DOI: 10.17073/2500-0632-2018-4-34-40 Nguyen Duyen Phong (Hanoi University of Mining and Geology, Hanoi, Vietnam) Dang Trung Thanh (Hanoi University of Mining and Geology, Hanoi, Vietnam) Tran Tuan Minh (Hanoi University of Mining and Geology, Hanoi, Vietnam) Nguyen Van Thinh (Hanoi University of Mining and Geology, Hanoi, Vietnam) Research design lining for utilities tunnel in the city based on state of "lining-massif soil" Nowaday, in order to resolve the problem of utilities tunnel in large cities is very necessary The technical pipelines, power cables, plumbing, drainage, in the large cities such as Hanoi, Ho Chi Minh is still a problem with no explanation Within the paper, the method to calculate the anti-tunnel structure of small tunnel by small tunneling machine In fact, due to the condition of the soil is not good and the limited construction conditions, it is necessary to calculate the composition of the tunnel for the tunnel For each area to ensure stability, aesthetics, economics, for the project Keywords: soil mass, tunnel lining, stress, calculation, elasticity theory, microtunneling, determination Introduction Microtunnelling is a special case of pipe jacking [5], where remote control of an automated microtunnel boring machine (MTBM) is employed Excavated soil is removed from the face of the pipe jacking shield or MTBM and transferred to the surface for disposal while the shield or MTBM and the product pipes to be installed are driven through the ground using the force developed by a jacking frame installed in a fixed shaft Pipe Jacking has been widely used for new pipeline installations [7] Application areas involve oil & gas, water supply, sewage, communication and electricity pipelines, and pipe-roof projects [9] Usually jacked pipes are glass Fibre Rein-forced plastic Mortar Pipes (FRMP), concrete pipes, clay pipes, cast ductile iron pipes, and steel pipes For shallow burial jacked pipes, the jacking load will control the cross-sectional design of the pipe, and the soil pressure may be insignificant However, for deep burial projects, high soil pressure may lead to the buckling of pipes [15], then the soil pressure becomes a crucial factor Soil pressure on jacked pipes was also invoked to estimate the jacking force [11] In current practices, the soil pressure on jacked pipes is estimated upon soil pressure models in Japan Microtunnelling Association (JMA), German standard ATV A 161 (ATV A 161), UK ‘Pipe Jacking Association’ (PJA), ASCE 27, and Chinese standard GB 50332 (GB 50332) [2, 6, 8, 12, 14] These soil pressure models are modified from one of Terzaghi arching models (termed Arching model I) [13] Basic theoretical principles The design of technical tunnels shall be arranged in areas of weak sediment, weak soil characteristics, which exist in the initial stress domain, causing gravity, hydrostatic pressure, etc The design of technical tunnels shall be arranged in areas of weak sediment, weak soil characteristics, which exist in the initial stress domain, causing gravity, hydrostatic pressure, etc.: (x0)(0) (y0)(0) H , (xy0)(0) 0, (1) where γ the average volume weight of soil, H depth of the development; "" sign is adopted in accordance with the rule of elasticity theory, according to which the compressive stresses are considered negative Application of the principle of superposition can simulate a full voltage in an massif soil of soil in a neighborhood devel- СТРОИТЕЛЬСТВО ГОРНЫХ ПРЕДПРИЯТИЙ И ОСВОЕНИЕ ГОРНОГО ПРОСТРАНСТВА 34 opment as the sum of the initial σ(0)(0) and additional σ(1)(0) (remove) the stresses caused by the formation of development Thus, we can write: σ(0)=σ(0)(0)+σ(1)(0), (2) where σ denotes all components of the stress tensor The concept of "removable stresses" was introduced by prof I.V Rodin [20] for simulating the formation of the production in a prestressed, massive massif of rocks Using this concept, it is easy to imagine that in the formation of a development its contour must be freed from the total normal and tangential stresses This can be achieved by superimposing stresses on the initial field around the generation of additional stresses of the same magnitude, but opposite in sign Physically, this means that the initial stresses acting on the contour of the future development must be "lifted" After installing the lining, which has a certain rigidity, depending on the thickness of the underground structure and the deformation properties of the material from which it is made, a redistribution of stresses occurs in the massif soil In this case, in the case when the lining is installed directly into the face immediately after opening the section of the mine, the removed (additional) stresses acting on the side of the massif soil are completely transferred to it as a load (radial pressure) The lining is included in the joint work with the massif soil as an integral element of the unified deformable system "lining-massif soil" The calculation scheme for determining the permissible displacements of the massif soil and stresses in the support is shown in Fig Having thus described the problem has an analytical solution presented, for example, in [16, 17] Following the provisions set out in the above-mentioned works, altering the way to solve this problem Assuming that development is not supported, then the contour L0 massif soil (area S0) boundary condition for the total stress in the polar coordinate system, taking into account the expressions (1), (2) can be written as: (r0 ) (r1)(0 ) (r0)(0) (r1)(0) H (3) Here, the shear stresses are not considered due to the axial symmetry of the problem Then, for the additional stress on contour unsupported produce the following relation: (r1)(0) H (4) Further, considering the case in which the development of the lining is installed, it should be noted that it prevents the free deformation contour L0 development, creating resistance For convenience, we consider the interaction of elements of a single system of "lining-massif soil", as shown in Fig Condition (4), taking into account the resistance lining takes the form: (r1)(0 ) H q0 q0 H , (5) where q0 resistance lining Fig Calculated scheme lining СТРОИТЕЛЬСТВО ГОРНЫХ ПРЕДПРИЯТИЙ И ОСВОЕНИЕ ГОРНОГО ПРОСТРАНСТВА 35 Fig The scheme of loading a single deformable system "lining-massif soil" In (5) accepted that the normal stresses acting in the direction to the contour L0 region S0, are compressed, ie negative The outer loop support (ring S1) having radial compressive stress q0, simulating mountain pressure on underground construction from the rock mass (the area S0) Neglecting the initial stresses in the lining, we write the expression for the additional radial stresses in the ring S1 in the contact line L0 with an massif soil: (r1)(1) q0 (6) In the case where the lining is mounted directly to the face output, the solution of the problem can be obtained using a known solution of the problem of Lame [21]: the plane strain thick-walled pipe, simulating lining, the condition that the radial displacement at the line of contact between the lining and the massif soil due to the action of additional stresses (5), (6), we obtain the equation with respect to the value of resistance to q0 Taking into account the direction of stresses, and by putting in the formula Lame outer tube radius r0 = ∞, the external pressure p0 = 0, we write the expression for the movement of an infinite medium (massif soil) on the contour L0: R u0 q0 H , (7) 2G0 where the notation: "−" sign in the expression (7) indicates that if the condition q0 ≤ γH point massif soil, located on the contour L0, shift into development G0 E0 mechanical characte21 rization of soil, called the shear modulus (8) Equation (7) can be represented in the form q0 = f(u0), that is, u 2G0 H u0 tg q0 H 1 R H 2G0 where tg R0 (9) This relation (9) in the mechanics of underground structures is called the equation of equilibrium states of soil mass, since it implies that each value of resistance support (pressure on the lining) corresponds to a certain amount of movement of the circuit section of development Further, the problem of putting in Lame outer tube radius r0 = R0, the external pressure p0 = q0, the inner radius r1 = R1, and the internal pressure of p1 = 0, we arrive to the second problem of plane deformation lining We write the expression for the radial displacements of points of the outer contour of the lining: R q u0 2 1 21 R02 R12 (10) 2G1 R0 R1 The sign in the expression (10) is selected for the same reasons as in the formula (7), i.e if q0 > point of the contour L0 moved inside the ring (lining) Equation (10) may also be present in the form q0 = f(u0), and is easy to see, this relationship is linear We represent it in the form of: СТРОИТЕЛЬСТВО ГОРНЫХ ПРЕДПРИЯТИЙ И ОСВОЕНИЕ ГОРНОГО ПРОСТРАНСТВА 36 q0 u0 tg , (11) where the notation: tg R02 R12 2G1 (12) R0 1 21 R02 R12 Equations (9) and (11) connect the same parameters q0 and u0 We construct the corresponding graphic dependences together in one drawing, as shown in Fig [1, 10] Fig Determination of the equilibrium state of a single deformable system "lining-massif soil" Fig line is a diagram of equilibrium states backed by generation, line diagram of equilibrium states lining Obviously, the point A of intersection of two charting will correspond to the equilibrium state of a single deformable "lining-massif soil" The value of q0 = P corresponds to the pressure on the lining (lining resist) with given geometrical and mechanical parameters set directly in the face, and the value of u0 = U displacement massif soil in these geological conditions The position of point A is determined by the combined solutions of equations (9) and (11): q0 H tg 1 tg R12 R02 H (13) R12 G0 R12 1 1 2 R0 R0 G1 Additional stress in the lining (which are at the same time complete, because no initial stresses) are determined by the formulas: - On the outer contour of the lining L0: 1 R12 1 R0 ( ex) (1) r q0 ; q0 ; (14) R12 1 R0 - Lining on the inner loop L1: (in ) q0 (15) R12 1 R0 The internal forces and bending moments in the lining of the radial sections are calculated from structural mechanics [18]: (in ) (ex) b; (in ) (ex) M b , 12 N (16) R where R0 R1 R0 1 the thick R0 ness of the lining, b = m Considering expressions (14)(15) of the formula (16) take the form: R2 12 qR R0 N 0 b ; R1 R0 q0 R02 R1 M b 12 R0 СТРОИТЕЛЬСТВО ГОРНЫХ ПРЕДПРИЯТИЙ И ОСВОЕНИЕ ГОРНОГО ПРОСТРАНСТВА (17) 37 where: Pu limit pressure that can withstand considered bolting without loss of bearing capacity Thus, the line in Fig characterizes the equilibrium state of the concrete lining, it should be limited to the point having ordinate q0 = Pu This means that the strength of the lining will be provided if the condition: P ≤ Pu (21) Significantly improve the static lining work is possible if it does not build directly at the bottom and install with some lag l0 from the bottom In this case, the diagram for the determination of the equilibrium state of the deformed system "lining-massif soil" is as shown in Fig Here, as before, a straight equilibrium states supported by the diagram generation, line diagram of equilibrium states lining, erected at a distance l0 from the bottom A point of intersection of the graph corresponds to the equilibrium state of a single deformable system "lining-massif soil" For comparison, a straight (dotted line) shows a diagram of equilibrium states lining being built directly at the bottom and a point B appropriate occasion equilibrium Offset massif soil u(l0), is implemented to the construction of the lining in the process of promoting the slaughter at a distance l0, characterized by the segment OO* The expression (17) allows you to test the strength of the lining Suppose, for example, the lining is made of concrete, which compressive strength is characterized by calculated resistance Rb Conditions strength bolting written in the form [18]: N NS , (18) where N the calculated normal force, which is determined from the first equation (17), NS limit bearing capacity of the radial section of the lining, which is determined 2e by the relation NS kRb b1 , in which k , e0 M N the eccentricity of the application of the longitudinal force Using expressions (17), we write 2e NS kRb b1 R2 4 12 R0 R (19) kRb R0 1 R R 3 R02 Then the condition of the strength of the lining of sections (18) takes the form R12 R2 1 12 R0 8kRb R0 Pu q0 3b R2 12 R0 (20) q H B A P* P F u0 0* E D u(l0 ) u( ) Fig Determination of the equilibrium state of geomechanical system "lining-massif soil" in the construction of the lining at a distance from the bottom l0 СТРОИТЕЛЬСТВО ГОРНЫХ ПРЕДПРИЯТИЙ И ОСВОЕНИЕ ГОРНОГО ПРОСТРАНСТВА 38 If development is unsupported for a long time (the lining is installed at a considerable distance from the bottom when l0→∞), all the possible displacement of the massif soil at this time and realized OF interval corresponds to a shift in the development of unsupported, that is, u(∞) = γHR0/2G0 From Fig that the construction of the lining of the backlog of slaughter generation leads to a reduction of pressure on the lining, ie the condition P ≤ P* The mechanics of underground structures [3] to account for this effect using the ratio: P=P*α* or α*=P/P* (22) Considering the similar triangles AEF and OBF, O*AD and OBE in Fig 4, can be written: P AD O * A OF OO * * P * BE OB OF u u l0 u l f l0 , (23) u u where u l u l0 R H f l0 , u 2G0 u R0 H 2G0 the bias circuit output, results from the decision of the respective plane problem for unsupported holes To determine the value of u(l0) should be considered three-dimensional picture surface deformations develop near the wellbore Research related to finding the displacement contour generation, depending on the distance to the bottom, in a large number of works, among which are the works of N.A Davydov [19] and M Baudendistel [4] Deciding the proper task of the theory of elasticity in the volume setting using numerical methods such as finite element method, each of the authors offered their own formula for determining the value of f(l0) Using a concrete representation for f(l0), being the substituted into the expres- sion (23), arrive at the appropriate formulas for the calculation of the correction factor α* So, based on the results Baudendistela M., prof N.S Bulichev a result of the correlation analysis between the values of the ratio α* and the relative distance l0/R0 to slaughter generate suggested the use of the exponential dependence of [17] 1, 75 R0 (24) * 0,64 e Due to the linear nature of the problem, in geomechanics accepted accounting backlog of construction of the lining of the slaughter carried out by adjusting the initial stress field (1) intact massif soil Then the corresponding components of the initial field multiplied by the value of α*, hence the initial stresses are determined by the formulas: l (x0)(0) (y0)(0) H *, (xy0)(0) (25) Conclusion From the obtained ratio can be important from a practical standpoint conclusions: For example, from formula (16) that with decreasing thickness of the lining R R0 R1 R0 1 pressure on it is R0 reduced, and at R1 R0 the pressure is absent, that is, q0→0 In very soft ground, when the condition G1>>G0 (G1 the shear modulus of the material lining) and can take G0/G1→0, the pressure q0 in the lining tends to the value of the initial stress in the rock mass in its natural state, e.g q0→γH References Alexandr A Pankratenko, Nguyen Quang Huy, Nguyen Duyen Phong, Andrey S Samal, Abdrahman B Begalinov, Dikhan B., 2016 Amantolov Influence of pipe ramming on stress state of surrounding soil and nearby tunnel lining Applied Mechanics and Materials, 843, pp 81-86 ASCE, 2001 27-00 Standard Practice for Direct Design of Precast Concrete Pipe for Jacking СТРОИТЕЛЬСТВО ГОРНЫХ ПРЕДПРИЯТИЙ И ОСВОЕНИЕ ГОРНОГО ПРОСТРАНСТВА 39 in Trenchless Construction Reston, Virginia, pp 8-9 ASTM, 2011 F 1962-11 Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit under Obstacles Including River Crossings West Conshohocken, PA, pp 15-16 Baudendistel M., 1979 Zum Entwurf von Tunnellen mit grossen Ausbruchsquerschnitt Rock Mechanics Suppl № 8, pp 95-100 Ciaran C Reilly, Trevor L.L Orr, 2017 Physical modelling of the effect of lubricants in pipe jacking Tunnelling and Underground Space Technology 63, pp 44-53 German ATV rules and standards, 1990 ATV-A 161 E-90 Structural calculation of driven pipes Hennef, pp 18-20 Haifeng Zhang, Peng Zhang, Wei Zhou, Shun Dong, Baosong Ma, 2016 A new model to predict soil pressure acting on deep burial jacked pipes Tunnelling and Underground Space Technology 60, pp 183-196 Japan Microtunnelling Association, 2013 Microtunnelling methods seriousⅡ.design, construction management and rudiments Tokyo, pp 69-72 Ma, B., Najafi, M Development and applications of trenchless technology in China Tunnell Undergr Space Technol., 2008, 23 (4), pp 476480 10 Nguyen Duyen Phong Elastic-plastic model of the massif, which takes into account the change in the strength of the rock in the formation of workings for calculating the fastenings of the subway under difficult mining and geological conditions Mining information and analytical bulletin, 2016, no 6, pp 241-250 11 Pellet-Beaucour A.L., Kastner R., 2002 Experimental and analytical study of friction forces during microtunneling operations Tunnell Undergr Space Technol 17 (1), pp 83-97 12 Pipe Jacking Association, 1995 Guide to best practice for the installation of pipe jacks and microtunnels London, pp 47-48 13 Terzaghi K., 1943 Theoretical Soil Mechanics John Wiley & Sons Inc, New York, USA, pp 66-76 14 The Ministry of Construction of China, 2002 GB 50332-02, Structural design code for pipeline of water supply and waste water engineering Beijing, pp 11-12 15 Zhen L., Chen J.J., Qiao P., Wang J.H., 2014 Analysis and remedial treatment of a steel pipe-jacking accident in complex underground environment Eng Struct 59, pp 210-219 16 Baklashov I.V., Kartoziya B.A Mekhanika podzemnykh sooruzheniy i konstruktsii krepey M.: Nedra, 1984 324 p 17 Bulychev N.S Mekhanika podzemnykh sooruzheniy: Ucheb dlya vuzov 2-e izd., pererab i dop M.: Nedra, 1994 382 p 18 VNIMI, VNIIOMShS Minugleproma SSSR Rukovodstvo po proektirovaniyu podzemnykh gornykh vyrabotok i raschetu krepi M.: Stroyizdat, 1983 273 p 19 Davydova N.A Priblizhennoe reshenie zadachi o smeshcheniyakh poverkhnosti beskonechnoy tsilindricheskoy polosti, zagruzhennoy zhestkim kol'tsevym shtampom konechnoy dliny FTPRPI, 1968 № Pp 111-117 20 Rodin I.V Snimaemaya nagruzka i gornoe davlenie Issledovaniya gornogo davleniya M.: Gosgortekhizdat, 1960 Pp 343-374 21 Samul' V.I Osnovy teorii uprugosti i plastichnosti: Ucheb Posobie dlya studentov vuzov M.: Vyssh shk., 1982 – 264 p “Gornye nauki i tehnologii”/ “Mining science and technology”, 2018, No 4, pp 34-40 Название: Аннотация: Ключевые слова: Метод расчета коммуникационных тоннелей в черте города на основе взаимодействия «футеровка-массив грунта» В настоящее время перед мегаполисами остро стоит проблема строительства тоннелей для прокладки коммуникаций В таких больших городах, как Ханой, Хошимин, до сих пор остаются без решения проблемы прокладки технических трубопроводов, силовых кабелей, водопровода, канализации Статья описывает метод расчета прокладки коммуникационных тоннелей, учитывающий состав грунта и ограниченные условия строительства для каждой конкретной области, с помощью небольшой туннельной бурильной машины Использование данного метода обеспечивает надежность и экономическую целесообразность проекта строительства масса грунта, прокладка тоннеля, напряжение, расчет, теория упругости, микротоннелирование СТРОИТЕЛЬСТВО ГОРНЫХ ПРЕДПРИЯТИЙ И ОСВОЕНИЕ ГОРНОГО ПРОСТРАНСТВА 40 ... generation, line diagram of equilibrium states lining Obviously, the point A of intersection of two charting will correspond to the equilibrium state of a single deformable "lining- massif soil" The. .. on underground construction from the rock mass (the area S0) Neglecting the initial stresses in the lining, we write the expression for the additional radial stresses in the ring S1 in the contact... convenience, we consider the interaction of elements of a single system of "lining- massif soil" , as shown in Fig Condition (4), taking into account the resistance lining takes the form: (r1)(0