This paper describes sensitive, accurate and precise spectrophotometric, TLC-spectrodensitometric and high performance liquid chromatographic (HPLC) methods for simultaneous determination of olanzapine and fluoxetine HCl. Two spectrophotometric methods were developed, namely; first derivative (D1 ) and derivative ratio (DD1 ) methods. The TLC method employed aluminum TLC plates precoated with silica gel GF254 as the stationary phase and methanol: toluene:ammonia (7:3:0.1, by volume) as the mobile phase, where the chromatogram was scanned at 235 nm. The developed HPLC method used a reversed phase C18 column with isocratic elution. The mobile phase composed of phosphate buffer pH 4.0:acetonitrile:triethylamine (53:47:0.03, by volume) at flow rate of 1.0 mL min1 . Quantitation was achieved with UV detection at 235 nm. The methods were validated according to the International Conference on Harmonization (ICH) guidelines. The selectivity of the proposed methods was tested using laboratory-prepared mixtures. The developed methods were successfully applied for the determination of olanzapine and fluoxetine HCl in bulk powder and combined capsule dosage form.
Journal of Advanced Research (2013) 4, 173–180 Cairo University Journal of Advanced Research ORIGINAL ARTICLE Simultaneous determination of olanzapine and fluoxetine hydrochloride in capsules by spectrophotometry, TLC-spectrodensitometry and HPLC Mahmoud A Tantawy *, Nagiba Y Hassan, Nariman A Elragehy, Mohamed Abdelkawy Analytical Chemistry Department, Faculty of Pharmacy, Cairo University, Kasr el Aini Street, 11562 Cairo, Egypt Received 10 April 2012; revised 18 May 2012; accepted 20 May 2012 Available online 23 June 2012 KEYWORDS Spectrophotometry; TLC-spectrodensitometry; HPLC; Olanzapine; Fluoxetine HCl Abstract This paper describes sensitive, accurate and precise spectrophotometric, TLC-spectrodensitometric and high performance liquid chromatographic (HPLC) methods for simultaneous determination of olanzapine and fluoxetine HCl Two spectrophotometric methods were developed, namely; first derivative (D1) and derivative ratio (DD1) methods The TLC method employed aluminum TLC plates precoated with silica gel GF254 as the stationary phase and methanol: toluene:ammonia (7:3:0.1, by volume) as the mobile phase, where the chromatogram was scanned at 235 nm The developed HPLC method used a reversed phase C18 column with isocratic elution The mobile phase composed of phosphate buffer pH 4.0:acetonitrile:triethylamine (53:47:0.03, by volume) at flow rate of 1.0 mL minÀ1 Quantitation was achieved with UV detection at 235 nm The methods were validated according to the International Conference on Harmonization (ICH) guidelines The selectivity of the proposed methods was tested using laboratory-prepared mixtures The developed methods were successfully applied for the determination of olanzapine and fluoxetine HCl in bulk powder and combined capsule dosage form ª 2012 Cairo University Production and hosting by Elsevier B.V All rights reserved Introduction Olanzapine (OLZ) is an atypical antipsychotic drug, approved by the FDA for the treatment of schizophrenia and bipolar * Corresponding author Tel.: +20 223639307; fax: +20 223628426 E-mail address: matantawy@hotmail.com (M.A Tantawy) Peer review under responsibility of Cairo University Production and hosting by Elsevier disorder It is chemically designated as 2-methyl-4-(4-methyl1-piperazinyl)-10H-thieno(2,3-b)(1,5)benzodiazepine, Fig 1A It has a higher affinity for 5-HT2 serotonin receptors than D2 dopamine receptors The mode of action of Olanzapine’s antipsychotic activity is unknown [1] Fluoxetine HCl (FLX) is an antidepressant of the selective serotonin reuptake inhibitor (SSRI) class It is chemically designated as N-methyl3-phenyl-3-[4-(trifluoromethyl)phenoxy]propan-1-amine, Fig 1B It is used for the treatment of depression Being one of SSRI drugs, it acts by increasing the extracellular level of the neurotransmitter serotonin by inhibiting its reuptake into the cell [1] 2090-1232 ª 2012 Cairo University Production and hosting by Elsevier B.V All rights reserved http://dx.doi.org/10.1016/j.jare.2012.05.004 174 M.A Tantawy et al CH3 N N N H N CH3 S (a) The structure of olanzapine C 17 H2O N S=312.4 F3C O CH CH2 CH2 NH CH3 (b) The structure of fluoxetine HCl C17 H18 F3 NO=309.3 Fig The structures of olanzapine and fluoxetine HCl Determination of OLZ was carried out by HPLC [2–6], UV spectrophotometry [2,7], CZE [2] and linear voltammetry [2] For FLX, it was determined by UV spectrophotometry [8– 10] and HPLC [11,12] There is no official method for the determination of OLZ and FLX in dosage form There are few reported methods for their simultaneous analysis including three HPLC methods [13–15] and two HPTLC methods [14,15] So, the aim of this work was to develop recent, simple, sensitive and validated spectrophotometric methods, TLC-spectrodensitometric method and HPLC chromatographic method for the simultaneous determination of OLZ and FLX in their pure powdered form, laboratory prepared mixtures and in their pharmaceutical capsule dosage form The spectrophotometric methods applied are first derivative (D1) and derivative ratio (DD1) method The developed methods can be successfully applied in routine analysis and quality control laboratories Experimental Apparatus Spectrophotometric measurements were carried out on a dual beam Shimadzu (Kyoto, Japan) UV–Vis spectrophotometer, model UV-1601 PC connected to IBM compatible with an Hp 600inkjet printer The bundle software, UV PC personal spectroscopy software version 3.7 (Shimadzu, Kyoto, Japan) was used to process absorption and derivative spectra, the spectral band width was nm and scanning speed was 2800 nm minÀ1 The TLC system comprised a Camag Linomat autosampler (Switzerland), Camag microsyringe (100-lL), and Camag TLC scanner 35/N/30319 with winCATS software, a short wavelength UV lamp emitting at 254 nm (Desaga,Germany) and TLC plates precoated with silica gel GF254 20 · 20 cm, 0.25 mm thickness (E Merck, Darmstadt, Germany) The HPLC system comprised an Agilent pump with different flow rates (model 1100 series, Agilent, USA), equipped with a variable wavelength detector and a 20-lL volume injection loop A Zorbax ODS (5 lm, 25 · 4.6 mm i.d.) column was used as stationary the phase The samples were injected with a 50-lL Hamilton analytical syringe Materials Pure samples Olanzapine and fluoxetine HCl were kindly supplied by Eli Lilly Company – Egypt Their purity was found to be 100.00% and 99.92% for OLZ and FLX, respectively according to a reported HPLC method [14] Pharmaceutical dosage form SymbyaxÒ (3 mg/25 mg) (Eli Lilly and Company – USA) Batch No A588272A, labeled to contain mg olanzapine and 25 mg fluoxetine HCl per capsule Simultaneous determination of olanzapine and fluoxetine hydrochloride in capsules 175 (a) Zero order absorption spectra of 7.5 µg mL-1 -1 olanzapine (- - -) and 200 µg mL fluoxetine HCl ( ) using methanol as a blank Fig TLC chromatogram of a resolved mixture of olanzapine (6 lg bandÀ1) and fluoxetine HCl (25 lg bandÀ1) (b) First derivative absorption spectra of 7.5 µg mL-1 -1 olanzapine (- - -) and 200 µg mL fluoxetine HCl ( ) using methanol as a blank Fig D0 and D1 Spectra of olanzapine and fluoxetine HCl Chemicals and reagents All chemicals used throughout the work were of analytical grade and solvents were of spectroscopic and HPLC grade: Methanol (Merck, Germany), acetonitrile (Merck, Germany), triethylamine (Sigma–Aldrich, Belgium), phosphate buffer solution pH 4.0 [16], toluene (Adwic, Egypt), ammonia solution 33% (Adwic, Egypt) and double distilled deionized water (Otsuka, Cairo, Egypt) Solutions Stock standard solutions Stock standard solutions of OLZ (4 mg mLÀ1) and FLX (20 mg mLÀ1) were prepared in methanol (a) First derivative of ratio spectra of olanzapine -1 -1 – 17.5 µg mL using the spectrum of 200 µg mL of fluoxetine HCl as a divisor, methanol was used as a blank Fig Working standard solutions For spectrophotometric methods Working solutions of OLZ (50 lg mLÀ1) and FLX (1 mg mLÀ1) were prepared from their respective stock solutions using methanol as a solvent For TLC-spectrodensitometric method Working solutions of OLZ (1 mg mLÀ1) and FLX (10 mg mLÀ1) were prepared from their respective stock solutions using methanol as a solvent For HPLC method Working solutions of OLZ (100 lg mLÀ1) and FLX (1 mg mLÀ1) were prepared from their respective stock solutions using methanol as a solvent Laboratory-prepared mixtures Solutions containing different ratios of OLZ and FLX were prepared by transferring aliquots from their working solutions into a series of 10-ml volumetric flasks and the volume of each was completed to the mark with methanol in case of spectrophotometry and TLC spectro-densitometry For HPLC, the volume was completed to the mark with the mobile phase (b) First derivative of ratio spectra of fluoxetine HCl 100 – 600 µg mL-1 using the spectrum of 12.5 µg mL-1 of olanzapine as a divisor, methanol was used as a blank DD1 spectra of olanzapine and fluoxetine HCl 176 M.A Tantawy et al spectra of 200 lg mLÀ1 FLX and 12.5 lg mLÀ1 OLZ, respectively The first derivative of the obtained spectra was recorded The peak amplitudes of the obtained DD1 spectra were measured at 270 nm for OLZ and at 278 nm for FLX For TLC-spectrodensitometric method Aliquots equivalent to 1–8 mg of OLZ and 10–60 mg of FLX were accurately measured and transferred from their working standard solutions into a set of 10-ml volumetric flasks and the volumes were completed to the mark with methanol A 10-lL aliquot of each solution was applied to the TLC plates, and the plates were developed to a distance of about 9.5 cm by the ascending technique using methanol: toluene: ammonia (7: 3: 0.1, by volume) as the mobile phase The plates were then removed, air-dried, and the spots were visualized under a UV lamp at 254 nm The chromatogram was scanned at 235 nm Two calibration curves representing the relationship between the recorded area under the peak and the corresponding concentrations of the drugs in micrograms per band were plotted Fig HPLC chromatogram of 30 lg mLÀ1 olanzapine and 500 lg mLÀ1 fluoxetine HCl Procedures Construction of the calibration curves For spectrophotometric method For D1 spectrophotometric method Aliquots equivalent to 50–175 lg of OLZ and 1000– 6000 lg of FLX were accurately measured and transferred from their working solutions into a set of 10-ml volumetric flasks and the volumes were completed to the mark with methanol The zero order and the first derivative spectra were recorded The peak amplitudes of the obtained first derivative spectra were measured at 292 nm for OLZ and at 270 nm for FLX For DD1 spectrophotometric method The zero order absorption spectra of OLZ (5–17.5 lg mLÀ1) and FLX (100– 600 lg mLÀ1) were measured and divided by the absorption Table Parameter For TLC-spectrodensitometric and HPLC methods The peak areas or peak area ratios of the laboratory-prepared mixtures OLZ D FLX TLC DD À1 5–17.5 lg mL À0.0261 0.1819 Intercept À0.0006 À0.0096 Mean of R (%) 99.98 100.04 SD of R (%) 0.828 0.608 Variance 0.686 0.370 Correlation coefficient (r) 0.9998 0.9999 Repeatabilityb (%) 0.500 0.721 Intermediate precisionb (%) 0.729 0.743 a Assay of laboratory-prepared mixtures For spectrophotometric methods The absorption spectra of the laboratory-prepared mixtures were scanned, processed as under calibration for each of the proposed methods and the concentration of OLZ and FLX in each mixture was calculated using the specified regression equation Assay parameters and validation sheet for determination of olanzapine and fluoxetine HCl by the proposed methods Range Slope For HPLC method Aliquots equivalent to 200–1000 lg of OLZ and 1000–6000 lg of FLX were accurately measured and transferred from their working solutions into a set of 10-ml volumetric flasks and the volumes were completed to the mark with the mobile phase [Phosphate buffer pH 4.0: acetonitrile: triethylamine (53:47:0.03, by volume)] A 20-lL aliquot of each solution was injected onto a Zorbax ODS column (5 lm, 250 · 4.6 mm i.d.), using the mobile phase, at flow rate 1.0 mL minÀ1 and detection at 235 nm Two calibration curves were constructed by plotting the peak area ratios, using 50 lg mLÀ1 of OLZ and 200 lg mLÀ1 of FLX as the external standards (the divisors), against the corresponding concentration of each drug in micrograms per milliliter D1 HPLC À1 À1 1–8 lg band 20–100 lg mL Slope 1a = À307.257 0.018 Slope 2a = 7226.1 1319.8 0.086 99.93 100.00 0.725 0.890 0.525 0.792 0.9999 0.9998 0.789 0.982 0.812 0.959 DD1 TLC 100–600 lg mLÀ1 10–60 lg bandÀ1 À0.0021 À0.0041 Slope 1a = À3.369 Slope 2a = 511.8 0.0066 À0.0593 7362.3 100.33 100.26 99.99 0.521 0.421 0.297 0.271 0.177 0.088 1.0000 0.9999 1.0000 0.252 0.431 0.151 0.270 0.404 0.162 HPLC 100–600 lg mLÀ1 0.005 À0.004 99.83 0.729 0.531 0.9999 0.511 0.533 Slope and are the coefficients of X2 and X, respectively Following a polynomial regression A = ax2 + bx + c Where, A is the integrated peak area, x is the concentration of Olanzapine or Fluoxetine (lg bandÀ1), a and b are coefficients and 2, respectively and c is the intercept b Average of three determinations 177 DD1 D1 DD1 17.5 12.0 05.0 17.5 10.0 100 100 100 200 100 99.95 100.60 99.96 100.67 100.20 100.00 100.45 100.60 100.30 100.00 101.05 100.88 100.60 100.70 100.65 99.20 99.99 100.42 99.70 99.65 100.28 0.344 100.27 0.268 100.78 0.186 Mean RSD FLX 99.79 0.451 Table Determination of olanzapine and fluoxetine HCl in laboratory prepared mixtures by TLC spectro-densitometric and HPLC methods OLZ: FLX OLZ FLX TLC HPLC TLC HPLC 3:25 1:2 1:3 1:4 98.83 99.00 99.00 99.20 100.63 100.78 100.66 100.64 99.76 99.90 100.23 100.05 99.76 98.65 99.43 100.36 Mean RSD 99.01 0.153 100.68 0.069 99.99 0.202 99.55 0.716 Average of five determinations D1 a FLX Mean ± RSD Recovery of standard addeda ± RSD OLZ OLZ HPLC TLC DD1 D1 FLX HPLC TLC DD1 D1 Concentration (lg mLÀ1) SymbyaxÒ B.N A588272A (3 mg OLZ & 25 mg FLX) per capsule OLZ Table Determination of olanzapine and fluoxetine HCl in laboratory prepared mixtures by spectrophotometric methods Determination of olanzapine and fluoxetine HCl in SymbyaxÒ capsules and application of standard addition technique using the proposed methods For TLC-spectrodensitometric and HPLC methods Forty capsules of SymbyaxÒ (3 mg/25 mg) were evacuated, accurately weighed and finely powdered Accurately weighed portions equivalent to 60 mg OLZ and 500 mg FLX respectively, were transferred into 100-mL beakers, sonicated in 30 mL methanol for 10 min, and filtered into 100-mL volumetric flasks The residues were washed three times each using 10 mL methanol and the solution was completed to the mark with the same solvent Aliquots of 5.0 mL were transferred from the prepared solutions to 10-mL volumetric flasks and diluted with methanol for TLC-spectrodensitometric determination of both drugs, Table Application to pharmaceutical preparations For spectrophotometric methods Twenty capsules of SymbyaxÒ (3 mg/25 mg) were evacuated, accurately weighed and finely powdered Accurately weighed portions equivalent to 12 mg OLZ and 100 mg FLX, respectively were transferred into 100-mL beakers, sonicated in 30 mL methanol for 10 and filtered into 100-mL volumetric flasks The residues were washed three times each using 10 mL methanol and the solution was completed to the mark with the same solvent Aliquots of 1.0 mL were transferred from the prepared solutions to 10-mL volumetric flasks and diluted with methanol for spectrophotometric determination of both drugs The general procedure previously described under each method was followed to determine the concentration of each drug in the prepared dosage form solutions a were scanned and processed as described for the calibration for each of the proposed TLC and HPLC methods, respectively The concentrations of OLZ and FLX in each mixture were calculated using the specified regression equations 99.65 ± 0.317 100.92 ± 0.019 98.99 ± 1.350 100.98 ± 0.210 100.33 ± 0.067 100.49 ± 0.112 101.07 ± 0.160 99.26 ± 0.370 100.55 ± 0.224 99.95 ± 0.743 99.51 ± 0.523 100.97 ± 0.510 99.81 ± 0.481 99.68 ± 0.246 100.44 ± 1.206 99.15 ± 0.229 Simultaneous determination of olanzapine and fluoxetine hydrochloride in capsules 178 M.A Tantawy et al where 10 lL was applied onto TLC plates For HPLC analysis, the last solution was further diluted by transferring 1.0 mL aliquots of it to 10-mL volumetric flasks and the volumes were completed with the HPLC mobile phase The general procedures described above for each method were followed to determine the concentration of OLZ and FLX in the prepared dosage form solutions scaling factor 10 and Dk = 4, Fig 3A and B The peak amplitudes showed good linearity and accuracy at 270 nm and 278 nm for OLZ and FLX, respectively The regression equations were computed for OLZ and FLX and found to be: DD1 ẳ 0:1819C 0:0096 for OLZị DD1 ¼ À0:0041C À 0:0593 ðfor FLXÞ where DD1 is the peak amplitude and C is the corresponding concentration in lg mLÀ1 Results and discussion Spectrophotometric methods First derivative method (D1) The zero order absorption spectra of OLZ and FLX show severe overlapping that prevents the use of direct spectrophotometry for their analysis without preliminary separation, Fig 2A In the first derivative spectrophotometry, the zero order absorption spectra of OLZ and FLX are obtained and then the first derivative of the obtained spectra was recorded using Dk = nm and a scaling factor of 10, Fig 2B The peak amplitudes of the obtained first derivative spectra were measured at 292 nm for OLZ and 270 for FLX The first derivative spectroscopy was applied to solve the problem of the overlapped absorption spectra of the cited drugs The regression equations were computed for OLZ and FLX and found to be: D ẳ 0:0261C 0:0006 for OLZị D1 ẳ 0:0021C þ 0:0066 ðfor FLXÞ TLC-spectrodensitometric method Several trials were done to choose a developing system which can separate OLZ from FLX Satisfactory separation was obtained using the system methanol: Toluene: ammonia (7:3:0.1, by volume) as the mobile phase Rf values were 0.3 ± 0.02 and 0.7 ± 0.02 for OLZ and FLX, respectively as shown in Fig This separation allows the determination of OLZ and FLX at 235 nm without any interference from each other A polynomial relationship was found to exist between the integrated area under the peak of the separated spots at the selected wavelength (235 nm) and the corresponding concentration of OLZ in the range of 1–8 lg bandÀ1 and in the range of 10– 60 lg bandÀ1 in case of FLX The regression equations were computed for OLZ and FLX and found to be: A ẳ 307:257C2 ỵ 7226:1C ỵ 1319:8 for OLZị A ẳ 3:369C2 ỵ 511:8C ỵ 7362:3 for FLXị where D1 is the peak amplitude and C is the corresponding concentration in lg mLÀ1 where A is the integrated peak area under the peak and C is the corresponding concentration in lg bandÀ1 Derivative ratio method (DD1) In the derivative ratio spectrophotometry, the absorption spectrum of the mixture is obtained and divided by the absorption spectrum of the standard solution of one of the components, and the first derivative of the ratio spectrum is obtained First derivative ratio spectrophotometric method DD1 was applied to solve the problem of the overlapped absorption spectra of the cited drugs Different concentrations of OLZ and FLX were investigated as divisors The divisor concentrations 12.5 lg mLÀ1 and 200 lg mLÀ1 of OLZ and FLX, respectively, were found the best regarding average recovery percent when they were used for the prediction of OLZ and FLX concentrations in bulk powder as well as in laboratory-prepared mixtures The obtained ratio spectra were differentiated with respect to wavelength using HPLC method Good chromatographic separation of the two drugs in their binary mixtures could be achieved by using a Zorbax ODS column (5 lm, 250 · 4.6 mm i.d.) with a mobile phase consisting of Phosphate buffer pH 4: acetonitrile: triethylamine (53:47:0.03, by volume) followed by UV detection at 235 nm, Fig Several trials have been undertaken to reach the optimum stationary/mobile phases matching The suggested chromatographic system allows complete base line separation at reasonable time The linearity of the detector’s response of the studied drugs was determined by plotting peak area ratios (calculated following the external standard technique using 50 lg mLÀ1 of OLZ and 200 lg mLÀ1 of FLX as the external standards) versus concentrations and linear correlation was obtained Table Parametrs required for system suitability test of TLC-spectrodensitometric and HPLC methods Parameters TLC OLZ Retention time (tR) [min.] Retardation factor (Rf) Resolution (Rs) Tailing factor (T) Capacity factor (K0 ) Selectivity factor (a) Column efficiency (N) Height equivalent to theoretical plate (HETP) (mm) HPLC FLX OLZ 2.74 0.30 0.833 0.70 3.56 0.714 0.9 2.053 2.333 2774.01 0.090 Reference values [18,19] FLX 9.77 12.88 1.1 8.743 4.259 2334.89 0.107 Rs > T = for a typical symmetric peak < K’ < 10 a>1 N > 2000 HPLC method using C-18 analytical column, acetonitrile: methanol: 0.032 M ammonium acetate buffer (45:05:50 by volume) as the mobile phase at flow rate 1.5 ml minÀ1 and detection at 235 nm b These values represent the corresponding tabulated values of t and F at p = 0.05 a 99.92 0.410 0.170 100.00 0.450 0.200 99.98 100.04 99.93 100.00 100.33 100.26 99.99 99.83 0.828 0.608 0.720 0.890 0.521 0.421 0.300 0.730 0.686 0.370 0.525 0.792 0.271 0.177 0.088 0.531 6 6 3.417 (5.05)b 1.847 (5.05)b 2.62 (5.05)b 3.96 (4.82)b 1.601 (5.05)b 1.045 (5.05)b 1.92 (4.39)b 3.13 (4.82)b 0.065 (2.23)b 0.126 (2.23)b 0.197 (2.23)b 0.007 (2.16)b 1.506 (2.23)b 1.422 (2.23)b 0.376 (2.20)b 0.260 (2.16)b Mean SD Variance n F-test Student’s ttest FLX OLZ D1 DD1 TLC HPLC D1 DD1 TLC HPLC ReportedaHPLC method [14] FLX OLZ Parameter Table Statistical comparison for the results obtained by the proposed methods and the reported method for the analysis of olanzapine and fluoxetine HCl Simultaneous determination of olanzapine and fluoxetine hydrochloride in capsules 179 The regression equations were computed for OLZ and FLX and found to be: A ẳ 0:018C ỵ 0:086 for OLZị A ¼ 0:005C À 0:004 ðfor FLXÞ where A is the peak area ratio and C is the corresponding concentration in lg mLÀ1 Validation of the proposed methods was done according to the ICH guidelines For all the proposed methods, the intermediate precision and repeatability, the assay parameters of the regression equations and the concentration ranges are shown in Table The proposed methods were successfully applied to the analysis of OLZ and FLX in their laboratory prepared mixtures, Tables and and in capsule dosage form, Table The validity of the proposed methods was assessed by applying the standard addition technique, Table After the proposed TLC-spectrodensitometric and HPLC methods have been validated, an overall system suitability testing was done to determine if the operating system is performing properly All peak parameters of resolution efficiency were calculated and satisfactory results were obtained, Table Statistical comparison between the results obtained by the proposed methods and those obtained by the reported HPLC method was done [14] The calculated t- and F-values [17] were found to be less than the corresponding theoretical ones, confirming good accuracy and excellent precision, Table Conclusion The proposed methods are simple, sensitive, and precise and could be easily applied in quality control laboratories for the simultaneous determination of OLZ and FLX The advantages of the proposed HPLC method over the reported ones [13–15] are better resolution (12.88), wider range (we can determine up to 100 lg mLÀ1 olanzapine and 600 lg mLÀ1 fluoxetine HCl) and less tailed (more symmetric) peaks The proposed TLC-spectrodensitometric method has also the advantages of better resolution and wider range (we can determine up to lg bandÀ1 olanzapine and 60 lg bandÀ1 fluoxetine HCl) over the reported ones [14,15] The proposed methods could be successfully applied for the routine analysis of the studied drugs either in their pure bulk powders or in their dosage forms without any preliminary separation step References [1] Moffat AC, Osselton MD, Widdop B Clarke’s analysis of drugs and poisons London: Pharmaceutical Press; 2004 [2] Raggi MA, Casamenti G, Mandrioli R, Izzo G, Kenndler E Quantitation of olanzapine in tablets by HPLZ, CZE, derivative spectrometry and linear voltammetry J Pharm Biomed Anal 2000;23(6):973–81 [3] Zhang G, Terry Jr AV, Bartlett MG Simultaneous determination of five antipsychotic drugs in rat plasma by high performance liquid chromatography with ultraviolet detection J Chromatogr B Analyt Technol Biomed Life Sci 2007;856(1–2):20–8 [4] D’Arrigo C, Migliardi G, Santoro V, Spina E Determination of olanzpine in plasma by reversed-phase high-performance 180 [5] [6] [7] [8] [9] [10] [11] M.A Tantawy et al liquid chromatography with ultraviolet detection Ther Drug Monit 2006;28(3):388–93 Dusci LJ, PeterHackett L, Fellows LM, Ilett KF Determination of Olanzapine in plasma by high-performance liquid chromatography using ultraviolet absorbance detection J Chromatogr B Analyt Technol Biomed Life Sci 2002;773(2):191–7 Olesen OV, Linnet K Determination of olanzapine in serum by high-performance liquid chromatography using ultraviolet detection considering the easy oxidability of the compound and the presence of other psychotropic drugs J Chromatogr B Biomed Sci Appl 1998;714(2):309–15 Krebs A, Starczewska B, Puzanowska-Tarasiewicz H, Sledz J Spectrophotometric determination of olanzapine by its oxidation with N-bromosuccinimide and cerium (IV) sulfate Anal Sci 2006;22(6):829–33 Afkhami A, Madrakian T, Khalafi L Spectrophotometric determination of fluoxetine by batch and flow injection methods Chem Pharm Bull (Tokyo) 2006;54(12):1642–6 Darwish IA Development and validation of spectrophotometric methods for determination of fluoxetine, sertraline, and paroxetine in pharmaceutical dosage forms J AOAC Int 2005;88(1):38–45 Prabhakar AH, Patel VB, Giridhar R Spectrophotometric determination of fluoxetine hydrochloride in bulk and in pharmaceutical formulations J Pharm Biomed Anal 1999;20(3):427–32 LLerena A, Dorado P, Berecz R, Gonza´lez A, Jesu´s Norberto M, de la Rubia A, et al Determination of fluoxetine and [12] [13] [14] [15] [16] [17] [18] [19] norfluoxetine in human plasma by high performance liquid chromatography with ultraviolet detection in psychiatric patients J Chromatogr B Analyt Technol Biomed Life Sci 2003;783(1):25–31 Zarghi A, Kebriaeezadeh A, Ahmadkhaniha R, Akhgari M, Rastkari N Selective liquid chromatographic method for determination of fluoxetine in plasma J AOAC Int 2001;84(6):1735–7 Pathak A, Rajput SJ Development of stability-indicating HPLC method for simultaneous determination of olanzapine and fluoxetine in combined dosage forms J Chromatogr Sci 2009;47(7):605–11 Patel S, Patel NJ Simultaneous RP-HPLC and HPTLC estimation of fluoxetine hydrochloride and olanzapine in tablet dosage forms Indian J Pharm Sci 2009;71(4):477–80 Shah Charmy R, Shah Nehal J, Suhagia Bhanubhai N, Patel Natvarlal M Simultaneous assay of olanzapine and fluoxetine in tablets by column high- performance liquid chromatography and high-performance thin layer chromatography J AOAC Int 2007;90(6):1573–8 Moffat AC, Osselton MD, Widdop B Clarke’s analysis of drugs and poisons London: Pharmaceutical Press; 2004, p 517 Spiegel MR, Stephns LJ Schaum outline of theory and problems of statistics New York: Schaum Outline Series; 1999 Andrea W, Phyllis R HPLC and CE principles and practice London: Academic Press; 1997, p 7–15 Adamovics AJ Chromatographic analysis of pharmaceuticals New York: Marcel Dekker; 1997, p 11–17 ... OLZ Table Determination of olanzapine and fluoxetine HCl in laboratory prepared mixtures by spectrophotometric methods Determination of olanzapine and fluoxetine HCl in SymbyaxÒ capsules and application... for determination of fluoxetine in plasma J AOAC Int 2001;84(6):1735–7 Pathak A, Rajput SJ Development of stability-indicating HPLC method for simultaneous determination of olanzapine and fluoxetine... analysis of olanzapine and fluoxetine HCl Simultaneous determination of olanzapine and fluoxetine hydrochloride in capsules 179 The regression equations were computed for OLZ and FLX and found to be: