CCNA final _part2 potx

Refer to the exhibit. All edge ports are configured with the spanning-tree portfast command. Host1 is recently connected to port Fa0/1 on switch SW1 . Which statement is true about the status of port Fa0/1? The port will transition into blocking state. The port will transition immediately into forwarding state. The port will transition into blocking state and then immediately into forwarding state. The port will transition into blocking state and immediately transition through the listening and learning states. 26 What three tasks should be performed before moving a Catalyst switch to another VTP management domain? (Choose three.) Select the correct VTP mode and version. Configure the switch with the name of the new management domain. Download the VTP database from the VTP server in the new domain. Configure the VTP server in the new domain to recognize the BID of the switch. Reset the VTP counters to allow the switch to synchronize with the other switches in the new domain. Verify that the switch has a lower configuration revision number than the other switches in the new domain. 27 Which type of frame contains information that is used in the election of the spanning tree root bridge? BID LSA LSU BPDU 28 This is trial version www.adultpdf.com Refer to the exhibit. After receiving a console notification on Switch2, the network administrator begins to troubleshoot the trunk link between Switch1 and Switch2. Which configuration change can be made to correct the problem with the trunk link? Set the Fa0/1 interface on Switch2 to trunk mode. Change the trunk encapsulation on Switch2 Fa0/1 to dot1q. Change the native VLAN on Switch2 interface Fa0/1 to VLAN 100. Change the access mode VLAN on Switch2 to the default VLAN 1. 29 Using the command copy tftp:backup.cfg startup-config, an administrator downloaded a saved configuration from a TFTP server to a switch. Why does the administrator not detect any changes in the switch configuration after the download completes? The command should have been copy startup-config tftp:backup.cfg. A backup configuration from a TFTP server cannot be copied directly into the startup-config. The command copy running-config startup-config should be used to save the changes on the switch. Downloading to the startup-config requires the switch to be reloaded in order for the configuration to take effect. 30 This is trial version www.adultpdf.com Refer to the exhibit. A network administrator configures HyperTerminal with the parameters shown but is unable to connect to a switch via the console port. The administrator is using a tested rollover cable attached to the only COM port on the computer, and the connections have been verified. What is the likely problem? The cable is connected to the wrong port. The wrong connection speed is selected. The cable is the wrong type. The flow control setting is not correct. The stop bits should be set to zero. Close Window Assessment System 1. Assessment Selection 2. Assessment Settings 3. Take Assessment Take Assessment - ESwitching Practice Final Exam - CCNA Exploration: LAN Switching and Wireless (Version 4.0) 11570 Time Remaining: 31 This is trial version www.adultpdf.com Refer to the exhibit. RTB is configured for traditional inter-VLAN routing. RTB can ping computer A but cannot ping computer B. What is a possible cause of this failure? Port Fa0/11 is in the wrong VLAN. RTB does not have an active routing protocol. The IP address of computer B is in the wrong logical network. Router interface Fa0/1 has the wrong trunk encapsulation type configured. 32 Refer to the exhibit. A network administrator has segmented the network into two VLANs and configured R1 and S1 as displayed. However, PC1 is unable to access PC2. What is the likely problem? No routing protocol is configured on R1. The Fa0/1 port of S1 is not a trunk port. The default gateway address is not set on S1. Only one physical link between S1 and R1 is configured for inter-VLAN routing. 33 This is trial version www.adultpdf.com Refer to the exhibit. A network administrator issues the command shown on Switch1. What are two possible reasons that ports Fa0/1 through Fa0/4, and ports Fa0/11 and Fa0/12 do not show in the command output? (Choose two.) The ports have been configured as trunks. The ports have been assigned to the native VLAN. The VLAN that they are assigned to has been deleted. The ports currently do not have any devices plugged into them. The no shutdown command was not issued on these ports. 34 Refer to the exhibit. A company has acquired a new office in a campus environment. Switches in the existing This is trial version www.adultpdf.com office and the new office are directly connected by a trunk link. The VLANs and IP addressing are setup as shown in the exhibit. The computers in each office are not able to ping each other. What will fix the problem? Use an access link between S2 and S3. Connect S2 and S3 to a common router. Set the subnet mask in the new office to /24. Configure the new office default gateway to 172.17.10.1 Change the port assignments in the new office to a different VLAN. 35 Which parameter is a specific frequency at which a wireless access point will operate? BSS WEP SSID ad hoc channel 36 Refer to the exhibit. Both switches are configured with default bridge priority. Which port will act as the STP root port if all links are operating at the same bandwidth? Fa0/1 interface of S1 Fa0/2 interface of S1 Fa0/1 interface of S2 Fa0/2 interface of S2 37 A wireless access point can function as which type of shared medium, wired LAN device? hub switch router gateway This is trial version www.adultpdf.com 38 Refer to the exhibit. Which statement is true regarding the information shown? Only one VLAN is currently configured to use the trunk links. The switch negotiated trunk links for interfaces Fa0/1 and Gi0/1. A Cisco proprietary protocol is in use for interfaces Fa0/1 and Gi0/1. Interfaces Gi0/1 and Fa0/1 are allowed to carry data from multiple VLANs. 39 After unpacking a new Linksys WRT300N wireless multifunction device, a user needs to change the default administrator password and make other configuration changes. What must the user do to access the device in order to make these changes? Use a wireless client to associate with the WRT300N and then open a HyperTerminal session with the device. Establish a wired connection with the device and then reboot the attached computer to launch the configuration software. Establish a wired connection from a computer in the same IP subnet as the WRT300N and enter the default IP address of the device into a web browser on the computer. Modify the TCP/IP properties of the computer that is connected to the WRT300N so that the computer and the WRT300N exist on the same network. Then reboot the computer to establish a connection. 40 Refer to the exhibit. A new host needs to be connected to VLAN 20. Which IP address should be assigned to this new host? 172.16.10.68 /27 This is trial version www.adultpdf.com 172.16.10.99 /28 172.16.10.110 /27 172.16.30.96 /27 172.16.30.120 /28 172.16.30.146 /27 41 What happens when the crypto key zeroize rsa command is entered on a switch configured with the transport input ssh command on the vty lines? A new RSA key pair is created. The switch defaults to allowing Telnet connections only. The switch is no longer able to make SSH connections as an SSH client. The switch allows remote connections only after a new RSA key pair is generated. 42 Refer to the exhibit. What is the purpose of the configuration commands that are shown? to activate port Fa0/10 to make the port a member of VLAN 30 to activate port security on port Fa0/10 to add VLAN 30 to the trunk that is connected to port Fa0/10 43 Refer to the exhibit. All switches are configured with the default bridge priority. Which port will act as a non- designated port if all links are operating at the same bandwidth? This is trial version www.adultpdf.com Fa0/1 interface of switch A Fa0/2 interface of switch A Fa0/1 interface of switch B Fa0/2 interface of switch B Fa0/1 interface of switch C Fa0/2 interface of switch C 44 How does Spanning Tree Protocol aid network architecture? allows for redundant links by eliminating loops provides greater scalability by eliminating collisions reduces switch processor load by reducing broadcast traffic on trunk links reduces administrative overhead by sharing VLAN databases between switches across the network 45 Refer to the exhibit. All hosts are in listen mode. Host 1 and Host 4 both transmit data at the same time. How do the hosts respond on the network? (Choose two.) After the end of the jam signal, a backoff algorithm is invoked. Hosts 1 and 4 are operating full duplex so no collision will exist. The hub will block the port connected to Host 4 to prevent a collision. Hosts 1 and 4 are assigned shorter backoff values to provide them priority to access the media. If a host has data to transmit after the backoff period of that host, the host checks to determine if the line is idle before transmitting. Showing 3 of 4 <Prev Page: 3 Next> Close Window All contents copyright 1992-2011 Cisco Systems, Inc. Privacy Statement and Trademarks. This is trial version www.adultpdf.com 3 This is trial version www.adultpdf.com . Assessment Settings 3. Take Assessment Take Assessment - ESwitching Practice Final Exam - CCNA Exploration: LAN Switching and Wireless (Version 4.0) 11570 Time