Synthesis and characterizations of polymer electrolyte membranes based on aliphatic ionomers

SYNTHESIS AND CHARACTERIZATIONS OF POLYMER ELECTROLYTE MEMBRANES BASED ON ALIPHATIC IONOMERS DAVID JULIUS NATIONAL UNIVERSITY OF SINGAPORE 2011 Thesis Spine SYNTHESIS AND CHARACTERIZATIONS OF POLYMER ELECTROLYTE MEMBRANES BASED ON ALIPHATIC IONOMERS DAVID JULIUS 2011 SYNTHESIS AND CHARACTERIZATIONS OF POLYMER ELECTROLYTE MEMBRANES BASED ON ALIPHATIC IONOMERS DAVID JULIUS (B. Eng., UNPAR; M. Sc., NUS) A THESIS SUBMITTED FOR THE DEGREE OF DOCTOR OF PHILOSOPHY DEPARTMENT OF CHEMICAL AND BIOMOLECULAR ENGINEERING NATIONAL UNIVERSITY OF SINGAPORE 2011 ACKNOWLEDGEMENT First of all, I would like to express my deepest and greatest gratitude to my main supervisor, Professor Lee Jim Yang, and my co-supervisor, Associate Professor Hong Liang, for their guidance, patience, support and advices throughout my entire PhD study. Prof. Lee has been the maestro conductor in this PhD thesis study. Like a symphony, he helped me to set the tempo, prepared me for the execution, and listened and critiqued my performance. He shaped the direction of the research project and the physical form of the thesis as it is presented today. His inspirational stories and unconventional ideas have always been a source of motivation. Prof. Hong, on the other hand, has been my resourceful chef de cuisine, who is in charge of the details of the scientific investigation. His immense knowledge in polymer chemistry has helped me overcome many synthesis difficulties and rationalized many of the “perplexing” observations encountered in this study. I am grateful to National University of Singapore, in particular the Chemical and Biomolecular Engineering department for their generous scholarship supports that make this study possible. I would also like to thank my close friends and colleagues in our research group with whom I have formed a strong bond: Dr. Nikken Wiradharma, Dr. Deny Hartono, Mr. Usman Oemar, Dr. Natalia Widjojo, Ms. Fang Chunliu, Dr. Fu Rongqiang, Dr. Tay Siok Wei, Dr. Zhang Xinhui, Dr. Pei Haiqing, Dr. Zhou Weijiang, Dr. Zhang Qingbo, Mr. Cheng Chin Hsien, Dr. Deng Da, Dr. Yang Jinhua, Ms. Yu Yue, Ms. Lu Meihua, Ms. Ji Ge, Mr. Ma Yue, Mr. Bao Ji, Mr. Chia Zhi Wen, Mr. Yao Qiaofeng, Mr. Chen Dongyun, Dr. Liu Bo, Dr. Zhang Cao. My indebtedness also goes to all friends that had supported me in many ways during my PhD studies. I also want to i express my gratitude to Mr. Boey Kok Hong, Ms. Lee Cai Keng, Mr. Chia Pai An, Mr. Mogan, Ms. Samantha Fam, Dr. Yuan Ze Liang, and to all laboratory and professional staffs in Chemical and Biomolecular Engineering department for their technical assistance. The support, friendship, and encouragement of these people have helped to make this PhD study a journey of happiness. Thanks are also extended to my PhD examination panel, A/Prof. Loh Kai Chee, A/Prof. Chen Shing Bor, and Asst/Prof. Karl Erik Birgersson, for their valuable assessment and suggestion on this thesis and my future career. I would to express my sincere thank to Professor Peter N. Pintauro, who has been my inspiring teacher in this research study. Last but not least, I would like to thank my family members: my parents, my brothers, and also to my fiancée. Without their support and encouragement, I may not finish writing up this piece of work. ii TABLE OF CONTENTS ACKNOWLEDGEMENT . i SUMMARY . vii NOMENCLATURES x LIST OF FIGURES . xiii LIST OF TABLES . xix INTRODUCTION 1.1 Problem Statement .1 1.2 Objective and Scope of Thesis .4 (a) Design and Synthesis of New Alcohol-Resistant Alternative PEMs based on Aliphatic Random Ionomers .5 (b) Structural Characterizations of Random Aliphatic Ionomers and Investigations of the Effects of Hydrophobic Functional Groups on Phase Separation in Solution .5 (c) Development of New PEMs based on Aliphatic Block Ionomers and Hydrophilic Covalent Cross-links (d) Investigations of a One-pot ATRP Method and the Phase Separation of Aliphatic Block Ionomers in Solution .7 1.3 Organization of Thesis .7 LITERATURE REVIEW .8 2.1 Scope of the Review 2.2 Ionomers for DAFC Applications 2.2.1 DAFCs .8 2.2.2 Membrane Electrode Assembly (MEA) 10 2.2.3 Ionomers for Polymer Electrolyte Membranes (PEMs) 12 2.3 2.2.3.1 Modified Nafion® Membranes .13 2.2.3.2 Hydrocarbon Membranes .18 Ionomers: Synthesis, Structure, and Properties .24 2.3.1 Synthesis of Ionomers: Radical Polymerization 25 2.3.1.1 Synthesis of Random and Block Ionomers 25 2.3.1.2 Atom Transfer Radical Polymerization (ATRP) .29 2.3.2 Phase Separation of Ionomers in Solution and in the Solid State 32 iii 2.3.2.1 Phase Separation of Random and Block Ionomers in Solution .33 2.3.2.2 Phase Separation of Random and Block Ionomers in the Solid State 36 SYNTHESIS AND CHARACTERIZATION OF ACRYLIC RANDOMIONOMER MEMBRANES FOR ROOM TEMPERATURE DIRECT ETHANOL FUEL CELLS 41 3.1 Introduction 41 3.2 Experimental Method .43 3.2.1 Materials 43 3.2.2 Synthesis of Random Ionomers .44 3.2.3 Fabrication of Random-Ionomer Membranes 45 3.2.4 Characterization Methods 46 3.3 3.2.4.1 Proton Conductivity .46 3.2.4.2 Alcohol Permeability .47 3.2.4.3 Ion-Exchange Capacity (IEC) and Water Uptake 48 3.2.4.4 Mechanical Properties 48 Results and Discussion 49 3.3.1 Ternary Random-Ionomer Membranes for DEFCs .49 3.3.1.1 Rational Design and Synthesis of Ethanol-Resistant Random- Ionomer Membranes 49 3.3.1.2 PEM Properties of the Ternary Random-Ionomer Membranes .53 3.3.2 The Benevolent Effects of the Addition of Strongly Hydrophobic TFPM to Form Quaternary Random-Ionomer Membranes 54 3.3.2.1 Proton Conductivity .55 3.3.2.2 Ethanol Permeability 58 3.3.2.3 Mechanical Properties 61 3.3.3 Reflection on the Design Strategy for Aliphatic Ionomer Membranes .64 3.4 Conclusion .65 MITIGATING EARLY PHASE SEPARATION DURING SOLUTION POLYMERIZATION OF ALIPHATIC RANDOM IONOMERS BY HYDROPHOBIC MODIFIER ADDITION 66 4.1 Introduction 66 4.2 Experimental Method .69 4.2.1 Synthesis of Random Ionomers and Membrane Fabrications .69 iv 4.2.2 Additional Characterization Methods 69 4.3 4.2.2.1 Viscosity 69 4.2.2.2 Zeta Potential .70 4.2.2.3 Laser Light Scattering (LLS) .70 4.2.2.4 Transmission Electron Microscopy (TEM) .71 4.2.2.5 Spectroscopic Analyses .71 Results and Discussions .71 4.3.1 Effects of Hydrophobic Modifier Addition on Phase Separation during Copolymerization .71 4.3.2 Influence of Co-monomer Distribution on Solution Behavior 74 4.3.3 Structures of Ternary and Quaternary Random Ionomers .79 4.4 Conclusion .85 DEVELOPMENT OF POLYMER ELECTROLYTE MEMBRANES BASED ON HYDROPHILIC COVALENTLY CROSS-LINKED ALIPHATIC DIBLOCK IONOMERS .86 5.1 Introduction 86 5.2 Experimental 90 5.2.1 Materials 90 5.2.2 Synthesis of Aliphatic Diblock Ionomers by a One-pot Atom Transfer Radical Polymerization (ATRP) Technique 90 5.2.3 Membrane Formation and Pre-treatment .92 5.2.4 Characterization Methods 93 5.2.4.1 Electrochemical Analysis .93 5.2.4.2 Alcohol Permeability .93 5.2.4.3 Ion-Exchange Capacity (IEC), Alcohol and Water Uptake, and Dimensional Stability .93 5.3 5.2.4.4 Examination of Membrane Morphology .94 5.2.4.5 MEA Preparation and DMFC Tests .94 Results and Discussion 95 5.3.1 Design and Synthesis of Diblock Ionomer Membranes with Hydrophilic Covalent Cross-links 95 5.3.2 Proton Conductivity .100 5.3.3 Liquid Uptake and Dimensional Stability 103 5.3.4 Alcohol Permeability .107 v 5.3.5 Membrane Morphologies .111 5.3.6 MEA Fabrication and DMFC Performance .115 5.4 Conclusion .118 ONE-POT SYNTHESIS OF 3-SULFOPROPYL METHACRYLATE-BASED DIBLOCK IONOMERS AND THEIR PHASE SEPARATION BEHAVIOR IN SOLUTION 119 6.1 Introduction 119 6.2 Experimental Section .121 6.2.1 Materials and Synthesis of Block Ionomers 121 6.2.2 Additional Characterization Methods 121 6.3 6.2.2.1 Chromatographic Analysis .121 6.2.2.2 Spectroscopic Analysis 122 6.2.2.3 Zeta Potential Measurements .123 6.2.2.4 Laser Light Scattering (LLS) Measurements .123 6.2.2.5 Transmission Electron Microscopy (TEM) .124 Results and Discussion 124 6.3.1 Synthesis and Structure of P(AN-co-GMA)-b-SPM Diblock Ionomers 124 6.3.1.1 Feed Composition 126 6.3.1.2 Processing Conditions 126 6.3.2 Phase Separation Behavior of P(AN-co-GMA)-b-SPM Diblock Ionomers in DMSO/Water Mixtures 132 6.4 Conclusion .141 CONCLUSIONS AND RECOMMENDATIONS FOR FUTURE WORK 142 7.1 Conclusions 142 7.2 Recommendations for Future Work .145 7.2.1 Other Applications of Hydrophilic Covalently Cross-linked Diblock Ionomer Membranes 145 7.2.2 Development of Hydrophilic Covalently Cross-linked Diblock Ionomer Membranes for Medium-Temperature DAFCs .146 PUBLICATIONS AND CONFERENCES 148 Patents 148 Publications 148 Conferences 148 REFERENCES .150 vi SUMMARY Ionomers, one of the many important classes of functional polymers, are able to undergo phase separation either in solution or in the solid state. This unique property facilitates the formation of a continuous hydrophilic network for ionic transport in ionomer membranes and is the basis for the design of polymer electrolyte membranes (PEMs). Many of the PEMs in use today for fuel cells are based on the perfluorosulfonate polymers, as exemplified by the highly successful commercial ionomer Nafion®. Despite their popularity in hydrogen fuel cells, Nafion® membranes are expensive and weak against alcohol permeation, rendering them less suitable for the direct alcohol fuel cells (DAFCs). Such material issues prompted the development of lower cost alcohol resistant alternative ionomers with the desired properties for DAFC applications (high proton conductivity, low alcohol crossover, and good mechanical properties). Among them the aliphatic ionomers are low cost and can be designed to bear organic functional groups that are not solvated by alcohol molecules and hence contribute to alcohol-blocking properties. This is also the approach taken by this PhD thesis study which focused on the design and synthesis of two forms of aliphatic ionomers and investigated the properties of the membranes fabricated from them. Two different ionomer structures, namely random and block ionomers consisting of hydrophobic acrylic; and hydrophobic and hydrophilic acrylate repeating units, were synthesized by free radical polymerization (FRP) and atom transfer radical polymerization (ATRP) respectively. In-situ cross-linking was also used to inhibit alcohol permeation and to strengthen the membrane structure. vii Chapter APPENDIX PUBLICATIONS AND CONFERENCES Patents 1. D. Julius; L. Hong; J.-Y. Lee, “A Nonfluorinated Cation-Exchange Membrane based on the Self-Assembly of an Amphiphilic Diblock Oligomer and In-Situ Cross-Linking”, US provisional patent (Appl. 61/316,886), Filed on 24 March 2010. Publications 1. R.-Q. Fu; D. Julius; L. Hong; J.Y. Lee, “PPO-based acid–base polymer blend membranes for direct methanol fuel cells”, Journal of Membrane Science, 2008, 322, (2), 331-338. Conferences 1. D. Julius; L. Hong; J.Y. Lee, “Development of Aliphatic-hydrocarbon Polymer Electrolyte Membranes for Direct Ethanol Fuel Cells”, th MRS-S Conference on Advanced Materials, 17 – 19 March 2010, Institute of Materials Research and Engineering, Singapore. 2. D. Julius; L. Hong; J.Y. Lee, “Development of A Methanol Tolerant NonFluorinated Proton Exchange Membrane for Direct Ethanol Fuel Cell Applications”, 217th ECS Meeting, 25 – 30 April 2010, Vancouver, Canada. 3. D. Julius; L. Hong; J.Y. Lee, “Alcohol Tolerant Polymer Electrolyte Membranes for Low Temperature Direct Alcohol Fuel Cells”, MRS-S 148 Chapter Conference on Advances in Nanomaterials - Energy, Water and Health Care, 11 – 13 August 2010, Institute of Materials Research and Engineering, Singapore. 149 References REFERENCES Alonso, A. et al. (2001). Synthesis of amphiphilic random copolymers and fluorescence study of their association behavior in water. Macromolecular Chemistry and Physics, 202(11), 2293-2299. Anne-Claire, D. (2011). Proton exchange membranes for fuel cells operated at medium temperatures: Materials and experimental techniques. Progress in Materials Science, 56(3), 289-327. Angela, K. et al. (1987). Contribution to the study of the kinetics of radical homo- and copolymerization of fluoroalkyl methacrylates, 1. 2-chloro-2,3,3,3-tetrafluoropropyl methacrylate. Die Makromolekulare Chemie, Rapid Communications, 8(12), 621-625. Antolini, E. (2007). Catalysts for direct ethanol fuel cells. Journal of Power Sources, 170(1), 1-12. Aricò, A. S. et al. (2001). DMFCs: From fundamental aspects to technology development. Fuel Cells, 1(2), 133-161. Bai, Y. et al. (2005). Electrochemical oxidation of ethanol on Pt-ZrO2/C catalyst. Electrochemistry Communications, 7(11), 1087-1090. Battaglia, G. et al. (2005a). Effect of amphiphile size on the transformation from a lyotropic gel to a vesicular dispersion. Macromolecules, 39(2), 798-805. Battaglia, G. et al. (2005b). The evolution of vesicles from bulk lamellar gels. Nature Materials, 4(11), 869-876. Borup, R. et al. (2007). Scientific aspects of polymer electrolyte fuel cell durability and degradation. Chemical Reviews, 107(10), 3904-3951. Bose, S. et al. (2011). Polymer membranes for high temperature proton exchange membrane fuel cell: Recent advances and challenges. Progress in Polymer Science, 36(6), 813-843. Bouix, M. et al. (1998). Synthesis of amphiphilic polyelectrolyte block copolymers using “living” radical polymerization. Application as stabilizers in emulsion polymerization. Macromolecular Rapid Communications, 19(4), 209-213. Brar, A. S. et al. (1998). Acrylonitrile and glycidyl methacrylate copolymers: Nuclear magnetic resonance characterization. Macromolecules, 31(15), 4695-4702. Brar, A. S. et al. (2007). Atom transfer radical polymerization of 2-methoxy ethyl acrylate and its block copolymerization with acrylonitrile. European Polymer Journal, 43(3), 1046-1054. 150 References Braunecker, W. A. et al. (2007). Controlled/living radical polymerization: Features, developments, and perspectives. Progress in Polymer Science, 32(1), 93-146. Carmen, P. et al. (2007). Synthesis and association properties in water solution of random copolymers of 2-acrylamido-2-methyl-1-propane sulfonic acid and isodecyl methacrylate-Potential application as surfactants in micellar-enhanced ultrafiltration processes. Journal of Applied Polymer Science, 106(3), 1982-1991. Chanda, M. et al. (2007). Plastic Technology Handbook (4th ed.). Florida: Taylor & Francis Group. Chen, N. et al. (2004). Embedding poly(styrene sulfonic acid) into PVDF matrix--a new type of proton electrolyte membrane. Polymer, 45(7), 2403-2411. Chew, C. H. et al. (1998). Bicontinuous-nanostructured polymeric materials from microemulsion polymerization. Langmuir, 14(21), 6068-6076. Chen, C.-H. Et al. (1999). Preparation of methyl methacrylate and glycidyl methacrylate copolymerized nonporous particles. Journal of Polymer Science Part A: Polymer Chemistry, 37(10), 1457-1463. Chiang, W.-Y. et al. (2003). Properties of modified polyacrylonitrile membranes prepared by copolymerization with hydrophilic monomers for water-ethanol mixture separation. Journal of Applied Polymer Science, 90(1), 244-250. Chikh, L. et al. (2011). (Semi-)Interpenetrating polymer networks as fuel cell membranes. Journal of Membrane Science, 368(1-2), 1-17. Chludzinski, P. J. et al. (1971). Characteristics of hydrated sulfonated PPO reverse osmosis membranes. Abstracts of Papers of the American Chemical Society(NSEP), 46. Cho, C. G. et al. (2006). Synthesis of poly(styrene-b-styrenesulfonic acid) and its blend with PPO for proton exchange membrane. Journal of Nanoscience and Nanotechnology, 6(11), 3665-3669. Cho, J. H. et al. (2009). Fabrication and evaluation of membrane electrode assemblies by low-temperature decal methods for direct methanol fuel cells. Journal of Power Sources, 187(2), 378-386. Choi, J. et al. (2008). Nanofiber network ion-exchange membranes. Macromolecules, 41(13), 4569-4572. Chuy, C. et al. (2003). Conductivity and electrochemical ORR mass transport properties of solid polymer electrolytes containing poly(styrene sulfonic acid) graft chains. Journal of the Electrochemical Society, 150(5), E271-E279. Deluca, N. W. et al. (2006). Polymer electrolyte membranes for the direct methanol fuel cell: A review. Journal of Polymer Science Part B-Polymer Physics, 44(16), 2201-2225. 151 References Ding, J. et al. (2001). A Self-organized Network of Nanochannels Enhances Ion Conductivity through Polymer Films. Chemistry of Materials, 13(7), 2231-2233. Ding, J. et al. (2002a). Enhanced conductivity in morphologically controlled proton exchange membranes: Synthesis of macromonomers by SFRP and their incorporation into graft polymers. Macromolecules, 35(4), 1348-1355. Ding, J. et al. (2002b). Solid polymer electrolytes based on ionic graft polymers: Effect of graft chain length on nano-structured, ionic networks. Advanced Functional Materials, 12(5), 389-394. Do Kyoung, L. et al. (2008). Preparation and characterization of proton-conducting crosslinked diblock copolymer membranes. Journal of Applied Polymer Science, 107(2), 819-824. Dunwoody, D. C. et al. (2006). Current status of direct methanol fuel cell technology. In S. D. Minteer (Ed.), Alcoholic Fuels (pp. 273): Taylor & Francis Group, LLC. Eisenberg, A. et al. (1990). Polyelectrolytes and ionomers. Polymer Bulletin, 24(6), 671-671. Elabd, Y. A. et al. (2003). Triblock copolymer ionomer membranes: Part I. Methanol and proton transport. Journal of Membrane Science, 217(1-2), 227-242. Elabd, Y. A. et al. (2006). Transport properties of sulfonated poly(styrene-bisobutylene-b-styrene) triblock copolymers at high ion-exchange capacities. Macromolecules, 39(1), 399-407. Elabd, Y. A. et al. (2004). Triblock copolymer ionomer membranes: Part II. Structure characterization and its effects on transport properties and direct methanol fuel cell performance. Journal of Membrane Science, 231(1-2), 181-188. Erdogan, T. et al. (2009). Well-defined block copolymer ionomers and their blend membranes for proton exchange membrane fuel cell. Journal of Membrane Science, 344(1-2), 172-181. Findenegg, G. H. (1986). J. N. Israelachvili: Intermolecular and Surface Forces (With Applications to Colloidal and Biological Systems). Academic Press, London. Fisher, A. M. (2003). United States of America Patent No. US 6,670,403 B2. http://patents.uspto.gov/: U. S. P. a. T. Office. Fitzgerald, J. J. et al. (1988). Synthesis, properties, and structure of sulfonate ionomers. Journal of Macromolecular Science-Reviews in Macromolecular Chemistry and Physics, C28(1), 99-185. Forster, S. et al. (2001). Lyotropic phase morphologies of amphiphilic block copolymers. Macromolecules, 34(13), 4610-4623. 152 References Fu, H. Y. et al. (1994). Studies on the sulfonation of poly(phenylene oxide) (PPO) and permeation behavior of cases and water-vapor through sulfonated PPO membranes. 1. Sulfonation of PPO and characterization of the products. Journal of Applied Polymer Science, 51(8), 1399-1404. Fu, R.-Q. et al. (2008a). Membrane design for direct ethanol fuel cells: A hybrid proton-conducting interpenetrating polymer network. Fuel Cells, 8(1), 52-61. Fu, R.-Q. et al. (2008b). PPO-based acid-base polymer blend membranes for direct methanol fuel cells. Journal of Membrane Science, 322(2), 331-338. Garland, N. L. (2008). Fuel Cells. U.S. Department of Energy Retrieved from http://www.hydrogen.energy.gov/pdfs/review08/6_fuel_cells_nancy_garland.pdf. Gebel, G. (2000). Structural evolution of water swollen perfluorosulfonated ionomers from dry membrane to solution. Polymer, 41(15), 5829-5838. Gebel, G. et al. (1996). Colloidal structure of ionomer solutions in polar solvents. Journal of Molecular Structure, 383(1-3), 43-49. Gouin, J. P. et al. (1989). Microphase structure of block ionomers. 1. Study of molded styrene-4-vinylpyridinium ABA blocks by SAXS and SANS. Macromolecules, 22(12), 4573-4578. Gurau, B. et al. (2002). Methanol crossover in direct methanol fuel cells: a link between power and energy density. Journal of Power Sources, 112(2), 339-352. Hara, M. et al. (1987). Solution properties of ionomers. 1. Counterion effect. Journal of Polymer Science Part B-Polymer Physics, 25(7), 1407-1418. Hara, M. et al. (1988). Effect of intra- and intermolecular interactions on solution properties of sulfonated polystyrene ionomers. Macromolecules, 21(7), 2214-2218. Harrison, W. L. et al. (2005). Poly(arylene ether sulfone) copolymers and related systems from disulfonated monomer building blocks: Synthesis, characterization, and performance - A topical review. Fuel Cells, 5(2), 201-212. Hashidzume, A. et al. (2006). Synthesis and structural analysis of self-associating amphiphilic statistical copolymers in aqueous media. Macromolecules, 39(3), 11351143. Hashidzume, A. et al. (2002). Amphiphilic Polyelectrolyte. In S. K. Tripathy, J. Kumar & H. S. Nalwa (Eds.), Handbook of Polyelectrolytes and Their Applications (Vol. 2). California: American Scientific Publishers. Heinzel, A. et al. (1999). A review of the state-of-the-art of the methanol crossover in direct methanol fuel cells. Journal of Power Sources, 84(1), 70-74. Heitner-Wirguin, C. (1996). Recent advances in perfluorinated ionomer membranes: structure, properties and applications. Journal of Membrane Science, 120(1), 1-33. 153 References Hickner, M. A. et al. (2004). Alternative polymer systems for proton exchange membranes (PEMs). Chemical Reviews, 104(10), 4587-4611. Hickner, M. A. et al. (2005). The chemical and structural nature of proton exchange membrane fuel cell properties. Fuel Cells, 5(2), 213-229. Higashihara, T. et al. (2009). Sulfonated aromatic hydrocarbon polymers as proton exchange membranes for fuel cells. Polymer, 50(23), 5341-5357. Hillmyer, M. A. et al. (1997). Self-assembly and polymerization of epoxy resinamphiphilic block copolymer nanocomposites. Journal of the American Chemical Society, 119(11), 2749-2750. Hofmann, M. A. et al. (2002). Synthesis of polyphosphazenes with sulfonimide side groups. Macromolecules, 35(17), 6490-6493. Honma, I. et al. (2003). Organic/inorganic nano-composites for high temperature proton conducting polymer electrolytes. Solid State Ionics, 162-163, 237-245. Hsu, W. Y. et al. (1983). Ion transport and clustering in nafion perfluorinated membranes. Journal of Membrane Science, 13(3), 307-326. Huang, R. Y. M. et al. (2001). Sulfonation of poly(ether ether ketone)(PEEK): Kinetic study and characterization. Journal of Applied Polymer Science, 82(11), 2651-2660. Jagur-Grodzinski, J. (2007). Polymeric materials for fuel cells: Concise review of recent studies. Polymers for Advanced Technologies, 18(10), 785-799. Jain, S. et al. (2006). Disordered network state in hydrated block-copolymer surfactants. Physical Review Letters, 96(13), 138304. Keller, R. N. et al. (1946). Copper(I) Chloride. In W. C. Fernelius (Ed.), Inorganic Syntheses (Vol. II). New York: McGraw-Hill Book Company, Inc. Kerres, J. A. (2005). Blended and cross-linked ionomer membranes for application in membrane fuel cells. Fuel Cells, 5(2), 230-247. Khandpur, A. K. et al. (1995). Polyisoprene-polystyrene diblock copolymer phase diagram near the order-disorder transition. Macromolecules, 28(26), 8796-8806. Kim, B. et al. (2005). Morphology and transport properties of protons and methanol through partially sulfonated block copolymers. Journal of Membrane Science, 250(12), 175-182. Kim, D. S. et al. (2008a). Comb-shaped poly(arylene ether sulfone)s as proton exchange membranes. Macromolecules, 41(6), 2126-2134. Kim, J.-Y. et al. (2008b). Synthesis of microphase-separated poly(styrene-co-sodium styrene sulfonate) membranes using amphiphilic urethane acrylate nonionomers as an reactive compatibilizer. Journal of Applied Polymer Science, 107(4), 2150-2158. 154 References Kim, Y. S. et al. (2004). Sulfonated poly(arylene ether sulfone) copolymer proton exchange membranes: Composition and morphology effects on the methanol permeability. Journal of Membrane Science, 243(1-2), 317-326. Kleiner, K. (2006). Assault on batteries. Nature, 441(7097), 1046-1047. Koetz, J. et al. (2007). Polyelectrolytes and Nanoparticles. Berlin: Springer. Kreuer, K. D. (2001). On the development of proton conducting polymer membranes for hydrogen and methanol fuel cells. Journal of Membrane Science, 185(1), 29-39. Ladewig, B. P. et al. (2007). Nafion-MPMDMS nanocomposite membranes with low methanol permeability. Electrochemistry Communications, 9(4), 781-786. Lamy, C. et al. (2001). Electrocatalytic oxidation of aliphatic alcohols: Application to the direct alcohol fuel cell (DAFC). Journal of Applied Electrochemistry, 31(7), 799809. Lamy, C. et al. (2002). Recent advances in the development of direct alcohol fuel cells (DAFC). Journal of Power Sources, 105(2), 283-296. Lantman, C. W. et al. (1989). Structural properties of ionomers. Annual Review of Materials Science, 19(1), 295-317. Lantman, C. W. et al. (1987). Light scattering studies of ionomer solutions. Macromolecules, 20(5), 1096-1101. Lee, W. et al. (2008). Proton exchange membrane using partially sulfonated polystyrene-b-poly(dimethylsiloxane) for direct methanol fuel cell. Journal of Membrane Science, 320(1-2), 78-85. Leiston-Belanger, J. M. et al. (2006). Synthesis and microphase separation of poly(styrene-b-acrylonitrile) prepared by sequential anionic and ATRP techniques. Macromolecules, 39(5), 1766-1770. Li, Q. F. et al. (2003). Approaches and recent development of polymer electrolyte membranes for fuel cells operating above 100 °C. Chemistry of Materials, 15(26), 4896-4915. Li, Y. et al. (2007). Synthesis and characterization of partially fluorinated hydrophobic-hydrophilic multiblock copolymers containing sulfonate groups for proton exchange membrane. Journal of Power Sources, 172(1), 30-38. Liang, Z. X. et al. (2006). A glue method for fabricating membrane electrode assemblies for direct methanol fuel cells. Electrochimica Acta, 51(28), 6412-6418. Liaw, D. J. et al. (1997). Dilute solution properties of anionic poly(potassium-2sulfopropylmethacrylate). Journal of Applied Polymer Science, 63(2), 175-185. 155 References Lim, T. H. et al. (2007). Nano-structured proton exchange membranes molded by polymerizing bi-continuous microemulsion. Journal of Membrane Science, 290(1-2), 146-152. Lin, J. et al. (2006). Nafion-flourinated ethylene-propylene resin membrane blends for direct methanol fuel cells. Journal of the Electrochemical Society, 153(7), A1325A1331. Lin, J. et al. (2007). Stretched recast Nafion for direct methanol fuel cells. Electrochemical and Solid State Letters, 10(1), B19-B22. Ling, J. et al. (2004). Comparison of methanol crossover among four types of Nafion membranes. Journal of The Electrochemical Society, 151(10), A1604-A1610. Liu, J. G. et al. (2004). Studies on performance degradation of a direct methanol fuel cell (DMFC) in life test. Physical Chemistry Chemical Physics, 6(1), 134-137. Liu, R. C. W. et al. (2007). Impact of polymer microstructure on the self-assembly of amphiphilic polymers in aqueous solutions. Macromolecules, 40(12), 4276-4286. Loppinet, B. et al. (1998). Rodlike colloidal structure of short pendant chain perfluorinated ionomer solutions. Langmuir, 14(8), 1977-1983. Maab, H. et al. (2010). Modified SPEEK membranes for direct ethanol fuel cell. Journal of Power Sources, 195(13), 4036-4042. Maier, G. et al. (2008). Sulfonated aromatic polymers for fuel cell membranes. In G.G. Scherer (Ed.), Fuel Cells (Vol. II), (pp. 1-62), Springer. Mani, S. et al. (1999). Microstructure of ionomers based on sulfonated block copolymers of polystyrene and poly(ethylene-alt-propylene). Macromolecules, 32(11), 3663-3670. Mann, J. et al. (2006). Characterization and analysis of new catalysts for a direct ethanol fuel cell. Langmuir, 22(25), 10432-10436. Marestin, C. et al. (2008). Sulfonated Polyimides. In G.G. Scherer (Ed.), Fuel Cells (Vol. II), (pp. 185-258), Springer. Masci, G. et al. (2004). Atom transfer radical polymerization of potassium 3sulfopropyl methacrylate: Direct synthesis of amphiphilic block copolymers with methyl methacrylate. Macromolecules, 37(12), 4464-4473. Matyjaszewski, K. et al. (1997). Synthesis of well-defined polyacrylonitrile by atom transfer radical polymerization. Macromolecules, 30(20), 6398-6400. Matyjaszewski, K. et al. (1999). An investigation into the CuX/2,2'-Bipyridine (X = Br or Cl) mediated atom transfer radical polymerization of acrylonitrile. Macromolecules, 32(20), 6431-6438. 156 References Matyjaszewski, K. et al. (2001). Atom transfer radical polymerization. Chemical Reviews, 101(9), 2921-2990. Mauritz, K. A. et al. (2004). State of understanding of Nafion. Chemical Reviews, 104(10), 4535-4586. Mehta, V. et al. (2003). Review and analysis of PEM fuel cell design and manufacturing. Journal of Power Sources, 114(1), 32-53. Meier-Haack, J. et al. (2005). Membranes from sulfonated block copolymers for use in fuel cells. Separation and Purification Technology, 41(3), 207-220. Minteer, S. D. (2006). Direct Ethanol Fuel Cells. In S. D. Minteer (Ed.), Alcoholic Fuels (pp. 191-202). FL: Taylor & Francis Group, LLC. Moffitt, M. et al. (1996). Micellization of ionic block copolymers. Accounts of Chemical Research, 29(2), 95-102. Muldoon, J. et al. (2009). High performance fuel cell operation with a non-fluorinated polyphosphazene electrode binder. Fuel Cells, 9(5), 518-521. Neburchilov, V. et al. (2007). A review of polymer electrolyte membranes for direct methanol fuel cells. Journal of Power Sources, 169(2), 221-238. Ng, W. K. et al. (1999). Evaluation of intrinsic viscosity measurements of hydrophobically modified polyelectrolyte solutions. European Polymer Journal, 35(7), 1245-1252. Nomula, S. et al. (1998). Hydrophobic aggregation in polyurethane ionomer solutions. Journal of Colloid and Interface Science, 205(2), 331-339. Nomula, S. et al. (2001). Effect of solvent polarity in ionomer solutions. Macromolecules, 34(4), 925-930. Noritaka, O. et al. (1994). Solution viscosity behavior of polystyrene-based cationic ionomers. Effects of ion content and solvent. Journal of Polymer Science Part A: Polymer Chemistry, 32(13), 2589-2595. Norsten, T. B. et al. (2006). Highly fluorinated comb-shaped copolymers as proton exchange membranes (PEMs): Improving PEM properties through rational design. Advanced Functional Materials, 16(14), 1814-1822. Odian, G. (2004). Principles of Polymerization (Fourth ed.). New Jersey: John Wiley & Sons, Inc. Okamura, H. et al. (2002). Synthesis of random and block copolymers of styrene and styrenesulfonic acid with low polydispersity using nitroxide-mediated living radical polymerization technique. Polymer, 43(11), 3155-3162. 157 References Patten, T. E. et al. (1998). Atom transfer radical polymerization and the synthesis of polymeric materials. Advanced Materials, 10(12), 901-915. Pei, H. et al. (2006a). Embedded polymerization driven asymmetric PEM for direct methanol fuel cells. Journal of Membrane Science, 270(1-2), 169-178. Pei, H. et al. (2006b). Polymer electrolyte membrane based on 2-acrylamido-2-methyl propanesulfonic acid fabricated by embedded polymerization. Journal of Power Sources, 160(2), 949-956. Pei, H. et al. (2006c). Polymer electrolyte membranes based on crosslinked amphiphilic copolymers of 3-sulfopropyl methacrylate. PhD dissertation, National University of Singapore, Singapore. Pei, H. et al. (2007). Embedded hydrophilic nanogranules with radiating protonconducting channels in a hydrophobic matrix. Langmuir, 23(9), 5077-5084. Peinemann, K.-V. et al. (2007). Asymmetric superstructure formed in a block copolymer via phase separation. Nature Materials, 6(12), 992-996. Pethkar, S. et al. (2001). Evidence for second-order optical nonlinearity in gamma-ray induced partially cross-linked polyacrylonitrile. Journal of Physical Chemistry B, 105(22), 5110-5113. Pivovar, B. S. et al. (1999). Pervaporation membranes in direct methanol fuel cells. Journal of Membrane Science, 154(2), 155-162. Qi, Z. et al. (2002). Open circuit voltage and methanol crossover in DMFCs. Journal of Power Sources, 110(1), 177-185. Qian, W. M. et al. (2006). Architecture for portable direct liquid fuel cells. Journal of Power Sources, 154(1), 202-213. Qiu, J. et al. (2001). Controlled/living radical polymerization in aqueous media: Homogeneous and heterogeneous systems. Progress in Polymer Science, 26(10), 2083-2134. Raihane, M. et al. (2006). Radical copolymerization of 2,2,2-trifluoroethyl methacrylate with cyano compounds for dielectric materials: Synthesis and characterization. Journal of Fluorine Chemistry, 127(3), 391-399. Ramaiyan, K. et al. (2008). Polymer electrolyte fuel cells using Nafion-based composite membranes with functionalized carbon nanotubes. Angewandte Chemie International Edition, 47(14), 2653-2656. Ren, X. et al. (2000a). Water and methanol uptakes in Nafion membranes and membrane effects on direct methanol cell performance. Journal of The Electrochemical Society, 147(1), 92-98. 158 References Ren, X. et al. (2000b). Methanol transport through Nation membranes. Electroosmotic drag effects on potential step measurements. Journal of The Electrochemical Society, 147(2), 466-474. Rhim, J.-W. et al. (2004). Crosslinked poly(vinyl alcohol) membranes containing sulfonic acid group: Proton and methanol transport through membranes. Journal of Membrane Science, 238(1-2), 143-151. Riess, G. (2003). Micellization of block copolymers. Progress in Polymer Science, 28(7), 1107-1170. Rikukawa, M. et al. (2000). Proton-conducting polymer electrolyte membranes based on hydrocarbon polymers. Progress in Polymer Science, 25(10), 1463-1502. Ritzenthaler, S. et al. (2002). ABC triblock copolymers/epoxy-diamine blends. 2. Parameters controlling the morphologies and properties. Macromolecules, 36(1), 118126. Robinson, K. L. et al. (2001). Controlled polymerization of 2-hydroxyethyl methacrylate by ATRP at ambient temperature. Macromolecules, 34(10), 3155-3158. Rochas, C. et al. (1979). Polyelectrolyte behaviour of acrylonitrile methallylsulphonate copolymers in dimethylformamide. Polymer, 20(1), 76-80. Roelofs, K. S. et al. (2010). Sulfonated poly(ether ether ketone)-based silica nanocomposite membranes for direct ethanol fuel cells. Journal of Membrane Science, 346(1), 215-226. Roland-Swanson, C. et al. (2004). Polymerization of sulfopropyl methacrylate, a surface active monomer, within layered double hydroxide. Chemistry of Materials, 16(25), 5512-5517. Rubatat, L. et al. (2008). Structure-properties relationship in proton conductive sulfonated polystyrene-polymethyl methacrylate block copolymers (sPS-PMMA). Macromolecules, 41(21), 8130-8137. Rusanov, A. et al. (2008). Proton-conducting polymers and membranes carrying phosphonic acid groups. In G.G. Scherer (Ed.), Fuel Cells (Vol. II), (pp. 125-155), Springer. Rushing, T. S. et al. (2003). Intrinsic viscosity dependence on polymer molecular weight and fluid temperature. Journal of Applied Polymer Science, 89(10), 28312835. Sacca, A. et al. (2005). Nafion-TiO2 hybrid membranes for medium temperature polymer electrolyte fuel cells (PEFCs). Journal of Power Sources, 152(1), 16-21. Sahu, A. K. et al. (2009). Novel organic-inorganic composite polymer-electrolyte membranes for DMFCs. Journal of Membrane Science, 345(1-2), 305-314. 159 References Saito, M. et al. (2006). Alcohol and proton transport in perfluorinated ionomer membranes for fuel cells. Journal of Physical Chemistry B, 110(48), 24410-24417. Schmidt-Rohr, K. et al. (2008). Parallel cylindrical water nanochannels in Nafion fuel-cell membranes. Nature Materials, 7(1), 75-83. Serpico, J. M. et al. (2002). Transport and structural studies of sulfonated styreneethylene copolymer membranes. Macromolecules, 35(15), 5916-5921. Shao, Z.-G. et al. (2002). Composite Nafion/polyvinyl alcohol membranes for the direct methanol fuel cell. Journal of Membrane Science, 210(1), 147-153. Shuqin, S. et al. (2007). How far are direct alcohol fuel cells from our energy future? Journal of Fuel Cell Science and Technology, 4(2), 203-209. Siadat, B. et al. (1981). Solubility behavior of copolymers of isoprene and sodium styrenesulfonate. Macromolecules, 14(3), 773-776. Smart, T. et al. (2008). Block copolymer nanostructures. Nano Today, 3(3-4), 38-46. Smitha, B. et al. (2003). Synthesis and characterization of proton conducting polymer membranes for fuel cells. Journal of Membrane Science, 225(1-2), 63-76. Song, S. et al. (2006). Recent progress in direct ethanol proton exchange membrane fuel cells (DE-PEMFCs). Applied Catalysis B: Environmental, 63(3-4), 187-193. Song, S. et al. (2005). Ethanol crossover phenomena and its influence on the performance of DEFC. Journal of Power Sources, 145(2), 266-271. Staiti, P. et al. (2001). Hybrid Nafion-silica membranes doped with heteropolyacids for application in direct methanol fuel cells. Solid State Ionics, 145(1-4), 101-107. Steele, B. C. H. et al. (2001). Materials for fuel-cell technologies. Nature, 414(6861), 345-352. Tan, A. R. et al. (2006). Nanocomposite membranes based on sulfonated poly(etheretherketone) structured with modified silica for direct ethanol fuel cell. Macromolecular Symposia, 245, 470-475. Tan, N. et al. (2010a). Synthesis and properties of sulfonated polybenzothiazoles with benzimidazole moieties as proton exchange membranes. Journal of Membrane Science, 356(1-2), 70-77. Tan, N. et al. (2010b). Preparation and properties of polybenzimidazoles with sulfophenylsulfonyl pendant groups for proton exchange membranes. Journal of Membrane Science, 353(1-2), 51-59. Tanford, C. (1973). The Hydrophobic Effect: Formation of Micelles and Biological Membranes (First ed.). New York: John Wiley & Sons Inc. 160 References Tang, C. B. et al. (2003). Preparation of polyacrylonitrile-block-poly(n-butyl acrylate) copolymers using atom transfer radical polymerization and nitroxide mediated polymerization processes. Macromolecules, 36(5), 1465-1473. Tant, M. R. et al. (1988). An overview of the viscous and viscoelastic behavior of ionomers in bulk and solution. Polymer Reviews, 28(1), - 63. Thomas, G. (2000). Overview of storage development DOE hydrogen program. US DOE Hydrogen Program Review, 14. Retrieved from http://www1.eere.energy.gov/hydrogenandfuelcells/pdfs/storage.pdf Tsai, C.-E. et al. (2010). A novel crosslinking strategy for preparing poly(vinyl alcohol)-based proton-conducting membranes with high sulfonation. Journal of Power Sources, 195(8), 2166-2173. Tsang, E. M. W. et al. (2007). Considerations of macromolecular structure in the design of proton conducting polymer membranes: Graft versus diblock polyelectrolytes. Journal of the American Chemical Society, 129(49), 15106-15107. Tsarevsky, N. V. et al. (2007). Green atom transfer radical polymerization: From process design to preparation of well-defined environmentally friendly polymeric materials. Chemical Reviews, 107(6), 2270-2299. Vigier, F. et al. (2006). Electrocatalysis for the direct alcohol fuel cell. Topics in Catalysis, 40(1-4), 111-121. Wang, H. et al. (2007). Pd nanowire arrays as electrocatalysts for ethanol electrooxidation. Electrochemistry Communications, 9(5), 1212-1216. Wang, J. et al. (1991). Light scattering and small-angle x-ray scattering studies of an ionomer poly(styrene-sodium-2-(acrylamido)-2-methylpropanesulfonate) in polar solvents. Macromolecules, 24(3), 790-798. Weiss, R. A. et al. (1985). Sulfonated polystyrene ionomers prepared by emulsion copolymerization of styrene and sodium styrene sulfonate. Journal of Polymer Science: Polymer Chemistry Edition, 23(2), 525-533. Wojciech, K. et al. (1992). Infrared investigations of sulfonated ionomer membranes. I. Water-alcohol compositions and counterions effects. Journal of Applied Polymer Science, 44(6), 951-958. Woo, Y. et al. (2003). Synthesis and characterization of sulfonated polyimide membranes for direct methanol fuel cell. Journal of Membrane Science, 220(1-2), 3145. Wu, D. et al. (2006). Aqueous-core capsules via interfacial free radical alternating copolymerization. Macromolecules, 39(17), 5848-5853. 161 References Wu, J. L. et al. (1994). Light scattering study of ionomer solutions. 3. Dynamic scattering from sulfonated polystyrene ionomers in a polar solvent (dimethylformamide). Macromolecules, 27(4), 923-929. Wycisk, R. et al. (2006). Direct methanol fuel cell membranes from Nafionpolybenzimidazole blends. Journal of Power Sources, 163(1), 9-17. Wycisk, R. et al. (1996). Sulfonated polyphosphazene ion-exchange membranes. Journal of Membrane Science, 119(1), 155-160. Xue, Y. et al. (2010). Acid-base hybrid polymer electrolyte membranes based on SPEEK. Journal of Membrane Science, 350(1-2), 148-153. Yamaguchi, T. et al. (2007). An extremely low methanol crossover and highly durable aromatic pore-filling electrolyte membrane for direct methanol fuel cells. Advanced Materials, 19(4), 592-596. Yamanaka, J. et al. (1990). Revisit to the intrinsic viscosity-molecular weight relationship of ionic polymers. 2. Viscosity behavior of salt-free aqueous solutions of sodium poly(styrenesulfonates). Journal of the American Chemical Society, 112(2), 587-592. Yameen, B. et al. (2008). Facile large-scale fabrication of proton conducting channels. Journal of the American Chemical Society, 130(39), 13140-13144. Yang, B. et al. (2004a). Multilayered membranes with suppressed fuel crossover for direct methanol fuel cells. Electrochemistry Communications, 6(3), 231-236. Yang, C. C. et al. (2008a). Preparation of a PVA/HAP composite polymer membrane for a direct ethanol fuel cell (DEFC). Journal of Applied Electrochemistry, 38(10), 1329-1337. Yang, H. et al. (2004b). A novel method for determining the viscosity of polymer solution. Polymer Testing, 23(8), 897-901. Yang, Y. et al. (2005). Synthetic strategies for controlling the morphology of proton conducting polymer membranes. Fuel Cells, 5(2), 171-186. Yang, Y. et al. (2008b). Structural and morphological features of acid-bearing polymers for PEM fuel cells. In G.G. Scherer (Ed.), Fuel Cells (Vol. I), (pp. 55-126), Springer. Yeager, H. L. et al. (1982). Introduction. In A. Eisenberg & H. L. Yeager (Eds.), Perfluorinated Ionomer Membranes. Washington, D.C.: American Chemical Society. Yoshitake, M. et al. (2008). Perfluorinated Ionic Polymers for PEFCs (Including Supported PFSA) Fuel Cells I, 127-155. Young, A. M. et al. (1998). Dynamic light scattering and rheology of associating sulfonated polystyrene ionomers in non-polar solvents. Polymer, 39(8-9), 1525-1532. 162 References Young, A. M. et al. (1996). Effect of aggregation on the single-chain dimensions of sulfonated polystyrene ionomers in xylene. Polymer, 37(11), 2125-2130. Yu, K. et al. (1996). Multiple morphologies in aqueous solutions of aggregates of polystyrene-block-poly(ethylene oxide) diblock copolymers. Macromolecules, 29(19), 6359-6361. Yu, Y. S. et al. (1997). Control of morphology through polymer-solvent interactions in crew-cut aggregates of amphiphilic block copolymers. Journal of the American Chemical Society, 119(35), 8383-8384. Zawodzinski, T. A. et al. (1991). Determination of water diffusion coefficients in perfluorosulfonate ionomeric membranes. Journal of Physical Chemistry, 95(15), 6040-6044. Zhang, L. F. et al. (1997). Phase separation behavior and crew-cut micelle formation of polystyrene-b-poly(acrylic acid) copolymers in solutions. Macromolecules, 30(4), 1001-1011. Zhou, Z. et al. (1993). Block copolymer ionomers: solution behavior of lightly sulfonated polystyrene-b-poly(tert-butylstyrene) in polar solvent. Macromolecules, 26(11), 2968-2973. Zoppi, R. A. et al. (1998). Electrochemical impedance studies of hybrids of perfluorosulfonic acid ionomer and silicon oxide by sol-gel reaction from solution. Journal of Electroanalytical Chemistry, 445(1-2), 39-45. 163 [...]... will focus on perfluorosulfonate membranes such as Nafion® and their modifications; as well as hydrocarbon membranes based on aromatic and aliphatic ionomers The second half of this chapter looks at the ionomers for PEM applications in greater detail, in particular the synthesis and phase separation of random and blocks ionomers in solution and in the solid state It is noteworthy to mention that phase... trade-off between conductivity and mechanical properties The benefits of the TFPM modification on PEM properties were investigated through a series of microstructure characterizations (b) Structural Characterizations of Random Aliphatic Ionomers and Investigations of the Effects of Hydrophobic Functional Groups on Phase Separation in Solution The inclusion of hydrophobic TFPM in the random ionomer... of this thesis study includes the following: (a) Design and Synthesis of New Alcohol-Resistant Alternative PEMs based on Aliphatic Random Ionomers New aliphatic random ionomers consisting of hydrophobic (AN-GMA) and ionic (SPM) units were synthesized by a simple solution polymerization method and cast into freestanding membranes The PEM design was predicated based on the low solubility of acrylic polymers... secondary channels expanded the connectivity of the primary hydrophilic channels and consequently increased the proton conductivity without loss of mechanical integrity and fuel crossover resistance 6 Chapter 1 (d) Investigations of a One-pot ATRP Method and the Phase Separation of Aliphatic Block Ionomers in Solution The synthesis of the aliphatic diblock ionomers in (c) was based on a one-pot ATRP method... polymerization (□), after 6h of polymerization (■), after 6h of polymerization (▲) 80 Figure 4.8 UV-Vis spectra of (SPM-GMA-TFPM) monomer mixture in DMF before polymerization (□), after 1h of polymerization (■), after 6h of polymerization (▲) 81 Figure 4.9 UV-Vis spectra (at the λmax of AN) of the two copolymerization systems before and after 6 h of copolymerization: the monomer mixture S0-10 (○) and. .. initial ionomer concentration was 1 wt.% 78 Figure 4.5 UV-Vis spectra of AN monomer in DMF before polymerization (□), after 1h of polymerization (■), after 6h of polymerization (▲) 79 Figure 4.6 UV-Vis spectra of GMA monomer in DMF before polymerization (□), after 1h of polymerization (■), after 6h of polymerization (▲) 80 Figure 4.7 UV-Vis spectra of TFPM monomer in DMF before polymerization... random ionomers and to deduce the origin of the benevolent effects of TFPM modification (c) Development of New PEMs based on Aliphatic Block Ionomers and Hydrophilic Covalent Cross-links The design of low-cost aliphatic ionomers membranes must successfully address the trade-off between proton conductivity and mechanical strength In this part of the study, a new approach which combines an ordered polymer. .. intensities as a function of H2O addition to the DMSO solution of P(AN-co-GMA)-b-SPM diblock ionomers: A50G4S-10 ionomer/DMSO (A), A100G4S-10 ionomer/DMSO (B), A150G4S-10 ionomer/DMSO (C) 135 Figure 6.7 Size distribution of aggregates formed upon water dilution of the DMSO solution Comparisons between the A50G4 copolymer, blend of the A50G4 copolymer and hydrophilic P(SPM) ionomer, and the A 50G4S-10... the miscibility problem of hydrophobic and ionic monomers due to the lack of a good common solvent The last part of this thesis study examined the details of the one-pot synthesis and the structures of the diblock ionomers Structural characterizations of the ionomers by Fourier-transform-infrared (FT-IR) spectroscopy, transmission electron microscopy (TEM) and zeta-potential and light-scattering measurements... membrane as a function of sulfonation degree (A) DMFC performance benchmarked against a Nafion® 115 membrane (B) (Lee et al., 2008) 20 Figure 2.8 A PEM design based on ionic cross-linking of aliphatic diblock ionomers (A), and its proton conductivity as a function of the weight fraction of SA (B) (Do Kyoung et al., 2008) 23 Figure 2.9 Organization of amphiphilic block ionomers in a selective . Separation of Random and Block Ionomers in Solution 33 2.3.2.2 Phase Separation of Random and Block Ionomers in the Solid State 36 SYNTHESIS AND CHARACTERIZATION OF ACRYLIC RANDOM- IONOMER MEMBRANES. on Aliphatic Random Ionomers 5 (b) Structural Characterizations of Random Aliphatic Ionomers and Investigations of the Effects of Hydrophobic Functional Groups on Phase Separation in Solution. SYNTHESIS AND CHARACTERIZATIONS OF POLYMER ELECTROLYTE MEMBRANES BASED ON ALIPHATIC IONOMERS DAVID JULIUS 2011 SYNTHESIS AND CHARACTERIZATIONS OF