Đang tải... (xem toàn văn)
Hướng dẫn cài đặt và sử dụng biến tần ABB ACS 800+ Cài đặt động cơ.+ Kích hoạt truyền thông với thiết bị lựa chọn+ Khởi động , dừng, dảo chiều quay.+ Thay đổi lượng đặt : tốc độ ,mô men, công nghệ.+ Reset lỗi.+ Thay đổi vị trí điều khiển tại chố và từ xa.
ACS800 Firmware Manual PDF created with pdfFactory Pro trial version www.pdffactory.com PDF created with pdfFactory Pro trial version www.pdffactory.com ACS800 Firmware Manual 3AFE64527592 REV I EN EFFECTIVE: 18.05.2007 ♥ 2007 ABB Oy All Rights Reserved PDF created with pdfFactory Pro trial version www.pdffactory.com PDF created with pdfFactory Pro trial version www.pdffactory.com Table of Contents Table of Contents Introduction to the manual Chapter overview Compatibility Safety instructions Reader Contents Product and service inquiries Product training Providing feedback on ABB Drives manuals 13 13 13 13 13 14 14 14 Start-up and control through the I/O Chapter overview How to start-up the drive How to perform the guided start-up (covers all essential settings) How to perform the limited start-up (covers only the basic settings) How to control the drive through the I/O interface How to perform the ID Run ID Run Procedure 15 15 15 17 21 22 22 Control panel Chapter overview Overview of the panel Panel operation mode keys and displays Status row Drive control with the panel How to start, stop and change direction How to set speed reference Actual signal display mode How to select actual signals to the display How to display the full name of the actual signals How to view and reset the fault history How to display and reset an active fault About the fault history Parameter mode How to select a parameter and change the value How to adjust a source selection (pointer) parameter Function mode How to enter an assistant, browse and exit How to upload data from a drive to the panel 25 25 26 26 27 27 28 29 29 30 30 31 31 32 32 33 34 35 36 Table of Contents PDF created with pdfFactory Pro trial version www.pdffactory.com How to download data from the panel to a drive How to set the contrast of the display Drive selection mode How to select a drive and change its panel link ID number Reading and entering packed boolean values on the display 37 38 39 39 40 Program features Chapter overview Start-up Assistant Introduction The default order of the tasks List of tasks and the relevant drive parameters Contents of the assistant displays Local control vs external control Local control External control Settings Diagnostics Block diagram: start, stop, direction source for EXT1 Block diagram: reference source for EXT1 Reference types and processing Settings Diagnostics Reference trimming Settings Example Programmable analogue inputs Update cycles in the Standard Control Program Settings Diagnostics Programmable analogue outputs Update cycles in the Standard Control Program Settings Diagnostics Programmable digital inputs Update cycles in the Standard Control Program Settings Diagnostics Programmable relay outputs Update cycles in the Standard Control Program Settings Diagnostics Actual signals Settings Diagnostics Motor identification Settings Power loss ride-through Automatic Start Table of Contents PDF created with pdfFactory Pro trial version www.pdffactory.com 41 41 41 41 42 43 43 44 44 44 44 45 45 46 46 46 47 47 48 49 49 49 49 50 50 50 50 51 51 51 51 52 52 52 52 53 53 53 53 53 54 54 Settings DC Magnetising Settings DC Hold Settings Flux Braking Settings Flux Optimisation Settings Acceleration and deceleration ramps Settings Critical speeds Settings Constant speeds Settings Speed controller tuning Settings Diagnostics Speed control performance figures Torque control performance figures Scalar control Settings IR compensation for a scalar controlled drive Settings Hexagonal motor flux Settings Programmable protection functions AI1242.0 rpm O ACS800 **WARNING** ID RUN SEL • để khởi động ID Run, nhấn phím (xem tham số 16.01 RUN ENABLE) Cảnh báo ID Run khởi động L -> 1242.0 rpm ACS800 **WARNING** MOTOR STARTS... rpm ACS800 **WARNING** ID RUN Cảnh báo sau hồn thành thành cơng ID Run I Start-up and control through the I/O PDF created with pdfFactory Pro trial version www.pdffactory.com L -> 1242.0 rpm ACS800