Subaru select monitor SSMII engine diagnostics

Subaru Select Monitor ENGINE (DIAGNOSTICS) Subaru Select Monitor 5) Turn the ignition switch to ON (engine OFF) and Subaru Select Monitor switch to ON A: OPERATION (A) HOW TO USE SUBARU SELECT MONITOR 1) Prepare the Subaru Select Monitor kit EN-00040 (A) Power switch 6) Using the Subaru Select Monitor, call up DTCs and data, then record them EN-00038 2) Connect the diagnosis cable to Subaru Select Monitor 3) Insert the cartridge to Subaru Select Monitor READ DIAGNOSTIC TROUBLE CODE (DTC) FOR ENGINE (NORMAL MODE) Refer to “Read Diagnostic Trouble Code” for information about how to indicate DTC READ DIAGNOSTIC TROUBLE CODE (DTC) FOR ENGINE (OBD MODE) Refer to “Read Diagnostic Trouble Code” for information about how to indicate DTC EN-00039 4) Connect the Subaru Select Monitor to the data link connector at the lower portion of instrument panel (on the driver’s side) EN-03693 CAUTION: Do not connect any scan tools except Subaru Select Monitor or general scan tool EN(H6DO)(diag)-26 Subaru Select Monitor ENGINE (DIAGNOSTICS) READ CURRENT DATA FOR ENGINE (NORMAL MODE) 1) On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key 2) On the «System Selection Menu» display screen, select the {Engine} and press the [YES] key 3) Press the [YES] key after the information of engine type has been displayed 4) On the «Engine Diagnosis» display screen, select the {Current Data Display/Save}, and then press the [YES] key 5) On the «Data Display Menu» screen, select the {Data Display} and press the [YES] key 6) Using the scroll key, scroll the display screen up or down until the desired data is shown • A list of the support data is shown in the following table Description Display Unit of measure % rpm km/h or MPH deg °C or °F g/s or lb/m % Note (at idling) 3.5% ≥ 75°C or 167°F (After engine is warmed-up.) 3.1% 0.0% 4.7% 0.0% 200 — 300 mmHg, 26.7 — 40 kPa, 7.8 — 11.8 inHg or 3.8 — 5.8 psig 600 — 800 rpm km/h or MPH 13 — 15 deg (Ambient air temperature) 3.8 g/s or 0.5 lb/m 1.2 — 1.6% V 0.035 V V 0.020 V V V ms ms deg mmHg, kPa, inHg or psig 12 — 14 V 1.1 — 1.2 V 2.82 ms 2.82 ms deg Engine load Engine load Engine coolant temperature signal Coolant Temp A/F compensation A/F learning A/F compensation A/F learning A/F Compensation A/F learning A/F Compensation A/F learning Intake manifold absolute pressure Mani Absolute Pressure Engine speed signal Meter vehicle speed signal Ignition timing signal Intake air temperature signal Amount of intake air Throttle opening angle signal Battery voltage Mass air flow voltage Injection pulse width Injection pulse width Knock sensor compensation Engine speed Meter vehicle speed Ignition timing Intake air temperature Mass Air Flow Throttle valve angle Front oxygen sensor voltage value Front oxygen sensor voltage value Battery Voltage Mass air flow voltage Injection pulse width Injection pulse width Knock correction Atmospheric pressure signal Atmospheric pressure Intake manifold relative pressure Intake manifold relative pressure mmHg, kPa, inHg or psig Acceleration opening angle signal Radiator fan output Purge control solenoid valve duty ratio Generator duty Fuel pump duty Variable valve timing advance angle amount R Variable valve timing advance angle amount L Oil flow control solenoid valve duty R Oil flow control solenoid valve duty L Oil flow control solenoid valve current R Oil flow control solenoid valve current L Front oxygen (A/F) sensor current value Front oxygen (A/F) sensor current value Front oxygen (A/F) sensor resistance value Acceleration opening angle Radiator fan output CPC Duty ALT duty Fuel pump duty VVT advance angle amount R VVT advance angle amount L OCV duty R OCV duty L OCV current R OCV current L A/F sensor current value A/F sensor current value A/F sensor resistance value % % % % % deg deg % % mA mA mA mA Ω Front oxygen sensor voltage value Front oxygen sensor voltage value EN(H6DO)(diag)-27 °C or °F % % % % mmHg, kPa, inHg or psig (Atmospheric pressure) (Intake manifold absolute pressure — atmospheric pressure) 0% 0% — 3% 0% 33% deg deg 9.4% 9.4% 64 mA 64 mA 0.0 mA 0.0 mA 31 Ω Subaru Select Monitor ENGINE (DIAGNOSTICS) Description Front oxygen (A/F) sensor resistance value Front oxygen (A/F) sensor output lambda Front oxygen (A/F) sensor output lambda Fuel temperature signal A/F compensation A/F learning Throttle motor duty Throttle power supply voltage Sub throttle sensor voltage Main throttle sensor voltage Sub acceleration sensor voltage Main acceleration sensor voltage Memory vehicle speed A/F compensation A/F learning Fuel level sensor resistance Unit of measure Ω — — mmHg, kPa, Fuel Tank Pressure inHg or psig Fuel Temp °C or °F A/F Compensation % A/F learning % Throttle motor duty % Throttle power supply voltage V Sub throttle sensor voltage V Main throttle sensor voltage V Sub acceleration sensor voltage V Main acceleration sensor voltage V Memory vehicle speed km/h or MPH A/F Compensation % A/F learning % Fuel level resistance Ω Oil temperature Oil Temperature °C Oil switching solenoid valve duty R Oil switching solenoid valve duty L Oil switching solenoid valve current R Oil switching solenoid valve current L Variable valve lift mode #1 cylinder roughness monitor #2 cylinder roughness monitor #3 cylinder roughness monitor #4 cylinder roughness monitor #5 cylinder roughness monitor #6 cylinder roughness monitor Test mode terminal Neutral position switch signal Idle switch signal Ignition switch signal Power steering switch signal Air conditioning switch signal Starter switch signal Front oxygen monitor Front oxygen monitor Knocking signal Crankshaft position sensor signal Camshaft position sensor signal Drain valve signal Rear defogger switch signal Blower fan switch signal Light switch signal Wiper switch signal A/C middle pressure switch signal A/C compressor relay signal OSV duty R OSV duty L OSV current R OSV current L VVL Lift Mode #1 cylinder roughness monitor #2 cylinder roughness monitor #3 cylinder roughness monitor #4 cylinder roughness monitor #5 cylinder roughness monitor #6 cylinder roughness monitor Test mode terminal Neutral SW Soft idle SW Ignition SW Power steering SW input signal A/C SW Starter SW Front oxygen monitor Front oxygen monitor Knock signal Crankshaft angle signal Camshaft angle signal Vent Solenoid Valve Rear defogger SW Blower fan SW Light SW Wiper SW A/C middle pressure SW A/C compressor relay output AT coordinate retard angle demand % % mA mA — — — — — — — — — — — — — — — — — — — — — — — — — — Note (at idling) 31 Ω 1.00 1.00 +8.8 mmHg, +1.2 kPa, +0.4 inHg or +0.17 psig +28°C or +82°F –0.16% 0.0% –27% (Battery voltage) 1.50 V 0.64 V 0.7 V 0.7 V km/h or MPH 0.31% 0.0% — 96 Ω ≥ 85°C (After engine is warmed-up.) 17.3% 17.3% 192 mA 192 mA 0 0 0 U check Neutral In idle ON input OFF input (when OFF) OFF input (when OFF) OFF input Rich Rich OFF Yes Yes OFF output (when OFF) OFF input (when OFF) OFF input (when OFF) OFF input (when OFF) OFF input (when OFF) OFF input OFF output — Yes Fuel tank pressure signal AT coordinate retard angle demand signal Display A/F sensor resistance value A/F sensor output lambda A/F sensor output lambda EN(H6DO)(diag)-28 Subaru Select Monitor ENGINE (DIAGNOSTICS) Description AT coordinate fuel cut demand signal Vehicle dynamics control (VDC) torque down prohibition output Vehicle dynamics control (VDC) torque down demand AT coordinate permission signal Electronic throttle control motor relay signal Stop light switch signal SET/COAST switch signal RESUME/ACCEL switch signal Brake switch signal Main switch signal Body integrated unit data reception Body integlated unit counter update Cruise control cancel switch signal Variable valve lift diagnosis oil pressure switch signal Variable valve lift diagnosis oil pressure switch signal Display AT coordinate fuel cut demand Unit of measure — Note (at idling) OFF Ban of Torque Down — Permission VDC torque down demand — OFF AT coordinate permission signal ETC motor relay Stop Light Switch SET/COAST SW RESUME/ACCEL SW Brake SW Main SW Body Int Unit Data Body Int Unit Count CC Cancel SW — — — — — — — — — — Permission ON OFF OFF OFF OFF OFF Yes Yes OFF Oil Temperature SW1 — ON Oil Temperature SW2 — ON READ CURRENT DATA FOR ENGINE (OBD MODE) 1) On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key 2) On the «System Selection Menu» display screen, select the {Engine} and press the [YES] key 3) Press the [YES] key after the information of engine type has been displayed 4) On the «Engine Diagnosis» display screen, select the {OBD System} and press the [YES] key 5) On the «OBD Menu» display screen, select the {Current Data Display/Save}, and then press the [YES] key 6) On the «Data Display Menu» screen, select the {Data Display} and press the [YES] key 7) Using the scroll key, scroll the display screen up or down until the desired data is shown • A list of the support data is shown in the following table Description Number of diagnosis code Condition of malfunction indicator light Monitoring test of misfire Monitoring test of fuel system Monitoring test of comprehensive component Test of catalyst Test of heating-type catalyst Test of evaporative emission purge control system Test of secondary air system Test of air conditioning system refrigerant Test of oxygen sensor Test of oxygen sensor heater Test of EGR system A/F control #1 A/F control #2 Calculated load valve Engine coolant temperature A/F compensation #1 A/F learning #1 A/F compensation #2 A/F learning #2 Display Number of Diag Codes: MI (MIL) Misfire monitoring Fuel system monitoring Component monitoring Catalyst Diagnosis Heated catalyst Evaporative purge system Secondary air system A/C system refrigerant Oxygen senor Oxygen sensor heater EGR system Fuel system for Bank Fuel system for Bank Calculated load valve Coolant Temp Short term fuel trim B1 Long term fuel trim B1 Short term fuel trim #2 Long term fuel trim B2 EN(H6DO)(diag)-29 Unit of measure ON or OFF Finish Finish Finish Finish or incomplete No Finish or incomplete No No Finish or incomplete Finish No support OPEN early period OPEN early period % °C % % % % Subaru Select Monitor ENGINE (DIAGNOSTICS) Description Intake manifold absolute pressure Engine speed Vehicle speed Ignition timing #1 Intake air temperature Amount of intake air Throttle valve angle Oxygen sensor #12 A/F compensation #12 Oxygen sensor #22 A/F compensation #22 OBD system Oxygen sensor #11 Oxygen sensor #12 Oxygen sensor #21 Oxygen sensor #22 A/F sensor #11 A/F sensor #11 A/F sensor #21 A/F sensor #21 A/F sensor #11 A/F sensor #11 A/F sensor #21 A/F sensor #21 Display Mani Absolute Pressure Engine speed Vehicle speed Ignition timing adv.#1 Intake Air Temp Mass Air Flow Throttle Opening Angle Oxygen sensor #12 Short term fuel trim #12 Oxygen sensor #22 Short term fuel trim #22 OBD System Oxygen sensor #11 Oxygen sensor #12 Oxygen sensor #21 Oxygen sensor #22 A/F sensor #11 A/F sensor #11 A/F sensor #21 A/F sensor #21 A/F sensor #11 A/F sensor #11 A/F sensor #21 A/F sensor #21 Unit of measure mmHg, kPa, inHg or psig rpm km/h or MPH ° °C or °F g/s or lb/m % V % % % — support support support support — V — V — mA — mA NOTE: For detailed operation procedure, refer to the “SUBARU SELECT MONITOR OPERATION MANUAL” EN(H6DO)(diag)-30 Subaru Select Monitor ENGINE (DIAGNOSTICS) READ FREEZE FRAME DATA FOR ENGINE (OBD MODE) 1) On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key 2) On the «System Selection Menu» display screen, select the {Engine} and press the [YES] key 3) Press the [YES] key after the information of engine type has been displayed 4) On the «Engine Diagnosis» display screen, select the {OBD System} and press the [YES] key 5) On the «OBD Menu» display screen, select the {Freeze Frame Data} and press the [YES] key • A list of the support data is shown in the following table Description DTC of freeze frame data Air fuel ratio control system for bank Air fuel ratio control system for bank Engine load data Engine coolant temperature signal Short term fuel trim by front oxygen (A/F) sensor (Bank 1) Long term fuel trim by front oxygen (A/F) sensor (Bank 1) Short term fuel trim by front oxygen (A/F) sensor (Bank 2) Long term fuel trim by front oxygen (A/F) sensor (Bank 2) Intake manifold absolute pressure signal Engine speed signal Vehicle speed signal Ignition timing #1 Intake air temperature Amount of intake air Throttle valve angle Oxygen sensor #12 A/F compensation #12 Oxygen sensor #22 A/F compensation #12 Oxygen sensor #11 Oxygen sensor #12 Oxygen sensor #21 Oxygen sensor #22 Display Freeze frame data Fuel system for Bank1 Fuel system for Bank2 Engine Load Coolant Temp Short term fuel trim B1 Long term fuel trim B1 Short term fuel trim B2 Long term fuel trim B2 Mani Absolute Pressure Engine Speed Vehicle Speed Ignition timing adv #1 Intake Air Temp Mass Air Flow Throttle Opening Angle Oxygen sensor #12 Short term fuel trim #12 Oxygen sensor #22 Short term fuel trim #22 Oxygen sensor #11 Oxygen sensor #12 Oxygen sensor #21 Oxygen sensor #22 Unit of measure DTC — — % °C or °F % % % % mmHg, kPa, inHg or psig rpm km/h or MPH ° °C g/s % V % V % support support support support NOTE: For detailed operation procedure, refer to the “SUBARU SELECT MONITOR OPERATION MANUAL” EN(H6DO)(diag)-31 Subaru Select Monitor ENGINE (DIAGNOSTICS) LED OPERATION MODE FOR ENGINE 1) On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key 2) On the «System Selection Menu» display screen, select the {Engine} and press the [YES] key 3) Press the [YES] key after the information of engine type has been displayed 4) On the «Engine Diagnosis» display screen, select the {Current Data Display/Save}, and then press the [YES] key 5) On the «Data Display» screen, select the {Data LED Display} and press the [YES] key 6) Using the scroll key, scroll the display screen up or down until the desired data is shown • A list of the support data is shown in the following table Description Test mode signal Neutral position switch signal Idle switch signal Ignition switch signal Power steering switch signal Air conditioning switch signal Starter switch signal Front oxygen monitor Front oxygen monitor Knocking signal Crankshaft position sensor signal Camshaft position sensor signal Rear defogger switch signal Blower fan switch signal Light switch signal Wiper switch signal A/C middle pressure switch signal Air conditioner compressor relay signal Drain valve signal AT retard angle demand signal AT fuel cut signal VDC torque down prohibition output VDC torque down demand AT coordinate permission signal Electronic throttle control motor relay signal Stop light switch signal SET/COAST switch signal RESUME/ACCEL switch signal Brake switch signal Main switch signal Body integrated unit data reception Body integrated unit counter update Cruise control cancel switch signal Variable valve lift diagnosis oil pressure switch signal Variable valve lift diagnosis oil pressure switch signal Display Test mode terminal Neutral SW Soft idle SW Ignition SW Power steering SW A/C SW Starter SW FtO2 monitor FtO2 monitor Knock signal Crankshaft angle signal Camshaft angle signal Rear defogger SW Blower fan SW Light SW Wiper SW A/C middle pressure SW Message D check/U check Neutral/Other than neutral Idle/Other than idle ON Input/OFF Input ON Input/OFF Input ON Input/OFF Input ON Input/OFF Input Lean/Rich Lean/Rich Yes/No Yes/No Yes/No ON Input/OFF Input ON Input/OFF Input ON Input/OFF Input ON Input/OFF Input ON Input/OFF Input When LED “ON” required D check Neutral In idle ON input ON input ON input ON input Rich Rich Yes Yes Yes ON input ON input ON input ON input ON input Compressor relay ON output/OFF output Vent Solenoid Valve AT retard angle demand AT fuel cut Torque down output Torque down demand AT coordinate permission signal ON or OFF Yes/No Yes/No ON/OFF Yes/No ON/OFF Permission ETC motor relay ON/OFF ON Stop SW SET/CST SW RES/ACC SW Brake SW Main SW Body Int Unit Data Body Int Unit Count CC Cancel SW ON Input/OFF Input ON Input/OFF Input ON Input/OFF Input ON Input/OFF Input ON Input/OFF Input Yes/No Yes/No ON Input/OFF Input Oil Temperature SW1 ON/OFF ON Oil Temperature SW2 ON/OFF ON ON output When drain valve is ON Yes Yes Prohibition Yes ON input ON input ON input ON input ON input Yes Yes ON input NOTE: For detailed operation procedure, refer to the “SUBARU SELECT MONITOR OPERATION MANUAL” EN(H6DO)(diag)-32 Subaru Select Monitor ENGINE (DIAGNOSTICS) VIN REGISTRATION 1) On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key 2) On the «System Selection Menu» display screen, select the {Engine} and press the [YES] key 3) Press the [YES] key after the information of engine type has been displayed 4) On the «Engine Diagnosis» display screen, select the {VIN Registration} and press the [YES] key 5) Perform the procedure shown on display screen NOTE: For detailed operation procedure, refer to the “SUBARU SELECT MONITOR OPERATION MANUAL” EN(H6DO)(diag)-33 ... the SUBARU SELECT MONITOR OPERATION MANUAL” EN(H6DO)(diag)-30 Subaru Select Monitor ENGINE (DIAGNOSTICS) READ FREEZE FRAME DATA FOR ENGINE (OBD MODE) 1) On the «Main Menu» display screen, select. .. refer to the SUBARU SELECT MONITOR OPERATION MANUAL” EN(H6DO)(diag)-31 Subaru Select Monitor ENGINE (DIAGNOSTICS) LED OPERATION MODE FOR ENGINE 1) On the «Main Menu» display screen, select the... procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL” EN(H6DO)(diag)-32 Subaru Select Monitor ENGINE (DIAGNOSTICS) VIN REGISTRATION 1) On the «Main Menu» display screen, select the {Each System