Disassembly 150 Turbine Shaft Reassembly 151 Impeller Disassembly 152 Impeller Reassembly 153 Impeller Cover & Turbine Disassembly 155 Impeller Cover & Turbine Assembly 155 Converter Cover Disassembly 156 Converter Cover Reassembly 156 Pump Drive Gear Disassembly 156 Pump Drive Gear Reassembly 157 Converter Housing Reassembly 157 Transmission Case Reassembly 159 TORQUE SPECIFICATIONS 175 Lubricated or Plated Screws 175 Pipe Plugs 177 SPECIAL TOOLS TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual 178 Dana Holding Corporation i TOWING OR PUSHING Before towing the vehicle, be sure to lift the driven axle wheels off the ground or disconnect the driveline to avoid damage to the transmission during towing NOTE: Because of the design of the hydraulic system, the engine cannot be started by pushing or towing Dana Holding Corporation TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual INTRODUCTION Foreword This manual has been prepared to provide the customer and maintenance personnel with information and instructions on the maintenance and repair of Dana Spicer products Extreme care has been exercised in the design, selection of materials, and manufacturing of these units The slight outlay in personal attention and cost required to provide regular and proper lubrication, inspection at stated intervals, and adjustments as indicated will be reimbursed many times in low cost operation and trouble-free service In order to become familiar with the various parts of the product, its principle of operation, troubleshooting, and adjustments, it is urged that mechanics study the instructions in this manual carefully and use it as a reference when performing maintenance and repair operations Whenever repair or replacement of component parts is required, only Dana Spicer approved parts, as listed in the applicable service parts list, should be used Use of “will fit” or non-approved parts may endanger proper operation and performance of the equipment Dana does not warrant repair, replacement parts, or failures resulting from the use of parts which are not supplied or approved by Dana IMPORTANT: ALWAYS FURNISH THE DISTRIBUTOR WITH THE SERIAL AND MODEL NUMBER WHEN ORDERING PARTS Safety Precautions To reduce the chance of personal injury and/or property damage, the following instructions must be carefully observed Proper service and repair are important to the safety of the service technician and the safe, reliable operation of the machine If replacement parts are required, the part must be replaced with a Dana specified replacement part NEVER use a replacement part of lesser quality The service procedures recommended in this manual are effective methods of performing service and repair Some of these procedures require the use of unique tools Accordingly, anyone who intends to use a replacement part, service procedure, or tool, which is not recommended, must first determine that neither their safety or the safe operation of the machine will be jeopardized by the replacement part, service procedure, or tool selected It is important to note that this manual contains various precautions that must be carefully observed in order to reduce the risk of personal injury during service or repair Improper service or repair may also damage the unit or render it unsafe It is important to understand that these precautions are not exhaustive It is impossible to warn of all possible hazardous consequences that may result from following or failing to follow these instructions DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in moderate or minor injury NOTICE Indicates a situation which, if not avoided, may result in damage to components TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Dana Holding Corporation SPECIFICATIONS Identification Tag The nameplate contains both the model and serial number of the unit General Specifications * Weight (dry) 2204 lbs / 1000 kg Length (maximum) 39.8" / 1011 mm for T models 46.8" / 1189 mm for MT models Width (maximum) 27.7"/ 703 mm Height (maximum) 49.6"/ 1260 mm Oil Capacity 7.9 US gallons / 30 liters* Without cooler and hydraulic lines Consult equipment operator’s manual for complete system capacity Hydraulic Cooler Lines Specifications Lines and Fittings (Minimum) 1" / 25.4 mm internal diameter Continuous Operating Temperature Ambient to 248°F / 120°C Continuous Pressure 406 PSI / 28 bar continuous pressure and 595 PSI / 41 bar intermittent surges Conformance SAE J1019 and SAE J517, 100RI Dana Holding Corporation TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Pressure and Temperature Specifications Pressure and Temperature Specifications Normal Operating Temperature 158–248ºF / 70–120ºC Measured at temperature check port converter out (port 71 or port 32*) Maximum Temperature 248ºF / 120ºC Regulator Pressure† Vehicle in Neutral & Port 31* At 600 RPM minimum: 326.3 PSI / 22.5 bar minimum At 2650 RPM: 369.8 PSI / 25.5 bar maximum Pump Flow† At 1900RPM 31.5 GPM / 119.3 l/min minimum Lube Pump Flow At 2170 RPM selective lube 12.5 GPM / 47.2 l/min minimum Clutch Pressure† 1st clutch: Port 41* 2nd clutch: Port 42* 3rd clutch: Port 43* 4th clutch: Port 44* Forward clutch: Port 45* Reverse clutch: Port 46* At 2200 RPM: 297.3 PSI / 20.5 bar minimum with 1st clutch activated Filter Bypass Valve† Set at 59.4-65.2 PSI / 4.1-4.5 bar† Lube Pressure† Port 34 58–80 PSI / 4.0–5.5 bar at 2200 RPM Internal Total Leakage At 1000 engine RPM FWD/REV: GPM [4 l/min.] maximum 1st: 2.43 GPM [9.2 l/min.] maximum 2nd-3rd-4th: GPM [4 l/min.] maximum Converter: 1.3–3.2 GPM [5–12 l/min.] at 1000 RPM Safety Valve Cracking Pressure† 127.6–139.2 PSI / 8.8–9.6 bar Converter Out Pressure† Port 33 72.5 PSI / bar minimum 2000 RPM and maximum 123.3 PSI / 8.5 bar at no load governed speed * Refer to “TROUBLESHOOTING” for check port identification † All pressures and flows to be measured with oil temperature 180-200ºF / 82-93ºC TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Dana Holding Corporation Electrical Specifications Electrical Specifications Proportional Valves FWD/REV - 1st/3rd - 2nd/4th Coil Resistance: 7.25: at 68°F / 20°C Selection Valves FWD/N/REV - 1st/3rd Coil Resistance: 12V - 7.1: at 68°F / 20°C Coil Resistance: 24V - 28.5: at 68°F / 20°C Speed Sensor Type: Magneto resistive sensor Sensing Distance: 0–0.07"/ 0–1.8 mm Sensor Signal: Generates a square current with a fixed amplitude changing between and 14 mA Temperature Sensor Material: Silicon Resistance: 77°F / 25°C = 2000: + 1% Pressure Sensor Supply Voltage: 4.5-5.5V Maximum Current: 10mA Pressure Range: 14.5-450 PSI / 1-31 bar + 1.2% full scale (450 PSI / 31 bar) range 14.5-363 PSI / 1-25 bar + 2.5% full scale (450 PSI / 31 bar) range 363-450 PSI / 25-31 bar Dana Holding Corporation TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual MAINTENANCE Sump preheaters Preheat the transmission fluid to the minimum temperature for the oil viscosity used before engine start up Filters Service oil filter elements the first time at 100 hours and then every 1000 hours under normal environmental and duty cycle conditions Clutch Calibration Perform automatic clutch calibration every 2000 hours Lubricants Recommended Lubricants Only Dextron® III is approved Viscosity at 104°F [40°C] = 33 - 38 cSt; at 212°F [100°C] = 7-8 cSt Maintenance Intervals Daily Check oil level daily with engine running at idle (600 RPM) and oil at 180-200°F [82 - 93°C] Maintain oil level at full mark Normal oil change interval Drain and refill system every 1000 hours for average environmental and duty cycle conditions Severe or sustained high operating temperature or very dusty atmospheric conditions will result in accelerated deterioration or contamination Judgement must be used to determine the required change intervals for extreme conditions Every 1000 hours: • Change oil filter element • Drain oil at 150–200°F [65-93°C] and refill system as follows: Drain transmission Remove and discard filter Install new filter Refill transmission to FULL mark Run engine at 500 - 600 RPM to prime converter and lines Recheck level with engine running at 500 - 600 RPM and add oil to bring level to LOW mark When oil temperature is hot 180-200°F [82.2-93.3°C] make final oil level check and adjust if necessary to bring oil level to FULL mark NOTE: It is recommended that oil filter be changed after 100 hours of operation on new, rebuilt, or repaired unit Extended oil change interval Extended oil service life may result when using synthetic fluids Appropriate change intervals should be determined for each transmission by measuring oil oxidation and wear metals, over time, to determine a baseline Wear metal analysis can provide useful information but a transmission should not be removed from service based solely on this analysis TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Dana Holding Corporation Servicing Machine After Component Overhaul Servicing Machine After Component Overhaul The transmission, torque converter, and its allied hydraulic system are important links in the driveline between the engine and the wheels The proper operation of either unit depends greatly on the condition and operation of the other Therefore, whenever repair or overhaul of one unit is performed, the balance of the system must be considered before the job can be considered complete After the overhauled or repaired transmission has been installed in the machine, the oil cooler, and connecting hydraulic system must be thoroughly cleaned This can be accomplished in several manners and a degree of judgement must be exercised as to the method employed The following are considered the minimum steps to be taken: Drain entire system thoroughly Disconnect and clean all hydraulic lines Where feasible hydraulic lines should be removed from machine for cleaning Replace oil filter element The oil cooler must be thoroughly cleaned The cooler should be “back flushed” with oil and compressed air until all foreign material has been removed Flushing in direction of normal oil flow will not adequately clean the cooler If necessary, cooler assembly should be removed from machine for cleaning, using oil, compressed air, and steam cleaner for that purpose IMPORTANT: NEVER use flushing compounds for cleaning purposes Reassemble all components and use only type oil (See chapter 4.1.1 “Recommended lubricants”) Fill the transmission through filler opening until fluid comes up to FULL mark on transmission dipstick • Remove filler plug and fill oil until FULL mark • Run engine two minutes at 500 - 600 RPM to prime torque converter and hydraulic lines • Recheck level of fluid in transmission with engine running at idle (500 - 600 RPM) • Add quantity necessary to bring fluid level to LOW mark on dipstick • Recheck with hot oil 180 – 200°F [82.2 - 93.3°C] • Adjust oil level to FULL mark on dipstick Recheck all drain plugs, lines, connections, etc… for leaks and tighten where necessary Perform automatic calibration Dana Holding Corporation TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Transmission Case Reassembly FIGURE 388: Install 4th clutch hub and snap ring FIGURE 391: Install new converter-housing-to-transmissioncase gasket and new o-rings (3) WARNING Use caution when installing snap ring Failure to comply can cause personal injury FIGURE 392: Install alignment studs and position converter housing assembly onto studs Install converter-housing-totransmission-housing bolts and lockwashers and tighten to specified torque Refer to “TORQUE SPECIFICATIONS” on page 175 NOTE: Turning output shaft will assist in aligning clutch hubs with clutch assembly FIGURE 389: Install 2nd clutch hub CAUTION CAUTION NEVER use bolts to pull converter and transmission housing together Failure to comply may cause equipment damage FIGURE 390: Install 2nd clutch hub snap ring, spacer, and snap ring WARNING Use caution when installing snap ring Failure to comply can cause personal injury FIGURE 393: Install aligning studs and install new valve gasket 169 Dana Holding Corporation TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Transmission Case Reassembly FIGURE 394: Install control valve and tighten capscrews to specified torque (refer to “TORQUE SPECIFICATIONS” on page 175), following the sequence outlined in the “Transmission Assembly Instructions” on page 97 of the manual FIGURE 397: Install pump drive shaft FIGURE 398: With new o-ring in place, install hydraulic pump assembly FIGURE 395: Install regulator valve and new valve-to-converterhousing gasket to converter housing FIGURE 399: Install hydraulic pump capscrews and lockwashers and tighten to specified torque Refer to “TORQUE SPECIFICATIONS” on page 175 FIGURE 396: Install capscrews and tighten to specified torque Refer to “TORQUE SPECIFICATIONS” on page 175 TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Dana Holding Corporation 170 Transmission Case Reassembly FIGURE 400: Install adapter / suction hose assembly to hydraulic pump assembly, fitting new o-rings if required FIGURE 401: Install capscrews and lockwashers and tighten to specified torque Refer to “TORQUE SPECIFICATIONS” on page 175 FIGURE 403: Install hydraulic pump drive shipping covers (if fitted) and install bolts and lockwashers Tighten to specified torque Refer to “TORQUE SPECIFICATIONS” on page 175 FIGURE 404: Install impeller assembly FIGURE 405: Install impeller hub bearing inner race FIGURE 402: Tighten clamps on suction hose 171 Dana Holding Corporation TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Transmission Case Reassembly FIGURE 406: Install reaction member spacer FIGURE 409: Install turbine hub rear snap ring on shaft WARNING Use caution when installing snap ring Failure to comply can cause personal injury FIGURE 407: Install reaction member with thin side of blades inward to impeller FIGURE 410: Position new o-ring on impeller cover and install cover and turbine assembly on shaft FIGURE 408: Install reaction member snap ring WARNING Use caution when installing snap ring Failure to comply can cause personal injury FIGURE 411: Install impeller cover screws and lockwashers and tighten to specified torque Refer to “TORQUE SPECIFICATIONS” on page 175 TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Dana Holding Corporation 172 Transmission Case Reassembly FIGURE 412: Install turbine snap ring FIGURE 415: Warm input shaft support bearing to 248°F [120°C] and install on input shaft WARNING Use caution when installing snap ring Failure to comply can cause personal injury FIGURE 416: Install converter housing front cover with Loctite 515 FIGURE 413: Install input shaft support with new o-ring FIGURE 417: Install bolts and washers and tighten to specified torque Refer to “TORQUE SPECIFICATIONS” on page 175 FIGURE 414: Install bolts and tighten to specified torque Refer to “TORQUE SPECIFICATIONS” on page 175 173 Dana Holding Corporation TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Transmission Case Reassembly FIGURE 418: Install input flange FIGURE 421: Install speed sensors (3) FIGURE 419: Install input flange o-ring, washer, and nut FIGURE 422: Install temperature sensor FIGURE 420: Tighten nut to specified torque Refer to “TORQUE SPECIFICATIONS” on page 175 TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Dana Holding Corporation 174 TORQUE SPECIFICATIONS Lubricated or Plated Screws COARSE PITCH TYPE OF BOLT SIZE OF BOLT Grade Grade lbs ft N•m lbs ft N•m 2500 - 10 10.8 - 13.6 - 11 12.2 - 14.9 3125 12 - 16 16.3 - 21.7 26 - 30 35.2 - 40.7 3750 23 - 25 31.2 - 33.9 33 - 36 44.7 - 48.8 4375 37 - 41 50.2 - 55.6 52 - 57 70.5 - 77.3 5000 57 - 63 77 - 85 80 - 88 108 - 119 5625 82 - 90 111 - 122 115 - 127 156 - 172 6250 113 - 124 153 - 168 159 - 175 216 - 237 7500 200 - 220 271 - 298 282 - 310 382 - 420 FINE PITCH TYPE OF BOLT SIZE OF BOLT 175 Grade Grade lbs ft N•m lbs ft N•m 2500 - 11 12.2 - 14.9 11 - 13 14.9 - 17.6 3125 16 - 20 21.7 - 27.1 28 - 32 38.0 - 43.4 3750 26 - 29 35.2 - 39.3 37 - 41 50.2 - 55.6 4375 41 - 45 56 - 61 58 - 64 79 - 87 5000 64 - 70 87 - 95 90 - 99 122 - 134 5625 91 - 100 123 - 136 128 - 141 174 - 191 6250 129 - 141 174 - 191 180 - 198 224 - 268 7500 223 - 245 302 - 332 315 - 347 427 - 470 Dana Holding Corporation TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Lubricated or Plated Screws COARSE PITCH TYPE OF BOLT SIZE OF BOLT Grade 8.8 Grade 10.9 Grade 12.9 lbs ft N•m lbs ft N•m lbs ft N•m M5 x 0.8 3.7 - 4.4 5-6 5.2 - 5.9 7-8 5.9 - 7.4 - 10 M6 x 5.9 - 7.4 - 10 8.9 - 11.1 12 - 15 9.6 - 11.8 13 - 16 M8 x 1.25 14.8 - 18.4 20 - 25 22.1 - 25.8 30 - 35 25.8 - 29.5 35 - 40 M10 x 1.5 29.5 - 36.9 40 - 50 44.3 - 47.9 60 - 65 47.9 - 55.3 65 - 75 M12 x 1.75 50 - 55 68 - 75 74 - 81 100 - 110 85 - 96 115 - 130 M14 x 81 - 92 110 - 125 111 - 129 150 - 175 133 - 155 180 - 210 M16 x 125 - 140 170 - 190 177 - 203 240 - 275 207 - 236 280 - 320 M20 x 2.5 236 - 266 320 - 360 332 - 369 450 - 500 387 - 443 525 - 600 M24 x 420 - 479 570 - 650 590 - 664 800 - 900 664 - 774 900 - 1050 M30 x 3.5 848 - 959 1150 - 1300 1180 - 1328 1600 - 1800 1364 - 1549 1850 - 2100 M36 x 1475 - 1660 2000 - 2250 2028 - 2323 2749 - 3149 2397 - 2729 3249 - 3699 FINE PITCH TYPE OF BOLT SIZE OF BOLT Grade 8.8 Grade 10.9 Grade 12.9 lbs ft N•m lbs ft N•m lbs ft N•m M8 x 17 - 20 23 - 28 25 - 28 34 - 39 30 - 34 41 - 46 M10 X 35 - 42 47 - 57 52 - 60 71 - 81 62 - 69 84 - 94 M10 x 1,25 32 - 40 44 - 54 49 - 57 67 - 77 58 - 66 79 - 89 M12 x 1,25 60 - 68 82 - 92 89 - 96 120 - 130 105 - 116 143 - 158 M12 x 1,5 58 - 65 78 - 88 86 - 94 117 - 127 101 - 112 138 - 153 M14 x 1,5 94 - 105 128 - 143 142 - 153 193 - 208 162 - 184 220 - 250 M16 x 1,5 159 - 169 215 - 228 216 - 227 293 - 308 258 - 273 350 - 370 M18 x 1,5 221 - 236 300 - 320 319 - 330 433 - 448 369 - 398 500 - 540 M18 x 207 - 221 280 - 300 304 - 315 413 - 428 347 - 376 470 - 510 M20 x 1,5 302 - 332 410 - 450 439 - 476 595 - 645 503 - 559 683 - 758 M22 x 1,5 413 - 443 560 - 600 586 - 623 795 - 845 681 - 736 923 - 998 M24 x 1,5 531 - 590 720 - 800 767 - 841 1040 - 1140 882 - 992 1195 - 1345 M24 x 509 - 568 690 - 770 730 - 804 990 - 1090 845 - 955 1145 - 1295 M27 x 1,5 789 - 848 1070 - 1150 1129 - 1202 1530 - 1630 1308 - 1420 1175 - 1925 TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Dana Holding Corporation 176 Pipe Plugs Pipe Plugs 177 THREAD SIZE lbs ft N•m M10 x 6-7 - 10 M14 x 1.5 7-9 10 - 12 M18 x 1.5 25 - 30 34 - 41 M22 x 1.5 35 - 44 48 - 60 M26 x 1.5 45 - 50 61 - 68 M33 x 83 - 103 112 - 140 THREAD SIZE lbs ft N•m 1/16 - 27 5-7 7-9 1/8 - 27 - 10 - 14 1/4 - 18 15 -20 20 - 27 5/16 - 24 3-5 4-7 3/8 - 24 5-8 - 11 3/8 - 18 25 - 30 34 - 41 1/2 - 14 30 - 35 41 - 47 1/2 - 20 10 - 13 14 - 18 3/4 - 10 40 - 45 54 - 61 3/4 - 14 40 - 45 54 - 61 7/16 - 20 - 10 - 14 9/16 - 18 12 - 15 16 - 20 3/4 - 16 20 - 25 27 - 34 7/8 - 14 30 - 35 41 - 47 11/16 - 12 45 - 50 61 - 68 15/16 - 12 65 - 75 88 - 102 - 11-1/2 50 - 55 68 - 75 1-1/4 - 11-1/2 60 - 65 81 - 88 1-5/8 - 12 75 - 85 102 - 115 1-7/8 - 12 75 - 85 102 - 115 Dana Holding Corporation TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual SPECIAL TOOLS Idler & Low Shaft Lifting Hook Bolt M10 x 40 TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Eyebolt M16 Dana Holding Corporation 178 Impeller Cover Lifting Hook Impeller Cover Lifting Hook Bolt 4375-14 UNC-3B X 20 both sides 179 Dana Holding Corporation TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Shaft Nut Socket Shaft Nut Socket TYP TYP TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Dana Holding Corporation 180 4th Drum Lifting Hook 4th Drum Lifting Hook 181 Dana Holding Corporation TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual 2nd/Rev Drum Lifting Hook 2nd/Rev Drum Lifting Hook TSM-0064 - TE27/32 4-Speed LD with Full Flow Control Valve Service Manual Dana Holding Corporation 182 Copyright 2012 Dana Holding Corporation All content is subject to copyright by Dana and may not be reproduced in whole or in part by any means, electronic or otherwise, without prior written approval THIS INFORMATION IS NOT INTENDED FOR SALE OR RESALE, AND THIS NOTICE MUST REMAIN ON ALL COPIES For product inquiries or support, visit www.dana.com or call 419-887-6445 For other service publications, visit www.SpicerParts.com/literature.asp For online service parts ordering, visit www.SpicerParts.com/order.asp ... the sensor! 15 Dana Holding Corporation TSM-0064 - TE27/ 32 4-Speed LD with Full Flow Control Valve Service Manual Speed Sensor Installation Speed Sensor Installation TSM-0064 - TE27/ 32 4-Speed... LD with Full Flow Control Valve Service Manual Dana Holding Corporation 16 TEMPERATURE SENSOR INSTALLATION 17 Dana Holding Corporation TSM-0064 - TE27/ 32 4-Speed LD with Full Flow Control Valve... 1st/3rd FWD/REV, 1st/3rd Reverse, 1st Dana Holding Corporation TSM-0064 - TE27/ 32 4-Speed LD with Full Flow Control Valve Service Manual HOSE HOSE TSM-0064 - TE27/ 32 4-Speed LD with Full Flow Control