ASME B36.10M2004 Welded and Seamless Wrought Steel Pipe

ASME B36.10M-2004 (Revision of ASME B36.10M-2000) Welded and Seamless Wrought Steel Pipe A N A M E R I C A N N AT I O N A L STA N DA R D umentCopyright provided ASME by IHSInternational Licensee=Bureau Veritas/5959906001, 10/28/2004 16:59 MDT Provided Questions by IHSor under comments licenseabout with ASME this message: please call the Document cy Group at 303-397-2295 A M E R I C A N `,`,`,`,,`,`,,,`,``,`,,`,,-`-`,,`,,`,`,,` - A N N A T I O N A L S T A N D A R D WELDED AND SEAMLESS WROUGHT STEEL PIPE ASME B36.10M-2004 (Revision of ASME B36.10M-2000) Date of Issuance: October 25, 2004 This Standard will be revised when the Society approves the issuance of a new edition There will be no addenda or written interpretations of the requirements of this Standard issued to this edition ASME is the registered trademark of the American Society of Mechanical Engineers This code or standard was developed under procedures accredited as meeting the criteria for American National Standards The Consensus Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large ASME does not ‘‘approve,’’ ‘‘rate,’’ or ‘‘endorse’’ any item, construction, proprietary device, or activity ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assume any such liability Users of a code or standard are expressly advised that the determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher The American Society of Mechanical Engineers Three Park Avenue, New York, NY 10016-5990 Copyright © 2004 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All rights reserved Printed in U.S.A Foreword Committee Roster iv vi Scope Size Materials Wall Thickness Weights Permissible Variations Pipe Threads Wall Thickness Designations Wall Thickness Selection Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe iii `,`,`,`,,`,`,,,`,``,`,,`,,-`-`,,`,,`,`,,` - CONTENTS FOREWORD `,`,`,`,,`,`,,,`,``,`,,`,,-`-`,,`,,`,`,,` - In March 1927, the American Standards Association authorized the organization of a Sectional Committee on Standardization of Dimensions and Material of Wrought Steel and Wrought Iron Pipe and Tubing for the purpose of unifying the standards of these commodities in force in this country The American Society for Testing and Materials and The American Society of Mechanical Engineers were designated as sponsors, and the first meeting of the Sectional Committee was held in Pittsburgh, Pennsylvania, on May 18, 1928 The dimensions of commercial pipe in general use in the United States at the time conformed rather generally to those recommended by the ASME Committee on Standard Pipe and Pipe Threads published in 1886 (ASME Transactions, Vol VIII, p 29) On these standards an enormous industry has been built and the satisfactory use of this product proves the soundness of the original design and specification Increasingly severe service demands at the time of the Committee’s organization had been met by using the nearest available pipe or tubing for heavier sections such as casing, mechanical tubing, etc., with resulting uneconomical multiplicity of wall thicknesses Subsequently, the Committee, with the cooperation of the industry, made a survey of existing practice as the logical starting point for the development of an American Standard From this survey, a table was designed to provide a selection of wall thicknesses of pipe to cover the power piping requirements of industry where strength to resist internal pressure governs selection and was later expanded to include pipe diameters and thicknesses used in other industries The original intent of the Committee was to establish a system of Schedule Numbers for pipe size/wall thickness combinations which would have an approximately uniform relationship equal to 1000 times the P/S expression contained in the modified Barlow formula for pipe wall thickness as defined in the Appendix to this standard The resulting Numbers departed so far from existing wall thicknesses in common use that the original intent could not be accomplished The Schedule Numbers were then adopted strictly as a convenient designation system for use in ordering In all cases, the designer must base his selection on the rules and allowable stresses set by the code which governs his particular construction The table is dimensionally complete for all sizes and wall thicknesses within its scope, but some of the larger, heavier wall sections are beyond the capability of seamless mill production and must be obtained from forged and bored billets or other sources The first issue of this standard was given with the designation American Standard “tentative” by the American Standards Association in November 1935 Subsequent slight revisions to Table and the footnotes of the dimensional tables were approved and the ASA changed the designation to American Standard; the date of ASA approval was April 28, 1939 Further revisions were made by the Sectional Committee The list of specifications in Table was revised where necessary and slight revisions in wall thicknesses of some of the large sizes of the heavy schedules were made where P/S values were out of line It was the hope in 1939 that the designation of pipe used commercially by all industry as Standard weight, Extra-Strong, and Double Extra-Strong would gradually be replaced by Schedule Number designation However, owing to customs of over 50 years’ standing, demand and production of pipe to these traditional dimensions is undiminished Consequently, in response to a demand from users, accepted practice for dimensions and weights of commercial wrought steel and welded wrought iron pipe were added These changes were designated an American Standard on February 23, 1950 Subcommittee No was reorganized in 1957 In addition to necessary editorial changes, a simplified format was selected for the tables of weights and dimensions so as to include and identify the sizes and weights of API Standards 5L and 5LX These changes to the standard were approved and it was designated an American Standard on December 21, 1959 The standard was revised in 1969 A uniform method to calculate the plain end weight of steel pipe was included, and minor adjustments were made in the tabulated weights of steel pipe in iv v `,`,`,`,,`,`,,,`,``,`,,`,,-`-`,,`,,`,`,,` - Table to conform to this new method Additional sizes and thicknesses of steel pipe that had come into common use were also added to Table Inasmuch as API Standard 5L no longer included wrought iron pipe, reference to this API Standard was deleted from Table These changes to the standard were approved and it was designated an American National Standard on February 3, 1970 Further revisions were made to the standard in 1975 Additional sizes and thicknesses of steel pipe that had been added to API specifications were added to Table Table 3, Dimensions and Weights of Welded Wrought Iron Pipe, was deleted in its entirety, since wrought iron pipe is no longer produced These changes in the standard were approved and it was designated an American National Standard on June 5, 1975 The standard was revised in 1978 to include SI metric dimensions The outside diameter and wall thicknesses were converted to millimeters by multiplying the inch dimensions by 25.4 Outside diameters larger than 16 in were rounded to the nearest millimeter, and outside diameters 16 in and smaller were rounded to the nearest 0.1 mm Wall thicknesses were rounded to the nearest 0.01 mm These converted and rounded SI metric dimensions were added to Table A formula to calculate the SI metric plain end mass, in kilograms per meter, using SI metric diameters and thicknesses was added to section The SI metric plain end mass was calculated and was added to Table These changes in the standard were approved and it was designated an American National Standard on July 18, 1979 Further revisions were made in 1984 The ANSI designations, which are no longer in use, were deleted from Table 1, and the list of specifications was revised to agree with current ASTM and API specifications Additional sizes and thicknesses which had been added to API specifications were added to Table That edition was approved as an American National Standard on August 19, 1985 The next edition included additional wall thicknesses and was approved by the American National Standards Institute on August 24, 1995 The 1996 edition contained revisions to Table 2, adding pipe sizes, changing some plain end weights and masses, identifying metric pipe by the dimensionless designator DN, and eliminating the API Specification column The 1996 edition was approved as an American National Standard on September 23, 1996 The 2000 edition contained revisions to Table to include the revised density for steel incorporated into Section previously Table was deleted and other editorial changes to Sections 1, 2, 3, 5, 8, and were made The 2000 edition was approved as an American National Standard on December 1, 2000 The current edition contains revisions to Section and Table It corrects the equation for nominal plain end weight It adds the missing DN schedule numbers in Table This edition was approved as an American National Standard on June 23, 2004 ASME B32 COMMITTEE Metal and Metal Alloy Wrought Mill Product Nominal Sizes (The following is the roster of the Committee at the time of approval of this Standard.) OFFICERS J A Gruber, Chair J H Karian, Secretary COMMITTEE PERSONNEL `,`,`,`,,`,`,,,`,``,`,,`,,-`-`,,`,,`,`,,` - F M Christensen, F M Christensen Metallurgical Consulting, Inc A Cohen, Arthur Cohen & Associates J A Gruber, Wheatland Tube Co W N Holliday, LTV Steel Co L T Ingels, American Gas Association, Inc J H Karian, The American Society of Mechanical Engineers K O Kverneland, Kok Metric Co A R Machell, Jr P Pollak, Aluminum Association, Inc R N Rau vi ASME B36.10M-2004 WELDED AND SEAMLESS WROUGHT STEEL PIPE SCOPE D p outside diameter to the nearest 0.001 in (the symbol D is to be used for OD only in mathematical equations or formulas) Wpe p nominal plain end mass, rounded to the nearest 0.01 lb/ft t p specified wall thickness, rounded to the nearest 0.001 in This Standard covers the standardization of dimensions of welded and seamless wrought steel pipe for high or low temperatures and pressures The word pipe is used, as distinguished from tube, to apply to tubular products of dimensions commonly used for pipeline and piping systems Pipe NPS 12 (DN 300) and smaller have outside diameters numerically larger than their corresponding sizes In contrast, the outside diameters of tubes are numerically identical to the size number for all sizes The nominal plain end mass, in kilograms per meter, is calculated using the following formula: Wpe p 0.0246615(D − t)t where D p outside diameter to the nearest 0.1 mm for outside diameters that are 16 in (406.4 mm) and smaller and to the nearest 1.0 mm for outside diameters larger than 16 in (406.4 mm) (the symbol D is to be used for OD only in mathematical equations or formulas) Wpe p nominal plain end mass, rounded to the nearest 0.01 kg/m t p specified wall thickness, rounded to the nearest 0.01 mm SIZE The size of all pipe is identified by the nominal pipe size The manufacture of pipe NPS 1⁄8 (DN 6) to NPS 12 (DN 300), inclusive, is based on a standardized outside diameter (OD) This OD was originally selected so that pipe with a standard OD and having a wall thickness that was typical of the period would have an inside diameter (ID) approximately equal to the nominal size Although there is no such relation between the existing standard thickness — OD and nominal size — these nominal sizes and standard ODs continue in use as ‘‘standard.’’ The manufacture of pipe NPS 14 (DN 350) and larger proceeds on the basis of an OD corresponding to the nominal size Variations in dimensions differ depending upon the method of manufacture employed in making the pipe to the various specifications available Permissible variations for dimensions are indicated in each specification MATERIALS The dimensional standards for pipe described here are for products covered in ASTM specifications PIPE THREADS Unless otherwise specified, the threads of threaded pipe shall conform to ANSI / ASME B1.20.1, Pipe Threads, General Purpose (Inch) Schedules and 10 wall thicknesses not permit threading in accordance with ANSI/ASME B1.20.1 WALL THICKNESS The nominal wall thicknesses are given in Table PERMISSIBLE VARIATIONS WEIGHTS The nominal weights of steel pipe are calculated values and are tabulated in Table The nominal plain end weight, in pounds per foot, is calculated using the following formula: WALL THICKNESS DESIGNATIONS The wall thickness designations Standard, ExtraStrong, and Double Extra-Strong have been commercially used designations for many years As explained in the Foreword, the Schedule Numbers were subsequently added as a convenient designation for use in ordering pipe Standard and Schedule 40 are identical for up to NPS 10 (DN 250), inclusive All larger sizes of Standard Wpe p 10.69(D − t)t where ASME B36.10M-2004 WELDED AND SEAMLESS WROUGHT STEEL PIPE have 3⁄8 in (9.53 mm) wall thicknesses Extra-Strong and Schedule 80 are identical for up to NPS (DN 200), inclusive All larger sizes of Extra-Strong have 1⁄2 in (12.70 mm) wall thicknesses Pipe of sizes and wall thicknesses other than those of Standard, Extra-Strong, and Double Extra-Strong, and Schedule Number were adopted from API Specification 5L It was not considered practical to establish Schedule Numbers or new designations for them conditions, the designer shall compute the exact value of wall thickness suitable for conditions for which the pipe is required, as prescribed in detail in the ASME Boiler and Pressure Vessel Code, ASME B31 Code for Pressure Piping, or other similar codes, whichever governs the construction A thickness shall be selected from Table to suit the value computed to fulfill the conditions for which the pipe is desired WALL THICKNESS SELECTION When the selection of wall thickness depends primarily upon capacity to resist internal pressure under given `,`,`,`,,`,`,,,`,``,`,,`,,-`-`,,`,,`,`,,` - WELDED AND SEAMLESS WROUGHT STEEL PIPE ASME B36.10M-2004 Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe Customary Units SI Units Outside Diameter, in Wall Thickness, in ⁄8 ⁄8 ⁄8 ⁄8 0.405 0.405 0.405 0.405 0.049 0.057 0.068 0.095 0.19 0.21 0.24 0.31 STD XS 10 30 40 80 (3) (3) (3) (3) 10.3 10.3 10.3 10.3 1.24 1.45 1.73 2.41 0.28 0.32 0.37 0.47 ⁄4 ⁄4 ⁄4 ⁄4 0.540 0.540 0.540 0.540 0.065 0.073 0.088 0.119 0.33 0.36 0.43 0.54 STD XS 10 30 40 80 (3) (3) (3) (3) 13.7 13.7 13.7 13.7 1.65 1.85 2.24 3.02 0.49 0.54 0.63 0.80 ⁄8 ⁄8 ⁄8 ⁄8 0.675 0.675 0.675 0.675 0.065 0.073 0.091 0.126 0.42 0.47 0.57 0.74 STD XS 10 30 40 80 10 10 10 10 17.1 17.1 17.1 17.1 1.65 1.85 2.31 3.20 0.63 0.70 0.84 1.10 ⁄2 ⁄2 ⁄2 ⁄2 0.840 0.840 0.840 0.840 0.065 0.083 0.095 0.109 0.54 0.67 0.76 0.85 STD 10 30 40 15 15 15 15 21.3 21.3 21.3 21.3 1.65 2.11 2.41 2.77 0.80 1.00 1.12 1.27 ⁄2 ⁄2 ⁄2 0.840 0.840 0.840 0.147 0.188 0.294 1.09 1.31 1.72 XS XXS 80 160 15 15 15 21.3 21.3 21.3 3.73 4.78 7.47 1.62 1.95 2.55 ⁄4 ⁄4 ⁄4 ⁄4 1.050 1.050 1.050 1.050 0.065 0.083 0.095 0.113 0.69 0.86 0.97 1.13 STD 10 30 40 20 20 20 20 26.7 26.7 26.7 26.7 1.65 2.11 2.41 2.87 1.03 1.28 1.44 1.69 ⁄4 ⁄4 ⁄4 1.050 1.050 1.050 0.154 0.219 0.308 1.48 1.95 2.44 XS XXS 80 160 20 20 20 26.7 26.7 26.7 3.91 5.56 7.82 2.20 2.90 3.64 1 1 1.315 1.315 1.315 1.315 0.065 0.109 0.114 0.133 0.87 1.41 1.46 1.68 STD 10 30 40 25 25 25 25 33.4 33.4 33.4 33.4 1.65 2.77 2.90 3.38 1.29 2.09 2.18 2.50 1 1.315 1.315 1.315 0.179 0.250 0.358 2.17 2.85 3.66 XS XXS 80 160 25 25 25 33.4 33.4 33.4 4.55 6.35 9.09 3.24 4.24 5.45 11⁄4 11⁄4 11⁄4 11⁄4 1.660 1.660 1.660 1.660 0.065 0.109 0.117 0.140 1.11 1.81 1.93 2.27 STD 10 30 40 32 32 32 32 42.2 42.2 42.2 42.2 1.65 2.77 2.97 3.56 1.65 2.69 2.87 3.39 11⁄4 11⁄4 11⁄4 1.660 1.660 1.660 0.191 0.250 0.382 3.00 3.77 5.22 XS XXS 80 160 32 32 32 42.2 42.2 42.2 4.85 6.35 9.70 4.47 5.61 7.77 11⁄2 11⁄2 11⁄2 11⁄2 1.900 1.900 1.900 1.900 0.065 0.109 0.125 0.145 1.28 2.09 2.37 2.72 STD 10 30 40 40 40 40 40 48.3 48.3 48.3 48.3 1.65 2.77 3.18 3.68 1.90 3.11 3.53 4.05 11⁄2 11⁄2 11⁄2 1.900 1.900 1.900 0.200 0.281 0.400 3.63 4.86 6.41 XS XXS 80 160 40 40 40 48.3 48.3 48.3 5.08 7.14 10.15 5.41 7.25 9.55 NPS [Note (1)] 1 1 3 Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No DN [Note (2)] Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m WELDED AND SEAMLESS WROUGHT STEEL PIPE ASME B36.10M-2004 Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Customary Units Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No DN [Note (2)] SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in 31⁄2 31⁄2 31⁄2 31⁄2 4.000 4.000 4.000 4.000 0.226 0.250 0.281 0.318 9.12 10.02 11.17 12.52 STD XS 40 80 90 90 90 90 101.6 101.6 101.6 101.6 5.74 6.35 7.14 8.08 13.57 14.92 16.63 18.64 4 4 4.500 4.500 4.500 4.500 0.083 0.109 0.120 0.125 3.92 5.12 5.62 5.85 10 100 100 100 100 114.3 114.3 114.3 114.3 2.11 2.77 3.05 3.18 5.84 7.62 8.37 8.71 4 4 4.500 4.500 4.500 4.500 0.141 0.156 0.172 0.188 6.57 7.24 7.96 8.67 30 100 100 100 100 114.3 114.3 114.3 114.3 3.58 3.96 4.37 4.78 9.78 10.78 11.85 12.91 4 4 4.500 4.500 4.500 4.500 0.203 0.219 0.237 0.250 9.32 10.02 10.80 11.36 STD 40 100 100 100 100 114.3 114.3 114.3 114.3 5.16 5.56 6.02 6.35 13.89 14.91 16.08 16.91 4 4 4.500 4.500 4.500 4.500 0.281 0.312 0.337 0.438 12.67 13.97 15.00 19.02 XS 80 120 100 100 100 100 114.3 114.3 114.3 114.3 7.14 7.92 8.56 11.13 18.87 20.78 22.32 28.32 4 4.500 4.500 0.531 0.674 22.53 27.57 XXS 160 100 100 114.3 114.3 13.49 17.12 33.54 41.03 5 5 5.563 5.563 5.563 5.563 0.083 0.109 0.125 0.134 4.86 6.36 7.27 7.78 10 125 125 125 125 141.3 141.3 141.3 141.3 2.11 2.77 3.18 3.40 7.24 9.46 10.83 11.56 5 5 5 5 5.563 5.563 5.563 5.563 5.563 5.563 5.563 5.563 0.156 0.188 0.219 0.258 0.281 0.312 0.344 0.375 9.02 10.80 12.51 14.63 15.87 17.51 19.19 20.80 STD XS 40 80 125 125 125 125 125 125 125 125 141.3 141.3 141.3 141.3 141.3 141.3 141.3 141.3 3.96 4.78 5.56 6.55 7.14 7.92 8.74 9.53 13.41 16.09 18.61 21.77 23.62 26.05 28.57 30.97 5 5.563 5.563 5.563 0.500 0.625 0.750 27.06 32.99 38.59 XXS 120 160 125 125 125 141.3 141.3 141.3 12.70 15.88 19.05 40.28 49.12 57.43 6 6 6.625 6.625 6.625 6.625 0.083 0.109 0.125 0.134 5.80 7.59 8.69 9.30 10 150 150 150 150 168.3 168.3 168.3 168.3 2.11 2.77 3.18 3.40 8.65 11.31 12.95 13.83 6 6 6.625 6.625 6.625 6.625 0.141 0.156 0.172 0.188 9.77 10.79 11.87 12.94 150 150 150 150 168.3 168.3 168.3 168.3 3.58 3.96 4.37 4.78 14.54 16.05 17.67 19.28 6 6 6.625 6.625 6.625 6.625 0.203 0.219 0.250 0.280 13.94 15.00 17.04 18.99 STD 40 150 150 150 150 168.3 168.3 168.3 168.3 5.16 5.56 6.35 7.11 20.76 22.31 25.36 28.26 Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m ASME B36.10M-2004 WELDED AND SEAMLESS WROUGHT STEEL PIPE Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in 6 6 6.625 6.625 6.625 6.625 0.312 0.344 0.375 0.432 21.06 23.10 25.05 28.60 XS 80 150 150 150 150 168.3 168.3 168.3 168.3 7.92 8.74 9.53 10.97 31.33 34.39 37.31 42.56 6 6.625 6.625 6.625 0.500 0.562 0.625 32.74 36.43 40.09 120 150 150 150 168.3 168.3 168.3 12.70 14.27 15.88 48.73 54.21 59.69 6 6 6.625 6.625 6.625 6.625 0.719 0.750 0.864 0.875 45.39 47.10 53.21 53.78 XXS 160 150 150 150 150 168.3 168.3 168.3 168.3 18.26 19.05 21.95 22.23 67.57 70.12 79.22 80.08 8 8 8.625 8.625 8.625 8.625 0.109 0.125 0.148 0.156 9.92 11.36 13.41 14.12 10 200 200 200 200 219.1 219.1 219.1 219.1 2.77 3.18 3.76 3.96 14.78 16.93 19.97 21.01 8 8 8.625 8.625 8.625 8.625 0.188 0.203 0.219 0.250 16.96 18.28 19.68 22.38 20 200 200 200 200 219.1 219.1 219.1 219.1 4.78 5.16 5.56 6.35 25.26 27.22 29.28 33.32 8 8 8.625 8.625 8.625 8.625 0.277 0.312 0.322 0.344 24.72 27.73 28.58 30.45 STD 30 40 200 200 200 200 219.1 219.1 219.1 219.1 7.04 7.92 8.18 8.74 36.82 41.25 42.55 45.34 8 8 8.625 8.625 8.625 8.625 0.375 0.406 0.438 0.500 33.07 35.67 38.33 43.43 XS 60 80 200 200 200 200 219.1 219.1 219.1 219.1 9.53 10.31 11.13 12.70 49.25 53.09 57.08 64.64 8 8 8.625 8.625 8.625 8.625 0.562 0.594 0.625 0.719 48.44 51.00 53.45 60.77 100 120 200 200 200 200 219.1 219.1 219.1 219.1 14.27 15.09 15.88 18.26 72.08 75.92 79.59 90.44 8 8 8.625 8.625 8.625 8.625 8.625 0.750 0.812 0.875 0.906 1.000 63.14 67.82 72.49 74.76 81.51 XXS 140 160 200 200 200 200 200 219.1 219.1 219.1 219.1 219.1 19.05 20.62 22.23 23.01 25.40 93.98 100.93 107.93 111.27 121.33 10 10 10 10 10.750 10.750 10.750 10.750 0.134 0.156 0.165 0.188 15.21 17.67 18.67 21.23 10 250 250 250 250 273.0 273.0 273.0 273.0 3.40 3.96 4.19 4.78 22.61 26.27 27.78 31.62 10 10 10 10 10.750 10.750 10.750 10.750 0.203 0.219 0.250 0.279 22.89 24.65 28.06 31.23 20 250 250 250 250 273.0 273.0 273.0 273.0 5.16 5.56 6.35 7.09 34.08 36.67 41.76 46.49 10 10 10 10 10.750 10.750 10.750 10.750 0.307 0.344 0.365 0.438 34.27 38.27 40.52 48.28 STD 30 40 250 250 250 250 273.0 273.0 273.0 273.0 7.80 8.74 9.27 11.13 51.01 56.96 60.29 71.88 DN [Note (2)] Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m `,`,`,`,,`,`,,,`,``,`,,`,,-`-`,,`,,`,`,,` - Customary Units WELDED AND SEAMLESS WROUGHT STEEL PIPE ASME B36.10M-2004 Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Customary Units Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in 10 10 10 10 10.750 10.750 10.750 10.750 0.500 0.562 0.594 0.625 54.79 61.21 64.49 67.65 XS 60 80 250 250 250 250 273.0 273.0 273.0 273.0 12.70 14.27 15.09 15.88 81.53 91.05 95.98 100.69 10 10 10 10 10.750 10.750 10.750 10.750 0.719 0.812 0.844 0.875 77.10 86.26 89.38 92.37 100 120 250 250 250 250 273.0 273.0 273.0 273.0 18.26 20.62 21.44 22.23 114.71 128.34 133.01 137.48 10 10 10 10 10.750 10.750 10.750 10.750 0.938 1.000 1.125 1.250 98.39 104.23 115.75 126.94 XXS 140 160 250 250 250 250 273.0 273.0 273.0 273.0 23.83 25.40 28.58 31.75 146.43 155.10 172.27 188.90 12 12 12 12 12.750 12.750 12.750 12.750 0.156 0.172 0.180 0.188 21.00 23.13 24.19 25.25 10 300 300 300 300 323.8 323.8 323.8 323.8 3.96 4.37 4.57 4.78 31.24 34.43 35.98 37.61 12 12 12 12 12.750 12.750 12.750 12.750 0.203 0.219 0.250 0.281 27.23 29.34 33.41 37.46 20 300 300 300 300 323.8 323.8 323.8 323.8 5.16 5.56 6.35 7.14 40.55 43.64 49.71 55.76 12 12 12 12 12.750 12.750 12.750 12.750 0.312 0.330 0.344 0.375 41.48 43.81 45.62 49.61 STD 30 300 300 300 300 323.8 323.8 323.8 323.8 7.92 8.38 8.74 9.53 61.70 65.19 67.91 73.86 12 12 12 12 12.750 12.750 12.750 12.750 0.406 0.438 0.500 0.562 53.57 57.65 65.48 73.22 XS 40 60 300 300 300 300 323.8 323.8 323.8 323.8 10.31 11.13 12.70 14.27 79.71 85.82 97.44 108.93 12 12 12 12 12.750 12.750 12.750 12.750 0.625 0.688 0.750 0.812 81.01 88.71 96.21 103.63 80 300 300 300 300 323.8 323.8 323.8 323.8 15.88 17.48 19.05 20.62 120.59 132.05 143.17 154.17 12 12 12 12 12.750 12.750 12.750 12.750 0.844 0.875 0.938 1.000 107.42 111.08 118.44 125.61 XXS 100 120 300 300 300 300 323.8 323.8 323.8 323.8 21.44 22.23 23.83 25.40 159.87 165.33 176.29 186.92 12 12 12 12 12.750 12.750 12.750 12.750 1.062 1.125 1.250 1.312 132.69 139.81 153.67 160.42 140 160 300 300 300 300 323.8 323.8 323.8 323.8 26.97 28.58 31.75 33.32 197.43 208.08 228.68 238.69 14 14 14 14 14.000 14.000 14.000 14.000 0.156 0.188 0.203 0.210 23.09 27.76 29.94 30.96 350 350 350 350 355.6 355.6 355.6 355.6 3.96 4.78 5.16 5.33 34.34 41.36 44.59 46.04 14 14 14 14 14.000 14.000 14.000 14.000 0.219 0.250 0.281 0.312 32.26 36.75 41.21 45.65 10 20 350 350 350 350 355.6 355.6 355.6 355.6 5.56 6.35 7.14 7.92 48.00 54.69 61.36 67.91 DN [Note (2)] Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m ASME B36.10M-2004 WELDED AND SEAMLESS WROUGHT STEEL PIPE Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Customary Units Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in 14 14 14 14 14.000 14.000 14.000 14.000 0.344 0.375 0.406 0.438 50.22 54.62 59.00 63.50 STD 30 40 350 350 350 350 355.6 355.6 355.6 355.6 8.74 9.53 10.31 11.13 74.76 81.33 87.79 94.55 14 14 14 14 14.000 14.000 14.000 14.000 0.469 0.500 0.562 0.594 67.84 72.16 80.73 85.13 XS 60 350 350 350 350 355.6 355.6 355.6 355.6 11.91 12.70 14.27 15.09 100.95 107.40 120.12 126.72 14 14 14 14 14 14 14 14 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 0.625 0.688 0.750 0.812 0.875 0.938 1.000 1.062 89.36 97.91 106.23 114.48 122.77 130.98 138.97 146.88 80 100 350 350 350 350 350 350 350 350 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 15.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 133.04 145.76 158.11 170.34 182.76 194.98 206.84 218.58 14 14 14 14 14.000 14.000 14.000 14.000 1.094 1.125 1.250 1.406 150.93 154.84 170.37 189.29 120 140 160 350 350 350 350 355.6 355.6 355.6 355.6 27.79 28.58 31.75 35.71 224.66 230.49 253.58 281.72 14 14 14 14 14.000 14.000 14.000 14.000 2.000 2.125 2.200 2.500 256.56 269.76 277.51 307.34 350 350 350 350 355.6 355.6 355.6 355.6 50.80 53.98 55.88 63.50 381.85 401.52 413.04 457.43 16 16 16 16 16.000 16.000 16.000 16.000 0.165 0.188 0.203 0.219 27.93 31.78 34.28 36.95 400 400 400 400 406.4 406.4 406.4 406.4 4.19 4.78 5.16 5.56 41.56 47.34 51.06 54.96 16 16 16 16 16.000 16.000 16.000 16.000 0.250 0.281 0.312 0.344 42.09 47.22 52.32 57.57 10 20 400 400 400 400 406.4 406.4 406.4 406.4 6.35 7.14 7.92 8.74 62.65 70.30 77.83 85.71 16 16 16 16 16.000 16.000 16.000 16.000 0.375 0.406 0.438 0.469 62.64 67.68 72.86 77.87 STD 30 400 400 400 400 406.4 406.4 406.4 406.4 9.53 10.31 11.13 11.91 93.27 100.71 108.49 115.87 16 16 16 16 16.000 16.000 16.000 16.000 0.500 0.562 0.625 0.656 82.85 92.75 102.72 107.60 XS 40 60 400 400 400 400 406.4 406.4 406.4 406.4 12.70 14.27 15.88 16.66 123.31 138.00 152.94 160.13 16 16 16 16 16.000 16.000 16.000 16.000 0.688 0.750 0.812 0.844 112.62 122.27 131.84 136.74 80 400 400 400 400 406.4 406.4 406.4 406.4 17.48 19.05 20.62 21.44 167.66 181.98 196.18 203.54 16 16 16 16 16.000 16.000 16.000 16.000 0.875 0.938 1.000 1.031 141.48 151.03 160.35 164.98 100 400 400 400 400 406.4 406.4 406.4 406.4 22.23 23.83 25.40 26.19 210.61 224.83 238.66 245.57 DN [Note (2)] Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m WELDED AND SEAMLESS WROUGHT STEEL PIPE ASME B36.10M-2004 Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Customary Units Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in 16 16 16 16 16.000 16.000 16.000 16.000 1.062 1.125 1.188 1.219 169.59 178.89 188.11 192.61 120 400 400 400 400 406.4 406.4 406.4 406.4 26.97 28.58 30.18 30.96 252.37 266.30 280.01 286.66 16 16 16 18 18 18 18 16.000 16.000 16.000 18.000 18.000 18.000 18.000 1.250 1.438 1.594 0.165 0.188 0.219 0.250 197.10 223.85 245.48 31.46 35.80 41.63 47.44 140 160 10 400 400 400 450 450 450 450 406.4 406.4 406.4 457 457 457 457 31.75 36.53 40.49 4.19 4.78 5.56 6.35 293.35 333.21 365.38 46.79 53.31 61.90 70.57 18 18 18 18 18.000 18.000 18.000 18.000 0.281 0.312 0.344 0.375 53.23 58.99 64.93 70.65 STD 20 450 450 450 450 457 457 457 457 7.14 7.92 8.74 9.53 79.21 87.71 96.62 105.17 18 18 18 18 18.000 18.000 18.000 18.000 0.406 0.438 0.469 0.500 76.36 82.23 87.89 93.54 XS 30 450 450 450 450 457 457 457 457 10.31 11.13 11.91 12.70 113.58 122.38 130.73 139.16 18 18 18 18 18.000 18.000 18.000 18.000 0.562 0.625 0.688 0.750 104.76 116.09 127.32 138.30 40 60 450 450 450 450 457 457 457 457 14.27 15.88 17.48 19.05 155.81 172.75 189.47 205.75 18 18 18 18 18.000 18.000 18.000 18.000 0.812 0.875 0.938 1.000 149.20 160.18 171.08 181.73 80 450 450 450 450 457 457 457 457 20.62 22.23 23.83 25.40 221.91 238.35 254.57 270.36 18 18 18 18 18.000 18.000 18.000 18.000 1.062 1.125 1.156 1.188 192.29 202.94 208.15 213.51 100 450 450 450 450 457 457 457 457 26.97 28.58 29.36 30.18 286.02 301.96 309.64 317.68 18 18 18 18 18.000 18.000 18.000 18.000 1.250 1.375 1.562 1.781 223.82 244.37 274.48 308.79 120 140 160 450 450 450 450 457 457 457 457 31.75 34.93 39.67 45.24 332.97 363.58 408.28 459.39 20 20 20 20 20.000 20.000 20.000 20.000 0.188 0.219 0.250 0.281 39.82 46.31 52.78 59.23 10 500 500 500 500 508 508 508 508 4.78 5.56 6.35 7.14 59.32 68.89 78.56 88.19 20 20 20 20 20.000 20.000 20.000 20.000 0.312 0.344 0.375 0.406 65.66 72.28 78.67 85.04 STD 20 500 500 500 500 508 508 508 508 7.92 8.74 9.53 10.31 97.68 107.61 117.15 126.54 20 20 20 20 20.000 20.000 20.000 20.000 0.438 0.469 0.500 0.562 91.59 97.92 104.23 116.78 XS 30 500 500 500 500 508 508 508 508 11.13 11.91 12.70 14.27 136.38 145.71 155.13 173.75 DN [Note (2)] Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m ASME B36.10M-2004 WELDED AND SEAMLESS WROUGHT STEEL PIPE Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Customary Units Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in 20 20 20 20 20 20 20 20 20.000 20.000 20.000 20.000 20.000 20.000 20.000 20.000 0.594 0.625 0.688 0.750 0.812 0.875 0.938 1.000 123.23 129.45 142.03 154.34 166.56 178.89 191.14 203.11 40 60 500 500 500 500 500 500 500 500 508 508 508 508 508 508 508 508 15.09 15.88 17.48 19.05 20.62 22.23 23.83 25.40 183.43 192.73 211.45 229.71 247.84 266.31 284.54 302.30 20 20 20 20 20.000 20.000 20.000 20.000 1.031 1.062 1.125 1.188 209.06 215.00 227.00 238.91 80 500 500 500 500 508 508 508 508 26.19 26.97 28.58 30.18 311.19 319.94 337.91 355.63 20 20 20 20 20.000 20.000 20.000 20.000 1.250 1.281 1.312 1.375 250.55 256.34 262.10 273.76 100 500 500 500 500 508 508 508 508 31.75 32.54 33.32 34.93 372.91 381.55 390.05 407.51 20 20 20 20.000 20.000 20.000 1.500 1.750 1.969 296.65 341.41 379.53 120 140 160 500 500 500 508 508 508 38.10 44.45 50.01 441.52 508.15 564.85 22 22 22 22 22.000 22.000 22.000 22.000 0.188 0.219 0.250 0.281 43.84 50.99 58.13 65.24 10 550 550 550 550 559 559 559 559 4.78 5.56 6.35 7.14 65.33 75.89 86.55 97.17 22 22 22 22 22.000 22.000 22.000 22.000 0.312 0.344 0.375 0.406 72.34 79.64 86.69 93.72 STD 20 550 550 550 550 559 559 559 559 7.92 8.74 9.53 10.31 107.64 118.60 129.14 139.51 22 22 22 22 22.000 22.000 22.000 22.000 0.438 0.469 0.500 0.562 100.96 107.95 114.92 128.79 XS 30 550 550 550 550 559 559 559 559 11.13 11.91 12.70 14.27 150.38 160.69 171.10 191.70 22 22 22 22 22.000 22.000 22.000 22.000 0.625 0.688 0.750 0.812 142.81 156.74 170.37 183.92 550 550 550 550 559 559 559 559 15.88 17.48 19.05 20.62 212.70 233.44 253.67 273.78 22 22 22 22 22 22.000 22.000 22.000 22.000 22.000 0.875 0.938 1.000 1.062 1.125 197.60 211.19 224.49 237.70 251.05 60 80 550 550 550 550 550 559 559 559 559 559 22.23 23.83 25.40 26.97 28.58 294.27 314.51 334.25 353.86 373.85 22 22 22 22 22 22.000 22.000 22.000 22.000 22.000 1.188 1.250 1.312 1.375 1.438 264.31 277.27 290.15 303.16 316.08 100 550 550 550 550 550 559 559 559 559 559 30.18 31.75 33.32 34.93 36.53 393.59 412.84 431.96 451.45 470.69 22 22 22 22 22.000 22.000 22.000 22.000 1.500 1.625 1.875 2.125 328.72 353.94 403.38 451.49 120 140 160 550 550 550 550 559 559 559 559 38.10 41.28 47.63 53.98 489.44 527.05 600.67 672.30 10 DN [Note (2)] Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m WELDED AND SEAMLESS WROUGHT STEEL PIPE ASME B36.10M-2004 Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Customary Units Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in 24 24 24 24 24.000 24.000 24.000 24.000 0.218 0.250 0.281 0.312 55.42 63.47 71.25 79.01 10 600 600 600 600 610 610 610 610 5.54 6.35 7.14 7.92 82.58 94.53 106.15 117.60 24 24 24 24 24.000 24.000 24.000 24.000 0.344 0.375 0.406 0.438 86.99 94.71 102.40 110.32 STD 20 600 600 600 600 610 610 610 610 8.74 9.53 10.31 11.13 129.60 141.12 152.48 164.38 24 24 24 24 24.000 24.000 24.000 24.000 0.469 0.500 0.562 0.625 117.98 125.61 140.81 156.17 XS 30 600 600 600 600 610 610 610 610 11.91 12.70 14.27 15.88 175.67 187.07 209.65 232.67 24 24 24 24 24.000 24.000 24.000 24.000 0.688 0.750 0.812 0.875 171.45 186.41 201.28 216.31 40 600 600 600 600 610 610 610 610 17.48 19.05 20.62 22.23 255.43 277.63 299.71 322.23 24 24 24 24 24.000 24.000 24.000 24.000 0.938 0.969 1.000 1.062 231.25 238.57 245.87 260.41 60 600 600 600 600 610 610 610 610 23.83 24.61 25.40 26.97 344.48 355.28 366.19 387.79 24 24 24 24 24.000 24.000 24.000 24.000 1.125 1.188 1.219 1.250 275.10 289.71 296.86 304.00 80 600 600 600 600 610 610 610 610 28.58 30.18 30.96 31.75 409.80 431.55 442.11 452.77 24 24 24 24 24.000 24.000 24.000 24.000 1.312 1.375 1.438 1.500 318.21 332.56 346.83 360.79 600 600 600 600 610 610 610 610 33.32 34.93 36.53 38.10 473.87 495.38 516.63 537.36 24 24 24 24 24 24.000 24.000 24.000 24.000 24.000 1.531 1.562 1.812 2.062 2.344 367.74 374.66 429.79 483.57 542.64 100 120 140 160 600 600 600 600 600 610 610 610 610 610 38.89 39.67 46.02 52.37 59.54 547.74 557.97 640.07 720.19 808.27 26 26 26 26 26.000 26.000 26.000 26.000 0.250 0.281 0.312 0.344 68.82 77.26 85.68 94.35 10 650 650 650 650 660 660 660 660 6.35 7.14 7.92 8.74 102.36 114.96 127.36 140.37 26 26 26 26 26.000 26.000 26.000 26.000 0.375 0.406 0.438 0.469 102.72 111.08 119.69 128.00 STD 650 650 650 650 660 660 660 660 9.53 10.31 11.13 11.91 152.88 165.19 178.10 190.36 26 26 26 26 26.000 26.000 26.000 26.000 0.500 0.562 0.625 0.688 136.30 152.83 169.54 186.16 XS 20 650 650 650 650 660 660 660 660 12.70 14.27 15.88 17.48 202.74 227.25 252.25 276.98 26 26 26 26 26 26.000 26.000 26.000 26.000 26.000 0.750 0.812 0.875 0.938 1.000 202.44 218.64 235.01 251.30 267.25 650 650 650 650 650 660 660 660 660 660 19.05 20.62 22.23 23.83 25.40 301.12 325.14 349.64 373.87 397.51 11 DN [Note (2)] Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m ASME B36.10M-2004 WELDED AND SEAMLESS WROUGHT STEEL PIPE Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Customary Units Schedule No SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in 28 28 28 28 28.000 28.000 28.000 28.000 0.250 0.281 0.312 0.344 74.16 83.26 92.35 101.70 10 28 28 28 28 28.000 28.000 28.000 28.000 0.375 0.406 0.438 0.469 110.74 119.76 129.05 138.03 STD 28 28 28 28 28.000 28.000 28.000 28.000 0.500 0.562 0.625 0.688 146.99 164.84 182.90 200.87 XS 28 28 28 28 28 28.000 28.000 28.000 28.000 28.000 0.750 0.812 0.875 0.938 1.000 218.48 236.00 253.72 271.36 288.63 30 30 30 30 30.000 30.000 30.000 30.000 0.250 0.281 0.312 0.344 30 30 30 30 30.000 30.000 30.000 30.000 30 30 30 30 `,`,`,`,,`,`,,,`,``,`,,`,,-`-`,,`,,`,`,,` - Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] DN [Note (2)] Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m 700 700 700 700 711 711 711 711 6.35 7.14 7.92 8.74 110.35 123.94 137.32 151.37 700 700 700 700 711 711 711 711 9.53 10.31 11.13 11.91 164.86 178.16 192.10 205.34 20 30 700 700 700 700 711 711 711 711 12.70 14.27 15.88 17.48 218.71 245.19 272.23 298.96 700 700 700 700 700 711 711 711 711 711 19.05 20.62 22.23 23.83 25.40 325.08 351.07 377.60 403.84 429.46 79.51 89.27 99.02 109.06 10 750 750 750 750 762 762 762 762 6.35 7.14 7.92 8.74 118.34 132.92 147.29 162.36 0.375 0.406 0.438 0.469 118.76 128.44 138.42 148.06 STD 750 750 750 750 762 762 762 762 9.53 10.31 11.13 11.91 176.85 191.12 206.10 220.32 30.000 30.000 30.000 30.000 0.500 0.562 0.625 0.688 157.68 176.86 196.26 215.58 XS 20 30 750 750 750 750 762 762 762 762 12.70 14.27 15.88 17.48 234.68 263.14 292.20 320.95 30 30 30 30 30.000 30.000 30.000 30.000 0.750 0.812 0.875 0.938 234.51 253.36 272.43 291.41 750 750 750 750 762 762 762 762 19.05 20.62 22.23 23.83 349.04 377.01 405.56 433.81 30 30 30 30 30 30.000 30.000 30.000 30.000 30.000 1.000 1.062 1.125 1.188 1.250 310.01 328.53 347.26 365.90 384.17 750 750 750 750 750 762 762 762 762 762 25.40 26.97 28.58 30.18 31.75 461.41 488.88 516.93 544.68 571.79 32 32 32 32 32.000 32.000 32.000 32.000 0.250 0.281 0.312 0.344 84.85 95.28 105.69 116.41 10 800 800 800 800 813 813 813 813 6.35 7.14 7.92 8.74 126.32 141.90 157.25 173.35 32 32 32 32 32.000 32.000 32.000 32.000 0.375 0.406 0.438 0.469 126.78 137.12 147.78 158.08 STD 800 800 800 800 813 813 813 813 9.53 10.31 11.13 11.91 188.83 204.09 220.10 235.29 32 32 32 32 32.000 32.000 32.000 32.000 0.500 0.562 0.625 0.688 168.37 188.87 209.62 230.29 XS 20 30 40 800 800 800 800 813 813 813 813 12.70 14.27 15.88 17.48 250.65 281.09 312.17 342.94 12 WELDED AND SEAMLESS WROUGHT STEEL PIPE ASME B36.10M-2004 Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in 32 32 32 32 32.000 32.000 32.000 32.000 0.750 0.812 0.875 0.938 250.55 270.72 291.14 311.47 800 800 800 800 813 813 813 813 19.05 20.62 22.23 23.83 373.00 402.94 433.52 463.78 32 32 32 32 32 32.000 32.000 32.000 32.000 32.000 1.000 1.062 1.125 1.188 1.250 331.39 351.23 371.31 391.30 410.90 800 800 800 800 800 813 813 813 813 813 25.40 26.97 28.58 30.18 31.75 493.35 522.80 552.88 582.64 611.72 34 34 34 34 34.000 34.000 34.000 34.000 0.250 0.281 0.312 0.344 90.20 101.29 112.36 123.77 10 850 850 850 850 864 864 864 864 6.35 7.14 7.92 8.74 134.31 150.88 167.21 184.34 34 34 34 34 34.000 34.000 34.000 34.000 0.375 0.406 0.438 0.469 134.79 145.80 157.14 168.11 STD 850 850 850 850 864 864 864 864 9.53 10.31 11.13 11.91 200.82 217.06 234.10 250.27 34 34 34 34 34.000 34.000 34.000 34.000 0.500 0.562 0.625 0.688 179.06 200.89 222.99 245.00 XS 20 30 40 850 850 850 850 864 864 864 864 12.70 14.27 15.88 17.48 266.63 299.04 332.14 364.92 34 34 34 34 34.000 34.000 34.000 34.000 0.750 0.812 0.875 0.938 266.58 288.08 309.84 331.52 850 850 850 850 864 864 864 864 19.05 20.62 22.23 23.83 396.96 428.88 461.48 493.75 34 34 34 34 34 34.000 34.000 34.000 34.000 34.000 1.000 1.062 1.125 1.188 1.250 352.77 373.94 395.36 416.70 437.62 850 850 850 850 850 864 864 864 864 864 25.40 26.97 28.58 30.18 31.75 525.30 556.73 588.83 620.60 651.65 36 36 36 36 36.000 36.000 36.000 36.000 0.250 0.281 0.312 0.344 95.54 107.30 119.03 131.12 10 900 900 900 900 914 914 914 914 6.35 7.14 7.92 8.74 142.14 159.68 176.97 195.12 36 36 36 36 36.000 36.000 36.000 36.000 0.375 0.406 0.438 0.469 142.81 154.48 166.51 178.14 STD 900 900 900 900 914 914 914 914 9.53 10.31 11.13 11.91 212.57 229.77 247.82 264.96 36 36 36 36 36.000 36.000 36.000 36.000 0.500 0.562 0.625 0.688 189.75 212.90 236.35 259.71 XS 20 30 900 900 900 900 914 914 914 914 12.70 14.27 15.88 17.48 282.29 316.63 351.73 386.47 36 36 36 36 36.000 36.000 36.000 36.000 0.750 0.812 0.875 0.938 282.62 305.44 328.55 351.57 40 900 900 900 900 914 914 914 914 19.05 20.62 22.23 23.83 420.45 454.30 488.89 523.14 13 DN [Note (2)] Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m `,`,`,`,,`,`,,,`,``,`,,`,,-`-`,,`,,`,`,,` - Customary Units ASME B36.10M-2004 WELDED AND SEAMLESS WROUGHT STEEL PIPE Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Customary Units Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in 36 36 36 36 36 36.000 36.000 36.000 36.000 36.000 1.000 1.062 1.125 1.188 1.250 374.15 396.64 419.42 442.10 464.35 900 900 900 900 900 914 914 914 914 914 25.40 26.97 28.58 30.18 31.75 556.62 589.98 624.07 657.81 690.80 38 38 38 38 38.000 38.000 38.000 38.000 0.312 0.344 0.375 0.406 125.70 138.47 150.83 163.16 STD 950 950 950 950 965 965 965 965 7.92 8.74 9.53 10.31 186.94 206.11 224.56 242.74 38 38 38 38 38.000 38.000 38.000 38.000 0.438 0.469 0.500 0.562 175.87 188.17 200.44 224.92 XS 950 950 950 950 965 965 965 965 11.13 11.91 12.70 14.27 261.82 279.94 298.26 334.58 38 38 38 38 38.000 38.000 38.000 38.000 0.625 0.688 0.750 0.812 249.71 274.42 298.65 322.80 950 950 950 950 965 965 965 965 15.88 17.48 19.05 20.62 371.70 408.46 444.41 480.24 38 38 38 38 38.000 38.000 38.000 38.000 0.875 0.938 1.000 1.062 347.26 371.63 395.53 419.35 950 950 950 950 965 965 965 965 22.23 23.83 25.40 26.97 516.85 553.11 588.57 623.90 38 38 38 38.000 38.000 38.000 1.125 1.188 1.250 443.47 467.50 491.07 950 950 950 965 965 965 28.58 30.18 31.75 660.01 695.77 730.74 40 40 40 40 40.000 40.000 40.000 40.000 0.312 0.344 0.375 0.406 132.37 145.83 158.85 171.84 STD 000 000 000 000 016 016 016 016 7.92 8.74 9.53 10.31 196.90 217.11 236.54 255.71 40 40 40 40 40.000 40.000 40.000 40.000 0.438 0.469 0.500 0.562 185.24 198.19 211.13 236.93 XS 000 000 000 000 016 016 016 016 11.13 11.91 12.70 14.27 275.82 294.92 314.23 352.53 40 40 40 40 40.000 40.000 40.000 40.000 0.625 0.688 0.750 0.812 263.07 289.13 314.69 340.16 000 000 000 000 016 016 016 016 15.88 17.48 19.05 20.62 391.67 430.45 468.37 506.17 40 40 40 40 40.000 40.000 40.000 40.000 0.875 0.938 1.000 1.062 365.97 391.68 416.91 442.05 000 000 000 000 016 016 016 016 22.23 23.83 25.40 26.97 544.81 583.08 620.51 657.82 40 40 40 40.000 40.000 40.000 1.125 1.188 1.250 467.52 492.90 517.80 000 000 000 016 016 016 28.58 30.18 31.75 695.96 733.73 770.67 42 42 42 42 42.000 42.000 42.000 42.000 0.344 0.375 0.406 0.438 153.18 166.86 180.52 194.60 STD 050 050 050 050 067 067 067 067 8.74 9.53 10.31 11.13 228.10 248.53 268.67 289.82 `,`,`,`,,`,`,,,`,``,`,,`,,-`-`,,`,,`,`,,` 14 DN [Note (2)] Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m WELDED AND SEAMLESS WROUGHT STEEL PIPE ASME B36.10M-2004 Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Customary Units Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in 42 42 42 42 42.000 42.000 42.000 42.000 0.469 0.500 0.562 0.625 208.22 221.82 248.95 276.44 XS 050 050 050 050 067 067 067 067 11.91 12.70 14.27 15.88 309.90 330.21 370.48 411.64 42 42 42 42 42.000 42.000 42.000 42.000 0.688 0.750 0.812 0.875 303.84 330.72 357.52 384.67 050 050 050 050 067 067 067 067 17.48 19.05 20.62 22.23 452.43 492.33 532.11 572.77 42 42 42 42 42.000 42.000 42.000 42.000 0.938 1.000 1.062 1.125 411.74 438.29 464.76 491.57 050 050 050 050 067 067 067 067 23.83 25.40 26.97 28.58 613.05 652.46 691.75 731.91 42 42 42.000 42.000 1.188 1.250 518.30 544.52 050 050 067 067 30.18 31.75 771.69 810.60 44 44 44 44 44.000 44.000 44.000 44.000 0.344 0.375 0.406 0.438 160.54 174.88 189.20 203.97 STD 100 100 100 100 118 118 118 118 8.74 9.53 10.31 11.13 239.09 260.52 281.64 303.82 44 44 44 44 44.000 44.000 44.000 44.000 0.469 0.500 0.562 0.625 218.25 232.51 260.97 289.80 XS 100 100 100 100 118 118 118 118 11.91 12.70 14.27 15.88 324.88 346.18 388.42 431.62 44 44 44 44 44 44.000 44.000 44.000 44.000 44.000 0.688 0.750 0.812 0.875 0.938 318.55 346.76 374.88 403.38 431.79 100 100 100 100 100 118 118 118 118 118 17.48 19.05 20.62 22.23 23.83 474.42 516.29 558.04 600.73 643.03 44 44 44 44 44 44.000 44.000 44.000 44.000 44.000 1.000 1.062 1.125 1.188 1.250 459.67 487.47 515.63 543.70 571.25 100 100 100 100 100 118 118 118 118 118 25.40 26.97 28.58 30.18 31.75 684.41 725.67 767.85 809.65 850.54 46 46 46 46 46.000 46.000 46.000 46.000 0.344 0.375 0.406 0.438 167.89 182.90 197.88 213.33 STD 150 150 150 150 168 168 168 168 8.74 9.53 10.31 11.13 249.87 272.27 294.35 317.54 46 46 46 46 46.000 46.000 46.000 46.000 0.469 0.500 0.562 0.625 228.27 243.20 272.98 303.16 XS 150 150 150 150 168 168 168 168 11.91 12.70 14.27 15.88 339.56 361.84 406.02 451.20 46 46 46 46 46 46.000 46.000 46.000 46.000 46.000 0.688 0.750 0.812 0.875 0.938 333.26 362.79 392.24 422.09 451.85 150 150 150 150 150 168 168 168 168 168 17.48 19.05 20.62 22.23 23.83 495.97 539.78 583.47 628.14 672.41 46 46 46 46 46 46.000 46.000 46.000 46.000 46.000 1.000 1.062 1.125 1.188 1.250 481.05 510.17 539.68 569.10 597.97 150 150 150 150 150 168 168 168 168 168 25.40 26.97 28.58 30.18 31.75 715.73 758.92 803.09 846.86 889.69 15 DN [Note (2)] Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m ASME B36.10M-2004 WELDED AND SEAMLESS WROUGHT STEEL PIPE Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in 48 48 48 48 48.000 48.000 48.000 48.000 0.344 0.375 0.406 0.438 175.25 190.92 206.56 222.70 STD 200 200 200 200 219 219 219 219 8.74 9.53 10.31 11.13 260.86 284.25 307.32 331.54 48 48 48 48 48.000 48.000 48.000 48.000 0.469 0.500 0.562 0.625 238.30 253.89 285.00 316.52 XS 200 200 200 200 219 219 219 219 11.91 12.70 14.27 15.88 354.54 377.81 423.97 471.17 48 48 48 48 48 48.000 48.000 48.000 48.000 48.000 0.688 0.750 0.812 0.875 0.938 347.97 378.83 409.61 440.80 471.90 200 200 200 200 200 219 219 219 219 219 17.48 19.05 20.62 22.23 23.83 517.95 563.74 609.40 656.10 702.38 48 48 48 48 48 48.000 48.000 48.000 48.000 48.000 1.000 1.062 1.125 1.188 1.250 502.43 532.88 563.73 594.50 624.70 200 200 200 200 200 219 219 219 219 219 25.40 26.97 28.58 30.18 31.75 747.67 792.84 839.04 884.82 929.62 52 52 52 52 52.000 52.000 52.000 52.000 0.375 0.406 0.438 0.469 206.95 223.93 241.42 258.36 300 300 300 300 321 321 321 321 9.53 10.31 11.13 11.91 308.23 333.26 359.54 384.50 52 52 52 52 52.000 52.000 52.000 52.000 0.500 0.562 0.625 0.688 275.27 309.03 343.25 377.39 300 300 300 300 321 321 321 321 12.70 14.27 15.88 17.48 409.76 459.86 511.12 561.93 52 52 52 52 52.000 52.000 52.000 52.000 0.750 0.812 0.875 0.938 410.90 444.33 478.21 512.01 300 300 300 300 321 321 321 321 19.05 20.62 22.23 23.83 611.66 661.27 712.02 762.33 52 52 52 52 52 52.000 52.000 52.000 52.000 52.000 1.000 1.062 1.125 1.188 1.250 545.19 578.29 611.84 645.30 678.15 300 300 300 300 300 321 321 321 321 321 25.40 26.97 28.58 30.18 31.75 811.57 860.69 910.93 960.74 009.49 56 56 56 56 56.000 56.000 56.000 56.000 0.375 0.406 0.438 0.469 222.99 241.29 260.15 278.41 400 400 400 400 422 422 422 422 9.53 10.31 11.13 11.91 331.96 358.94 387.26 414.17 56 56 56 56 56.000 56.000 56.000 56.000 0.500 0.562 0.625 0.688 296.65 333.06 369.97 406.80 400 400 400 400 422 422 422 422 12.70 14.27 15.88 17.48 441.39 495.41 550.67 605.46 56 56 56 56 56.000 56.000 56.000 56.000 0.750 0.812 0.875 0.938 442.97 479.05 515.63 552.12 400 400 400 400 422 422 422 422 19.05 20.62 22.23 23.83 659.11 712.63 767.39 821.68 16 DN [Note (2)] Outside Diameter, mm Wall Thickness, mm Plain End Mass, kg/m `,`,`,`,,`,`,,,`,``,`,,`,,-`-`,,`,,`,`,,` - Customary Units WELDED AND SEAMLESS WROUGHT STEEL PIPE ASME B36.10M-2004 Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Customary Units Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No SI Units NPS [Note (1)] Outside Diameter, in Wall Thickness, in Wall Thickness, mm Plain End Mass, kg/m 56 56 56 56 56 56.000 56.000 56.000 56.000 56.000 1.000 1.062 1.125 1.188 1.250 587.95 623.70 659.94 696.10 731.60 400 400 400 400 400 422 422 422 422 422 25.40 26.97 28.58 30.18 31.75 874.83 927.86 982.12 035.91 088.57 60 60 60 60 60.000 60.000 60.000 60.000 0.375 0.406 0.438 0.469 239.02 258.65 278.88 298.47 500 500 500 500 524 524 524 524 9.53 10.31 11.13 11.91 355.94 384.87 415.26 444.13 60 60 60 60 60.000 60.000 60.000 60.000 0.500 0.562 0.625 0.688 318.03 357.09 396.70 436.22 500 500 500 500 524 524 524 524 12.70 14.27 15.88 17.48 473.34 531.30 590.62 649.44 60 60 60 60 60.000 60.000 60.000 60.000 0.750 0.812 0.875 0.938 475.04 513.77 553.04 592.23 500 500 500 500 524 524 524 524 19.05 20.62 22.23 23.83 707.03 764.50 823.31 881.63 60 60 60 60 60 60.000 60.000 60.000 60.000 60.000 1.000 1.062 1.125 1.188 1.250 630.71 669.11 708.05 746.90 785.05 500 500 500 500 500 524 524 524 524 524 25.40 26.97 28.58 30.18 31.75 938.73 995.71 054.01 111.83 168.44 64 64 64 64 64.000 64.000 64.000 64.000 0.375 0.406 0.438 0.469 255.06 276.01 297.61 318.52 600 600 600 600 626 626 626 626 9.53 10.31 11.13 11.91 379.91 410.81 443.25 474.09 64 64 64 64 64.000 64.000 64.000 64.000 0.500 0.562 0.625 0.688 339.41 381.12 423.42 465.64 600 600 600 600 626 626 626 626 12.70 14.27 15.88 17.48 505.29 567.20 630.56 693.41 64 64 64 64 64.000 64.000 64.000 64.000 0.750 0.812 0.875 0.938 507.11 548.49 590.46 632.34 600 600 600 600 626 626 626 626 19.05 20.62 22.23 23.83 754.95 816.37 879.23 941.57 64 64 64 64 64 64.000 64.000 64.000 64.000 64.000 1.000 1.062 1.125 1.188 1.250 673.47 714.52 756.15 797.69 838.50 600 600 600 600 600 626 626 626 626 626 25.40 26.97 28.58 30.18 31.75 002.62 063.55 125.90 187.74 248.30 68 68 68 68 68.000 68.000 68.000 68.000 0.469 0.500 0.562 0.625 338.57 360.79 405.15 450.15 700 700 700 700 727 727 727 727 11.91 12.70 14.27 15.88 503.75 536.92 602.74 670.12 68 68 68 68 68 68.000 68.000 68.000 68.000 68.000 0.688 0.750 0.812 0.875 0.938 495.06 539.18 583.21 627.87 672.45 700 700 700 700 700 727 727 727 727 727 17.48 19.05 20.62 22.23 23.83 736.95 802.40 867.73 934.60 000.92 17 DN [Note (2)] Outside Diameter, mm `,`,`,`,,`,`,,,`,``,`,,`,,-`-`,,`,,`,`,,` - ASME B36.10M-2004 WELDED AND SEAMLESS WROUGHT STEEL PIPE Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Customary Units Plain End Weight, lb/ft Identification [Standard (STD), Extra-Strong (XS), or Double Extra Strong (XXS)] Schedule No NPS [Note (1)] Outside Diameter, in Wall Thickness, in 68 68 68 68 68 68.000 68.000 68.000 68.000 68.000 1.000 1.062 1.125 1.188 1.250 716.23 759.93 804.26 848.49 891.95 700 700 700 700 700 72 72 72 72 72.000 72.000 72.000 72.000 0.500 0.562 0.625 0.688 382.17 429.18 476.87 524.48 72 72 72 72 72.000 72.000 72.000 72.000 0.750 0.812 0.875 0.938 571.25 617.93 665.29 712.55 72 72 72 72 72 72.000 72.000 72.000 72.000 72.000 1.000 1.062 1.125 1.188 1.250 758.99 805.34 852.36 899.29 945.40 76 76 76 76 76.000 76.000 76.000 76.000 0.500 0.562 0.625 0.688 76 76 76 76 76.000 76.000 76.000 76.000 76 76 76 76 76 SI Units Wall Thickness, mm Plain End Mass, kg/m 727 727 727 727 727 25.40 26.97 28.58 30.18 31.75 065.89 130.73 197.09 262.92 327.39 800 800 800 800 829 829 829 829 12.70 14.27 15.88 17.48 568.87 638.64 710.06 780.92 800 800 800 800 829 829 829 829 19.05 20.62 22.23 23.83 850.32 919.60 990.52 060.87 800 800 800 800 800 829 829 829 829 829 25.40 26.97 28.58 30.18 31.75 129.78 198.57 268.98 338.83 407.25 403.55 453.21 503.60 553.90 900 900 900 900 930 930 930 930 12.70 14.27 15.88 17.48 600.50 674.18 749.62 824.45 0.750 0.812 0.875 0.938 603.32 652.65 702.70 752.66 900 900 900 900 930 930 930 930 19.05 20.62 22.23 23.83 897.77 970.96 045.89 120.22 76.000 76.000 76.000 76.000 76.000 1.000 1.062 1.125 1.188 1.250 801.75 850.75 900.47 950.09 998.85 900 900 900 900 900 930 930 930 930 930 25.40 26.97 28.58 30.18 31.75 193.05 265.74 340.17 414.01 486.33 80 80 80 80 80.000 80.000 80.000 80.000 0.562 0.625 0.688 0.750 477.25 530.32 583.32 635.39 000 000 000 000 032 032 032 032 14.27 15.88 17.48 19.05 710.08 789.56 868.43 945.69 80 80 80 80 80 80 80 80 80.000 80.000 80.000 80.000 80.000 80.000 80.000 80.000 0.812 0.875 0.938 1.000 1.062 1.125 1.188 1.250 687.37 740.12 792.77 844.51 896.17 948.57 1,000.89 1,052.30 000 000 000 000 000 000 000 000 032 032 032 032 032 032 032 032 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75 022.83 101.81 180.17 256.94 333.59 412.06 489.92 566.20 DN [Note (2)] Outside Diameter, mm NOTES: (1) NPS (Nominal Pipe Size) is a dimensionless designator that has been substituted in the customary units section for the previous term Inch Nominal Size (2) DN (Nominal Diameter) is a dimensionless designator used in the SI (metric) system to describe pipe size (3) See ASME B16.11-2001, para 3.1 18 ASME B36.10M-2004 umentCopyright provided ASME by IHSInternational Licensee=Bureau Veritas/5959906001, 10/28/2004 16:59 MDT Provided Questions by IHSor under comments licenseabout with ASME this message: please call the Document cy Group at 303-397-2295 M03104 ... Mass, kg/m ASME B36.10M-2004 WELDED AND SEAMLESS WROUGHT STEEL PIPE Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Plain End Weight, lb/ft Identification [Standard... 342.94 12 WELDED AND SEAMLESS WROUGHT STEEL PIPE ASME B36.10M-2004 Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Plain End Weight, lb/ft Identification [Standard... Mass, kg/m ASME B36.10M-2004 WELDED AND SEAMLESS WROUGHT STEEL PIPE Table Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d) Plain End Weight, lb/ft Identification [Standard