biết cách nhận biết và so sánh giữa hai loại cáp RJ45 and RJ48 phục vụ cho việc nghiên cứu học tập và lắp đặt các loại thiết bị có sử dụng hai loại cáp này. người học có thể vận dụng từ đây vào trong thực tiễn sử dụng cũng như đáp ứng nhu cầu công việc
Difference Between RJ45 and RJ48 RJ45 vs RJ48 Most people can easily identify between an RJ11 and an RJ45 wiring, and point out the differences and specific uses of each But when it comes to an RJ45 and an RJ48, it becomes a little bit more difficult This is because they usually use the same modular connector and the differences between the two are not easily identifiable RJ which stands for registered jack does not actually identify the type of connector that is being used Instead, it identifies the wiring that is being used These two RJ types therefore differ only in how they are wired Both RJ48 and RJ45 use the 8P8C modular plug and pairs of the wires, one pair for transmitting and one pair for receiving data The RJ45 that we are already very familiar with uses the pins 1,2,3, and for receiving and transmitting data With RJ48, there are a few configurations that can be used depending on the situation and how they are to be used One configuration uses the pins 1,2,4, and while another uses 1,2,7, and Other wires are also used for extra shielding while the remaining wires are reserved in case some uses would arise in the future Both RJ48 and RJ45 use the 8P8C modular plug and pairs of the wires, one pair for transmitting and one pair for receiving data The RJ45 that we are already very familiar with uses the pins 1,2,3, and for receiving and transmitting data With RJ48, there are a few configurations that can be used depending on the situation and how they are to be used One configuration uses the pins 1,2,4, and while another uses 1,2,7, and Other wires are also used for extra shielding while the remaining wires are reserved in case some uses would arise in the future RJ45 is used mainly in local area networks where the distances between each network element is relatively short This is very common in a lot of offices and homes and is the main reason why it has become very popular RJ48 is used in other applications, the most common one would be in T1 data lines where the wires can extend longer distances and are often exposed to the environment To protect the integrity of the signal, RJ48 wirings use STP or Shielded Twisted Pair cables RJ45s use the more common UTP or Unshielded Twisted Pair that have categories to 6, with cat5e being the most Whether predominantly used RJ45 or RJ48 is to be used is dictated by the hardware It is no longer up to the consumer to choose Just make sure that you wire your connectors properly to what the hardware needs so that you have a working link Summary: 1.RJ45 and 2.RJ45 differs RJ48 from use RJ48 in the the same way they connector are wired 3.RJ45 is predominantly (phần lớn chủ yếu) used in LAN while RJ48 is more commonly seen on T1 4.RJ45 is connected with UTP cable while RJ48 uses STP lines ... Summary: 1 .RJ45 and 2 .RJ45 differs RJ48 from use RJ48 in the the same way they connector are wired 3 .RJ45 is predominantly (phần lớn chủ yếu) used in LAN while RJ48 is more commonly seen on T1 4 .RJ45. ..would arise in the future Both RJ48 and RJ45 use the 8P8C modular plug and pairs of the wires, one pair for transmitting and one pair for receiving data The RJ45 that we are already very familiar... where the distances between each network element is relatively short This is very common in a lot of offices and homes and is the main reason why it has become very popular RJ48 is used in other