Controlling Network Access and Use

CHAPTER 3-1 Cisco PIX Firewall and VPN Configuration Guide 78-13943-01 3 Controlling Network Access and Use This chapter describes how to establish and control network connectivity for different applications and implementations after you have completed your basic configuration, described in Chapter 2, “Establishing Connectivity.” This chapter contains the following sections: • Allowing Server Access with Static NAT • Allowing Inbound Connections • Controlling Outbound Connectivity • Using the Static Command for Port Redirection • Using Authentication and Authorization • Access Control Configuration Example • Using TurboACL • Downloading Access Lists • Simplifying Access Control with Object Grouping • Filtering Outbound Connections Allowing Server Access with Static NAT Static Network Address Translation (NAT) creates a permanent, one-to-one mapping between an address on an internal network (a higher security level interface) and a perimeter or external network (lower security level interface). For example, to share a web server on a perimeter interface with users on the public Internet, use static address translation to map the server’s actual address to a registered IP address. Static address translation hides the actual address of the server from users on the less secure interface, making casual access by unauthorized users less likely. Unlike NAT or PAT, it requires a dedicated address on the outside network for each host, so it does not save registered IP addresses. If you use a static command to allow inbound connections to a fixed IP address, use the access-list and access-group commands to create an access list and to bind it to the appropriate interface. For more information, refer to “Allowing Inbound Connections.” Note Do not use the PIX Firewall interface address with the static command if Stateful Failover is enabled. Doing this will prevent Stateful Failover from receiving its interface monitoring probes, which run over IP protocol 105, and as a result, the interface will appear to be in waiting state. For further information about Stateful Failover, refer to Chapter 10, “Using PIX Firewall Failover.” 3-2 Cisco PIX Firewall and VPN Configuration Guide 78-13943-01 Chapter 3 Controlling Network Access and Use Allowing Inbound Connections The main options of the static command are as follows: static [( internal_if_name , external_if_name )] global_ip local_ip [netmask network_mask ] [ max_conns ] • Replace internal_if_name with the internal network interface name. In general, this is the higher security level interface you are accessing. • Replace external_if_name with the external network interface name. In general, this is the lower security level interface you are accessing. • Replace global_ip with the outside (global) IP address. In general, this is the interface with the lower security level. This address cannot be a PAT IP address. • Replace local_ip with the internal (local) IP address from the inside network. In general, this is the interface with the higher security level. • Replace network_mask with the network mask pertains to both global_ip and local_ip. For host addresses, always use 255.255.255.255. For network addresses, use the appropriate subnet mask for the network. • (Optional) replace max_conns with the maximum number of concurrent connections permitted through the static address translation. Note To configure static translation for a host residing on the less secure interface (using outside NAT) reverse the interface in the static command. Refer to the Cisco PIX Firewall Command Reference for more information about the static command. For example, the following command maps a server with an internal IP address of 10.1.1.3 to the registered IP address 209.165.201.12: static (inside, outside) 209.165.201.12 10.1.1.3 netmask 255.255.255.255 0 0 This command simply maps the addresses; make sure you also configure access using the access-list and access-group commands, as described in the next section. Also, you will must inform the DNS administrator to create an MX record for the external address so that traffic sent to the server host name is directed to the correct address. Note For information about how to configure static translation without NAT, refer to the static command in the Cisco PIX Firewall Command Reference. Allowing Inbound Connections By default, the PIX Firewall denies access to an internal or perimeter (more secure) network from an external (less secure) network. You specifically allow inbound connections by using access lists. Access lists work on a first-match basis, so for inbound access, you must deny first and then permit after. Note Beginning with PIX Firewall version 5.3, access lists are the preferred method for managing network access. The conduit command was used in earlier versions. Access lists provide improved flexibility and greater ease of use for those familiar with Cisco IOS access control. However, the conduit command is still supported to maintain backward compatibility of configurations written for previous PIX Firewall versions. 3-3 Cisco PIX Firewall and VPN Configuration Guide 78-13943-01 Chapter 3 Controlling Network Access and Use Allowing Inbound Connections You use the access-list and access-group commands to permit access based on source or destination IP address, or by the protocol port number. Use the access-list command to create a single access list entry, and use the access-group command to bind one or more access list entries to a specific interface. Only specify one access-group command for each interface. Note To allow access only for specific users, set up authentication, as described in “Using Authentication and Authorization.” Before you can set up an access list for a host, set up address translation by using a global or static command. Setting up address translation with the global command is described in Chapter 2, “Establishing Connectivity.” Setting up address translation using the static command was described earlier in the previous section “Allowing Server Access with Static NAT.” The format for the access-list command is as follows: access-list ID action protocol source_address port destination_address port • Replace ID with a name or number you create to identify a group of access-list command statements; for example, “acl_out,” which identifies that the permissions apply to access from the outside interface. • Replace action with permit or deny depending on whether you want to permit or deny access to the server. By default, all inbound access is denied, so you will must permit access to a specific protocol or port. • Replace protocol with the protocol (tcp or udp). For most servers, such as HTTP or email, use tcp. • Replace source_address with the host or network address for those systems on the lower security level interface that must access the destination_address. Use any to let any host access the destination_address. If you specify a single host, precede the address with host; for example host 192.168.1.2 . If you specify a network address, also specify a network mask; for example, 192.168.1.0 255.255.255.0 . • Replace the first port parameter with the protocol port used by the source host to initiate the connection. • Replace destination_address with the host or network global address that you specified with the static command statement. For a host address, precede the address with host; for networks, specify the network address and the appropriate network mask. • Replace the second port parameter with the literal port name or number for the destination server protocol. For a web server, use the string http or the number 80. For an email server, use smtp or the number 25. The port is preceded with the eq (equals) parameter. The following is a list of literal port names that you can use when configuring an access-list command statement: DNS, ESP, FTP, H323, HTTP, IDENT, NNTP, NTP, POP2, POP3, PPTP, RPC, SMTP, SNMP, SNMPTRAP, SQLNET, TCP, Telnet, TFTP, and UDP. You can also specify these ports by number. Port numbers are defined in RFC 1700. Two access-list command statement definitions are required to permit access to the following ports: – DNS, Discard, Echo, Ident, NTP, RPC, SUNRPC, and Talk each require one definition for TCP and one for UDP. – PPTP requires one definition for port 1723 on TCP and another for port 0 and GRE protocol. – TACACS+ requires one definition for port 49 on TCP. The format for the access-group command is as follows: access-group ID in interface low_interface 3-4 Cisco PIX Firewall and VPN Configuration Guide 78-13943-01 Chapter 3 Controlling Network Access and Use Controlling Outbound Connectivity Replace ID with the same identifier that you specified in the access-list command statement. Replace low_interface with the lower security interface that you specified in the static command statement. This is the interface through which users will access the external (global) address. The following example illustrates the three commands required to enable access to a web server with the external IP address 209.165.201.12: static (inside, outside) 209.165.201.12 10.1.1.3 netmask 255.255.255.255 0 0 access-list acl_out permit tcp any host 209.165.201.12 eq www access-group acl_out in interface outside This example uses the same static command that was shown in the previous section. Controlling Outbound Connectivity By default, all connections initiated on a network with a higher security level are allowed out, and you configure any restrictions required. You can control outbound access by IP address and protocol port, or combine access control with user authentication, as described in “Using Authentication and Authorization.” If you are not enforcing restrictions on outbound network traffic, you do not need outbound access lists. An outbound access list lets you restrict users from starting outbound connections or lets you restrict users from accessing specific destination addresses or networks. Access lists work on a first-match basis, so for outbound access lists, you must permit first and then deny after. For example, you could restrict some users from accessing websites, permit others access, or restrict one or more users from accessing a specific website. Define access restrictions with the access-list command, and use the access-group command to bind the access-list command statements to an interface. When creating an outbound access list, the format for the access-list command statement is the same as shown earlier in “Allowing Inbound Connections:” access-list ID action protocol source_address port destination_address port By default, outbound access is permitted, so you use the deny action to restrict access when using an outbound access list. For example, to prevent users on the 192.168.1.0 network on the inside interface from starting connections on the outside interface and permit all others, specify the 192.168.1.0 network address as the source address and the network connected to the outside interface as the destination address. In the example that follows, the network on the outside interface is 209.165.201.0. The access-list and access-group command statements are as follows. access-list acl_in deny tcp 192.168.1.0 255.255.255.224 209.165.201.0 255.255.255.224 access-list acl_in permit ip any any access-group acl_in in interface inside You can use also use access lists to prevent access to a specific server. For example, if you want to restrict users on the inside interface from accessing a website at address 209.165.201.29 on the outside interface (while allowing other outbound access), use the following commands: access-list acl_in deny tcp any host 209.165.201.29 eq www access-list acl_in permit ip any any access-group acl_in in interface inside These commands let any users start connections, but not to 209.165.201.29. The access-group command specifies that the users are on the inside interface. 3-5 Cisco PIX Firewall and VPN Configuration Guide 78-13943-01 Chapter 3 Controlling Network Access and Use Using the Static Command for Port Redirection Note If controlling outbound access in your network is an important issue, consider using the Websense filtering application, described in “Filtering URLs with Internet Filtering Servers.” Using the Static Command for Port Redirection This section describes the port redirection feature, introduced in PIX Firewall version 6.0. It includes the following topics: • Overview • Port Redirection Configuration • Port Redirection Example Overview Port redirection allows users on a lower security interface to connect to a particular IP address and port and to have the PIX Firewall redirect the traffic to the appropriate server on a higher security interface. The shared address can be a unique address, a shared outbound PAT address, or an address shared with the external interface. To implement port redirection, use the following command. static [( internal_if_name , external_if_name )] {tcp|udp} { global_ip |interface} global_port local_ip local_port [netmask mask ] For an explanation of this command syntax, refer to the Cisco PIX Firewall Command Reference. Port Redirection Configuration Figure 3-1 illustrates a typical network scenario in which the port redirection feature might be useful. Figure 3-1 Port Redirection Using the Static Command In the configuration described in this section, port redirection occurs for users on external networks as follows: • Telnet requests to unique IP address 209.165.201.5 are redirected to 10.1.1.6 • FTP requests to unique IP address 209.165.201.5 are redirected to 10.1.1.3 • Telnet requests to PAT address 209.165.201.15 are redirected to 10.1.1.4 10.1.1.2 209.165.201.25 PAT address = 209.165.201.15 Inside Outside 73601 3-6 Cisco PIX Firewall and VPN Configuration Guide 78-13943-01 Chapter 3 Controlling Network Access and Use Using the Static Command for Port Redirection • Telnet requests to the PIX Firewall outside IP address 209.165.201.25 are redirected to 10.1.1.5 • HTTP request to PIX Firewall outside IP address 209.165.201.25 are redirected to 10.1.1.5 • HTTP port 8080 requests to PAT address 209.165.201.15 are redirected to 10.1.1.7 port 80 To implement this scenario, complete the following steps: Step 1 Configure application inspection of FTP requests on port 21 by entering the following command: fixup protocol ftp 21 Step 2 Configure the IP address of the lower and higher security interfaces of your PIX Firewall by entering the following command: ip address outside 209.165.201.25 255.255.255.0 ip address inside 10.1.1.2 255.255.255.0 Step 3 Identify a global PAT address for the lower security interface by entering the following command: global (outside) 1 209.165.201.15 Step 4 Configure NAT and PAT by entering the following command: nat (inside) 1 0.0.0.0 0.0.0.0 0 0 Step 5 Redirect Telnet requests for 209.165.201.5: static (inside,outside) tcp 209.165.201.5 telnet 10.1.1.6 telnet netmask 255.255.255.255 0 0 This command causes Telnet requests to be redirected to 10.1.1.6. Step 6 Redirect FTP requests for IP address 209.165.201.5: static (inside,outside) tcp 209.165.201.5 ftp 10.1.1.3 ftp netmask 255.255.255.255 0 0 This command causes FTP requests to be redirected to 10.1.1.3. Step 7 Redirect Telnet requests for PAT address 209.165.201.15: static (inside,outside) tcp 209.165.201.15 telnet 10.1.1.4 telnet netmask 255.255.255.255 0 0 This command causes Telnet requests to be redirected to 10.1.1.4. Step 8 Redirect Telnet requests for the PIX Firewall outside interface address: static (inside,outside) tcp interface telnet 10.1.1.5 telnet netmask 255.255.255.255 0 0 This command causes Telnet requests to be redirected to 10.1.1.5. Step 9 Redirect HTTP requests for the PIX Firewall outside interface address: static (inside,outside) tcp interface www 10.1.1.5 www netmask 255.255.255.255 0 0 This command causes HTTP request to be redirected to 10.1.1.5. Step 10 Redirect HTTP requests on port 8080 for PAT address 209.165.201.15: static (inside,outside) tcp 209.165.201.15 8080 10.1.1.7 www netmask 255.255.255.255 0 0 This command causes HTTP port 8080 requests to be redirected to 10.1.1.7 port 80. 3-7 Cisco PIX Firewall and VPN Configuration Guide 78-13943-01 Chapter 3 Controlling Network Access and Use Using Authentication and Authorization Port Redirection Example Example 3-1 illustrates the configuration required to implement the port redirection described in this scenario. Example 3-1 Port Redirection with the static Command fixup protocol ftp 21 ip address outside 209.165.201.25 255.255.255.0 ip address inside 10.1.1.2 255.255.255.0 global (outside) 1 209.165.201.15 nat (inside) 1 0.0.0.0 0.0.0.0 0 0 static (inside,outside) tcp 209.165.201.5 telnet 10.1.1.6 telnet netmask 255.255.255.255 0 0 static (inside,outside) tcp 209.165.201.5 ftp 10.1.1.3 ftp netmask 255.255.255.255 0 0 static (inside,outside) tcp 209.165.201.15 telnet 10.1.1.4 telnet netmask 255.255.255.255 0 0 static (inside,outside) tcp interface telnet 10.1.1.5 telnet netmask 255.255.255.255 0 0 static (inside,outside) tcp interface www 10.1.1.5 www netmask 255.255.255.255 0 0 static (inside,outside) tcp 209.165.201.15 8080 10.1.1.7 www netmask 255.255.255.255 0 0 Using Authentication and Authorization You can use access lists to control traffic based on IP address and protocol, but to control access and use for specific users or groups, you must use authentication and authorization. Authentication, which is the process of identifying users, is supported by the PIX Firewall for RADIUS and TACACS+ servers. Authorization identifies the specific permissions for a given user. If you want to apply authentication and authorization when an internal (local) host initiates a connection to an external (lower security) network, enable it on the internal (higher security) interface. To set up authentication and authorization to occur when an external host initiates a connection to an internal host, enable it on the outside interface. Note If you want a host on an outside (lower security level) interface to initiate connections with a host on an internal (higher security level) interface, create static and access-list command statements for the connection. This section includes the following topics: • Configuring AAA • Configuring RADIUS Authorization Configuring AAA To enable authentication and authorization, identify the authentication server you are using and the server encryption key on the PIX Firewall. From the configuration on the authentication server you must determine the users that can access the network, the services that they can use, and the hosts that they can access. Once you have this information, you can configure the PIX Firewall to either enable or disable authentication or authorization. 3-8 Cisco PIX Firewall and VPN Configuration Guide 78-13943-01 Chapter 3 Controlling Network Access and Use Using Authentication and Authorization In addition, you can configure the PIX Firewall to control user access to specific hosts or services. However, it is easier to maintain this kind of access control in a single location, at the authentication server. After you enable authentication and authorization, the PIX Firewall provides prompts inbound or outbound for users of FTP, Telnet, or HTTP (Web) access. Controlling access to a specific system or service is handled by the authentication and authorization server. Follow these steps to enable the PIX Firewall to support TACACS+ user authentication and authorization: Step 1 For inbound authentication, create the static and access-list command statements required to permit outside hosts to access servers on the inside network. Step 2 If the internal network connects to the Internet, create a global address pool of registered IP addresses. Then specify the inside hosts that can start outbound connections with the nat command and with the access control lists features found in the outbound and apply commands. Step 3 Identify the server that handles authentication or authorization using the aaa-server command. Create a unique server group name. For example: aaa-server AuthInbound protocol tacacs+ aaa-server AuthInbound (inside) host 10.1.1.1 TheUauthKey aaa-server AuthOutbound protocol tacacs+ aaa-server AuthOutbound (inside) host 10.1.1.2 TheUauthKey The first command statement creates the AuthInbound authentication group using TACACS+ authentication. The second command statement states that the AuthInbound server is on the inside interface, that its IP address is 10.1.1.1, and the encryption key is “TheUauthKey.” The third command statement creates the AuthOutbound authentication group using TACACS+ authentication. The fourth command statement states that the AuthOutbound server is on the inside interface, that its IP address is 10.1.1.2, and the encryption key is “TheUauthKey.” Note RADIUS authorization is provided with the access-list command statement as described in “Configuring RADIUS Authorization.” Step 4 Enable authentication with the aaa authentication command: aaa authentication include ftp outbound 0 0 0 0 AuthOutbound aaa authentication include telnet outbound 0 0 0 0 AuthOutbound aaa authentication include http outbound 0 0 0 0 AuthOutbound aaa authentication include ftp inbound 0 0 0 0 AuthInbound aaa authentication include telnet inbound 0 0 0 0 AuthInbound aaa authentication include http inbound 0 0 0 0 AuthInbound The AuthInbound and AuthOutbound groups are those you specified with the aaa-server command. Note Be careful to apply authentication only to protocols that can be authenticated. Applying authentication using the any keyword will prevent protocols such as SMTP or HTTPS from passing through the PIX Firewall. 3-9 Cisco PIX Firewall and VPN Configuration Guide 78-13943-01 Chapter 3 Controlling Network Access and Use Using Authentication and Authorization Step 5 Enable authorization with the aaa authorization command. PIX Firewall checks the authorization request with the AAA server, which makes the decision about what services a user can access. Use one or both of the following commands to specify outbound and inbound authorization. aaa authorization include ftp outbound 0 0 0 0 aaa authorization include telnet outbound 0 0 0 0 aaa authorization include http outbound 0 0 0 0 aaa authorization include ftp inbound 0 0 0 0 aaa authorization include telnet inbound 0 0 0 0 aaa authorization include http inbound 0 0 0 0 You can specify port ranges for the aaa authorization command in the following format: aaa authorization include | exclude author_service inbound | outbound | if_name local_ip local_mask foreign_ip foreign_mask where: • author_service—The service that PIX Firewall listens to for AAA connections. Possible values are any, http, ftp, telnet, or protocol/port. Use the IP protocol number for protocol or use the TCP/UDP destination port or port range. A port value of 0 means all ports. You can also use a specific ICMP type. • inbound, outbound, if_name—Specify whether users are authenticated and authorized on inbound or outbound connections, or for connections that arrive at a specific interface. • local_ip, local_mask—Specify the IP address on the higher security level interface from which or to which access is required. • foreign_ip, foreign_mask—Specify the IP address on the lower security level interface from which or to which access is required. Configuring RADIUS Authorization PIX Firewall allows a RADIUS server to send user group attributes to the PIX Firewall in the RADIUS authentication response message. The administrator first defines access lists on the PIX Firewall for each user group. For example, there could be access lists for each department in an organization, sales, marketing, engineering, and so on. The administrator then lists the access list in the group profile in CiscoSecure. After the PIX Firewall authenticates a user, it can then use the RADIUS attribute (attribute 11, filter-id) returned by the authentication server to identify an access list for a given user group. To maintain consistency, PIX Firewall also provides the same functionality for TACACS+. Note Access lists can be used with either RADIUS or TACACS but authorizing FTP, HTTP, or Telnet is only possible with TACACS+. To restrict users in a department to three servers and deny everything else, the access-list command statements are as follows: access-list eng permit ip any server1 255.255.255.255 access-list eng permit ip any server2 255.255.255.255 access-list eng permit ip any server3 255.255.255.255 access-list eng deny ip any any 3-10 Cisco PIX Firewall and VPN Configuration Guide 78-13943-01 Chapter 3 Controlling Network Access and Use Access Control Configuration Example In this example, the vendor-specific attribute string in the CiscoSecure configuration has been set to acl=eng. Use this field in the CiscoSecure configuration to identify the access-list identification name. The PIX Firewall gets the acl=acl_ID from CiscoSecure and extracts the ACL number from the attribute string, which it puts in a user’s uauth entry. When a user tries to open a connection, PIX Firewall checks the access list in the user’s uauth entry, and depending on the permit or deny status of the access list match, permits or denies the connection. When a connection is denied, PIX Firewall generates a corresponding syslog message. If there is no match, then the implicit rule is to deny. Because the source IP of a given user can vary depending on where they are logging in from, set the source address in the access-list command statement to any, and the destination address to identify the network services to which user is permitted or denied access. The aaa authorization command does not require or provide a separate RADIUS option. To enable RADIUS authorization, perform the following steps: Step 1 Enable RADIUS authentication with the aaa authentication command. Step 2 Create the access-list command statements to specify the services that hosts are authorized to use with RADIUS in the PIX Firewall. Step 3 Configure the authentication server with the vendor-specific acl=acl_ID identifier to specify the access-list ID. When the PIX Firewall sends a request to the authentication server, it returns the acl=acl_ID string, which tells PIX Firewall to use the access-list command statements to determine how RADIUS users are authorized. Access Control Configuration Example This section provides an example of how to implement access control and includes the following topics: • Basic Configuration • Authentication and Authorization • Managing Access to Services [...]... Chapter 3 Controlling Network Access and Use Simplifying Access Control with Object Grouping A downloadable ACL without a name is assigned a name by the PIX Firewall after it is downloaded in the following format: AAA-user-username Where username is the name of the user that is being authenticated If an access- list command statement has a syntax or semantics error, or if the no access- list command is used... Firewall and VPN Configuration Guide 78-13943-01 3-23 Chapter 3 Controlling Network Access and Use Simplifying Access Control with Object Grouping Configuring Network Object Groups This section describes the commands required to configure a network object group Enter the following command to enable the network object subcommand mode: pix(config)# object-group network grp-id Enter the following command to... following command identifies an object group containing trusted hosts: pix(config)# object-group network TrustedHosts When you enter this command, the system enters the network object subcommand mode and the PIX Firewall system prompt appears as follows: pix(config -network) # Cisco PIX Firewall and VPN Configuration Guide 78-13943-01 3-21 Chapter 3 Controlling Network Access and Use Simplifying Access Control... object-group network ftp_servers pix(config -network) # network- object host 201.165.201.3 pix(config -network) # network- object host 201.165.201.4 pix(config -network) # exit pix(config)# object-group network TrustedHosts pix(config -network) # network- object host sjc.eng.ftp pix(config -network) # network- object host 201.165.201.1 pix(config -network) # network- object 192.168.1.0 255.255.255.0 pix(config -network) #... resulting downloaded access- list commands on PIX Firewall are as follows: access- list access- list access- list access- list access- list access- list AAA-user-foo; 5 elements AAA-user-foo permit tcp 13.0.0.0 255.0.0.0 11.0.0.0 255.0.0.0 AAA-user-foo permit udp 13.0.0.0 255.0.0.0 11.0.0.0 255.0.0.0 AAA-user-foo permit icmp 13.0.0.0 255.0.0.0 11.0.0.0 255.0.0.0 AAA-user-foo deny tcp any any AAA-user-foo deny udp... for Web access: static (inside, outside) 209.165.201.11 10.1.1.11 access- list acl_out permit tcp any host 209.165.201.11 eq 80 Cisco PIX Firewall and VPN Configuration Guide 78-13943-01 3-13 Chapter 3 Controlling Network Access and Use Using TurboACL The static command statement with the access- list command statement establishes an externally visible IP address for Web access (port 80 in the access- list... access- list commands with each command on a separate line Each command must be entered without the access- list keyword and the name for the access list because they are not needed The rest of the command line must conform to the syntax and semantics rules of the PIX Firewall access- list command A PIX Firewall Syslog message will be logged if there is an error in a downloaded access- list command The following... 1.1.1.1 Refer to the access list or conduit commands in the Cisco PIX Firewall Command Reference for the detailed syntax of these commands Step 7 (Optional) Use the show access- list command to display the expanded access list entries: pix(config)# show access- list access- list acl permit tcp host 201.165.201.1 host 1.1.1.1 access- list acl permit tcp 192.168.1.0 255.255.255.0 host 1.1.1.1 access- list acl... pix(config -network) # Enter a question mark (?) in the subcommand mode to view the permitted subcommands In subcommand mode, you can enter object grouping subcommands as well as all other PIX Firewall commands including show commands and clear commands When you enter any valid configuration command, such as access- list, the subcommand mode is terminated You can also terminate the subcommand mode by... servers and not with TACACS+ servers Cisco PIX Firewall and VPN Configuration Guide 3-16 78-13943-01 Chapter 3 Controlling Network Access and Use Downloading Access Lists The following are the two methods for downloading an access list from an AAA server to the PIX Firewall: • Downloading a named access list—Configure a user (real) authentication profile to include a Shared Profile Component (SPC) and . Firewall and VPN Configuration Guide 78-13943-01 Chapter 3 Controlling Network Access and Use Allowing Inbound Connections You use the access- list and access- group. specific website. Define access restrictions with the access- list command, and use the access- group command to bind the access- list command statements to an