1. Trang chủ
  2. » Kỹ Thuật - Công Nghệ

Technical Specifications of Surface Buoy potx

14 202 0

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

THÔNG TIN TÀI LIỆU

Thông tin cơ bản

Định dạng
Số trang 14
Dung lượng 237,95 KB

Nội dung

Envirtech S.p.A. Cap. Sociale Euro 500.000 i.v. Italy 30175 Venezia Marghera (VE) 4/A, Via Pacinotti Phone +39 041 5313400 Fax +39 041 5313400 CCIAA VE 03852470107 - VAT: IT03852470107 Management Italy 17031 Albenga (SV) 69/2, Via Patrioti Phone +39 0182 559643 Fax +39 0182 570976 Branches: Italy 31020 Vidor (TV) , 6/8 Via Sartori Italy 30030 Chirignago (VE) 2, Via S. Caterina e-mail info@envirtech.org web-site www.envirtech.com This document or parts of it cannot be used for scopes not authorized by Envirtech SpA that will protect its rights. Envirtech SpA Venice, 15th February 2011 Envirtech Code: 20003-SPE-200.0 TSUNAMI WARNING SYSTEM Technical Specifications of Surface Buoy Tsunami Warning System Code 20003-SPE-200.0 Date 15/02/2011 Technical Specifications of Surface Buoy Page 2 of 14 TABLE OF CONTENTS 1 SYSTEM OVERVIEW 3 2 SB ARCHITECTURE 4 3 SB FUNCTIONALITIES 10 4 TECHNICAL DESCRIPTION 11 4.1.1 Ballast and Mooring line specifications 11 4.1.2 Buoy Frame specifications 11 4.1.3 Day and Night Signalling devices 11 4.1.4 Autonomous Power supply system 11 4.1.5 Electronic Housing 12 4.2 SATELLITE MODEM 13 4.3 SURFACE ACOUSTIC MODEM 13 5 SB COMPLIANT TABLE 14 Tsunami Warning System Code 20003-SPE-200.0 Date 15/02/2011 Technical Specifications of Surface Buoy Page 3 of 14 1 SYSTEM OVERVIEW The Tsunami Warning System (TWS) designed by Envirtech is composed of the following main subsystems: • an Underwater Module (UM) to be installed at the sea bottom in open sea location for the accurate measurement of the tide and the identification of anomalous conditions. • a Surface Buoy (SB) moored close to the UM to receive via acoustic link the measurement of UM to be transferred via satellite link to a Data Centre (DC) for visualization and analysis. • a Data Centre (DC) on land composed of hardware and software infrastructures for the reception via satellite link of the data of SB and UM to be displayed, stored and analysed. ACOUSTIC LINK SATELLITE LINK UM SB DC Fig. 1.1 – Envirtech TWS Overview The present document deals with the architectural, functional and performance specifications of the Surface Buoy (SB). Tsunami Warning System Code 20003-SPE-200.0 Date 15/02/2011 Technical Specifications of Surface Buoy Page 4 of 14 2 SB ARCHITECTURE The Surface Buoy (SB) system proposed is a SPAR buoy. Spar buoy is characterized by a tall and thin configuration. It floats upright in the water and it is characterized by a small water plane and a large mass. This configuration tends to be a stable ocean platform. Adjustment of the water plane area and the mass allows spar buoys to be tuned so they tend to not respond to wave forcing. The Envirtech SB is composed of 3 main parts: - a subsurface pole; - a buoyant (cone + cylinder) in the middle; - a turret on the top. The main advantages of this configuration for the specific applications are the following: - the lower pole provide a reliable mechanical support of the acoustic modem and related cable: the acoustic transducer can be mounted at least at 5-6m water depth to get a reliable acoustic link. - The buoyant can host on the top in the central part the battery and electronic unit with related connectors. - The turret on the top allows to mount the solar panels, the satellite modems and additional devices like WiFi interface, meteorological station, etc. - The hydrodynamic of the buoy proposed in characterised by small tilt movements: this allows to get a vertical stable platform to optimise the performances of the acoustic link between the buoy and the underwater module to get the data related to the tide and tsunami detection. A block diagram of the buoy proposed is reported in picture 2.1. Tsunami Warning System Code 20003-SPE-200.0 Date 15/02/2011 Technical Specifications of Surface Buoy Page 5 of 14 cd SB Architecture BUOY FRAME WITH SIGNALING DEVICES BALLAST MOORING LINE ELECTRONIC UNIT AUTONOMOUS POWER SUPPLY SUBSYSTEM SATELLITE MODEM WLAN MODEM GPS RECEIVER ACOUSTIC MODEM METEOROLOGICAL STATIONS HEADING & TILT SENSOR Fg. 2.1 – SB Block Diagram It is composed of the parts reported in the following table Device/Component/Part Description Mooring Line and Ballast A line composed of a synthetic ropes, mechanical accessories and 4 tons metal block to anchor the buoy. This parts requires a specific design taking into account the depth and the meteo- marine conditions of the specific installation site. Envirtech can provide the mooring line with related design and dynamical analysis results. Tsunami Warning System Code 20003-SPE-200.0 Date 15/02/2011 Technical Specifications of Surface Buoy Page 6 of 14 Buoy Frame with signaling devices A spar buoy equipped with the signaling devices stated by IALA, IMO and IMA standards and regulations. It integrates mechanically all the parts listed below in the present table. Autonomous Power Supply Subsystem A power supply system composed of solar panels, a battery charger with related control electronic and a lead gel battery pack. Electronic Unit An electronic system integrated in a water proof case Heading & Tilt Sensor A heading and tilt sensor to monitor the buoy movement, integrated in the Electronic Unit. This part is optional and not included in the standard version GPS Receiver A GPS receiver to monitor the buoy position at sea integrated in the Satellite Modem Surface Acoustic Modem An acoustic modem installed at least at 5-6m under the buoy Satellite Modem A satellite modem for the communication with the Data Centre on land. WLAN Modem A device providing a broadband data link with the installation and maintenance ship Meteorological Station A set of meteorological sensors (temperature, humidity, pressure, wind speed and direction) with related acquisition electronic. This part is optional and non included in the standard version Drawings of the SB are reported hereinafter. It can be noted that the SB metal frame is equipped with double supports for Satellite and Acoustic modems because on user request it is possible to provide a redundant configuration. Anyway the standard version is without redundancy. Tsunami Warning System Code 20003-SPE-200.0 Date 15/02/2011 Technical Specifications of Surface Buoy Page 7 of 14 Fig 2.2– Surface Buoy (Main Sizes and Weights) Tsunami Warning System Code 20003-SPE-200.0 Date 15/02/2011 Technical Specifications of Surface Buoy Page 8 of 14 Fig 2.3– Surface Buoy (Detailed Parts) Tsunami Warning System Code 20003-SPE-200.0 Date 15/02/2011 Technical Specifications of Surface Buoy Page 9 of 14 Figure 2.4 –Surface Buoy Tsunami Warning System Code 20003-SPE-200.0 Date 15/02/2011 Technical Specifications of Surface Buoy Page 10 of 14 3 SB FUNCTIONALITIES The main functionalities provided by the SB are summarized hereinafter: • Self monitoring of SB status data composed of o Electronic unit diagnostic status (battery voltage and current, internal temperature, pressure and water intrusion). o Buoy position from GPS receivers and notification of SB OUT or INSIDE a circular zone centred on the mooring point of the SB. • Autonomous transmission of SB status data to the Data Centre (DC) every hour or 2 hours, 3 hours, 4 hours, 6 hours depending on the user settings. • Hourly logging of all SB status data in the internal mass memory. • Generation and transmission on request to the DC of the current SB status data. • Reception, execution and reply to settings commands or data request: o change of the period of autonomous delivery to DC of the SB status data; o ON/OFF of WiFi o Test of SAT link. o Current SB status request. • Reception via Acoustic Transmission System (ATS) of the messages received by the Underwater Module (UM) and forward of these messages to the satellite (SAT) modem. • Reception via SAT modem of the commands/data requests for UM and forward of these messages to the ATS to be sent to UM. • Provide a low level commands menu via test cable or WiFi interface to test each device and component. [...]... 20003-SPE-200.0 Technical Specifications of Surface Buoy Date 15/02/2011 Page 11 of 14 4 TECHNICAL DESCRIPTION The specifications of the main components of the SB are reported in the following paragraphs 4.1 Ballast and Mooring line specifications The design depends to the installation site parameters and its water depth It will be defined in the detail design phase 4.2 Buoy Frame specifications The... design phase 4.2 Buoy Frame specifications The mechanical drawing of the buoy is reported in pictures 2.2 and 2.3 It is a spar type buoy able to remain stable in vertical position and to support Beaufort 11 The buoy body is composed of a central steel pole and a foam body having a diameter of 1.45 m The buoy weight is 2000 kg with a buoyancy of 2750kg All metal parts are zinc protected and epoxy painted... Page 12 of 14 Electronic Housing It is depicted in Fig 4.1 Fig 4.1 - Electronic Housing Technical specifications: • Box in Al and PTFE with 8 underwater connectors for o Satellite Modems o Acoustic Modems o WiFi Box o Power supply • ENV-SB-ELE is dual and composed of o CPU board o Status board o Switch board o DC/DC board Tsunami Warning System 20003-SPE-200.0 Technical Specifications of Surface Buoy. .. It is shown in picture 4.3 below Fig 4.3 – Surface Acoustic Modem Its main features are the following: - Spread spectrum modulation - Omnidirectional - Throughput of 5000 bps - Case designed for 200mwd Tsunami Warning System Code 20003-SPE-200.0 Technical Specifications of Surface Buoy Date 15/02/2011 Page 14 of 14 5 SB COMPLIANT TABLE ID Requirement 1 The buoy shall be spar type to minimize the tilt... It is composed of 4 Solar Panel (Polycrystalline) 50W @12VDC each, and 4 Lead Gel accumulators 110Ah @12VDC each Each Solar panel has a dedicated charge controller to optimise the efficiency of the whole system The accumulators pack can supply the whole system for more than 70 days in case of no sunny conditions Tsunami Warning System 20003-SPE-200.0 Technical Specifications of Surface Buoy 4.5 Code... The system buoy + mooring line shall be able to support Beaufort 11 of wind and sea wave conditions 3 Specific detailed design of the mooring line with related dynamical analysis verification shall be provided for each installation site 4 The buoy shall be predisposed for a redundant configuration of the electronic system and the communication system (satellite and acoustic link) 5 The buoy shall have... Code Date 15/02/2011 Page 13 of 14 Satellite Modem It is depicted in Fig 4.2 Fig 4.2 - Satellite Modem Technical specifications: • • • • • • 4.7 Inmarsat-C Message System Built-In GPS Antenna (12 Channels) RS232 Protocol Message Transfer Rate: 600 bit/sec Message size: Max 10 Kbytes Operating frequencies Rx: 1525.0 – 1559.0 MHz.* Tx: 1626.5 – 1660.5 MHz.* GPS: 1575.42 MHz Surface Acoustic Modem It is... electronic system and the communication system (satellite and acoustic link) 5 The buoy shall have day and night signaling devices IALA compliant with a focal plan at least at 3m over the sea level 6 The buoy shall be equipped with a short range wireless communication system useful for real time communication with a Laptop from the installation and maintenance ship Note . SYSTEM Technical Specifications of Surface Buoy Tsunami Warning System Code 20003-SPE-200.0 Date 15/02/2011 Technical Specifications of Surface Buoy Page 2 of 14 TABLE OF CONTENTS. of Surface Buoy Page 9 of 14 Figure 2.4 Surface Buoy Tsunami Warning System Code 20003-SPE-200.0 Date 15/02/2011 Technical Specifications of Surface Buoy Page 10 of. and performance specifications of the Surface Buoy (SB). Tsunami Warning System Code 20003-SPE-200.0 Date 15/02/2011 Technical Specifications of Surface Buoy Page 4 of 14 2

Ngày đăng: 13/07/2014, 20:20

TỪ KHÓA LIÊN QUAN