Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống
1
/ 25 trang
THÔNG TIN TÀI LIỆU
Thông tin cơ bản
Định dạng
Số trang
25
Dung lượng
1,07 MB
Nội dung
[...]... 5.74 1. 79 0. 41 0. 41 0.20 0 .13 0 .15 0 .15 19 ppm For C7+; mol wt = 14 7, Pc = 304psia, Tc = 1, 112 °R Condemate — 60 bbl/MMscf, 52.3 °APJ Initial free-water production — 0 bbl/MMscf Final free-water production — 15 bbl/MMscf (at surface conditions) Gas sales requirements — 1, 000 psi, 7 Ib/MMscf, '/4 grain H2S, 2% CO2 6 Design of GAS-HANDLING Systems and Facilities Chapter 9 discusses the refrigeration and. .. covered in Volume 1 Figure 1- 1 is a block diagram of a production facility that is primarily designed to handle gas wells The well flow stream may require heating prior to initial separation Since most gas wells flow at high pressure, a "•"Reviewed for the 19 99 edition by Folake A Ayoola of Paragon Engineering Services, Inc 1 2 Design of GAS-HANDLING Systems and Facilities Figure 1 -1 Gas field facility... oil and water * Reviewed for the 19 99 edition by K S Chiou of Paragon Engineering Services, Inc 8 Design of GAS-HANDLING Systems and Facilities MECHANISMS OF HEAT TRANSFER There are three distinct ways in which heat may pass from a source to a receiver, although most engineering applications are combinations of two or three These are conduction, convection, and radiation Conduction The transfer of. .. difference between the hot and cold liquid, and the heat transfer area It is expressed: 10 where Design of GAS-HANDLING Systems and Facilities q = heat transfer rate, Btu/hr A = heat transfer area, ft2 AT = temperature difference, °F h = film coefficient, Btu/hr~ft 2 ~°F The proportionality constant, h, is influenced by the nature of the fluid and the nature of the agitation and is determined experimentally... delivered to them, and periodic tests are made to ascertain that requirements are being fulfilled by the seller 4 Design of GAS-HANDLING Systems and Facilities Acid gases, usually hydrogen sulfide (H2S) and carbon dioxide (CO2) are impurities that are frequently found in natural gas and may have to he removed Both can be very corrosive, with CO2 forming carbonic acid in the presence of water and H2S potentially... understand the lectures and carry out their assignments Of more importance, the material that did exist usually contained nomographs, charts, and rules of thumb that had no reference to the basic theories and underlying assumptions upon which they were based Although this text often relies and builds upon information that was presented in Surface Production Operations, Volume I: Design of Oil-Handling Systems. .. pressure) of any pipe/equipment system is set by a relief valve For this reason, a section on pressure relief has been included Since safety considerations are so important in any facility design, Chapter 14 has been devoted to safety analysis and safety system design (Volume 1, Chapter 13 discusses the need to communicate about a facility design by means of flowsheets and presents general comments and several... several examples of project management.) Table 1 -1 describes a gas field The example problems that are worked in many of the sections of this text are for sizing the individual pieces of equipment needed for this field CHAPTER 2 Heat Transfer Theory * Many of the processes used in a gas-handling production facility require the transfer of heat This will be necessary for heating and cooling the gas,... E Arnold, RE Houston, Texas Maurice I Stewart, Ph.D., RE Metairie, Louisiana xiv CHAPTER 7 Overview of Gas-Handling Facilities * The objective of a gas-handling facility is to separate natural gas, condensate, or oil and water from a gas-producing well and condition these fluids for sales or disposal This volume focuses primarily on conditioning natural gas for sales Gas sweetening, the removal of. .. Volume I: Design of Oil-Handling Systems and Facilities, it does present the basic concepts and techniques necessary to select, specify, and size gas-handling, -conditioning, and -processing equipment This volume, which covers about one semester's work or a two-week short course, focuses on areas that primarily concern gas-handling, -conditioning, and -processing facilities Specific areas included are . Anti-Agglomerators, 10 7 CHAPTER S LTX Units and Line Heaters 10 9 LTX Units, 11 0 Line Heaters, 11 2 Heat Duty, 11 3 Fire-Tube Size, 11 5 Coil Sizing, 11 6 Choose Temperatures 11 6, Choose. for the 19 99 edition by Folake A. Ayoola of Paragon Engineering Services, Inc. 1 2 Design of GAS-HANDLING Systems and Facilities Figure 1 -1. Gas field facility block diagram. choke . Design, 13 7 vi Trays and Packing, 14 1 Trays 14 1, Packing 14 5, Trays or Packing 14 8 Condensate Stabilizer as a Gas Processing Plant, 14 9 LTX Unit as a Condensate Stabilizer, 14 9 CHAPTER