Đang tải... (xem toàn văn)
Kirigami là nghệ thuật cắt giấy truyền thống của Nhật Bản, với tên gọi được ghép từ hai chữ : “kiru” (có nghĩa là cắt) và “kami” (là giấy). Tính đối xứng là đặc điểm nổi bật nhất trong kirigami truyền thống. Hình bông tuyết, ngũ giác, và bông hoa là những hình ảnh cổ điển quen thuộc đặc trưng cho kirigami mà trong đó, cắt giấy đơn thuần chỉ nhằm tôn lên cấu trúc tối giản, cân xứng nhưng cũng rất linh hoạt của thiết kế. Nghệ thuật cắt giấy được cho là lần đầu tiên xuất hiện trong các đền chùa Nhật Bản như một cách thể hiện lòng thành kính trước các vị thần. Đến khoảng thế kỷ XVII, Kirigami được biết đến rộng rãi khắp châu Á như một hình thức nghệ thuật đích thực. Không chỉ riêng ở Nhật mà cả ở Trung Quốc, người ta tạo nên các thiết kế kirigami để biểu trưng cho những điều tốt đẹp và quan trọng như: Thịnh vượng, Hoàn hảo, Quý phái, Trang nhã hay thậm chí là mối liên kết giữa con người và vũ trụ. Bunraku, một loại hình múa rối Nhật Bản đôi lúc cũng sáng tạo những con rối bằng giấy từ kỹ thuật Kirigami, nhưng vẫn đảm bảo các bộ phận có thể cử động được.
Sydney Opera House (Australia): Assembly Instructions Canon ® is a registered trademark of Canon Inc © Canon Inc © A & A Co., Ltd Before starting assembly:Writing the number of each section on its back side before cutting out the sections is highly recommended (* This way, you can be sure which section is which even after cutting out the sections.) Indicates where sections should be glued together http://www.canon.com/c-park/en/ (1) Build the base View of completed model *This model was designed for Papercraft and may differ from the original in some respects Assembly Instructions: Six A4 sheets (No.1 to No.6) *Build the model by carefully reading the Assembly Instructions, in the parts sheet page order *Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold Assembly Instructions Mountain fold(dotted line) Make a mountain fold Valley fold(dashed and dotted line) Make a valley fold Scissors line(solid line) Cut along the line Cut in line(solid line) Cut along the line Tools and materials Assembly tip Caution Glue The glue spot(colored dot) shows where to apply the glue Glue spot(Red dot) Glue parts with the same number together ouse era H ey Op ustralia Sydn Sydney, A Glue spot(Green dot) Glue within the same part Insert Glue spot(Blue dot) Glue to the rear of the other part Scissors, set square, glue(We recommend stick glue), pencil, used ballpoint pen, toothpicks, tweezers, (useful for handling small parts) Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff Glue, scissors and other tools may be dangerous to young children so be sure to keep them out of the reach of young children Sydney Opera House (Australia): Assembly Instructions Canon ® is a registered trademark of Canon Inc © Canon Inc © A & A Co., Ltd (2) Build the fan-shaped foundation 13 10 15 12 14 11 Sydney Opera House (Australia): Assembly Instructions (3) Build the lower level of the structure Insert between the folded sides 25 Canon ® is a registered trademark of Canon Inc © Canon Inc © A & A Co., Ltd 21 Insert between the folded sides Fold each of parts 21, 22, 24, and 25 before gluing them to part 17 24 * Since folding these parts after gluing them to part 17 may cause the paper on the exterior to stick out or tear, be sure to glue these parts in place after folding them Match the borders of the coloring when gluing these pieces together 19 18 17 Insert between the folded sides Match the borders of the coloring when gluing these pieces together 20 22 When assembling this section, first attach parts 21, 22, 24, and 25 to part 17, then connect the parts together by adjusting the location of the connection between each part Insert between the folded sides 16 Sydney Opera House (Australia): Assembly Instructions Canon ® is a registered trademark of Canon Inc © Canon Inc © A & A Co., Ltd 41 Glue in the same way as on the opposite side 34 31 30 Glue along the dotted line 23 33 26 27 Bend this piece slightly before gluing it 28 41 Large hall Glue in the same way as part 29 (4) Build the large and small halls and the restaurant 32 Assemble parts 33, 35, 38, 45, 52, 55, and 56 in the same general way 35 40 Glue in the same way as on the opposite side 39 Bend this piece slightly before gluing it 38 Glue together 29 36 37 Bend this piece slightly before gluing it 37 40 36 Assemble parts 30, 32, 34, 39, 44, 50, 53, 54, 57, and 59 in the same general way Glue one side to part 38 and one side to part 32 Glue parts 28, 29, 40, and 41 in place last, adjusting the assembled parts while doing so Sydney Opera House (Australia): Assembly Instructions 49 47 Small hall 50 Canon ® is a registered trademark of Canon Inc © Canon Inc © A & A Co., Ltd Glue in the same way as on the opposite side Glue in the same way as part 46 53 59 60 54 Glue in the same way as on the opposite side 55 48 57 Glue in the same way as on the opposite side 56 52 45 44 61 Restaurant 51 Bend this piece slightly before gluing it Bend this piece slightly before gluing it 49 46 Glue in the same way as on the opposite side 58 Bend this piece slightly before gluing it Bend this piece slightly before gluing it 43 61 48 42 Glue parts 46, 47, 48, 49, and 61 in place last, after assembling all these parts together, adjusting the assembled parts while doing so Glue one side to the rear side of part 44 and one side to part 50 (5) Glue the large and small halls and the restaurant to (3) the lower section of the structure (3) Small hall Large hall Restaurant (3) Lower section of structure Sydney Opera House (Australia): Assembly Instructions Canon ® is a registered trademark of Canon Inc © Canon Inc © A & A Co., Ltd (6) Complete the model by gluing the base assembled in step (1) to the foundation assembled in step (2) and the structure assembled in step (5) (5) Structure (2) Foundation (1) Base Finished!