Sửa chữa DAEWOO-LACETTI 2010 - P8

The Daewoo Lacetti is a compact car made by the South Korean automaker GM Daewoo since 2002. The first-generation Lacetti was available as a four-door sedan, a five-door hatchback or a five-door station wagon.

NUBIRA/LACETTI FENDER, HOOD, TAILGATE AND TRUNK LID 7–1SECTION 7FENDER, HOOD, TAILGATE AND TRUNK LIDCONTENTS1. FENDER 7 – 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.REPAIR PROCEDURE 7–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. HOOD 7 – 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1.REPAIR PROCEDURE 7–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. TAILGATE(HATCHBACK) 7 – 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1.REPAIR PROCEDURE 7–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. TRUNK LID (NOTCHBACK) 7 – 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.REPAIR PROCEDURE 7–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–2 FENDER, HOOD, TAILGATE AND TRUNK LID NUBIRA/LACETTI1. FENDER1–1. REPAIR PROCEDURE1. Remove the related parts.S Front bumper and mud guard 2. Remove the fender.3. Preparation of the new fender.S Preparation of the new fender and check damagedareas 4. Apply the paint CAUTIONS Ventilate when spraying paint. Most paint contains sub-stances that are harmful if inhaled or swallowed, Readthe paint label before opening paint container.S Avoid contact with skin, Wear an approved respirator,gloves, eye protection and appropriate clothing whenpainting.S Paint is flammable. Store in a safe place, and keep itaway from sparks, flames or cigarettes.5. Apply the mastic sealer.S Apply the mastic sealer to the mounting bolts.Fig. 16. Preinstall the fender.S Fasten to the wheelhouse at two places with bolts. Closethe hood and check the front and rear clearances andlevel differences of the hood and door.Fig. 27. Tighten fully.S After checking and adjusting the mounting position,tighten all bolts fully 8. Install the related parts.S Install in the reverse order in which they were removed 9. Check clearanceS Check clearance of front bumper. NUBIRA/LACETTI FENDER, HOOD, TAILGATE AND TRUNK LID 7–32. HOOD2–1. REPAIR PROCEDURE1. Remove the related parts.2. Remove the hood.S Remove the hood mounting bolts from two hinge bows.Fig. 33. Preparation of the new hood.S Preparation of the new hood and check damaged areas 4. Apply the paint CAUTIONS Ventilate when spraying paint. Most paint contains sub-stances that are harmful if inhaled or swallowed.S Read the paint label before opening paint container.S Avoid contact with skin. Wear an approved respirator,gloves, eye protection and appropriate clothing whenpainting.S Paint is flammable. Store in a safe place, and keep itaway from sparks, flames or cigarettes 5. Preinstall the hood.S Fasten to the hood hinges bows at two places with fourbolts, carefully.Fig. 4S Close the hood and check the front and rear clearancesand level difference of hood. fender and head lamps.Fig. 56. Tighten fully.S After checking and adjusting the mounting position,tighten all bolts fully 7. Install the related parts.S Install in the reverse order in which they were removed 8. Check and adjust.S Check clearances and level differences.S Check the hood locking and unlocking condition. 7–4 FENDER, HOOD, TAILGATE AND TRUNK LID NUBIRA/LACETTI3. TAILGATE (HATCHBACK)3–1. REPAIR PROCEDURE1. Remove the related parts.S Wiring harness.S Rear wiper arm and motor.S Rear window glass.S Lock set, latch and others 2. Remove the tailgate.S Remove the tailgate mounting bolts from two hingebows.Fig. 63. Preparation of the new tailgate.S Preparation of the new tailgate and check damagedareas 4. Apply the paint.CAUTIONS Ventilate when spraying paint. Most paint contains sub-stances that are harmful if inhaled or swallowed.S Avoid contact with skin. Wear an approved respirator,gloves, eye protection and approriate clothing whenpainting.S Paint is flammable. Store in a safe place, and keep itaway from sparks, flames or cigarettes.5. Preinstall the tailgate.S Fasten to the tailgate hinges at two places with fourbolts, carefully.S Install bumper.S Close the tailgate and check the clearances and leveldifference of tailgate, side panel outers and rear com-bination lamps.Fig. 76. Tighten fully.S After checking and adjusting the mounting position,tighten all bolts fully 7. Install the related parts.S Wiring harness and solenoid valve.S Lock set, latches and linkages.S Install the rear window glass.S Install in the reverse order in which they were removed 8. Check and adjust.S Clean the luggage compartment.S Check clearances and level differences.S Check the luggage locking and unlocking condition.S Check for water leaks in the luggage compartment.S Check the rear glass demist operation. NUBIRA/LACETTI FENDER, HOOD, TAILGATE AND TRUNK LID 7–54. TRUNK LID (NOTCHBACK)4–1. REPAIR PROCEDURE1. Remove the related parts.S Wiring harness and solenoid valve.S Lock set, latch set and others 2. Remove the trunk lid.S Remove the trunk lid mounting bolts from two hingebows.Fig. 83. Preparation of the new trunk lid.S Preparation of the new trunk lid and check damagedareas 4. Apply the paint CAUTIONS Ventilate when spraying paint. Most paint contains sub-stances that are harmful if inhaled or swallowed. Readthe paint label before opening paint container.S Avoid contact with skin. Wear an approved respirator,gloves, eye protection and appropriate clothing whenpainting.S Paint is flammable. Store in a safe place, and keep itaway from sparks, flames or cigarettes.5. Preinstall the trunk lid.S Fasten to the trunk lid hinges bows at two places withfour bolts, carefully.S Install bumper.Fig. 9S Close the trunk lid and check the clearances and leveldifference of trunk lid, side panel outers and rear com-bination lamps.Fig. 106. Tighten fully.S After checking and adjusting the mounting position,tighten all bolts fully 7. Install the related parts.S Washer hose and nozzles.S Install in the reverse order in which they were removed 7–6 FENDER, HOOD, TAILGATE AND TRUNK LID NUBIRA/LACETTI8. Check and adjust.S Check clearances and level differences.S Check the hood locking and unlocking condition.S Check spary conditions of washer liquid and adjustwasher spray nozzels on the hood panel . Apply the paint..CAUTIONS Ventilate when spraying paint. Most paint contains sub-stances that are harmful if inhaled or swallowed, Readthe paint label before. Apply the paint..CAUTIONS Ventilate when spraying paint. Most paint contains sub-stances that are harmful if inhaled or swallowed.S Read the paint label before