PPT3000 M Rule Customer Required Data Sheet 053008

615 Whitestown Road · P.O Box 149 · Butler, PA (USA) 16003-0149 Phone: 724/482-2163 · Fax: 724/482-2767 ·· Web Site: http://www.agrintl.com PPT3000 – M-RULE Profile Generation – data form The PPT3000 – M-Rule shelf-life testing routines are designed to provide material utilization and predicted shelf-life performance data on bottles at the point of production The PPT3000 M-Rule shelf-life prediction software utilizes pressure and expansion data captured by the PPT3000 in conjunction with the unique attributes of a given bottle This data is then analyzed by an embedded version of the M-Rule® Container Performance Model to provide predicted shelf life and material utilization of bottles tested Since shelf-life qualities are dependent on a number of critical bottle-specific parameters, it is extremely important that accurate data be provided to create each unique bottle shelf-life profile for the PPT3000 One profile is required for each unique bottle design to be tested In order to assist you in providing the proper data, we have prepared the following form This form must be completed and submitted for each unique bottle tested on the PPT3000 In addition to the data requested below, please also supply a design drawing of the bottle if available Data submitted on this form will be used to create a unique shelf-life profile for the specified bottle All information supplied will be treated with strict confidentiality Submission Information (Customer to complete) Agr Contact Date Job/Container Information for: _ (Container Name / Description) Customer Information Company Name Customer Contact Addr1 Addr2 City State/Province Country Phone: E-mail Customer Code Profile Name Postal Code AGR-use only Order Number PPT3000 Serial Number PO Number Thickness Shelf Life SET SET Executable Results Attached Name Material Utilization Report Attached Date Rev 7, 5/30/08 Page of NOTE: The Material (Resin), Finish Design, Base Design, and Closure selections are updated constantly If the Resin, Finish Design, Base Design, and/or Closure for the bottle does not appear, specify the Resin, Finish Design, Base Design, and/or Closure on the questionnaire under “Other” Material (Resin) Polyester: 1,5-PEN Polyester: 2,6-PEN Polyester: 2,6-PTN Blend: MonOxbar Single Sack™ V700X 6.7% LDR Polyester: 2,7-PEN Polyester: Eastman 9921/22 Polyester: Eastman 9921/22W Polyester: Heat Set PET – 30% Crystalline Polyester: Heat Set PET – 38% Crystalline Polyester: Invista 1101/1102 series Polyester: Eastman CB11/12 Polyester: M&G 8000 series Polyester: PCT Polyester: Poly(glycolic acid) Polyester: P(DEG)T Polyester: P(ethylene phthalate) Polyester: PBT Polyester: PET 21% crystalline Polyester: Poly(ethylene isophthalate) Polyester: Poly(ethylene terephthalate) Polyester: Poly(lactic acid) Polyolefin: EVOH 32 mol% ethylene – 27% cryst Polyolefin: EVOH 32 mol% ethylene – 61% cryst Polyolefin: LLDPE – 0.92 Polyolefin: O2 Scavenger Concentrate [193 cc O2/g] Polyolefin: EVOH 44 mole% ethylene – 27% cryst Polyolefin: HDPE – 0.96 Polyolefin: PMMA Polyolefin: Poly(vinyl alcohol) Polyolefin: Poly(vinyl chloride) Polyolefin: PP – 0.901 Polyamide: Grivory FE7103 21 Polyamide: Nylon Polyamide: Nylon MXD- Polyolefin: Polystyrene Polyamide: Grivory G Polyamide: Nylon 6,6 Others: Polyacetal Others: Polycarbonate Modified Resin: Constar MonOxbar™ V10 Modified Resin: Constar MonOxbar™ V6 Modified Resin: Constar Oxbar™ Multilayer Scavenger Other: Barrier Materials - Fill in only if barrier materials are employed on this bottle Important Note: The PPT-M-Rule shelf-life model assumes that coatings, and or barrier materials are applied properly and in place at the specified barrier levels Test results will reflect maximum shelf life based on barrier levels provided in this document No barrier materials employed Coating- internal or external Coating Type _ Barrier Improvement Factor for O2 (BIF) _ Internal External Multiple layer barrier For Multi-layer Bottles only Input thickness values below: Layer Resin Page of Weight % Provide thickness data for each layer with being the innermost layer and being the outermost layer General Data Item Value Unit  Nominal volume ml  Brimful capacity ml  Surface area Sq cm  Empty package weight grams  Nominal Thickness (Monolayer)** mm  Test Temperature C or F  Expected Shelf Life ** NOTE: it is important to have as accurate a value as possible for this parameter Refer to diagram for recommended measurement location Measure thickness on straight sidewall area with no decorations – take multiple measurements (8-10) using a high accuracy measurement device such as the Agr MBT and average the measurement results Finish Design Standard Crimp 28 mm 1716 28 mm PCO 38 mm PCO 38 mm Heat Set 43 mm VHS 28 mm 1716 RefPET 33 mm Sun Coast 48 mm VHJ 38 mm Cold Fill 28 mm SP400 PTI crimp 18 mm 43 mm VHS Lt Wt Petaloid Champagne Heatset Champagne Push-Up Crimp top 28 mm Alcoa 28 mm White Cap 28 mm Zapata 28/400 Zeller 28-4CO Top Seal 33 mm O-I 33 mm Sun Coast 38 mm Alcoa 38 mm White Cap 43 mm Alcoa Other: Base Design Heatset Petaloid Flat-bottom Other: Closure Page of 43 mm White Cap Other: Closure Material Polypropylene High Density Polyethylene Metal (impermeable) Other: Co2 Test Protocol Coke Standard Test Pepsi Standard Test 4.0-3.3 gas volume @ 22º C FTIR – empty bottle 4.0-3.3 gas volume @ 22º C Zahm-Nagle method - filled Custom test protocol Provide details below Required data for Custom test protocol if not using Coke or Pepsi standard tests Initial carbonation level: volumes Upper Carbonation Spec: _ volumes Lower Carbonation Spec: _ volumes Reference Test Method _ (FTIR, Zahm-Nagle, etc.) Test Temperature _ Package Fill Volume: Nominal Empty Brimful (defines how test is to be run) O2 Test Protocol Initial level: _ value _ units End level: _ value _ units Test Temperature _ Empty or Filled Container? Shelf-life values to be based on the following method: If both are chosen, profiles will be provided Tests are performed individually, not combined CO2 out gassing (egress) O2 ingress Please return completed form to the following: Page of ... Set 43 mm VHS 28 mm 1716 RefPET 33 mm Sun Coast 48 mm VHJ 38 mm Cold Fill 28 mm SP400 PTI crimp 18 mm 43 mm VHS Lt Wt Petaloid Champagne Heatset Champagne Push-Up Crimp top 28 mm Alcoa 28 mm White... multiple measurements (8-10) using a high accuracy measurement device such as the Agr MBT and average the measurement results Finish Design Standard Crimp 28 mm 1716 28 mm PCO 38 mm PCO 38 mm... the outermost layer General Data Item Value Unit  Nominal volume ml  Brimful capacity ml  Surface area Sq cm  Empty package weight grams  Nominal Thickness (Monolayer)** mm  Test Temperature