PWO PWO-1 ELECTRICAL & POWER CONTROL C D E F G H I J K L B SECTION PWO A O P N CONTENTS POWER OUTLET WIRING DIAGRAM 2 POWER SOCKET 2 Wiring Diagram 2 PRECAUTION 5 PRECAUTIONS 5 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER" 5 PREPARATION 6 PREPARATION 6 Special Service Tool 6 REMOVAL AND INSTALLATION 7 POWER SOCKET 7 FRONT OR CONSOLE POWER SOCKET 7 Revision: May 2014 2014 Frontier PWO-2 < WIRING DIAGRAM > POWER SOCKET WIRING DIAGRAM POWER SOCKET Wiring Diagram INFOID:0000000009480401 ABMWA2330GB Revision: May 2014 2014 Frontier PWO POWER SOCKET PWO-3 < WIRING DIAGRAM > C D E F G H I J K L B A O P N ABMIA5515GB Revision: May 2014 2014 Frontier PWO-4 < WIRING DIAGRAM > POWER SOCKET ABMIA5516GB Revision: May 2014 2014 Frontier PWO PRECAUTIONS PWO-5 < PRECAUTION > C D E F G H I J K L B A O P N PRECAUTION PRECAUTIONS Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000010138397 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the SR and SB section of this Service Man- ual. WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SR section. • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har- ness connectors. PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni- tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury. • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery and wait at least three minutes before performing any service. Revision: May 2014 2014 Frontier PWO-6 < PREPARATION > PREPARATION PREPARATION PREPARATION Special Service Tool INFOID:0000000009480403 The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description — (J-42059) Power socket removal tool Removing power sockets AWMIA1148GB Revision: May 2014 2014 Frontier PWO POWER SOCKET PWO-7 < REMOVAL AND INSTALLATION > C D E F G H I J K L B A O P N REMOVAL AND INSTALLATION POWER SOCKET FRONT OR CONSOLE POWER SOCKET INFOID:0000000009480404 POWER SOCKET NOTE: If the tool does not fit because of the location of the power socket, further disassembly may be required. Refer to IP-15, "Removal and Installation" . Removal 1. Remove the fuse for the power socket. 2. Insert one end of the Tool (A) into one of the square holes inside the power socket. 3. Lift up the handle of the Tool until the other end of the Tool is inside the socket and snaps into the other square hole in the power socket. 4. Pull the power socket straight out with the Tool. 5. Disconnect the harness connector from the power socket. 6. Remove ring from power socket finisher while pressing pawls. Installation Installation is in the reverse order of removal. NOTE: Make sure to align the tab with the square notched area during installation. Tool number: — (J-42059) AWMIA1182GB WKIA1035E AWMIA1183GB Revision: May 2014 2014 Frontier