Tiêu chuẩn ACI 318-99 cấu kiện bê tông.
BUILDING CODE REQUIREMENTS FOR STRUCTURAL CONCRETE (ACI 318-99) AND COMMENTARY (ACI 318R-99) REPORTED BY ACI COMMITTEE 318 ACI Committee 318 Standard Building Code James R Cagley Chairman Craig E Barnes Florian G Barth Roger J Becker John E Breen Anthony P Chrest W Gene Corley Robert A Epifano Catherine W French Luis E Garcia Basile G Rabbat Secretary S K Ghosh Hershell Gill David P Gustafson James R Harris Neil M Hawkins C Raymond Hays Richard E Holguin Phillip J Iverson James O Jirsa Gary J Klein Cary S Kopczynski James Lefter H S Lew James G MacGregor John A Martin, Jr Leslie D Martin Robert F Mast Richard C Meininger Jack P Moehle Walter P Moore, Jr.* Glen M Ross Charles G Salmon Mete A Sozen Dean E Stephan Richard A Vognild Joel S Weinstein James K Wight Loring A Wyllie, Jr * Deceased Voting Subcommittee Members Kenneth B Bondy Ronald A Cook Richard W Furlong William L Gamble Roger Green D Kirk Harman Terence C Holland Kenneth C Hover Michael E Kreger LeRoy A Lutz Joe Maffei Steven L McCabe Gerard J McGuire Peter Meza Denis Mitchell Randall W Poston Julio A Ramirez Gajanan M Sabnis John R Salmons Thomas C Schaeffer Stephen J Seguirant Roberto Stark Maher K Tadros John W Wallace Sharon L Wood Consulting Members Richard D Gaynor Jacob S Grossman John M Hanson Edward S Hoffman Francis J Jacques Alan H Mattock Richard A Ramsey Irwin J Speyer INTRODUCTION 318/318R-1 BUILDING CODE REQUIREMENTS FOR STRUCTURAL CONCRETE (ACI 318-99) AND COMMENTARY (ACI 318R-99) REPORTED BY ACI COMMITTEE 318 The code portion of this document covers the proper design and construction of buildings of structural concrete The code has been written in such form that it may be adopted by reference in a general building code and earlier editions have been widely used in this manner Among the subjects covered are: drawings and specifications; inspection; materials; durability requirements; concrete quality, mixing, and placing; formwork; embedded pipes; and construction joints; reinforcement details; analysis and design; strength and serviceability; flexural and axial loads; shear and torsion; development and splices of reinforcement; slab systems; walls; footings; precast concrete; composite flexural members; prestressed concrete; shells and folded plate members; strength evaluation of existing structures; special provisions for seismic design; structural plain concrete; an alternate design method in Appendix A; unified design provisions in Appendix B; and alternative load and strength reduction factors in Appendix C The quality and testing of materials used in construction are covered by reference to the appropriate ASTM standard specifications Welding of reinforcement is covered by reference to the appropriate ANSI/AWS standard Because the ACI Building Code is written as a legal document so that it may be adopted by reference in a general building code, it cannot present background details or suggestions for carrying out its requirements or intent It is the function of this commentary to fill this need The commentary discusses some of the considerations of the committee in developing the code with emphasis given to the explanation of new or revised provisions that may be unfamiliar to code users References to much of the research data referred to in preparing the code are cited for the user desiring to study individual questions in greater detail Other documents that provide suggestions for carrying out the requirements of the code are also cited Keywords: admixtures; aggregates; anchorage (structural); beam-column frame; beams (supports); building codes; cements; cold weather construction; columns (supports); combined stress; composite construction (concrete and steel); composite construction (concrete to concrete); compressive strength; concrete construction; concretes; concrete slabs; construction joints; continuity (structural); contraction joints; cover; curing; deep beams; deflections; drawings; earthquake resistant structures; embedded service ducts; flexural strength; floors; folded plates; footings; formwork (construction); frames; hot weather construction; inspection; isolation joints; joints (junctions); joists; lightweight concretes; loads (forces); load tests (structural); materials; mixing; mix proportioning; modulus of elasticity; moments; pipe columns; pipes (tubing); placing; plain concrete; precast concrete; prestressed concrete; prestressing steels; quality control; reinforced concrete; reinforcing steels; roofs; serviceability; shear strength; shearwalls; shells (structural forms); spans; specifications; splicing; strength; strength analysis; stresses; structural analysis; structural concrete; structural design; structural integrity; T-beams, torsion; walls; water; welded wire fabric ACI 318-99 was adopted as a standard of the American Concrete Institute March 18, 1999 to supersede ACI 318-95 in accordance with the Institute’s standardization procedure Vertical lines in the margins indicate the 1999 code and commentary changes A complete metric companion to ACI 318/318R has been developed, 318M/318RM; therefore no metric equivalents are included in this document ACI Committee Reports, Guides, Standard Practices, and Commentaries are intended for guidance in planning, designing, executing, and inspecting construction This Commentary is intended for the use of individuals who are competent to evaluate the significance and limitations of its content and recommendations and who will accept responsibility for the application of the material it contains The American Concrete Institute disclaims any and all responsibility for the stated principles The Institute shall not be liable for any loss or damage arising therefrom Reference to this commentary shall not be made in contract documents If items found in this Commentary are desired by the Architect/Engineer to be a part of the contract documents, they shall be restated in mandatory language for incorportation by the Architect/ Engineer Copyright 1999, American Concrete Institute All rights reserved including rights of reproduction and use in any form or by any means, including the making of copies by any photo process, or by any electronic or mechanical device, printed or written or oral, or recording for sound or visual reproduction or for use in any knowledge or retrieval system or device, unless permission in writing is obtained from the copyright proprietors ACI 318 Building Code and Commentary 318/318R-2 INTRODUCTION The 1999 ACI Building Code and Commentary are presented in a side-by-side column format, with code text placed in the left column and the corresponding commentary text aligned in the right column To further distinguish the Code from the Commentary, the Code has been printed in Helvetica, the same type face in which this paragraph is set Vertical lines in the margins indicate changes from ACI 318-95 This paragraph is set in Times Roman, and all portions of the text exclusive to the Commentary are printed in this type face Commentary section numbers are preceded by an “R” to further distinguish them from Code section numbers necessary to protect the public as stated in the code However, lower standards are not permitted INTRODUCTION This commentary discusses some of the considerations of Committee 318 in developing the provisions contained in “Building Code Requirements for Structural Concrete (ACI 318-99),” hereinafter called the code or the 1999 code Emphasis is given to the explanation of new or revised provisions that may be unfamiliar to code users In addition, comments are included for some items contained in previous editions of the code to make the present commentary independent of the commentary for ACI 318-95 Comments on specific provisions are made under the corresponding chapter and section numbers of the code The commentary is not intended to provide a complete historical background concerning the development of the ACI Building Code,* nor is it intended to provide a detailed résumé of the studies and research data reviewed by the committee in formulating the provisions of the code However, references to some of the research data are provided for those who wish to study the background material in depth As the name implies, “Building Code Requirements for Structural Concrete (ACI 318-99)” is meant to be used as part of a legally adopted building code and as such must differ in form and substance from documents that provide detailed specifications, recommended practice, complete design procedures, or design aids The code is intended to cover all buildings of the usual types, both large and small Requirements more stringent than the code provisions may be desirable for unusual construction The code and commentary cannot replace sound engineering knowledge, experience, and judgement A building code states only the minimum requirements necessary to provide for public health and safety The code is based on this principle For any structure, the owner or the structural designer may require the quality of materials and construction to be higher than the minimum requirements * For a history of the ACI Building Code see Kerekes, Frank, and Reid, Harold B., Jr., “Fifty Years of Development in Building Code Requirements for Reinforced Concrete,” ACI JOURNAL, Proceedings V 50, No 6, Feb 1954, p 441 For a discussion of code philosophy, see Siess, Chester P., “Research, Building Codes, and Engineering Practice,” ACI JOURNAL, Proceedings V 56, No 5, May 1960, p 1105 The commentary directs attention to other documents that provide suggestions for carrying out the requirements and intent of the code However, those documents and the commentary are not a part of the code The code has no legal status unless it is adopted by the government bodies having the police power to regulate building design and construction Where the code has not been adopted, it may serve as a reference to good practice even though it has no legal status The code provides a means of establishing minimum standards for acceptance of designs and construction by a legally appointed building official or his designated representatives The code and commentary are not intended for use in settling disputes between the owner, engineer, architect, contractor, or their agents, subcontractors, material suppliers, or testing agencies Therefore, the code cannot define the contract responsibility of each of the parties in usual construction General references requiring compliance with the code in the job specifications should be avoided since the contractor is rarely in a position to accept responsibility for design details or construction requirements that depend on a detailed knowledge of the design Generally, the drawings, specifications and contract documents should contain all of the necessary requirements to ensure compliance with the code In part, this can be accomplished by reference to specific code sections in the job specifications Other ACI publications, such as “Specifications for Structural Concrete for Buildings” (ACI 301) are written specifically for use as contract documents for construction Committee 318 recognizes the desirability of standards of performance for individual parties involved in the contract documents Available for this purpose are the plant certification programs of the Precast/Prestressed Concrete Institute, the Post-Tensioning Institute and the National Ready Mixed Concrete Association, and the Concrete Reinforcing Steel Institute’s Voluntary Certification Program for FusionBonded Epoxy Coating Applicator Plants In addition, “Recommended Practice for Inspection and Testing Agencies for Concrete, Steel, and Bituminous Materials As Used in Construction” (ASTM E 329-77) recommends performance requirements for inspection and testing agencies ACI 318 Building Code and Commentary INTRODUCTION Design reference materials illustrating applications of the code requirements may be found in the following documents The design aids listed may be obtained from the sponsoring organization Design aids: “ACI Design Handbook,” ACI Committee 340, Publication SP-17(97), American Concrete Institute, Farmington Hills, MI, 1997, 482 pp (Provides tables and charts for design of eccentricity loaded columns by the Strength Design Method Provides design aids for use in the engineering design and analysis of reinforced concrete slab systems carrying loads by two-way action Design aids are also provided for the selection of slab thickness and for reinforcement required to control deformation and assure adequate shear and flexural strengths.) “ACI Detailing Manual—1994,” ACI Committee 315, Publication SP-66(94), American Concrete Institute, Farmington Hills, MI, 1994, 244 pp (Includes the standard, ACI 315-92, and report, ACI 315R-94 Provides recommended methods and standards for preparing engineering drawings, typical details, and drawings placing reinforcing steel in reinforced concrete structures Separate sections define responsibilities of both engineer and reinforcing bar detailer.) CRSI Handbook, Concrete Reinforcing Steel Institute, Schaumburg, Ill., 8th Edition, 1996, 960 pp (Provides tabulated designs for structural elements and slab systems Design examples are provided to show the basis of and use of the load tables Tabulated designs are given for beams; square, round and rectangular columns; one-way slabs; and one-way joist construction The design tables for two-way slab systems include flat plates, flat slabs and waffle slabs The chapters on foundations provide design tables for square footings, pile caps, drilled piers (caissons) and cantilevered retaining walls Other design aids are presented for crack control; and development of reinforcement and lap splices.) “Reinforcement Anchorages and Splices,” Concrete Reinforcing Steel Institute, Schaumberg, Ill., 4th Edition, 1997, 100 pp (Provides accepted practices in splicing reinforcement The use of lap splices, mechanical splices, and welded splices are described Design data are presented for development and lap splicing of reinforcement.) “Structural Welded Wire Reinforcement Manual of Standard Practice,” Wire Reinforcement Institute, Findlay, 318/318R-3 Ohio, 4th Edition, Apr 1992, 31 pp (Describes wire fabric material, gives nomenclature and wire size and weight tables Lists specifications and properties and manufacturing limitations Book has latest code requirements as code affects welded wire Also gives development length and splice length tables Manual contains customary units and soft metric units.) “Structural Welded Wire Fabric Detailing Manual,” Wire Reinforcement Institute, McLean Va., 1st Edition, 1983, 76 pp (Provides information on detailing welded wire fabric reinforcement systems Includes design aids for welded wire fabric in accordance with ACI 318 Building Code requirements for wire fabric.) “Strength Design of Reinforced Concrete Columns,” Portland Cement Association, Skokie, Ill., EB009D, 1978, 48 pp (Provides design tables of column strength in terms of load in kips versus moment in ft-kips for concrete strength of 5000 psi and Grade 60 reinforcement Design examples are included Note that the PCA design tables not include the strength reduction factor φ in the tabulated values; Mu/φ and Pu/φ must be used when designing with this aid “PCI Design Handbook—Precast and Prestressed Concrete,” Precast/Prestressed Concrete Institute, Chicago, 5th Edition, 1999, 630 pp (Provides load tables for common industry products, and procedures for design and analysis of precast and prestressed elements and structures composed of these elements Provides design aids and examples.) “Design and Typical Details of Connections for Precast and Prestressed Concrete,” Precast/Prestressed Concrete Institute, Chicago, 2nd Edition, 1988, 270 pp (Updates available information on design of connections for both structural and architectural products, and presents a full spectrum of typical details Provides design aids and examples.) “PTI Post-Tensioning Manual,” Post-Tensioning Institute, Phoenix, 5th Edition, 1990, 406 pp (Provides comprehensive coverage of post-tensioning systems, specifications, and design aid construction concepts.) “PTI Design of Post-Tensioned Slabs,” Post-Tensioning Institute, Phoenix, 2nd Edition, Apr 1984, 56 pp (Illustrates application of the code requirements for design of one-way and two-way post-tensioned slabs Detailed design examples are presented.) ACI 318 Building Code and Commentary 318/318R-4 TABLE OF CONTENTS CONTENTS PART 1—GENERAL CHAPTER 1—GENERAL REQUIREMENTS 318-9 1.1—Scope 1.2—Drawings and specifications 1.3—Inspection 1.4—Approval of special systems of design or construction CHAPTER 2—DEFINITIONS 318-17 PART 2—STANDARDS FOR TESTS AND MATERIALS CHAPTER 3—MATERIALS 318-23 3.5—Steel reinforcement 3.6—Admixtures 3.7—Storage of materials 3.8—Standards cited in this code 3.0—Notation 3.1—Tests of materials 3.2—Cements 3.3—Aggregates 3.4—Water PART 3—CONSTRUCTION REQUIREMENTS CHAPTER 4—DURABILITY REQUIREMENTS 318-35 4.0—Notation 4.1—Water-cementitious materials ratio 4.2—Freezing and thawing exposures 4.3—Sulfate exposures 4.4—Corrosion protection of reinforcement CHAPTER 5—CONCRETE QUALITY, MIXING, AND PLACING 318-41 5.0—Notation 5.1—General 5.2—Selection of concrete proportions 5.3—Proportioning on the basis of field experience or trial mixtures, or both 5.4—Proportioning without field experience or trial mixtures 5.5—Average strength reduction 5.6—Evaluation and acceptance of concrete 5.7—Preparation of equipment and place of deposit 5.8—Mixing 5.9—Conveying 5.10—Depositing 5.11—Curing 5.12—Cold weather requirements 5.13—Hot weather requirements CHAPTER 6—FORMWORK, EMBEDDED PIPES, AND CONSTRUCTION JOINTS 318-57 6.1—Design of formwork 6.2—Removal of forms, shores, and reshoring 6.3—Conduits and pipes embedded in concrete 6.4—Construction joints CHAPTER 7—DETAILS OF REINFORCEMENT .318-63 7.0—Notation 7.1—Standard hooks 7.2—Minimum bend diameters 7.3—Bending 7.4—Surface conditions of reinforcement 7.5—Placing reinforcement 7.6—Spacing limits for reinforcement 7.7—Concrete protection for reinforcement 7.8—Special reinforcement details for columns 7.9—Connections 7.10—Lateral reinforcement for compression members 7.11—Lateral reinforcement for flexural members 7.12—Shrinkage and temperature reinforcement 7.13—Requirements for structural integrity ACI 318 Building Code and Commentary TABLE OF CONTENTS 318/318R-5 PART 4—GENERAL REQUIREMENTS CHAPTER 8—ANALYSIS AND DESIGN— GENERAL CONSIDERATIONS .318-79 8.0—Notation 8.1—Design methods 8.2—Loading 8.3—Methods of analysis 8.4—Redistribution of negative moments in continuous nonprestressed flexural members 8.5—Modulus of elasticity 8.6—Stiffness 8.7—Span length 8.8—Columns 8.9—Arrangement of live load 8.10—T-beam construction 8.11—Joist construction 8.12—Separate floor finish CHAPTER 9—STRENGTH AND SERVICEABILITY REQUIREMENTS 318-89 9.0—Notation 9.1—General 9.2—Required strength 9.3—Design strength 9.4—Design strength for reinforcement 9.5—Control of deflections CHAPTER 10—FLEXURE AND AXIAL LOADS 318-105 10.0—Notation 10.1—Scope 10.2—Design assumptions 10.3—General principles and requirements 10.4—Distance between lateral supports of flexural members 10.5—Minimum reinforcement of flexural members 10.6—Distribution of flexural reinforcement in beams and one-way slabs 10.7—Deep flexural members 10.8—Design dimensions for compression members 10.9—Limits for reinforcement of compression members 10.10—Slenderness effects in compression members 10.11—Magnified moments—General 10.12—Magnified moments—Nonsway frames 10.13—Magnified moments—Sway frames 10.14—Axially loaded members supporting slab system 10.15—Transmission of column loads through floor system 10.16—Composite compression members 10.17—Bearing strength CHAPTER 11—SHEAR AND TORSION 318-133 11.0—Notation 11.1—Shear strength 11.2—Lightweight concrete 11.3—Shear strength provided by concrete for nonprestressed members 11.4—Shear strength provided by concrete for prestressed members 11.5—Shear strength provided by shear reinforcement 11.6—Design for torsion 11.7—Shear-friction 11.8—Special provisions for deep flexural members 11.9—Special provisions for brackets and corbels 11.10—Special provisions for walls 11.11—Transfer of moments to columns 11.12—Special provisions for slabs and footings CHAPTER 12—DEVELOPMENT AND SPLICES OF REINFORCEMENT 318-181 12.0—Notation 12.1—Development of reinforcement—General 12.2—Development of deformed bars and deformed wire in tension 12.3—Development of deformed bars in compression 12.4—Development of bundled bars 12.5—Development of standard hooks in tension 12.6—Mechanical anchorage 12.7—Development of welded deformed wire fabric in tension 12.8—Development of welded plain wire fabric in tension 12.9—Development of prestressing strand 12.10—Development of flexural reinforcement—General 12.11—Development of positive moment reinforcement 12.12—Development of negative moment reinforcement 12.13—Development of web reinforcement 12.14—Splices of reinforcement—General 12.15—Splices of deformed bars and deformed wire in tension 12.16—Splices of deformed bars in compression 12.17—Special splice requirements for columns 12.18—Splices of welded deformed wire fabric in tension 12.19—Splices of welded plain wire fabric in tension ACI 318 Building Code and Commentary 318/318R-6 TABLE OF CONTENTS PART 5—STRUCTURAL SYSTEMS OR ELEMENTS CHAPTER 13—TWO-WAY SLAB SYSTEMS 318-209 13.0—Notation 13.1—Scope 13.2—Definitions 13.3—Slab reinforcement 13.4—Openings in slab systems 13.5—Design procedures 13.6—Direct design method 13.7—Equivalent frame method CHAPTER 14—WALLS 318-229 14.0—Notation 14.1—Scope 14.2—General 14.3—Minimum reinforcement 14.4—Walls designed as compression members 14.5—Empirical design method 14.6—Nonbearing walls 14.7—Walls as grade beams 14.8—Alternative design of slender walls CHAPTER 15—FOOTINGS .318-237 15.0—Notation 15.1—Scope 15.2—Loads and reactions 15.3—Footings supporting circular or regular polygon shaped columns or pedestals 15.4—Moment in footings 15.5—Shear in footings 15.6—Development of reinforcement in footings 15.7—Minimum footing depth 15.8—Transfer of force at base of column, wall, or reinforced pedestal 15.9—Sloped or stepped footings 15.10—Combined footings and mats CHAPTER 16—PRECAST CONCRETE 318-245 16.0—Notation 16.1—Scope 16.2—General 16.3—Distribution of forces among members 16.4—Member design 16.5—Structural integrity 16.6—Connection and bearing design 16.7—Items embedded after concrete placement 16.8—Marking and identification 16.9—Handling 16.10—Strength evaluation of precast construction CHAPTER 17—COMPOSITE CONCRETE FLEXURAL MEMBERS 318-253 17.4—Vertical shear strength 17.5—Horizontal shear strength 17.6—Ties for horizontal shear 17.0—Notation 17.1—Scope 17.2—General 17.3—Shoring CHAPTER 18—PRESTRESSED CONCRETE 318-257 18.0 18.1 18.2 18.3 18.4 —Notation —Scope —General —Design assumptions —Permissible stresses in concrete—Flexural members 18.5 —Permissible stresses in prestressing tendons 18.6 —Loss of prestress 18.7 —Flexural strength 18.8 —Limits for reinforcement of flexural members 18.9 —Minimum bonded reinforcement 18.10—Statically indeterminate structures 18.11—Compression members—Combined flexure and axial loads 18.12—Slab systems 18.13—Post-tensioned tendon anchorage zones 18.14—Design of anchorage zones for monostrand or single 5/8 in diameter bar tendons 18.15—Design of anchorage zones for multistrand tendons 18.16—Corrosion protection for unbonded prestressing tendons 18.17—Post-tensioning ducts 18.18—Grout for bonded prestressing tendons 18.19—Protection for prestressing tendons 18.20—Application and measurement of prestressing force 18.21—Post-tensioning anchorage zones and couplers 18.22—External post-tensioning ACI 318 Building Code and Commentary TABLE OF CONTENTS 318/318R-7 CHAPTER 19—SHELLS AND FOLDED PLATE MEMBERS .318-285 19.3—Design strength of materials 19.4—Shell reinforcement 19.5—Construction 19.0—Notation 19.1—Scope and definitions 19.2—Analysis and design PART 6—SPECIAL CONSIDERATIONS CHAPTER 20—STRENGTH EVALUATION OF EXISTING STRUCTURES .318-293 20.0—Notation 20.1—Strength evaluation—General 20.2—Determination of required dimensions and material properties 20.3—Load test procedure 20.4—Loading criteria 20.5—Acceptance criteria 20.6—Provision for lower load rating 20.7—Safety CHAPTER 21—SPECIAL PROVISIONS FOR SEISMIC DESIGN 318-299 21.0—Notation 21.1—Definitions 21.2—General requirements 21.3—Flexural members of special moment frames 21.4—Special moment frame members subjected to bending and axial load 21.5—Joints of special moment frames 21.6—Special reinforced concrete structural walls and coupling beams 21.7—Structural diaphragms and trusses 21.8—Foundations 21.9—Frame members not proportioned to resist forces induced by earthquake motions 21.10—Requirements for intermediate moment frames PART 7—STRUCTURAL PLAIN CONCRETE CHAPTER 22—STRUCTURAL PLAIN CONCRETE 318-335 22.5—Strength design 22.6—Walls 22.7—Footings 22.8—Pedestals 22.9—Precast members 22.10—Plain concrete in earthquake-resisting structures 22.0—Notation 22.1—Scope 22.2—Limitations 22.3—Joints 22.4—Design method COMMENTARY REFERENCES 318-345 APPENDIXES APPENDIX A—ALTERNATE DESIGN METHOD 318-357 A.0—Notation A.1—Scope A.2—General A.3—Permissible service load stresses A.4—Development and splices of reinforcement A.5—Flexure A.6—Compression members with or without flexure A.7—Shear and torsion APPENDIX B—UNIFIED DESIGN PROVISIONS FOR REINFORCED AND PRESTRESSED CONCRETE FLEXURAL AND COMPRESSION MEMBERS .318-367 B.1—Scope ACI 318 Building Code and Commentary 318/318R-8 TABLE OF CONTENTS APPENDIX C—ALTERNATIVE LOAD AND STRENGTH REDUCTION FACTORS 318-375 C.1—General APPENDIX D—NOTATION 318-377 APPENDIX E—STEEL REINFORCEMENT INFORMATION 318-385 INDEX 318-387 ACI 318 Building Code and Commentary .. .BUILDING CODE REQUIREMENTS FOR STRUCTURAL CONCRETE (ACI 318-99) AND COMMENTARY (ACI 318R-99) REPORTED BY ACI COMMITTEE 318 ACI Committee 318 Standard Building Code James R Cagley... standard ? ?Building Code Requirements for Structural Concrete (ACI 318-95).” This standard includes in one document the rules for all concrete used for structural purposes including both plain and. .. name implies, ? ?Building Code Requirements for Structural Concrete (ACI 318-99)? ?? is meant to be used as part of a legally adopted building code and as such must differ in form and substance from