Moldflow 1 Part 11 pptx

User Components ¾ Click ¾ Open a Sketch. ¾ Add point .x=70, y=-50 (middle of right hand side hole). ¾ Close sketch. ¾ Key in Face Offset to be 300. ¾ Validate , 5-33 MoldWorks2006 Tutorial User Components 5.3.4 Creating Connector plugs component ¾ Activate the Add User Part icon. ¾ Select the Component tab and click the user part selection icon . ¾ Select NConnector part. ¾ Click to be Instance. ¾ Select the N91_4A configuration. ¾ Click . ¾ Select front face of plate3. ¾ Click . 5-34 MoldWorks2006 Tutorial User Components ¾ Open a Sketch. ¾ Add point x=-195 y=-50 (middle of the left hand side hole) ¾ Close the Sketch. ¾ Scroll Face Offset parameter to 22. ¾ Click . ¾ Click . 5-35 MoldWorks2006 Tutorial User Components ¾ Select NConnector part. ¾ Click to be Instance. ¾ Select the N91_4A configuration. ¾ Click . ¾ Select back face of plate3. ¾ Click . ¾ Open a Sketch. ¾ Add point x=-195 y=-50 (middle of the left hand side hole). ¾ Close the Sketch. ¾ Scroll Face Offset parameter to 22. ¾ Click . ¾ Validate , 5-36 MoldWorks2006 Tutorial User Components ¾ Select right face of plate3. ¾ Click . ¾ Select Sketch6 from Design tree manager ¾ Click . ¾ Validate . 5-38 MoldWorks2006 Tutorial 6-1 MoldWorks2006 Tutorial 6 6 Lifters In this chapter we will show how to integrate lifters for releasing internal undercuts of the plastic part. The mold in this exercise is a multi cavity mold of two cavities. This is in order to demonstrate the full automatic functionality of the lifters. Lifters are added automatically to all instances of the core inserts. Internal Undercut Lifters 6.1 Declaration of the core inserts. ¾ Open Mold.SLDASM from …\Example Files\Lifters_EX ¾ Add the Cores assembly as inserts . ¾ Make sure to set the type of the inserts as Core 6-2 MoldWorks2006 Tutorial Lifters Setting the insert type as Core is essential for the lifters and ejector trim functionality. However if this step was missed or you set the insert type by mistake to another type you can always modify this setting via the Attribute mechanism. In case the core is a solid part of the core plate (not added as insert) you should set the plate type to Core via the Attribute mechanism before adding lifters or trimmed ejectors. ¾ Add the cavities inserts following the same steps. Make sure to set the insert type to Cavity. ¾ Activate New Mold . The mold estimation should give a mold size of 2020. ¾ Set the mold Type to Plates Only. ¾ Change the plate thickness of Plate4/5 to 96 mm. This is to fit the lifters in. ¾ Click create button . ¾ Display only the mobile side of the mold by selecting Mobile Side from the Display Configuration property manager page. 6-3 MoldWorks2006 Tutorial Lifters 6.2 Adding the Lifters. ¾ Activate Add Lifters . ¾ Press the Lifters Library – the first step of the add lifter steps tool bar. ¾ Select the DME Lifters library. ¾ Select FLAT_CORSinch lifters and press Continue. 6-4 MoldWorks2006 Tutorial Lifters ¾ Select the ULB-2003-5-16 configuration. ¾ Press Continue twice go directly to the Lifter Placement step. Omit the Face step since the default face is set according to the lifter manufacturers recommendations. ¾ Make sure you are in the front view with wire frame display. ¾ Key the following data: (to position the lifter) o DX = -37.0 mm o DY = 54.0 mm o Rotate = 180.0 Deg 6-5 MoldWorks2006 Tutorial [...]... the edge where the insert is going to cut, since it is a rounded edge and just part of the wire frame and not a real edge) The angle value is extracted from the selected edge and set to 5 deg The preview is updated accordingly Press Continue to go to the Lifter Stroke step Set the parameters as follows: Stroke = 2.5 mm H1 = 46.0 mm H2 = 20.0 mm MoldWorks2006 Tutorial 6-6 Lifters Change to isometric . Activate the Add User Part icon. ¾ Select the Component tab and click the user part selection icon . ¾ Select NConnector part. ¾ Click to be Instance. ¾ Select the N 91_ 4A configuration Select NConnector part. ¾ Click to be Instance. ¾ Select the N 91_ 4A configuration. ¾ Click . ¾ Select back face of plate3. ¾ Click . ¾ Open a Sketch. ¾ Add point x= -19 5 y=-50 (middle. MoldWorks2006 Tutorial 6 -1 MoldWorks2006 Tutorial 6 6 Lifters In this chapter we will show how to integrate lifters for releasing internal undercuts of the plastic part. The mold in this