Impact performance of cement composite filled pipe in pipe structures

IMPACT PERFORMANCE OF CEMENT COMPOSITE FILLED PIPE-IN-PIPE STRUCTURES WANG YU NATIONAL UNIVERSITY OF SINGAPORE 2014 IMPACT PERFORMANCE OF CEMENT COMPOSITE FILLED PIPE-IN-PIPE STRUCTURES WANG YU (B. Eng., HIT) A THESIS SUBMITTED FOR THE DEGREE OF DOCTOR OF PHILOSOPHY DEPARTMENT OF CIVIL & ENVIRONMENTAL ENGINEERING NATIONAL UNIVERSITY OF SINGAPORE 2014 DECLARATION I hereby declare that this thesis is my original work and it has been written by me in its entirety. I have duly acknowledged all the sources of information which have been used in the thesis. This thesis has also not been submitted for any degree in any university previously. Wang Yu 01 August 2014 Acknowledgement ACKNOWLEDGEMENT I wish to express my sincerest gratitude to my supervisors Professor Liew Jat Yuen, Richard, Professor Zhang Min-Hong and Associate Professor Qian Xudong for their invaluable support, guidance and encouragement on my research work. Sincere thanks are further expressed to Dr. Chia Kok Seng, Dr. Kazi Md Abu Sohel, Dr. Lee Siew Chin, Dr. Wang Tongyun, Dr. Xiong Dexin, Dr. Xiong Mingxiang, Dr. Yan Jiabao and Ms. Zheng Jiexin for their help in my research work. Thanks are also extended to all staff members at Concrete and Structural Engineering Laboratory for their generous, patient and continuous help during the experiments. I would also like to thank all friends and colleagues in National University of Singapore during the past four years for sharing with me their happiness. Special thanks to my parents and girlfriend for their moral supports, continuous love, understanding and encouragement. Finally, I would like to acknowledge the finiancial support from the Center for Offshore Research and Engineering in the National University of Singapore and the research scholarship provided by the China Scholarship Council. i Table of contents TABLE OF CONTENTS ACKNOWLEDGEMENT . i TABLE OF CONTENTS ii SUMMARY . vi LIST OF TABLES . viii LIST OF FIGURES x LIST OF SYMBOLS . xvii CHAPTER ONE INTRODUCTION 1.1 Background . 1.2 Objectives and Scopes . 1.3 Significance and Contributions . 1.4 Outline of the Thesis . CHAPTER TWO LITERATURE REVIEW 2.1 Introduction . 2.2 Hollow Steel Pipes Subjected to Transverse Loads 2.2.1 Hollow Steel Pipes Subjected to Static Transverse Loads 2.2.2 Hollow Steel Pipes Subjected to Transverse Impacts . 14 2.2.3 Indentation Limits for Hollow Steel Pipes 21 2.3 Steel-Concrete-Steel (SCS) Composite Panels Subjected to Transverse Loads . 23 2.4 Concrete-Filled Steel Tubes (CFST) Subjected to Transverse Loads . 28 2.4.1 Concrete-Filled Steel Tubes (CFST) Subjected to Static Transverse Loads . 28 2.4.2 Concrete-Filled Steel Tubes (CFST) Subjected to Transverse Impacts 32 2.5 Concrete-Filled Pipe-In-Pipe Composite Structures . 36 2.6 Filler Materials for Composite Structures . 41 2.7 Observations Arising from the Literature Review 43 ii Table of contents CHAPTER THREE DROP WEIGHT IMPACT TEST 3.1 Introduction 46 3.2 Test Specimens and Set-up 47 3.2.1 Test Specimens 47 3.2.2 Ultra Lightweight Cement Composite (ULCC) . 49 3.2.3 Test Set-up and Test Procedure . 51 3.3 Test Results and Discussion 55 3.3.1 Damage Mechanisms . 57 3.3.2 Impact Force 59 3.3.3 Global Displacement 62 3.3.4 Local Indentation . 64 3.3.5 Strains 67 3.3.6 Post-peak Mean Force 72 3.3.7 Global Bending Deformation Energy 74 3.3.8 Energy Absorption Capacity 75 3.3.9 Effects of PVA Fibers 77 3.3.10 Comparison of the Impact Performance 79 3.3.11 Multiple Impacts 79 3.4 Summary 84 CHAPTER FOUR FINITE ELEMENT ANALYSIS 4.1 Introduction 87 4.2 Finite Element Modeling . 88 4.2.1 Material Models . 88 4.2.2 Finite Element Models . 92 4.2.3 Contact Model 94 4.3 Validation of Finite Element Analysis . 95 4.4 Finite Element Parametric Study . 101 iii Table of contents 4.4.1 Impact Velocity Effect 102 4.4.2 Indenter Shape Effect 104 4.4.3 Inner Pipe Effect 107 4.4.4 Steel Strength Effect 108 4.4.5 Cement Composite Strength Effect . 110 4.4.6 Filler Material Effect . 112 4.5 Summary . 113 CHAPTER FIVE LOAD-INDENTATION RELATIONSHIP 5.1 Introduction . 115 5.2 Experimental Investigation 116 5.2.1 Test Specimens and Set-up 116 5.2.2 Test Results . 118 5.2.3 Comparison with Analytical Models for Hollow Pipes . 123 5.3 Finite Element Investigation . 125 5.3.1 Finite Element Modeling . 125 5.3.2 Validation of the FE Analysis . 126 5.4 Load-Indentation Relationship for Hollow Pipes 129 5.5 Two-Stage Load-Indentation Formulation for Pipe-In-Pipe Composite Structures 131 5.5.1 Theoretical Model for Hollow Pipes . 131 5.5.1.1 Ring model 133 5.5.1.2 Generator model 135 5.5.1.3 P-δ relationship for hollow pipes 137 5.5.2 Two-Stage Approach for Cement Composite Filled Pipe-In-Pipe Structures . 137 5.5.2.1 Composite stage . 138 5.5.2.2 Separation stage . 142 5.5.3 Validation 143 5.6 Load-Indentation Relationship for Cement Composite Filled Pipes . 147 5.6.1 Localized Indentation Phase 147 iv Table of contents 5.6.2 Indentation Propagation Phase . 149 5.6.3 Load Redistribution Phase . 150 5.6.4 Validation . 153 5.7 Summary 154 CHAPTER SIX THEORETICAL ANALYSIS 6.1 Introduction 157 6.2 Theoretical Analysis 158 6.2.1 Dynamic Deformation Response . 158 6.2.2 Load-Indentation Relationships for Simply Supported Pipes 163 6.2.3 Numerical Procedure . 166 6.3 Validation of Theoretical Analysis 169 6.4 Parametric Study 176 6.4.1 Material Strength Effect . 176 6.4.2 Geometric Property and Impact Velocity Effect 180 6.4.3 Validation against Numerical Simulations . 185 6.4.4 Simplified Impact Response Formulation for Pipe-In-Pipe Composite Structure . 188 6.5 Summary 192 CHAPTER SEVEN CONCLUSIONS 7.1 Brief Overview 194 7.2 Main Findings and Conclusions 196 7.3 Recommendations for Future Research . 203  REFERENCE . 204 LIST OF PUBLICATIONS 218 v Summary SUMMARY Circular hollow sections have wide applications in both onshore and offshore infrastructures, including offshore jacket and jackup structures, oil and gas pipelines, etc., due to their low resistance to fluid flow, easy handling in construction, transportation and erection. Protection of pipelines against impact loadings has become an important concern in engineering as external impact loadings are a primary threat and a frequent cause of damage in onshore and offshore pipelines. Most of the current studies on this problem have focused on the impact performance of hollow steel pipes, which demonstrate limited structural capacity under impact loads, coupled with large global and local deformations. Concrete-filled pipe-in-pipe composite structures have recently emerged as a popular solution to enhance the structural resistance against external loadings. Engineering applications of such composite structures in a harsh offshore environment requires a comprehensive understanding on the impact behavior for these pipe-in-pipe composite structures. The objective of this research is, therefore, to develop a framework to predict the impact response of ultra lightweight cement composite (ULCC) filled pipe structures, validated by detailed experimental and numerical investigations. This study carries out drop weight impact tests to investigate the impact behavior for three types of pipe specimens, including hollow pipe specimens, ULCC-filled pipe specimens and ULCC-filled pipe-in-pipe specimens. Besides the experimental investigation, this study simulates the impact process for the pipe specimens by using the nonlinear finite element (FE) software LS-DYNA and conducts an FE parametric study to extend the understanding of the impact performance for pipe-in-pipe composite structures. The pipe specimens experience global deformations and local indentations under the transverse impact. This study conducts lateral indentation tests to explore the load-indentation (P-δ) vi Conclusions 7.3 Recommendations for Future Research The following are further research work recommended to achieve an insight into the impact behavior of pipe-in-pipe composite structures: (1) Research work investigates the impact behavior for pipe-in-pipe composite structures under the combined transverse impacts and various levels of external or internal pressure to simulate the working condition of pipelines in the offshore environment. (2) Research work investigates the impact behavior for pipe-in-pipe composite structures subjected to the combined transverse impacts and axial pre-loads to simulate the working condition of onshore and offshore pipelines. (3) Experimental study focuses on the ultra lightweight cement composite (ULCC) through bending tests, biaxial and triaxial compressive test, etc., to improve the understanding of the material behavior and to develop the material model for the ULCC in the finite element (FE) analysis. (4) In the current study, the cement composite strength and the inner steel pipe thickness demonstrate slight influence on the impact performance for the pipe-in-pipe composite structures than the outer pipe strength and its thickness. Research work may explore the impact behavior for pipe-in-pipe composite structure filled with more lightweight materials than the ULCC and utilize FRP inner pipe to further reduce the structural weight. 203 References REFERENCE AIJ. Standards for Structural Calculation of Steel Reinforced Concrete Structures. Tokyo: Architectural Institute of Japan. 1987. AIJ. Recommendations for Design and Construction of Concrete Filled Steel Tubular Structures. Tokyo: Architectural Institute of Japan. 1997. AISC-LRFD. Manual of Steel Construction, Load and Resistance Factor Design, (Including Commentary). Chicago: AISC. 2003. Al-Thairy, H. and Wang, Y.C. A Numerical Study of the Behaviour and Failure Modes of Axially Compressed Steel Columns Subjected to Transverse Impact, Int J Impact Eng, 38(8-9), pp. 732-744. 2011. An, C., Castello, X., Duan, M., Filho, R.D.T. and Estefen, S.F. Ultimate Strength Behavior of Sandwich Pipes Filled with Steel Fiber Reinforced Concrete, Ocean Eng, 55(1), pp. 125-135. 2012. Arabzadeh, H. and Zeinoddini, M. Dynamic Response of Pressurized Submarine Pipelines Subjected to Transverse Impact Loads, Procedia Eng, 14, pp. 648-655. 2011. Arabzadeh, H. and Zeinoddini, M. A Close-Form Solution for Lateral Indentation of Pressurized Pipes Resting on A Flexible Bed, Int J Mech Sci, 75, pp. 189-199. 2013. Arjomandi, K. and Taheri, F. A New Look at the External Pressure Capacity of Sandwich Pipes, Mar Struct, 24(1), pp. 23-42. 2011. AS 4100. Australian Standard, Steel Structures. Standards Australia, Sydney (Australia). 1998. AS 5100. Australian Standard, Bridge Design, Part 6: Steel and Composite Construction. Standards Australia, Sydney (Australia). 2007. ASTM E8/E8M. Standard test methods for tension testing of metallic materials. American Society of Testing and Material (ASTM) International. 2011. Bambach, M.R. Design of Hollow and Concrete Filled Steel and Stainless Steel tubular Columns for Transverse Impact Loads, Thin-Walled Struct, 49(10), pp. 1251-1260. 2011. Bambach, M.R., Jama, H., Zhao, X.L. and Grzebieta, R.H. Effect of Concrete Filling Steel Hollow Section Beams under Transverse Impact Loads. In Proc. 7th International Conference on Shock & Impact Loads on Structures, October 2007, Beijing, China. pp. 123-130. Bambach, M.R., Jama, H., Zhao, X.L. and Grzebieta, R.H. Hollow and Concrete Filled Steel Hollow Sections under Transverse Impact Loads, Eng Struct, 30(10), pp. 2859-2870. 2008. 204 References Batzias, F.A., Siontorou, C.G. and Spanidis, P.-M.P. Designing a Reliable Leak Bio-Detection System for Natural Gas Pipelines, J Hazard Mater, 186(1), pp. 35-58. 2011. Bouzaiene, A. and Massicotte, B. Hypoelastic Tridimensional Model for Nonproportional Loading of Plain Concrete, J Eng Mech, ASCE, 123(11), pp. 1111-1120. 1997. Brockenbrough, R.L. and Merritt, F.S. Structural Steel Designer’s Handbook: AISC, AASHTO, AISI, ASTM and ASCE-07 Design Standards. New York, NY: Mcgraw, Inc. 2006. Brooker, D.C. Numerical Modeling of Pipeline Puncture under Excavator Loading. Part I. Development and Validation of A Finite Element Material Failure Model for Puncture Simulation, Int J Pressure Vessels Pip, 80(10), pp. 715-725. 2003. Brooker, D.C. Numerical Modeling of Pipeline Puncture under Excavator Loading. Part II. Parametric Study, Int J Pressure Vessels Pip, 80(10), pp. 727-735. 2003. Brooker, D.C. A Numerical Study on the Lateral Indentation of Continuously Supported Tubes, J of Constr Steel Res, 60(8), pp. 1177-1192. 2004. Brooker, D.C. Denting of Pressurized Pipelines under Localized Radial Loading, Int J Mech Sci, 46(12), pp. 1783-1805. 2004. BS 5400, Part 2. Steel, Concrete and Composite Bridges, Specification for Loads. British Standard Institution. 2006. BS 5400, Part 5. Steel, Concrete and Composite Bridges, Code of Practice for Design of Composite Bridges. British Standard Institution. 2005. Cantwell, W.J. and Morton, J. The Impact Resistance of Composite Materials-A Review. Composites, 22(5), pp. 347-362. 1991. CEB Comité Euro-International du Béton. CEB-FIP Model Code 1990. Trowbridge, Wiltshire, UK: Redwood Books. 1993. Chen, K. and Shen, W.Q. Further Experimental Study on the Failure of Fully Clamped Steel Pipes, Int J Impact Eng, 21(3), pp. 177-202. 1998. Chen, W.F. Constitutive Equations for Engineering Materials: Vol. 2-Plasticity and Modeling. Elsevier, Amsterdam. 1994. Chia, K.S., Zhang, M.H. and Liew, J.Y.R. High-Strength Ultra Lightweight Cement Composite Material Properties. In Proc. 9th International Symposium on High Performance Concrete-Design, Verification & Utilization, Aug 2011, Rotorua, New Zealand, Primary Session A8-paper 2. CIDECT. Design Guide for Concrete Filled Hollow Section Columns under Static and Seismic Loading. Bergmann, R., matsui, C., Meinsama, C. and Dutta, D. Germany: TUV-Verlag. 1995. 205 References Clubley, S.K., Moy, S.S.J. and Xiao, Y.R. Shear Strength of Steel-Concrete-Steel Composite Panels. Part I-Testing and Numerical Modelling, J Constr Steel Res, 59(6), pp. 781-794. 2003. Clubley, S.K., Moy, S.S.J. and Xiao, Y.R. Shear Strength of Steel-Concrete-Steel Composite Panels. Part II-Detailed Numerical Modelling of Performance, J Constr Steel Res, 59(6), pp. 795-808. 2003. Corbett, G.G. and Reid, S.R. Local Loading of Simply-Supported Steel-Grout Sandwich Plates, Int J Impact Eng, 13(3), pp. 443-461. 1993. Corbett, G.G., Reid, S.R. and Al-Hassani, S.T.S. Static and Dynamic Penetration of Steel Tubes by Hemispherically Nosed Punches, Int J Impact Eng, 9(2), pp. 165-190. 1990. Corbett, G.G., Reid, S.R. and Al-Hassani, S.T.S. Resistance of Steel-Concrete Sandwich Tubes to Penetration, Int J Impact Eng, Vol 9(2), pp. 191-230. 1990. Dai, X.X. and Liew, J.Y.R. Fatigue Performance of Lightweight Steel-Concrete-Steel Sandwich Systems, J Constr Steel Res, 66(2), pp. 256-276. 2010. Darwin, D. and Pecknold, D.A. Nonlinear Biaxial Stress-Strain Law for Concrete, J Eng Mech, ASCE, 103(2), pp. 229-241. 1977. DBJ/T 13-51-2010. Technical Specification for Concrete-Filled Steel Tubular Structures. Fuzhou (China): The Department of Housing and Urban-Rural Development of Fujian Province. 2010. Deng, Y., Norton, T.R. and Tuan, C.Y. Numerical Analysis of Concrete-Filled Circular Steel Tubes, Proc ICE Struct Build, 166(SB1), pp. 3-16. 2013. Deng, Y. and Tuan, C.Y. Design of Concrete-Filled Circular Steel Tubes under Lateral Impact, ACI Struct J, 110(4), pp. 691-701. 2013. Deng, Y., Tuan, C.Y. and Xiao, Y. Flexural Behavior of Concrete-Filled Circular Steel Tubes under High-Strain Rate Impact Loading, J Struct Eng, 138(3), pp. 449-56. 2012. Det Norske Veritas. Risk assessment of pipeline protection. Recommended, practice, DNVRP-F107. 2010. Det Norske Veritas. Design against accidental loads. Recommended, practice, DNV-RP-C204. 2010. Det Norske Veritas. Submarine Pipeline systems. Recommended, practice, DNV-OS-F101. 2010. Elchalakani, M., Zhao, X.L. and Grzebieta, R.H. Concrete-Filled Circular Steel Tubes Subjected to Pure Bending, J Constr Steel Res, 57(11), pp. 1141-1168. 2001. 206 References Eurocode 2. Design of Concrete Structures, Part 1.1: General Rules and Rules for Buildings. ENV 1994-1-1. London: British Standards Institution. 2004. Eurocode 4. Design of Composite Steel and Concrete Structures, Part 1.1: General Rules and Rules for Buildings. ENV 1994-1-1. London: British Standards Institution. 2004. Evans, G.R., Jones, B.C., McMillan, A.J. and Darby M.I. A New Numerical Method for the Calculation of Impact Forces, J Phys D Appl Phys, 24(6), pp. 854-858. 1991. Famiyesin, O.O.R., Oliver, K.D. and Rodger, A.A. Semi-Empirical Equations for Pipeline Design by the Finite Element Method, Comput Struct, 80(16-17), pp. 1369-1382. 2002. Fan, Z., Shen, J. and Lu, G. Investigation of Lateral Crushing of Sandwich Tubes, Procedia Eng, 14, pp. 442-449. 2011. Fan, Z., Shen, J., Lu, G. and Ruan, D. Energy Absorption of Sandwich Tubes under Lateral Loading, Conf Proc Soc Exp Mech Ser, 1, pp. 321-328. 2013. Fan, Z., Shen, J., Lu, G. and Ruan, D. Dynamic Lateral Crushing of Empty and Sandwich Tubes, Int J Impact Eng, 53, pp. 3-16. 2013. Fernandez, R.P. and Pardo, M.L. Offshore Concrete Structures, Ocean Eng, 58(15), pp. 304316. 2013. Field, J.E., Walley, S.M., Proud, W.G., Goldrein, H.T. and Siviour, C.R. Review of Experimental Techniques for High Rate Deformation and Shock Studies, Int J Impact Eng, 30(7), pp. 725-775. 2004. Firouzsalari, S.E. and Showkati, H. Thorough Investigation of Continuously Supported Pipelines under Combined Pre-Compression and Denting Loads, Int J Pressure Vessels Pip, 104, pp. 83-95. 2013. Firouzsalari, S.E. and Showkati, H. Behavior of Pre-Compressed Tubes Subjected to Local Loads, Ocean Eng, 65(1), pp. 19-31. 2013. Firouzsalari, S.E. and Showkati, H. Investigation of Free-Spanned Pipeline Behavior Due to Axial Forces and Local Loads, J Constr Steel Res, 86, pp. 128-139. 2013. Foundoukos, N. and Chapman, J.C. Finite Element Analysis of Steel-Concrete-Steel Sandwich Beams, J Constr Steel Res, 64(9), pp. 947-961. 2008. Gresnigt, A.M., Karamanos, S.A. and Andreadakis, K.P. Lateral Loading of Internally Pressurized Steel Pipes, Trans ASME J Press Vessel Technol, 129(4), pp. 630-638. 2007. Goldsmith, W. Impact, The Theory and Physical Behavior of Colliding Solids. London: Edward Arnold Publishers. 1960. 207 References Gu, D.B. Accident Research on Steel Tube-Confined Concrete under Lateral Impact (in Chinese). M. Sc. thesis, Taiyuan University of technology. 2005. Guden, M. and Kavi, H. Quasi-Static Axial Compression Behavior of Constraint Hexagonal and Square-Packed Empty and Aluminum Foam-Filled Aluminum Multi-Tubes, Thin-Walled Struct, 44(7), pp. 739-750. 2006. Guo, L. and Yu, J. Dynamic Bending Response of Double Cylindrical Tubes Filled with Aluminum Foam, Int j Impact Eng, 38(2-3), pp. 85-94. 2011. Hallquist, J.O. LS-DYNA Keyword User Manual-Nonlinear Dynamic Analysis of Structures. Livermore Software Technology Corporation, Livermore, California. 2006. Han, L.H. Flexural Behavior of Concrete-Filled Steel Tubes, J Constr Steel Res, 60(2), pp. 313-337. 2004. Han, L.H., Hou, C.C., Zhao, X.L. and Rasmussen, K.J.R. Behavior of High-Strength Concrete Filled Steel Tubes under Transverse Impact Loading, J Constr Steel Res, 92, pp. 25-39. 2014. Han, L.H., Huang, H., Tao, Z. and Zhao, X.L. Concrete-Filled Double Skin Steel Tubular (CFDST) Beam-Columns Subjected to Cyclic Bending, Eng Struct, 28(12), pp. 1698-1714. 2006. Han, L.H., Huang, H. and Zhao, X.L. Analytical Behavior of Concrete-Filled Double Skin Steel Tubular (CFDST) Beam Columns under Cyclic Loading, Thin-Walled Struct, 47(6-7), pp. 668-680. 2009. Han, L.H., Li, Y.J. and Liao, F.Y. Concrete-Filled Double Skin Steel Tubular (CFDST) Columns Subjected to Long-Term Sustained Loading, Thin-Walled Struct, 49(12), pp. 15341543. 2011. Han, L.H., Lu, H., Yao, G.H. and Liao, F.Y. Further Study on the Flexural Behaviour of Concrete-Filled Steel Tubes, J Constr Steel Res, 62(6), pp. 554-565. 2006. Han, L.H., Yao, G.H. and Zhao, X.L. Tests and Calculations for Hollow Structural Steel (HSS) Stub Columns Filled with Self-Consolidating Concrete (SCC), J Constr Steel Res, 61(9), pp. 1241-1269. 2005. Han, T.H., Stallings, J.M. and Kang, Y.J. Nonlinear Concrete Model for Double-Skinned Composite Tubular Columns, Constr Build Mater, 24(12), pp. 2542-2553. 2010. Han, T.H., Won, D.H., Kim, S. and Kang, Y.J. Performance of A Double-Skinned Composite Tubular Column under Lateral Loading: Analysis, Mag Concr Res, 65(2), pp. 121-135. 2013. Harding, J.E. and Onoufriou, A. Behavior of Ring-Stiffened Cylindrical Members Damaged by Local Denting, J Constr Steel Res, 33(3), pp. 237-257. 1995. 208 References Hassanein, M.F., Kharoob, O.F. and Liang, Q.Q. Circular Concrete-Filled Double Skin Tubular Short Columns with External Stainless Steel Tubes under Axial Compression, ThinWalled Struct, 73, pp. 252-263. 2013. Hou, C., Han, L.H. and Zhao, X.L. Concrete-Filled Circular Steel Tubes Subjected to Local Bearing Force: Experiments, J Constr Steel Res, 83, pp. 90-104. 2013. Hou, C., Han, L.H. and Zhao, X.L. Concrete-Filled Circular Steel Tubes Subjected to Local Bearing Force: Finite Element Analysis, Thin-Walled Struct, 77, pp. 109-119. 2014. Hu, H.T. and Su, F.C. Nonlinear Analysis of Short Concrete-Filled Double Skin Tube Columns Subjected to Axial Compressive Forces, Mar Struct, 24(4), pp. 319-337. 2011. Huang, H., Han, L.H., Tao, Z. and Zhao, X.L. Analytical Behavior of Concrete-Filled Double Skin Steel Tubular (CFDST) Stub Columns, J Constr Steel Res, 66(4), pp. 542-555. 2010. Hyde, T.H., Luo, R. and Becker, A.A. Elastic-Plastic Response of Unpressurised Pipes Subjected to Axially-Long Radial Indentation, Int J Mech Sci, 47(12), pp. 1949-1971. 2005. Hyde, T.H., Luo, R. and Becker, A.A. Prediction of Force-Deflection Behavior of Pressurized Pipes Subjected to Axially Long Radial Indentation, Int J Pressure Vessels Pip, 82(8), pp. 625637. 2005. Hyde, T.H., Luo, R. and Becker, A.A. Elastic-Plastic Analysis of Offset Indentations on Unpressurised Pipes, Int J Solids Struct, 44(2), pp. 399-418. 2007. Hyde, T.H., Luo, R. and Becker, A.A. Force-Deflection Analysis of Offset Indentations on Pressurized Pipes, Int J Pressure Vessels Pip, 84(6), pp. 368-377. 2007. Ishikawa, N. and Hoshikawa, T. Impact Absorption Energy of Steel Beam, Nucl Eng Des, 150(2-3), pp. 303-308. 1994. Jing, L., Wang, Z. and Zhao, L. Response of Metallic Cylindrical Sandwich Shells Subjected to Projectile Impact-Experimental Investigations, Compos Struct, 107(1), pp. 36-47. 2014. Jones, N. Structural impact. Cambridge: Cambridge University Press. 1989. Jones, N. and Birch, R.S. Influence of Internal Pressure on the Impact Behavior of Steel Pipelines, J Pressure Vessel Technol Trans ASME, 118(4), pp. 464-471. 1996. Jones, N. and Birch, R.S. Low-Velocity Impact of Pressurized Pipelines, Int J Impact Eng, 37(2), pp. 207-219. 2010. Jones, N., Brich, S.E., Birch, R.S., Zhu, L. and Brown, M. An Experimental Study on the Lateral Impact of Fully Clamped Mild Steel Pipes, Proc Instn Mech Eng E J Process Mech Eng, 206(E2), pp. 111-127. 1992. 209 References Jones, N. and Shen, W.Q. A Theoretical Study of the Lateral Impact of Fully Clamped Pipelines, Proc Instn Mech Eng E J Process Mech Eng, 206(E2), pp. 129-146. 1992. JTG D60. General Code for Design of Highway Bridges and Culverts (in Chinese). 2004. Karamanos, S.A. and Andreadakis, K.P. Denting of Internally Pressurized Tubes under Lateral Loads, Int J Mech Sci, 48(10), pp. 1080-1094. 2006. Karroum, C.G., Reid, S.R. and Li, S. Indentation of Ring-Stiffened cylinders by wedge-shaped indenters-Part 1: An Experimental and Finite Element Investigation, Int J Mech Sci, 49(1), pp. 13-38. 2007. Karroum, C.G., Reid, S.R. and Li, S. Indentation of Ring-Stiffened cylinders by wedge-shaped indenters-Part 2: Scale model tests, Int J Mech Sci, 49(1), pp. 39-53. 2007. Khedmati, M.R. and Nazari, M. A Numerical Investigation into Strength and Deformation Characteristics of Preloaded Tubular Members under Lateral Impact Loads, Mar Struct, 25(1), pp. 33-57. 2012. Kristoffersen, M., Borvik, T., Westermann, I., Langseth, M. and Hopperstad O.S. Impact Against X65 Pipes – An Experimental Investigation, Int J Solids Struct, 50(20-21), pp. 34303445. 2013. Kuranovas, A. and Kvedaras, A.K. Behaviour of Hollow Concrete-Filled Steel Tubular Composite Elements, J Civ Eng Manage, 13(2), pp. 131-141. 2007. Kuranovas, A. and Kvedaras, A.K. Centrifugally Manufactured Hollow Concrete-Filled Steel Tubular Columns, J Civ Eng Manage, 13(4), pp. 297-306. 2007. Lee, E.H. The Impact of A Mass Striking A Beam, J Appl Mech, 7, pp. 129-138. 1940. Lee, S.C. Finite Element Modeling of Hybrid-Fiber ECC Targets Subjected to Impact and Blast. Ph.D Thesis, National University of Singapore. 2006. Li, J., Wang, S. and Johnson, W. Pipe/Duct System Design for Tornado Missile Impact Loads, Nucl Eng Des, 269(1), pp. 217-221. 2014. Li, W.L. Experimental Study and Numerical Simulation Analysis of the Concrete Filled in Steel Tube Specimens under Lateral Impact (in Chinese). M. Sc. thesis, Taiyuan University of technology. 2007. Li, W., Han, L.H., and Zhao, X.L. Axial Strength of Concrete-Filled Double Skin Steel Tubular (CFDST) Columns with Preload on Steel Tubes, Thin-Walled Struct, 56, pp. 9-20. 2012. Li, W., Ren, Q.X., Han, L.H. and Zhao, X.L. Behaviour of Tapered Concrete-Filled Double Skin Steel Tubular (CFDST) Stub Columns, Thin-Walled Struct, 57, pp. 37-48. 2012. 210 References Li, Z., Zheng, Z., Yu, J. and Guo, L. Crashworthiness of Foam-Filled Thin-Walled Circular Tubes under Dynamic Bending, Mater Des, 52, 1058-1064. 2013. Liew, J.Y.R. and Sohel, K.M.A. Lightweight Steel-Concrete-Steel Sandwich System with JHook Connectors, Eng Struct, 31(5), pp. 1166-1178. 2009. Liew, J.Y.R. and Sohel, K.M.A. Structural Performance of Steel-Concrete-Steel Sandwich Composite Structures, Adv Struct Eng, 13(3), pp. 453-470. 2010. Liew, J.Y.R., Sohel, K.M.A. and Koh, C.G. Impact Test on Steel-Concrete-Steel Sandwich Beams with Lightweight Concrete Core, Eng Struct, 31(9), pp. 2045-2059. 2009. Liew, J.Y.R. and Wang T.Y. Novel Steel-Concrete-Steel Sandwich Composite Plates Subject to Impact and Blast Load, Adv Struct Eng, 14(4), pp. 673-687. 2011. Liew, J.Y.R. and Xiong, D.X. Experimental Investigation on the Flexural Behaviour of Concrete Filled Steel Tubes with High Strength Material. In Proc. 10th International Conference on Advances in Steel Concrete Composite and Hybrid Structures (ASCCS), July 2012, Singapore, pp. 346-353. Liu, J.H. and Francis, A. Theoretical Analysis of Local Indentation on Pressured Pipes, Int J Pressure Vessels Pip, 81(12), pp. 931-939. 2004. Lu, G. A Study of the Crushing of Tubes by Two Indenters, Int J Mech Sci, 35(3-4), pp. 267278. 1993. Lu, G.Y., Lei, J.P., Han, Z.J., Liu, Z.F. and Zhang, S.Y. Denting and Failure of Liquid-Filled Tubes under Lateral Impact, Acta Mech Solida Sin, 25(6), pp. 609-615. 2012. Lu, G.Y., Zhang, S.Y., Lei, J.P. and Yang, J.L. Dynamic Responses and Damages of WaterFilled Pre-Presssurized Metal Tube Impacted by Mass, Int J Impact Eng, 34(10), pp. 15941601. 2007. Lu, H., Han, L.H. and Zhao, X.L. Analytical Behavior of Circular Concrete-Filled ThinWalled Steel Tubes Subjected to Bending, Thin-Walled Struct, 47(2), pp. 346-358. 2009. Macdonald, K.A., Cosham, A., Alexander, C.R. and Hopkins, P. Assessing Mechanical Damage in Offshore Pipelines – Two Case Studies. Eng Fail Anal, 14(8), pp. 1667-1679. 2007. Malvar, L.J., Crawford, J.E., Wesevich, J.W. and Simons, D. A Plasticity Concrete Material Model for DYNA3D, Int J Impact Eng, 19(9-10), pp. 847-873. 1997. Malvar, L.J. and Ross C.A. Review of Strain Rate Effects for Concrete in Tension, ACI Mater J, 95(6), pp. 735-739. 1998. Mamalis, A.G., Manolakos, D.E., Ioannidis, M.B. and Kostazos, P.K. Bending of Cylindrical Steel Tubes: Numerical Modeling, Int J Crashworthiness, 11(1), pp. 37-47. 2010. 211 References Masaru, S., Fumihito, T., Toshiyuki, I., Atsushi, H. and hirotaka, Kawano. Experimental Study on Ultimate Strength of Concrete Filled Double Tubular Steel with Shear Connector, Int J Steel Struct, 13(1), pp. 49-54. 2013. McKinley, B. and Boswell, L.F. Behaviour of Double Skin Composite Construction, J Constr Steel Res, 58(10), pp. 1347-1359. 2002. Montague, P. Simple Composite Construction for Cylindrical Shells Subjected to External Pressure, J Mech Eng Sci, 17(2), pp. 105-113. 1975. Montague, P. The Experimental Behavior of Double Skinned, Composite, Circular Cylindrical Shells under External Pressure, J Mech Eng Sci, 20(1), pp. 21-34. 1978. Montague, P. The Failure of Double Skinned, Composite, Circular Cylindrical Shells under External Pressure, J Mech Eng Sci, 20(1), pp. 35-48. 1978. Montague, P. The Theoretical Behavior of Steel Concrete Circular Cylindrical Shells Subjected to External Pressure, Proc Inst Civ Eng, 67(2), pp. 483-499. 1979. Montague, P. Composite Shell Resist Pressure, CME Chart Mech Eng, 32(3), pp. 40-42. 1985. Moon, J., Roeder, C.W., Lehman, D.E. and Lee, H.E. Analytical Modeling of Bending of Circular Concrete-Filled Steel Tubes, Eng Struct, 42, pp. 349-361. 2012. Ng, C.S. and Shen, W.Q. Effect of Lateral Impact Loads on Failure of Pressurized Pipelines Supported by Foundation, Proc Instn Mech Eng E J Process Mech Eng, 220(E4), pp. 193-206. 2006. Ong, L.S. and Lu, G. Collapse of Tubular Beams Loaded by A Wedge-Shaped Indenter, Exp Mech, 36(4), pp. 374-378. 1996. Osage, D.A., Pressure Vessel Research Council (Welding Research Council [U.S.]), Krishnaswamy, P., Stephens, D.R., Scott, P., Janelle, J., Mohan, R. and Wilkowski, G.M. Technologies for the Evaluation of Non-Crack-Like Flaws in Pressurized Components: Erosion/Corrosion, Pitting, Blisters, Shell Out-Of-Roundness, Weld Misaglignment, Bulges and Dents. Welding Research Council. 2001. Ottosen, N.S. and Ristinmaa, M. The Mechanics of Constitutive Modeling. Amsterdam, London: Elsevier. 2005. Packer, J.A., Wardenier, J., Zhao, X.L., der Vegte, G.J. Van., Kurobane, Y. Design Guide for Rectangular Hollow Section (RHS) Joints under Predominantly Static Loading. CIDECT Series “Construction with Hollow Steel Section: 2nd ed., 3. CIDECT. 2009. Palmer, A., Neilson, A. and Sivadasan, S. Pipe Perforation by Medium-Velocity Impact, Int J Impact Eng, 32(7), pp. 1145-1157. 2006. 212 References Palmer, A., Touhey, M., Holder, S., Anderson, M. and Booth, S. Full-Scale Impact Tests on Pipelines, Int J Impact Eng, 32(8), pp. 1267-1283. 2006. Poonaya, S., Teeboonma, U. and Thinvongpituk, C. Plastic Collapse Analysis of Thin-Walled Circular Tubes Subjected to Bending, Thin-Walled Struct, 47(6-7), 637-645. 2009. Pryer, J.W. and Bowerman, H.G. The Development and Use of British Steel Bi-Steel, J Constr Steel Res, 46(1-3), pp. 15. 1998. Qian, X., Jitpairod, K., Marshall, P.W., Swaddiwudhipong, S., Ou, Z., Zhang, Y. and Pradana, M.R. Fatigue and Residual Strength of Concrete-Filled Tubular X-Joints with Full Capacity Welds, J Constr Steel Res, in press. 2014. Qin, Q.H. and Wang, T.J. Low-Velocity Impact Response of Fully Clamped Metal Foam Core Sandwich Beam Incorporating Local Denting Effect, Compos Struct, 96, pp. 345-356. 2013. Qu, H.Y., Li, G.Q., Chen, S.W. Sun, J.Y. and Sozen, M.A. Analysis of Circular ConcreteFilled Steel Tube Specimen under Lateral Impact, Adv Struct Eng, 14(5), pp. 941-951. 2011. Ramberg, W. and Osgood, W.R. Description of Stress-Strain Curves by Three Parameters. Technical Note No. 902. Washington (DC): National Advisory Committee for Aeronautics. 1943. Reddy, T.Y. and Wall, R.J. Axial Compression of Foam-Filled Thin-Walled Circular Tubes, Int J Impact Eng, 7(2), pp. 151-166. 1988. Reid, S.R. Metal Tubes as Impact Energy Absorbers. Metal Forming and Impact Mechanics, William Johnson Commemorative Volume. Pergamon, Oxford. 1985. Remnnikov, A.M. and Kong, S.Y. Numerical Simulation and Validation of Impact Response of Axially-Restrained Steel-Concrete-Steel Sandwich Panels, Compos Struct, 94(12), pp. 3546-3555. 2012. Remnnikov, A.M., Kong, S.Y. and Uy, B. The Response of Foam- and Concrete-Filled Square Steel Tubes under Low Velocity Impact Loading, J Perform Constr Facil, 25(5), pp. 373-381. 2011. Remnnikov, A.M., Kong, S.Y. and Uy, B. The Response of Axially Restrained NonComposite Steel-Concrete-Steel Sandwich Panels Due to Large Impact Loading, Eng Struct, 49, pp. 806-818. 2013. Richardson, M.O.W. and Wishear, M.J. Review of Low-Velocity Impact Properties of Composite Materials, Compos A Appl Sci Manuf, 27A(12), pp. 1123-1131. 1996. Rosenfeld, M.J. Here Are Factors that Govern Evaluation of Mechanical Damage to Pipelines, Oil Gas J, 100(37), pp. 64-69. 2002. 213 References Shakir-Khalil, H. Composite Columns of Double-Skinned Shells, J Constr Steel Res, 19(2), pp. 133-152. 1991. Shen, J., Lu, G., Zhao, L. and Zhang, Q. Short Sandwich Tubes Subjected to Internal Explosive Loading, Eng Struct, 56, pp. 56-65. 2013. Shen, W.Q. and Shu, D.W. A Theoretical Analysis on the Failure of Unpressurized and Pressurized Pipelines, Proc Instn Mech Eng E J Process Mech Eng, 216(3), pp. 151-164. 2002. Sohel, K.M.A. Impact Behaviour of Steel-Composite Sandwich Beams. M. Eng. Thesis, National University of Singapore. 2003. Sohel, K.M.A. Impact Performance of Steel-Concrete-Steel Sandwich Structures. Ph.D. Thesis, National University of Singapore, Singapore. 2008. Sohel, K.M.A. and Liew, J.Y.R. Steel-Concrete-Steel Sandwich Slabs with Lightweight CoreStatic Performance, Eng Struct, 33(3), pp. 981-992. 2011. Sohel, K.M.A., Liew, J.Y.R., Yan, J.B., Zhang, M.H. and Chia, K.S. Behavior of SteelConcrete-Steel Sandwich Structures with Lightweight Cement Composite and Novel Shear Connectors, Compos Struct, 94(12), pp. 3500-3509. 2012. Solomon, S.K., Smith, D.W. and Cusens, A.R. Flexural Tests of Steel-Concrete-Steel Sandwiches, Mag Concr Res, 28(94), pp. 13-20. 1976. Song, H.W. and Wang, H.T. Statistical Evaluation for Impact Resistance of Steel Fiber Reinforced Lightweight Aggregate Concrete, Adv Mater Res, 250-253, pp. 609-613. 2011. SS EN 12620. Specification for aggregates for concrete. CEN; 2008. Stronge, W.J. Impact on Metal Tubes: Indentation and Perforation. In: Jones, N. and Wierzbicki, T. editors. Structural Crashworthiness and Failure. London and New York: Elsevier Applied Science, pp. 165-188. 1993. Swaddiwudhipong, S. and Seow, P.E.C. Modelling of Steel Fiber-Reinforced Concrete under Multi-Axial Loads, Cem Concr Res, 36(7), pp. 1354-1361. 2006. Thomas, S.G., Reid, S.R. and Johnson, W. Large Deformations of Thin-Walled Circular Tubes under Transverse Loading-I An Experimental Survey of the Bending of Simply Supported Tubes under A Central Load, Int J Mech Sci, 18(6), pp. 325-333. 1976. Toutanji, H., Xu, B., Gilbert, J. and Lavin, T. Properties of Poly(vinyl alcohol) Fiber Reinforced High-Performance Organic Aggregate Cementitious Material: Converting Brittle to Plastic, Constr Build Mater, 24(1), pp. 1-10. 2010. Travanca, J. and Hao, H. Numerical Analysis of Steel Tubular Member Response to Ship Bow Impacts, Int J Impact Eng, 64, pp. 101-121. 2014. 214 References Uenaka, K. Concrete Filled Double Skin Circular Tubular Beams With Large Diameter-toThickness Ratio under Shear, Thin-Walled Struct, 70, pp. 33-38. 2013. Uenaka, K. and Kitoh, H. Mechanical Behavior of Concrete Filled Double Skin Tubular Circular Deep Beams, Thin-Walled Struct, 49(2), pp. 256-263. 2011. Uenaka, K., Kitoh, H. and Sonoda, K. Concrete Filled Double Skin Circular Stub Columns under Compression, Thin-Walled Struct, 48(1), pp. 19-24. 2010. Wang, K.Z. Experimental Research on Concrete-Filled Steel Tubes under Lateral Impact Load (in Chinese). M. Sc. thesis, Taiyuan University of technology. 2005. Wang, R., Han, L.H. and Hou, C.C. Behaviour of Concrete Filled Steel Tubular (CFST) Members under Lateral Impact, J Constr Steel Res, 80, pp. 188-201. 2013. Wang, S. Experimental and Numerical Studies on Behavior of Plain and Fiber-Reinforced High-Strength Concrete Subjected to High Strain Rate Loadings. Ph.D. Thesis, National University of Singapore. 2011. Wang, H.T. and Wang, L.C. Experimental Study on Static and Dynamic Mechanical Properties of Steel Fiber Reinforced Lightweight Aggregate Concrete, Constr Build Mater, 38, pp. 1146-1151. 2013. Wastiels, J. Behaviour of Concrete under Multiaxial Stresses – A Review, Cem Concr Res, 9(1), pp. 35-44. 1979. Watson, A.R., Reid, S.R., Johnson, W. and Thomas, S.G. Large Deformations of Thin-Walled Circular Tubes under Transverse Loading-II Experimental Study of the Crushing of Circular Tubes by Centrally Applied Opposed Wedge-Shaped Indenters, J Mech Sci, 18(7-8), pp. 387397. 1976. Watson, A.R., Reid, S.R. and Johnson, W. Large Deformations of Thin-Walled Circular Tubes under Transverse Loading-III Further Experiments on the Bending of Simply Supported Tubes, J Mech Sci, 18(9-10), pp. 501-509. 1976. Wen, H.M. Large Plastic Deformation of Spherical Shells under Impact by Blunt-Ended Missiles, Int J Pressure Vessels Pip, 73(2), pp. 147-152. 1997. Wen, H.M. and Jones, N. Low Velocity Perforation of Punch-Impact-Loaded Metal Plates, J Pressure Vessel Technol Trans ASME, 118(2), pp. 181-187. 1996. Wen, H.M. and Reid, S.R. Deformation and Perforation of Cylindrical Shells Struck Normally by Blunt Projectiles, Int J Pressure Vessels Pip, 75(3), pp. 213-219. 1998. Wierzbicki, T. and Suh, M.S. Indentation of Tubes under Combined Loading, Int J Mech Sci, 30(3-4), pp. 229-248. 1988. 215 References Wright, H.D., Oduyemi, T.O.S. and Evans, H.R. The Experimental Behavior of Double Skin Composite Elements, J Constr Steel Res, 19(2), pp. 97-110. 1991. Xu, B., Toutanji, H.A. and Gilbert, J. Impact Resistance of Poly (Vinyl Alcohol) Fiber Reinforced High-Performance Organic Aggregate Cementitious Material, Cement Concr Res, 40(2), pp. 347-351. 2010. Yang, J.L., Lu, G.Y., Yu, T.X. and Reid, S.R. Experimental Study and Numerical Simulation of Pipe-On-Pipe Impact, Int J Impact Eng, 36(10-11), pp. 1259-1268. 2009. Yang, Y.F. and Han, L.H. Concrete-Filled Double-Skin Tubular Columns under Fire, Mag Concr Res, 60(3), pp. 211-222. 2008. Yang, Y.F., Han, L.H. and Sun, B.H. Experimental Behaviour of Partially Loaded Concrete Filled Double-Skin Steel Tube (CFDST) Sections, J Constr Steel Res, 71, pp. 63-73. 2012. Yang, Y.F., Hou, C., Wen, Z. and Han, L.H. Experimental Behaviour of Square CFST under Local Bearing Forces, Thin-Walled Struct, 74, pp. 166-183. 2014. Yousuf, M., Uy, B. and Tao, Z. Experimental Behavior of Pre-Compressive Concrete-Filled Steel Tubular (CFST) Columns under Lateral Impact Loading. In Proc. 10th International Conference on Advances in Steel Concrete Composite and Hybrid Structures (ASCCS), July 2012, Singapore, pp. 1099-1106. Yousuf, M., Uy, B., Tao, Z., Remennikov, A. and Liew, J.Y.R. Transverse Impact Resistance of Hollow and Concrete Filled Stainless Steel Columns, J Constr Steel Res, 82, pp. 177-189. 2013. Yu, M., Zha, X.X. and Wang, Y.C. Behaviour of Different Types of Columns under Vehicle Impact. In Proc. 3rd International Conference on Steel and Composite Structures, ICSCS07 Steel and Composite Structures, July 2007, Manchester, UK, pp. 879-885. Zeinoddini, M., Arabzadeh, H., Ezzati, M. and Parke, G.A.R. Response of Submarine Pipelines to Impacts from Dropped Objects: Bed Flexibility Effects, Int J Impact Eng, 62, pp. 129-141. 2013. Zeinoddini, M., Harding, J.E. and Parke, G.A.R. Effect of Impact Damage on the Capacity of Tubular Steel Members of Offshore Structures, Mar struct, 11(4-5), pp.141-157. 1998. Zeinoddini, M., Harding, J.E. and Parke, G.A.R. Dynamic Behavior of Axially Pre-Loaded Tubular Steel Members of Offshore Structures Subjected to Impact Damage, Ocean Eng, 26(10), pp. 963-978. 1999. Zeinoddini, M., Harding, J.E. and Parke, G.A.R. Contribution of Ring Resistance in the Behavior of Steel Tubes Subjected to a Lateral Impact, Int J Mech Sci, 42(12), pp. 2303-2320. 2000. 216 References Zeinoddini, M., Harding, J.E. and Parke, G.A.R. Axially Pre-Loaded Steel Tubes Subjected to Lateral Impacts: A Numerical Simulation, Int J Impact Eng, 35(11), pp.1267-1279. 2008. Zeinoddini, M., Parke, G.A.R. and Harding, J.E. Axially Pre-Loaded Steel Tubes Subjected to Lateral Impacts: An Experimental Study, Int J of Impact Eng, 27(6), pp. 669-690. 2002. Zeinoddini, M., Parke, G.A.R. and Harding, J.E. Interface Forces in Laterally Impacted Steel Tubes, Proc Soc Exp Mech, 48, pp. 265-280. 2008. Zhang, Y.F., Zhao, J.H. and Cai, C.S. Seismic Behavior of Ring Beam Joints between Concrete-Filled Twin Steel Tubes Columns and Reinforced Concrete Beams, Engineering Structures, 39, pp. 1-10. 2012. Zhao, X.L. and Han, L.H. Double Skin Composite Construction. Progress in Structural Engineering and Materials, 8(3), pp. 93-102. 2006. Zhao, X.L. and Leung, A. Maximum Bending Moment Capacity of CFDST Beams with Inner Tubes Shifted Towards the Tensile Side. In Proc. 10th Pacific Structural Steel Conference (PSSC), October 2013, Singapore, pp. 67-72. Zhao, X.L., Tong, L.W. and Wang, X.Y. CFDST Stub Columns Subjected to Large Deformation Axial Loading, Eng Struct, 32(3), pp. 692-703. 2010. Zheng, J., Palmer, A. and Brunning, P. Overtrawlability and Mechanical Damage of Pipe-InPipe, J Appl Mech Trans ASME, 81(3), pp. 031006-1-11. 2014. 217 List of publications LIST OF PUBLICATIONS Wang, Y., Qian, X., Liew, J. Y. R., & Zhang, M-H. Experimental Behavior of Cement Filled Pipe-In-Pipe Composite Structures under Transverse Impact. Int J Impact Eng, 72, pp. 1-16. 2014. Wang, Y., Qian, X., Liew, J. Y. R., & Zhang, M-H.Impact of Cement Composite Filled Steel Tubes: An Experimental, Numerical and Theoretical Treatise.Thin-Walled Struct, 87, pp. 7688. 2015. Wang, Y., Qian, X., Liew, J. Y. R., & Zhang, M-H. Concrete-Filled Pipe-In-Pipe Composite Structure under Transverse Impact Loading. In Proc. 10th International Conference on Advances in Steel Concrete Composite and Hybrid Structures, July 2012, Singapore, pp. 11071114. Wang, Y., Qian, X., Liew, J. Y. R., & Zhang, M-H. Experimental Behavior of Cement Composite Filled Pipe-In-Pipe Sandwich Structures under Transverse Impact Loading. In Proc. 10th Pacific Structural Steel Conference, October 2013, Singapore, pp. 630-635. Wang, Y., Qian, X., Liew, J. Y. R., & Zhang, M-H. Experimental Behavior of Cement Filled Pipe-In-Pipe Composite Structures under Lateral Indentation. In Proc. 26th KKHTCNN Symposium on Civil Engineering, November 2013, Singapore. 218 [...]... generator model in the pipe- in -pipe composite structure ti Thickness of the inner pipe in the pipe- in -pipe composite structure to Thickness of the outer pipe in the pipe- in -pipe structure or thickness of the hollow steel pipe or thickness of the steel pipe in the cement composite filled pipe structure tring Equivalent thickness for the ring model in the pipe- in -pipe composite structure t1 Time instant when... Maximum impact force Po Indentation resistance of the outer pipe Pp Peak load of the tubular joint (Lu et al., 1994) Ps Serviceability strength of the tubular joint (Lu et al., 1994) Pu Ultimate strength R Radius of the pipe Rc External radius of the infilled cement composite cylinder Rci Failure stress of the cement composite in ith direction Ri External radius of the inner pipe in the pipe- in -pipe composite. .. radius of the outer pipe in the pipe- in -pipe structure or external radius of the hollow steel pipe or external radius of the steel pipe in the cement composite filled pipe structure R1 Radius of the bottom arc in a deformed ring R2 Radius of the upper arc in a deformed ring S Continuous deformation field SB Local effects factor defined in Eq (2.10) S BS Coefficient defined in Eq (2.30) Ts Tensile force in. .. steel pipes C3 , C 4 , C5 Coefficients in the recommended P-δ relationship for simply supported hollow steel pipes D Diameter of the pipe Di External diameter of the inner pipe in the pipe- in -pipe composite structure Dmax Maximum diameter of the pipe Dmin Minimum diameter of the pipe Do External diameter of the outer pipe in the pipe- in -pipe structure or external diameter of the hollow steel pipe or... predict the impact response of ULCC -filled pipe- in -pipe structures and to provide design implications on this composite pipe To achieve this target, the specific objectives are: (1) To investigate experimentally the transverse impact performance of the three types of pipe structures, i.e., the hollow pipe structures, the ULCC -filled pipe structures and the ULCC -filled pipe- in -pipe composite structures. .. develop finite element (FE) models to simulate the impact process and to have a deep understanding on the impact behavior of the pipe- in -pipe composite structures (3) To examine the load-indentation (P-δ) response for the pipe- in -pipe composite structures based on a combined experimental and numerical investigation (4) To develop theoretical methods to estimate the impact response of the pipe- in -pipe composite. .. stiffness of SCS composite beams (Liew et al., 2009) Kp Plastic contact stiffness of SCS composite beams (Liew et al., 2009) xviii List of symbols L Length of the pipe Lf Crushing failure length of the cement composite in the x-z plane Lo Clear span length of the pipe Lt Total length of the cement composite under the indenter in the x-z plane Lxz Length of the load-resistance area of the cement composite in. .. impact response for the pipe- in -pipe composite structures 1.3 Significance and Contributions This study will contribute to the existing literatures and hopefully lead to the recommendation of design guidelines for the practical use of the ULCC -filled pipe- in -pipe composite structure in pipeline applications against transverse impacts This study will extend the understanding of the impact behavior of. .. or the cement composite g Gravitational acceleration k Coefficient defined in Eqs (2.14) to (2.16) kd Internal scalar multiplier in MAT_72R3 in LS-DYNA m Coefficient defined in BS 5400-part 5 (2005) md Mass of the drop weight mo Coefficient defined in CIDECT (1995) mp Mass of the pipe n Strain-hardening exponent p Mean pressure of the cement composite in MAT_72R3 in LS-DYNA pi Internal pressure of the... the steel pipe (Gresnigt et al., 2007) r Radius of the semi-cylindrical indenter head xxii List of symbols  rf Strain rate enhancement factor in MAT_72R3 in LS-DYNA si Deviatoric stress tensor s1 Length of the bottom arc in a deformed ring s2 Length of the upper arc in a deformed ring s3 Half-length of the flat segment in a deformed ring t Thickness of the pipe tc Thickness of the cement composite . IMPACT PERFORMANCE OF CEMENT COMPOSITE FILLED PIPE- IN -PIPE STRUCTURES WANG YU NATIONAL UNIVERSITY OF SINGAPORE 2014 IMPACT PERFORMANCE OF CEMENT COMPOSITE. types of pipe specimens, including hollow pipe specimens, ULCC -filled pipe specimens and ULCC -filled pipe- in -pipe specimens. Besides the experimental investigation, this study simulates the impact. the pipe specimens by using the nonlinear finite element (FE) software LS-DYNA and conducts an FE parametric study to extend the understanding of the impact performance for pipe- in -pipe composite