BS 336 1989 fire hose couplings and ancillary equipments

BS 336 1989 fire hose couplings and ancillary equipments BS 336 1989 fire hose couplings and ancillary equipments BS 336 1989 fire hose couplings and ancillary equipments BS 336 1989 fire hose couplings and ancillary equipments BS 336 1989 fire hose couplings and ancillary equipments BS 336 1989 fire hose couplings and ancillary equipments BS 336 1989 fire hose couplings and ancillary equipments

[...]... the threads BS 2779 (metric dimensions) BS 2870 Specification for rolled copper and copper alloys; sheet strip and foil Specification for copper and copper alloys Tubes BS 287 1 Part 1 Copper tubes for water, gas and sanitation BS 2872 Specification for copper and copper alloys Forging stock and forgings BS 2873 Specification for copper and copper alloys Wire BS 2874 Specification for copper and copper... alloy rods and sections (other than forging stock) BS 3019 TIG welding Part 1 Specification for TIG welding of aluminium, magnesium and their alloys BS 3102 Specification for brass eyelets and washers for general purposes Specification for rubber and plastics suction hoses and hose assemblies for fire- fighting purposes BS 3165 BS 3571 MIG welding Part 1 Specification for MIG welding of aluminium and aluminium... refinery shapes BS 6323 Specification for seamless and welded steel tubes for automobile, mechanical and general engineering purposes Part 1 General requirements Specification for non-percolating layflat delivery hoses and hose assemblies for fire fighting purposes BS 6391 Specification for malleable cast iron BS 6681 BS MA 18 ' Specification for salt water piping systems in ships BS MA 60 Summary and application... application of copper and copper alloy tubes for ships' pipework systems DD 139 Specification for zinc-aluminium alloy ingots and castings BS 3734 Specification for dimensional tolerances of solid moulded and extruded rubber products ' BS 336 : 1989 This British Standard, having been prepared under the direction of the Fire Standards Committee, was published under the authority of the Board of BSI and comes into... (grade 270) to BS 1154 or chloroprene rubber (C70) to BS 2752 and shall have the dimensions given in figure 15(a) BS 336 : 1989 Section two Connector ( s e e figure 6 and clause 8.1 1 Head I Licensed copy:RMJM, 30/08/2005, Uncontrolled Copy, © BSI Instant a ne ou s coupling 'Bolt or screw jointed] incorporating gland to permit swivelling 7 Standpipe shaft J End to suit method o f assembiy to standpipe shaft... suction strainer 22 I BS 336 : 1989 Section two 19 Suction hose coupling wrench 18.2 Basket strainers 18.2.1 General Basket strainers shall be in accordance with figure 18 and table 7 including method of connection 19.1 Form and length A suction hose coupling wrench shall have a fixed jaw, with an open yoke and a slotted pivoted jaw adjustable to fit 75 mm, 100 mm and 140 mm suction hose couplings (see clause... all BSI publications i s in the BSI Catalogue, supplemented each month by BSI News which is available to subscribing members of BSI and gives details of new publications, revisions, amendments and withdrawn standards Any person who, when making use of a British Standard, encounters an inaccuracy or ambiguity, is requested to notify BSI without delay in order that the matter may be investigated and. .. Packaging code Section 17 Wicker and veneer baskets BS 1134 Method for the assassment of surface texture BS 1154 Specification for natural rubber compounds BS 1224 Specification for electroplated coatings of nickel and chromium BS 1400 Specification for copper alloy ingots and copper alloy and high conductivity copper castings BS 1470 Specification for wrought aluminium and aluminium alloys for general... aluminium alloys BS 4168 Hexagon socket screws and wrench keys - metric series BS 4219 Slotted set screws; metric series BS 4422 Glossary of terms associated with fire BS 5041 Fire hydrant systems equipment BS 51 63 Specification for predominantly key-operated cast iron gate valves for waterworks purposes BS 5599 Specification for hard anodic oxide coatings on aluminium for engineering purposes BS 6017 Specification... sheet and strip BS 1471 Specification for wrought aluminium and aluminium alloys for general engineering purposes - drawn tube BS 1473 Specification for wrought aluminium and aluminium alloys for general engineering purposes - rivet, bolt and screw stock BS 1474 Specification for wrought aluminium and aluminium alloys for general engineering purposes - bars, extruded round tubes and sections BS 1490 . delivery hose couplings, suction hose couplings, delivery hose connectors, dividing and collecting breechings, branchpipes, nozzles, standpipes, blank caps and plugs, suction collecting heads and. Delivery hose couplings - male details 4 Delivery hose couplings - tail details 5 Delivery hose couplings - expansion ring details 6 Delivery hose connector 7 Dividing and collecting. British Standards Institution Licensed copy:RMJM, 30/08/2005, Uncontrolled Copy, © BSI BS 336 : 1989 Foreword This British Standard has been prepared under the direction of the Fire Standards