1. Trang chủ
  2. » Kỹ Thuật - Công Nghệ

Metal Machining Episode 3 ppt

30 145 0

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

THÔNG TIN TÀI LIỆU

Thông tin cơ bản

Định dạng
Số trang 30
Dung lượng 234,6 KB

Nội dung

No better relationship has ever been found, for machining with plane-faced tools. The reason for this is easy to understand. Qualitatively, a curled chip may be regarded as shorter (more compressed) at its inner radius than at its outer radius. Only rarely are chips so tightly curled that (r/t) < 5; even then the variation in compression from the chip centre- line to its inner and outer radii is only ± 0.1, i.e. t/(2r). Average chip equivalent strains (equation 2.4(b)) are typically greater than 1. Thus, the modifications to flow associated with curvature are secondary relative to the magnitude of the flow itself. The sort of factors that could affect chip radius are variations of friction along the chip/tool contact length and the roundness of the cutting edge, and also the work hardening behaviour and variations of work hardening behaviour through the thickness of the chip (most chips are formed from surfaces which themselves have previously been strained by machining). 2.2.4 Shear plane angle prediction The previous section gives data that show that chip thickness, and hence shear plane angle, depends on tool rake angle, friction and work hardening; and it records how forces and tool stresses can be estimated if shear plane angle, rake angle and friction angle are known. In this section, early attempts, by Merchant (1945) and Lee and Shaffer (1951), to predict the shear plane angle are introduced. Both attempted to relate shear plane angle to rake angle and friction angle, and ignored any effects of work hardening. Merchant suggested that chip thickness may take up a value to minimize the energy of cutting. For a given cutting velocity, this is the same as minimizing the cutting force (equa- tion (2.5(b)) with respect to f. The well-known equation results: f = p/4 – (l < a)/2 (2.9) Lee and Shaffer proposed a simple slip line field to describe the flow (see Appendix 1 and Chapter 6 for slip line field theory). For force equilibrium of the free chip, it requires that the pressure on the primary shear plane is constant along the length of the shear plane and equal to k. If (p/k) = 1 and Dk = 0 are substituted in equation (2.7), Lee and Shaffer’s result is obtained: f = p/4 – (l < a)or(f < a) = p/4 – l (2.10) Neither equation (2.9) nor (2.10) is supported by experiment. Although they correctly show a reducing f with increasing l and reducing a, each predicts a universal relation between f, l and a and this is not found in practice. However, they stimulated much exper- imental work from which later improvements grew. It is common practice to test the results of experiments against the predictions of equa- tions (2.9) and (2.10) by plotting the results as a graph of f against (l – a). It is an obvi- ous choice for testing equation (2.9); and equation (2.9) was the first of these to be derived. As far as equation (2.10) is concerned, an equally valid choice would be to plot (f – a) against l. Different views of chip formation are formed, depending on which choice is taken. The first choice may be regarded as the machine-centred view: (l – a) is the angle between the resultant force on the tool and the direction of relative motion between the work and tool. The second choice gives a process-centred view: (f – a) is the complement of the angle between the shear plane and the tool rake face. Figures 2.13 and 2.14 present selected experimental results according to both views. The data in Figure 2.13 (from Shaw, 1984) were obtained by machining a free-cutting Chip formation mechanics 53 Childs Part 1 28:3:2000 2:36 pm Page 53 steel at a low cutting speed (0.025 m/min), with high speed steel tools with rake angles from 0˚ to 45˚. A range of cutting fluids were applied to create friction coefficients from 0.13 to 1.33. When the results are plotted as commonly practised (Figure 2.13(a)), data for each rake angle lie on a straight line, with a gradient close to 0.75, half way between the expectations of equations (2.9) and (2.10). When the process-centred view is taken (Figure 2.13(b)), an almost single relation is observed between the friction coefficient and (f – a). Figure 2.14 collects data at higher, more practical, cutting speeds for turning a range of ferrous, aluminium and copper alloys (Eggleston et al., 1959; Kobayashi and Thomsen, 1959). Both parts of the figure show each material to have its own characteristic behaviour. Both show that annealed steel machines with a lower shear plane angle than the same steel cold-rolled. Figure 2.14(b) marginally groups the data in a smaller area than does Figure 2.14(a). Certainly part b emphasizes the range of friction angles, common to all the mater- ials, from 25˚ to 40˚ (friction coefficient from 0.47 to 0.84). As this book is machining- process centred, the view of part b is preferred. Figure 2.15 gathers more data on this basis. Figure 2.15(a) shows that free-cutting steels 54 Chip formation fundamentals Fig. 2.13 φ – λ – α relationships for low speed turning of a free cutting steel with tools of different rake angle (0ºx, 16º+, 30ºo, 45º•), varying friction by selection of cutting fluid: (a) φ versus ( λ – α ) and (b) ( φ – α ) versus λ (after Shaw, 1984) Fig. 2.14 φ – λ – α relationships for normal production speed turning by high speed steel tools, with rake angles from 5º to 40º, of cold rolled (•) and annealed (o) free cutting steel, an aluminium alloy (+) and an α -brass (×): (a) φ versus ( λ – α ) and (b) ( φ – α ) versus λ (data from Eggleston et al. , 1959) Childs Part 1 28:3:2000 2:37 pm Page 54 generally have lower friction coefficients (from 0.36 to 0.70) than non-free-cutting steels (from 0.47 to 1.00) when turned with high speed steel or cemented carbide tools (Childs, 1980a). Figure 2.15(b) extends the data to the machining of difficult materials such as austenitic stainless and high manganese steels, nickel-chromium and titanium alloys, by carbide and ceramic tools. Friction angles remain in the same range as for other materials but larger differences between shear plane and rake angle are found. Care must be taken in interpreting this last observation. Not only are lower rake angles used for the difficult to machine materials (from +10˚ to –5˚ for the data in the figure), biasing the data to larger (f – a), but these materials also give serrated chips. The data in Figure 2.15(b) are aver- aged over the cycle of non-steady chip formation. 2.2.5 Specific energies and material stress levels in machining In the preceding sections, basic force and moment equilibrium considerations have been used, with experimental observations, to establish the mechanical conditions of continu- ous chip formation. With the exception of the Merchant and Lee and Shaffer laws, predic- tion of chip shape has not been attempted. Predictive mechanics is left to Chapters 6 and after. In this section, by way of a summary, some final generalizations are made, concern- ing the energy used to form chips, and the level of contact stresses on the tool face. The work done per unit machined volume, the specific work, in metal cutting is F c /(fd). The dimensionless specific work, may be defined as F c /(kfd). Equation (2.11) takes equa- tion (2.5b) and manipulates it to F c cos(l < a)1 —— = ———————— ≡ —— + tan(f + l < a) (2.11) kfd sin f cos(f + l < a) tan f From Figures 2.13 to 2.15, the range of observed (f + l – a) is 25˚ to 55˚ (except for the nickel-chromium and titanium alloys); and the range of l is 20˚ to 45˚. With these Chip formation mechanics 55 Fig. 2.15 φ – λ – α relationships compared for (a) free-machining (o) and non-free machining (•) carbon and low alloy steels; and (b) austenitic stainless and high manganese steels (o), nickel-chromium heat resistant (•) and titanium alloys (+) turned by cemented carbide and ceramic tooling Childs Part 1 28:3:2000 2:37 pm Page 55 numbers, the non-dimensional specific work may be calculated for a range of rake angles. Figure 2.16(a) gives, for rake angles from 0˚ to 30˚, bounds to the specific work for tan(f + l – a) from 0.5 to 1.5 and for l = 20˚ to 45˚. It summarizes the conflicts in designing a machining process for production. For a high rake angle tool (a = 30˚), specific work is relatively low and insensitive to changes in f and l. In such conditions an easily controlled and high quality process could be expected; but only high speed steel tools are tough enough to survive such a slender edge geometry (at least in sharp-edged, plane rake face form). At the other extreme (a = 0˚), cutting edges can withstand machining stresses, but the specific work is high and extremely sensitive to small variations in friction or shear plane angle. In practice, chamfered and grooved rake faces are developed to overcome these conflicts, but that is for a later chapter. Of the total specific work, some is expended on primary shear deformation and some on rake face friction work. The specific primary shear work, U p , is the product of shear force kfd/sinf and velocity discontinuity on the plane (equation (2.3)). After ‘non-dimen- sionalizing’ with respect to kfd, U p cosa —— = ——————— (2.12) kfd sin f cos(f < a) which is the same as the shear strain g of equation (2.4a). The percentage of the primary work to the total can be found from the ratio of equation (2.12) to (2.11). For the same ranges of numbers as used in Figure 2.16(a), the percentage ranges from more than 80% when tan(f + l – a) = 0.5, through more than 60% when tan(f + l – a) = 1.0, to as little as 50% when tan(f + l – a) = 1.5. The distribution of work between the primary shear region and the rake face is important to considerations of temperature increases in machin- ing. Temperature increases are the subject of Section 2.3. Finally, equations (2.5) can be used to determine the normal and friction forces on the tool face, and can be combined with equations (2.6) and (2.2) for the contact length between the chip and tool, in terms of the feed, to create expressions for the average normal and friction contact stresses on the tool: 56 Chip formation fundamentals Fig. 2.16 Ranges of (a) dimensionless specific cutting force, (b) maximum normal contact stress and (c) maximum fric- tion stress, for observed ranges of φ , λ , α (º) and m / n Childs Part 1 28:3:2000 2:37 pm Page 56 s n n 2cos 2 lt n n 2cos l sin l ( —— ) av. = — —————— ; ( —— ) av. = — —————— (2.13) kmsin2(f + l < a) kmsin2(f + l < a) In Section 2.2.3, the influence of m/n on contact stress distribution was considered, lead- ing to Figure 2.12. The same considerations can be applied to deriving the peak contact stresses associated with the average stresses of equations (2.13). Figures 2.16(b) and (c) show ranges of peak normal and friction stress for the same data as given in Figure 2.16(a), for the practically observed range of m/n from 1.3 to 3.5. Peak normal stress ranges from one to three times k. Peak friction stress is calculated to be often greater than k. This, of course, is not physically realistic. The loads in machining are so high, and the lubrication so poor, that the classical law of friction – that friction stress is proportional to normal stress – breaks down near the cutting edge. Section 2.4 gives alternative friction modelling, first widely disseminated by Shaw (1984). It has already been mentioned that the focus of this introductory mechanics section is descriptive and not predictive. However, the earliest predictive models for shear plane angle have been introduced – equations (2.9) and (2.10). In most cases, they give upper and lower bounds to the experimental observations. It may be asked what is the need for better prediction? The answer has two parts. First, as shown in Figure 2.16(a), the specific forces in machining (and hence related characteristics such as temperature rise and machined surface quality) are very sensitive to small variations in shear plane angle, for commonly used values of rake angle. Secondly, the cutting edge is a sacrificial part in the machining process, with an economic life often between 5 and 20 minutes (see Chapter 1). Small variations in mechanical characteristics can lead to large variations in economic life. It is the economic pressure to use cutting edges at their limit that drives the study of machining to ever greater accuracy and detail. 2.3 Thermal modelling If all the primary shear work of equation (2.12) were converted to heat and all were convected into the chip, it would cause a mean temperature rise DT 1 in the chip k cosa kg DT 1 = —— ——————— ≡ —— (2.14) rC sin f cos(f < a) rC where rC is the heat capacity of the chip material. Table 2.2 gives some typical values of k/(rC). Given the magnitudes of shear strains, greater than 2, that can occur in machining (Section 2.2), it is clear that significant temperature rises may occur in the chip. This is without considering the additional heating due to friction between the chip and tool. It is important to understand how much of the heat generated is convected into the chip and what are the additional temperature rises caused by friction with the tool. The purpose of this section is to identify by simple analysis and observations the main parameters that influence temperature rise and their approximate effects. The outcome will be an understanding of what must be included in more complicated numerical models (the subject of a later chapter) if they are also to be more accurate. Thus, the simple view of chip formation, that the primary and secondary shear zones are planar, OA and OB of Thermal modelling 57 Childs Part 1 28:3:2000 2:37 pm Page 57 Figure 2.17(a), will be retained. Convective heat transfer that controls the escape of heat from OA to the workpiece (Figure 2.17(b)) is the focus of Section 2.3.1. How friction heat is divided between the chip and tool over OB (Figure 2.17(c)) and what temperature rise is caused by friction is the subject of Section 2.3.2. The heat transfer theory necessary for all this is given in Appendix 2. 2.3.1 Heating due to primary shear The fraction of heat generated in primary shear, b, that flows into the work material is the main quantity calculated in this section. When it is known, the fraction (1 – b) that is carried into the chip can also be estimated. The temperature rise in the chip depends on it. 58 Chip formation fundamentals Table 2.2 Mechanical and physical property data for machining heating calculations Work Carbon/low Copper Aluminium Ni-Cr Titanium material alloy steels alloys alloys alloys alloys k [MPa] 400–800 300–500 120–400 500–800 500–700 ρ C [MJ/m 3 ] ≈ 3.5 ≈ 3.5 ≈ 2.5 ≈ 4.0 ≈ 2.2 k/ ρ C 110–220 85–140 50–160 120–200 220–320 ∆T 1 [°C] a 230–470 180–300 110–340 250–430 470–680 K work [W/m K] 25–45 100–400 100–300 15–20 6–15 K tool b [W/m K] 20–50 80–120 100–500 80–120 50–120 K* 0.5–2 0.2–1 0.3–5 4–8 3–20 a ∆T 1 for γ ≈ 2.5 and β = 0.85; b tool grades appropriate for work materials. Fig. 2.17 (a) Work, chip and tool divided into (b) work and (c) chip and tool regions, for the purposes of temperature calculations Childs Part 1 28:3:2000 2:37 pm Page 58 Figure 2.17(b) shows a control volume AA′ fixed in the workpiece. The movement of the workpiece carries it both towards and past the shear plane with velocities u˘ z and u˘ x ,as shown. u˘ ˘z = U work sinf and u˘ x = U work cosf. When the control volume first reaches the shear plane (as shown in the figure), it starts to be heated. By the time the control volume reaches the cutting edge (at O), some temperature profile along z is established, also as shown in the figure. The rate of escape of heat to the work (per unit depth of cut), by convection, is then the integral over z of the product of the temperature rise, heat capacity of the work and the velocity u˘ x : ∞ Q convected to work = ∫ u˘ x (T – T o )rC dz (2.15a) 0 The temperature profile (T – T 0 ) is given in Appendix 2.3.1: once a steady state tempera- ture is reached along Oz ∞ u˘ x u˘ x q 1 k Q convected to work = ∫ —— q 1 e –u˘ z z/k dz ≡ ——— (2.15b) 0 u˘ z u˘ 2 z where q 1 is the shear plane work rate per unit area and k is the thermal diffusivity of the work material. The total shear plane heating rate per unit depth of cut is the product of q 1 and the shear plane length, q 1 (f/sinf). The fraction b of heat that convects into the work is the ratio of equation (2.15b) to this. After considering that equation (2.15b) is a maximum estimate of heat into the work (the steady temperature distribution might not have been reached), and also after substituting for values of u˘ x and u˘ z in terms of U work k b ≤ ————— (2.16) U work f tan f According to equation (2.16), the escape of heat to the work is controlled by the ther- mal number [U work f tanf/k]. This has the form of the Peclet number, familiar in heat trans- fer theory (Appendix A2.3.2). The larger it is, the less heat escapes and the more is convected into the chip. A more detailed, but still approximate, analysis has been made by Weiner (1955). Equation (2.16) agrees well with his work, provided the primary shear Peclet number is greater than 5. For lower values, equation (2.16), considered as an equal- ity, rapidly becomes poor. Figure 2.18(a) compares Weiner’s and equation (2.16)’s predictions with experimental and numerical modelling results collected by Tay and reported by Oxley (1989). Weiner’s result is in fair agreement with observation. b varies only weakly with [U work f tanf/k]: a change of two orders of magnitude, from 0.1 to 10, is required of the latter to change b from 0.9 to 0.1. There is evidence that as [U work f tanf/k] increases above 10, b becomes limited between 0.1 and 0.2. This results from the finite width of the real shear plane. The implication from Figure 2.18(a) is that numerical models of primary shear heating need only include the finite thickness of the shear zone if [U work f tanf/k] > 10, and then only if (1 – b), the fraction of heat convected into the work, needs to be known to better than 10%. Figure 2.18(b) takes the mean observed results in Figure 2.18(a) and, for f = 25˚, converts them to relations between U work and f that result in b = 0.15 and 0.3, for k = 3, 12 and 50 mm 2 /s. These values of k are representative of heat resistant alloys (stainless steels, Thermal modelling 59 Childs Part 1 28:3:2000 2:37 pm Page 59 nickel and titanium alloys), carbon and low alloy steels, and copper and aluminium alloys respectively. The speed and feed combinations that result coincide with the speed/feed ranges that are used in turning and milling for economic production (Chapter 1). In turn- ing and milling practice, b ≈ 0.15 is a reasonable approximation (actual variations with cutting conditions are considered in more detail in Chapter 3). A fraction of primary shear heat (1 – b), or 0.85, then typically flows into the chip. The DT 1 of Table 2.2 give primary zone temperature rises when f ≈ 25˚ and b = 0.85. For carbon and low alloy steels, copper and Ni-Cr alloys, these rises are less than half the melting temperature (in K): plastic flow stays within the bounds of cold working. However, for aluminium and titanium alloys, temperatures can rise to more than half the melting temperature: microstructural changes can be caused by the heating. Given that the primary shear acts on the workpiece, these simple considerations point to the possibility of workpiece thermal damage when machin- ing aluminium and titanium alloys, even with sharp tools. The suggested primary shear temperature rise in Table 2.2 of up to 680˚C for titanium alloys is severe even from the point of view of the edge of the cutting tool. The further heating of the chip and tool due to friction is considered next. 2.3.2 Heating due to friction The size of the friction stress t between the chip and the tool has been discussed in Section 2.2.5. It gives rise to a friction heating rate per unit area of the chip/tool contact of q f = tU chip . Of this, some fraction a* will flow into the chip and the remaining fraction (1 – a*) will flow into the tool. The first question in considering the heating of the chip is what is the value of a*? The answer comes from recognizing that the contact area is common to the chip and the tool. Its temperature should be the same whether calculated from the point of view of the flow of heat in the tool or from the flow of heat in the chip. Exact calculations lead to the conclusion that a* varies from point to point in the contact. Indeed so does q f . To cope with such detail is beyond the purpose of this section. Here, an approximate analysis is devel- oped to identify the physically important properties that control the average value of a* 60 Chip formation fundamentals Fig. 2.18 (a) Theoretical (—, ) and observed (hatched region) dependence of β on [ U work f tan φ / κ ]; (b) iso- β lines ( β = 0.15 and 0.3) mapped onto a ( U work , f ) plane for κ = 3, 12 and 50 mm 2 /s and φ = 25º Childs Part 1 28:3:2000 2:37 pm Page 60 and to calculate the average temperature rise in the contact. It is supposed that q f and a* are constant over the contact, and that a* takes a value such that the average contact temperature is the same whether calculated from heat flow in the tool or the chip. Figure 2.17(c) shows the situation of q f and a* constant over the contact length l between the chip and tool. The contact has a depth d (depth of cut) normal to the plane of the figure. As far as the tool is concerned, there is heat flow into it over the rectangle fixed on its surface, of length l and width d. Appendix A2.2.5 considers the mean temperature rise over a rectangular heat source fixed on the surface of a semi-infinite solid. To the extent that the nose of the cutting tool in the machining case can be regarded as a quadrant of a semi-infi- nite solid, equation (A2.14) of Appendix 2 can be applied to give (1 – a*)t av U chip l (T – T 0 ) av.tool contact = s f ——————— (2.17) K tool where T 0 is the ambient temperature, K is thermal conductivity and s f is a shape factor depending on the contact area aspect ratio (d/l): for example, its value increases from 0.94 to 1.82 as d/l increases from 1 to 5. As far as the chip is concerned, it moves past the heat source at the speed U chip . Its temperature rise is governed by the theory of a moving heat source. This is summarized in Appendix A2.3. When the Peclet number U chip l/(4k) is greater than 1, heat conducts a small distance into the chip compared with the chip thickness, in the time that an element of the chip passes the heat source. In this condition, equation (A2.17b) of Appendix 2 gives the average temperature rise due to friction heating. Remembering that the chip has already been heated above ambient by the primary shear, kg a*t av U chip l k work 1 / 2 (T – T 0 ) av.chip contact = (1 – b) ———— + 0.75 ————— ( ——— ) (2.18) (rC) work K work U chip l Equating (2.17) to (2.18) leads, after minor rearrangement, to an expression for a*: t av U chip l k work 1 / 2 K work t av (rC) work a* —— ——— [ 0.75 ( ——— ) + s f ——— ] = s f —— ———— U chip l – (1 – b) (kg) k work U chip lK tool (kg) K tool (2.19) t av is related to k, l to f and U chip to U work by functions of f, l, a and (m/n), as described previously, by combining equations (2.2), (2.3), (2.6) and (2.13). g is also a function of f and a. After elimination of t av , l and U chip in favour of k, f and U work , equation (2.19) leads to 0.75 K tool n cos l cos(f – a)tanf 1 / 2 k work 1 / 2 a* [ 1 + —— —— ( — ———————— )( ————— ) ] s f K work m sin(f + l – a) U work f tanf (2.20a) (1 – b) K tool cos a cos(f + l – a) = 1 – ————————— ( ——— ) ————————— s f [U work f tan f/k work ] K work sin l cosf Thermal modelling 61 Childs Part 1 28:3:2000 2:37 pm Page 61 The manipulation has introduced the thermal number [U work f tanf/k work ]. b depends on this too (Figure 2.18(a)). If typical ranges of f, l, a and (m/n), from Figures 2.10, 2.14 and 2.15 are substituted into equation (2.20a), the approximate relationship is found (0.45 ± 0.15) K tool k work 1 / 2 a* [ 1 + —————— ( ——— )( ————— )] s f K work U work f tan f (2.20b) (1.35 ± 0.5) (1 – b) K tool ≈ 1 – ————— ———————— ( ——— ) s f [U work f tan f/k work ] K work Figure 2.19(a) shows predicted values of a* when observed b values from Figure 2.18(a) and the mean value coefficients 0.45 and 1.35 are used in equation (2.20b). A strong dependence on [U work f tanf/k work ] and the conductivity ratio K* = K tool /K work is seen, and a smaller but significant influence of the shape factor s f . Predictions are only shown for [U work f tanf/k work ] > 0.5: at lower values the assumption behind equation (2.18), that U chip 1/(4k) is greater than 1, is invalid; and anyway friction heating becomes small and is not of interest. As a matter of fact, the assumption starts to fail for [U work f tanf/k work ] < 5. Figure 2.19(a) contains a small correction to allow for this, according to low speed moving heat source theory (see Appendix A2.3.2). Figure 2.19(a) reinforces the critical importance of the relative conductivities of the tool and work. When the tool is a poorer conductor than the work (K* < 1), the main propor- tion of the friction heat flows into the chip. As K* increases above 1, this is not always so. Indeed, a strong possibility develops that a* < 0. When this occurs, not only does all the friction heat flow into the tool, but so too does some of the heat generated in primary shear. The physical result is that the chip cools down as it flows over the rake face and the hottest part of the tool is the cutting edge. When a* > 0, the chip heats up as it passes over the tool: the hottest part of the tool is away from the cutting edge. 62 Chip formation fundamentals Fig. 2.19 Dependence of (a) α * and (b) friction heating mean contact temperature rise on [ U work f tan φ / κ work ], K* = K tool /K work from 0.1 to 10; s f = 1 (—) and 2 (- . -) Childs Part 1 28:3:2000 2:37 pm Page 62 [...]... the metal cutting process J Appl Phys 16, 31 8 32 4 Oxley, P L B (1989) Mechanics of Machining Chichester: Ellis Horwood Shaw, M C (1984) Metal Cutting Principles, Ch 13 Oxford: Clarendon Press Shirakashi T and Usui, E (19 73) Friction characteristics on tool face in metal machining J JSPE 39 , 966–972 Taylor, F W (1907) On the art of cutting metals Trans ASME 28, 31 35 0 Trent, E M (1991) Metal Cutting, 3rd... a channel much wider than its height h3 p 2 M v lpUchip = the larger of 3. 3 × 10–10 — —— ——— h qT rliquid ( ) 2 /3 (Poiseuille) (2.29a) or ( M 0.71h2pv ————— q 3 r4 T liquid ) 1/6 (Knudsen) (2.29b) For oxygen, at its normal partial pressure in air of ≈ 2 × 104 Pa, and M = 32 , rliquid = 1145 kg/m3, h = 20 × 10–6 Pa s, qT = 2 93 and for h = 0.5 mm, lpUchip = 3. 4 (2 .30 a) This is about half the value given... Brass/carbide C steel/carbide Low alloy steel/ Carbide αº Uwork [m/min] f [mm] k [MPa] µ m Data derived from 20 20 30 10 0 50 50 48 46 100 0.2 0.2 0 .3 0 .3 0.2 130 33 5 450 600 600 1.4 0.9 0.9 1 .3 1 .3 0.95 0.75 0.95 0.8 0.8 Kato et al (1972) Kato et al (1972) Shirakashi and Usui (19 73) Shirakashi and Usui (19 73) Childs and Maekawa (1990) stress approaches the shear flow stress of the work material; at low normal... Proc I Mech E Lond pp 30 1 34 5 and plates 35 –47 Wakabayashi, T., Williams, J A and Hutchings I M (1995) The kinetics of gas phase lubrication in the orthogonal machining of an aluminium alloy Proc I Mech E Lond 209Pt.J, 131 – 136 Weiner, J H (1955) Shear plane temperature distribution in orthogonal cutting Trans ASME 77, 133 1– 134 1 Williams, J A (1977) The action of lubricants in metal cutting J Mech Eng... Elastic effects in metal cutting chip formation Int J Mech Sci 22, 457–466 Childs, T H C (1980b) The sliding wear mechanisms of metals, mainly steels Tribology International 13, 285–2 93 Childs, T H C (1988) The mapping of metallic sliding wear Proc I Mech E Lond 202 Pt C, 37 9 39 5 Childs, T H C and Maekawa, K (1990) Computer aided simulation of chip flow and tool wear Wear 139 , 235 –250 Childs, T H... and tool in machining Trans ASME J Eng Ind 94B, 6 83 689 Kobayashi, S and Thomsen, E G (1959) Some observations on the shearing process in metal cutting Trans ASME J Eng Ind 81B, 251–262 Lee, E H and Shaffer, B W (1951) The theory of plasticity applied to a problem of machining Trans ASME J Appl Mech 18, 405–4 13 Mallock, A (1881–82) The action of cutting tools Proc Roy Soc Lond 33 , 127– 139 Merchant,... superfinished insert tools Childs Part 1 28 :3: 2000 2 :38 pm Page 73 Friction, lubrication and wear 73 Table 2.4 Tool surface roughness and contact stress severity data Tool finish Roughness data Ra [µm] ∆q, ° 10klocal/E*, ° Al/ Cu/ HSS HSS Brass/ Carbide Steel/ Carbide CVD coated Ground Super-finished 0.2–0.5 0.1–0.25 0. 03 1.2 1.2 1.2 2.8 2.8 2.8 1.8 1.8 1.8 3 7 2–4 0.4 1.9 1.9 1.9 and PE2 in Figure 2.25... flow and tool wear Wear 139 , 235 –250 Childs, T H C., Richings, D and Wilcox, A B (1972) Metal cutting: mechanics, surface physics and metallurgy Int J Mech Sci 14, 35 9 37 5 Eggleston, D M., Herzog, R and Thomsen, E G Some additional studies of the angle relationships in metal cutting Trans ASME J Eng Ind 81B, 2 63 279 Herbert, E G (1928) Report on machinability Proc I Mech E London ii, 775–825 Kato,... even then K is found to be only 10–2 to 10 3, compared with the value of 1 /3 predicted above Finally, if abrasive conditions do exist, K is found between 10–1 and 10–4, depending on whether the abrasive is fixed on one surface (2-body) or is loose (3- body) What is the relevance of this to metal machining? In Chapter 1, it was described how the economics of machining lead to the use of, for example,... and noting that H ≡ 5k, values of K, from equation 2 .31 (b), are 4 × 10–8 on the flank, up to 3 × 10–7 on the rake (the speed of the chip was Childs Part 1 28 :3: 2000 2 :38 pm Page 79 Summary 79 Fig 2 .31 (a) Flank and crater tool wear regions, with typical (b) flank and (c) crater wear observations half that of the work) Considering that s/k is large in machining, these values are smaller than expected from . 500–700 ρ C [MJ/m 3 ] ≈ 3. 5 ≈ 3. 5 ≈ 2.5 ≈ 4.0 ≈ 2.2 k/ ρ C 110–220 85–140 50–160 120–200 220 32 0 ∆T 1 [°C] a 230 –470 180 30 0 110 34 0 250– 430 470–680 K work [W/m K] 25–45 100–400 100 30 0 15–20 6–15 K tool b [W/m. (1972) Cu/HSS 20 50 0.2 33 5 0.9 0.75 Kato et al. (1972) Brass/carbide 30 48 0 .3 450 0.9 0.95 Shirakashi and Usui (19 73) C steel/carbide 10 46 0 .3 600 1 .3 0.8 Shirakashi and Usui (19 73) Low alloy steel/. of g = 2.5 and f = 25˚ have Thermal modelling 63 Childs Part 1 28 :3: 2000 2 :37 pm Page 63 been arbitrarily chosen. A feed of 0.25 mm and K tool = 30 W/m K (typical of a high speed steel tool and

Ngày đăng: 13/08/2014, 09:20

TỪ KHÓA LIÊN QUAN