ASM INTERNATIONAL ® The Materials Information Company Publication Information and Contributors Alloy Phase Diagrams was published in 1992 as Volume 3 of the ASM Handbook. The Volume was prepared under the direction of the ASM International Alloy Phase Diagram and the Handbook Committees. Foreword Phase diagrams, thermodynamic data in graphical form, are one of the basic tools of the metallurgist, materials scientist, and materials engineer. They can be used for alloy design, selection of hot-working and fabricating parameters, prediction of performance, guidance in selection of hot-working and fabricating parameters, prediction of performance, guidance in selection of heat-treating process parameters, solving performance problems, including failure analysis, and for many other purposes. The formation of The American Society of Steel Treating, the forerunner of ASM International, was based on better understanding of heat-treating technology; this understanding was, of course, rooted in part in the proper utilization of phase diagrams. Experimental tools such as metallography were used in those early days, both to determine phase diagrams and to link the heat-treating process with the desired microstructure. In 1978 ASM International joined with the National Bureau of Standards (now the National Institute of Standards of Technology, or NIST) in an effort to improve the reliability of phase diagrams by evaluating the existing data on a system-by-system basis. ASM raised $4 million from industry and government sources and NIST provided a similar amount of financial and in-kind support for this historic undertaking. An international effort was mounted simultaneously with similar objectives. As a result, all of the important binary systems have been evaluated, and international partners have evaluated more than 2000 ternary systems. ASM actively participates in the Alloy Phase Diagram International Commission (APDIC), which comprises cooperative national or regional committees in 13 countries. APDIC was formed "to set overall objectives, determine priorities for alloy systems to be assessed, coordinate the assessment programs of APDIC members and associate members, establish scope and quality standards for assessment programs in other countries, and assist in the timely dissemination of the resultant phase diagram data." The complete results of the international effort are recorded in various periodical and reference publications. However, we have continued to hear from ASM members that a summary version consisting primarily of phase diagrams should be published as an ASM Handbook for the practicing engineer. While such a Handbook could not contain all the diagrams and data, careful selection would ensure the inclusion of the most important systems, with references to other more complete sources. The present Handbook is the result of our attempts to meet these criteria and the stated need. No reference book of this nature could be published without the contributions of literally hundreds of technical and staff workers. On behalf of ASM International, we extend our sincere thanks and appreciation to the category editors, contributors, reviewers, and staff who worked in this international effort. Thanks are also due to the ASM Alloy Phase Diagram and Handbook Committees for their guidance and support of the project. • Edward H. Kottcamp, Jr. President ASM International • Edward L. Langer Managing Director ASM International Preface Alloy phase diagrams have long been used successfully by the scientific, engineering, and industrial communities as "road maps" to solve a variety of practical problems. It is, thus, not surprising that such diagrams have always been an important part of ASM Handbooks. The previous ASM compilation of commercially important diagrams appeared in Volume 8 of the 8th Edition of Metals Handbook. Shortly after publication of the earlier volume in 1973, recognition of the universal importance of alloy phase diagrams led to the formation of several national phase diagram programs, as well as the International Programme for Alloy Phase Diagrams to act as the coordinating body for these activities. In the U. S., the national program has been spearheaded jointly by ASM International and the National Institute of Standards and Technology. To meet the pressing need for diagrams, the national programs and the entire International Programme had two main goals: to increase the availability of phase diagrams and to ensure that the diagrams made available were of the highest possible quality. The specific tasks that were undertaken to accomplish these goals included assembling all existing data related to alloy phase diagrams, critically evaluating these data, using the data to construct the most up-to-date and accurate diagrams possible, and making the resulting diagrams readily available for use. With the publication of the three-volume set of Binary Alloy Phase Diagrams, Second Edition, by ASM in 1991, the binary alloy portion of this monumental task is virtually complete. In addition, the first-ever truly comprehensive collection of ternary diagrams, the multivolume Handbook of Ternary Alloy Phase Diagrams, is scheduled for publication by ASM in 1994. Information from these two extensive and current diagram sources have been used as the basis of this updated engineering reference book, which reproduces the diagrams of the most commercially important systems (1046 binaries plus 80 ternaries) in a single, convenient volume. These alloy systems are represented by more than 1100 binary diagrams and 313 ternary diagrams, all plotted in weight percent as the primary scale. The binary diagrams reproduced in this Handbook were selected from the 2965 systems covered in Binary Alloy Phase Diagrams, with updated diagrams from literature published since January 1991. Included with the binary diagrams is a complete index of all known alloy phase diagrams from all sources, listing where each can be found should a problem arise concerning a binary system not covered in this Handbook. Although many of the diagrams listed in this index (and a few of those reproduced in this volume) have not been evaluated under the Programmed, they were selected to represent the best available. Updated binary diagrams from the phase diagram update section of the Journal of Phase Equilibria and abstracts of new full-length evaluation from the Journal of Phase Equilibria and the Monograph Series on Alloy Phase Diagrams are available from ASM International on a continuing basis through the Binary Alloy Phase Diagrams Updating Service. The ternary diagrams reproduced here were selected from more than 12,000 diagrams being assembled for the ternary handbook. Where available, diagrams from recently published evaluated compilations were selected. The remainder were selected to represent the best available. To aid in the full and effective use of these diagrams to solve practical problems, we have included an Introduction to Alloy Phase Diagrams, which contains sections on the theory and use of phase diagrams, and an Appendix listing the relevant properties of the elements and their crystal structures. While the work of developing additional data, expanding alloy system coverage, and refining existing diagrams must and will continue, the quality checks built into the programme ensure that the diagrams reproduced here are as accurate and reliable as possible. Credit for this belongs to the conscientious work of all the experts involved in the worldwide Programme, especially Prof. Thaddeus B. Massalski and Dr. Alan A. Prince, who coordinated the evaluation efforts during the period of greatest activity. The Editors General Information Officers and Trustees of ASM International Officers • LAMET UFRGS • Edward H. Kottcamp, Jr. President and Trustee SPS Technologies • John G. Simon Vice President and Trustee General Motors Corporation • William P. Koster Immediate Past President Metcut Research Associates, Inc. • Edward L. Langer Secretary and Managing Director ASM International • Leo G. Thompson Treasurer Lindberg Corporation Trustees • William H. Erickson Canada Centre for Minerals & Energy • Norman A. Gjostein Ford Motor Company • Nicholas C. Jessen, Jr. Martin Marietta Energy Systems, Inc. • E. George Kendall Northrop Aircraft • George Krauss Colorado School of Mines • Gernant E. Maurer Special Metals Corporation • Alton D. Romig, Jr. Sandia National Laboratories • Lyle H. Schwartz National Institute of Standards & Technology (NIST) • Merle L. Thorpe Hobart Tafa Technologies, Inc. Members of the ASM Alloy Phase Diagram Committee (1991-1992) • Michael R. Notis (Chairman 1991-; Member 1988-) Lehigh University • James Brown (1990-) Ontario Hydro • Cathleen M. Cotell (1991-) Naval Research Labs • Charles E. Ells (1991-) Atomic Energy of Canada, Ltd. • Gretchen Kalonji (1991-) University of Washington • Marc H. LaBranche (1991-) DuPont • Vincent C. Marcotte (1987-) IBM East Fishkill Facility • T.B. Massalski (1987-) Carnegie-Mellon University • Sailesh M. Merchant (1990-) AT&T Bell Labs • John E. Morral (1990-) University of Connecticut • Charles A. Parker (1987-) Allied Signal Research & Technology • Alan Prince (1987-) Consultant • Gaylord D. Smith (1987-) Inco Alloys International Inc. • Michael S. Zedalis (1991-) Allied Signal, Inc. Members of the ASM Handbook Committee (1992-1993) • Roger J. Austin (Chairman 1992-; Member 1984-) Hydro-Lift • David V. Neff (Vice-Chairman 1992-; Member 1986-) Metaullics System • Ted Anderson (1991-) Texas A&M University • Bruce Bardes (1992-) GE Aircraft Engines • Robert J. Barnhurst (1988-) Noranda Technology Centre • Toni Brugger (1992-) Phoenix Pipe & Tube Co. • Stephen J. Burden (1989-) GTE Valenite • Craig V. Darragh (1989-) The Timken Company • Russell J. Diefendorf (1990-) Clemson University • Aicha Elshabini-Riad (1990-) Virginia Polytechnic & State University • Gregory A. Fett (1992-) Dana Corporation • Michelle M. Gauthier Raytheon Company • Toni Grobstein (1990-) NASA Lewis Research Center • Susan Housh (1990-) Dow Chemical U.S.A. • Dennis D. Huffman (1982-) The Timken Company • S. Jim Ibarra (1991-) Amoco Research Center • J. Ernesto Indacochea (1987-) University of Illinois at Chicago • Peter W. Lee (1990-) The Timken Company • William L. Mankins (1989-) Inco Alloys International, Inc. • Richard E. Robertson (1990-) University of Michigan • Jogender Singh (1992-) NASA • Jeremy C. St. Pierre (1990-) Hayes Heat Treating Corporation • Ephraim Suhir (1990-) AT&T Bell Laboratories • Kenneth B. Tator (1991-) KTA-Tator, Inc. • Malcolm Thomas (1992-) General Motors Corp. • William B. Young (1991-) Dana Corporation Staff ASM International staff who contributed to the development of the Volume included Hugh Baker, Editor; Hiroaki Okamoto, Senior Technical Editor; Scott D. Henry, Manager of Handbook Development; Grace M. Davidson, Manager, Production Systems; Mary Anne Fleming, Manager, APD Publications; Linda Kacprzak, Manager of Production; Heather F. Lampman, Editorial/Production Assistant; William W. Scott, Jr., Technical Director; Robert C. Uhl, Director of Reference Publications. Editorial Assistance was provided by Nikki D. Wheaton and Kathleen Mills. Production Assistance was provided by Donna Sue Plickert, Steve Starr, Karen Skiba, Patricia Eland, and Jeff Fenstermaker. Conversion to Electronic Files ASM Handbook, Volume 3, Alloy Phase Diagrams was converted to electronic files in 1998. The conversion was based on the First Printing (1992). No substantive changes were made to the content of the Volume, but some minor corrections and clarifications were made as needed. ASM International staff who contributed to the conversion of the Volume included Sally Fahrenholz-Mann, Bonnie Sanders, Marlene Seuffert, Scott Henry, and Robert Braddock. The electronic version was prepared under the direction of William W. Scott, Jr., Technical Director, and Michael J. DeHaemer, Managing Director. Copyright Information (for Print Volume) Copyright © 1992 by ASM International All rights reserved No part of this book may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the written permission of the copyright owner. ASM Handbook is a collective effort involving thousands of technical specialists. It brings together in one book a wealth of information from world-wide sources to help scientists, engineers, and technicians solve current and long-range problems. Great care is taken in the compilation and production of this Volume, but it should be made clear that NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE GIVEN IN CONNECTION WITH THIS PUBLICATION. Although this information is believed to be accurate by ASM, ASM cannot guarantee that favorable results will be obtained from the use of this publication alone. This publication is intended for use by persons having technical skill, at their sole discretion and risk. Since the conditions of product or material use are outside of ASM's control, ASM assumes no liability or obligation in connection with any use of this information. No claim of any kind, whether as to products or information in this publication, and whether or not based on negligence, shall be greater in amount than the purchase price of this product or publication in respect of which damages are claimed. THE REMEDY HEREBY PROVIDED SHALL BE THE EXCLUSIVE AND SOLE REMEDY OR BUYER, AND IN NO EVENT SHALL EITHER PARTY BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES WHETHER OR NOT CAUSED BY OR RESULTING FROM THE NEGLIGENCE OF SUCH PARTY. As with any material, evaluation of the material under end-use conditions prior to specification is essential. Therefore, specific testing under actual conditions is recommended. Nothing contained in this book shall be construed as a grant of any right of manufacture, sale, use, or reproduction, in connection with any method, process, apparatus, product, composition, or system, whether or not covered by letters patent, copyright, or trademark, and nothing contained in this book shall be construed as a defense against any alleged infringement of letters patent, copyright, or trademark, or as a defense against liability for such infringement. Comments, criticisms, and suggestions are invited, and should be forwarded to ASM International. Library of Congress Cataloging-in-Publication Data (for Print Volume) ASM handbook. (Revised for vol. 3) Vols. 1-2 have title: Metals handbook. Includes biographical references and indexes. Contents: v. 1. Properties and selection irons, steels, and high-performance alloys v. 2. Properties and selection nonferrous alloys and special- purpose v. 3. Alloy phase diagrams 1. Metals Handbooks, manuals, etc. I. ASM International. Handbook Committee II. Metals handbook. TA459.M43 1990 620.1'6 90-115 ISBN: 0-87170-377-7 (v.1) 0-87170-381-5 (v.3) SAN: 204-7586 Printed in the United States of America Introduction to Alloy Phase Diagrams Hugh Baker, Editor Introduction ALLOY PHASE DIAGRAMS are useful to metallurgists, materials engineers, and materials scientists in four major areas: (1) development of new alloys for specific applications, (2) fabrication of these alloys into useful configurations, (3) design and control of heat treatment procedures for specific alloys that will produce the required mechanical, physical, and chemical properties, and (4) solving problems that arise with specific alloys in their performance in commercial applications, thus improving product predictability. In all these areas, the use of phase diagrams allows research, development, and production to be done more efficiently and cost effectively. In the area of alloy development, phase diagrams have proved invaluable for tailoring existing alloys to avoid overdesign in current applications, designing improved alloys for existing and new applications, designing special alloys for special applications, and developing alternative alloys or alloys with substitute alloying elements to replace those containing scarce, expensive, hazardous, or "critical" alloying elements. Application of alloy phase diagrams in processing includes their use to select proper parameters for working ingots, blooms, and billets, finding causes and cures for microporosity and cracks in castings and welds, controlling solution heat treating to prevent damage caused by incipient melting, and developing new processing technology. In the area of performance, phase diagrams give an indication of which phases are thermodynamically stable in an alloy and can be expected to be present over a long time when the part is subjected to a particular temperature (e.g., in an automotive exhaust system). Phase diagrams also are consulted when attacking service problems such as pitting and intergranular corrosion, hydrogen damage, and hot corrosion. In a majority of the more widely used commercial alloys, the allowable composition range encompasses only a small portion of the relevant phase diagram. The nonequilibrium conditions that are usually encountered in practice, however, necessitate the knowledge of a much greater portion of the diagram. Therefore, a thorough understanding of alloy phase diagrams in general and their practical use will prove to be of great help to a metallurgist expected to solve problems in any of the areas mentioned above. Common Terms Before the subject of alloy phase diagrams is discussed in detail, several of the commonly used terms will be discussed. Phases. All materials exist in gaseous liquid, or solid form (usually referred to as a phase), depending on the conditions of state. State variables include composition, temperature, pressure, magnetic field, electrostatic field, gravitational field, and so on. The term "phase" refers to that region of space occupied by a physically homogeneous material. However, there are two uses of the term: the strict sense normally used by physical scientists and the somewhat looser sense normally used by materials engineers. In the strictest sense, homogeneous means that the physical properties throughout the region of space occupied by the phase are absolutely identical, and any change in condition of state, no matter how small, will result in a different phase. For example, a sample of solid metal with an apparently homogeneous appearance is not truly a single-phase material, because the pressure condition varies in the sample due to its own weight in the gravitational field. In a phase diagram, however, each single-phase field (phase fields are discussed in a following section) is usually given a single label, and engineers often find it convenient to use this label to refer to all the materials lying within the field, regardless of how much the physical properties of the materials continuously change from one part of the field to another. This means that in engineering practice, the distinction between the terms "phase" and "phase field" is seldom made, and all materials having the same phase name are referred to as the same phase. Equilibrium. There are three types of equilibia: stable, metastable, and unstable. These three conditions are illustrated in a mechanical sense in Fig. 1. Stable equilibrium exists when the object is in its lowest energy condition; metastable equilibrium exists when additional energy must be introduced before the object can reach true stability; unstable equilibrium exists when no additional energy is needed before reaching metastability or stability. Although true stable equilibrium conditions seldom exist in metal objects, the study of equilibrium systems is extremely valuable, because it constitutes a limiting condition from which actual conditions can be estimated. Fig. 1 Mechanical equilibria: (a) Stable. (b) Metastable. (c) Unstable Polymorphism. The structure of solid elements and compounds under stable equilibrium conditions is crystalline, and the crystal structure of each is unique. Some elements and compounds, however, are polymorphic (multishaped); that is, their structure transforms from one crystal structure to another with changes in temperature and pressure, each unique structure constituting a distinctively separate phase. The term allotropy (existing in another form) is usually used to describe polymorphic changes in chemical elements. Crystal structure of metals and alloys is discussed in a later section of this Introduction; the allotropic transformations of the elements are listed in the Appendix to this Volume. Metastable Phases. Under some conditions, metastable crystal structures can form instead of stable structures. Rapid freezing is a common method of producing metastable structures, but some (such as Fe 3 C, or "cementite") are produced at moderately slow cooling rates. With extremely rapid freezing, even thermodynamically unstable structures (such as amorphous metal "glasses") can be produced. Systems. A physical system consists of a substance (or a group of substances) that is isolated from its surroundings, a concept used to facilitate study of the effects of conditions of state. "Isolated" means that there is no interchange of mass between the substance and its surroundings. The substances in alloy systems, for example, might be two metals, such as copper and zinc; a metal and a nonmetal, such as iron and carbon; a metal and an intermetallic compound, such as iron and cementite; or several metals, such as aluminum, magnesium, and manganese. These substances constitute the components comprising the system and should not be confused with the various phases found within the system. A system, however, also can consist of a single component, such as an element or compound. Phase Diagrams. In order to record and visualize the results of studying the effects of state variables on a system, diagrams were devised to show the relationships between the various phases that appear within the system under equilibrium conditions. As such, the diagrams are variously called constitutional diagrams, equilibrium diagrams, or phase diagrams. A single-component phase diagram can be simply a one- or two-dimensional plot showing the phase changes in the substance as temperature and/or pressure change. Most diagrams, however, are two- or three-dimensional plots describing the phase relationships in systems made up of two or more components, and these usually contain fields (areas) consisting of mixed-phase fields, as well as single-phase fields. The plotting schemes in common use are described in greater detail in subsequent sections of this Introduction. System Components. Phase diagrams and the systems they describe are often classified and named for the number (in Latin) of components in the system: Number of components Name of system or diagram One Unary Two Binary Three Temary Four Quaternary Five Quinary Six Sexinary Seven Septenary Eight Octanary Nine Nonary Ten Decinary Phase Rule. The phase rule, first announced by J. William Gibbs in 1876, related the physical state of a mixture to the number of constituents in the system and to its conditions. It was also Gibbs who first called each homogeneous region in a system by the term "phase." When pressure and temperature are the state variables, the rule can be written as follows: f = c - p + 2 where f is the number of independent variables (called degrees of freedom), c is the number of components, and p is the number of stable phases in the system. Unary Diagrams Invariant Equilibrium. According to the phase rule, three phases can exist in stable equilibrium only at a single point on a unary diagram (f = 1 - 3 + 2 = 0). This limitation is illustrated as point O in the hypothetical unary pressure- temperature (PT) diagram shown in Fig. 2. In this diagram, the three states (or phases) solid, liquid, and gas are represented by the three correspondingly labeled fields. Stable equilibrium between any two phases occurs along their mutual boundary, and invariant equilibrium among all three phases occurs at the so-called triple point, O, where the three boundaries intersect. This point also is called an invariant point because, at that location on the diagram, all externally controllable factors are fixed (no degrees of freedom). At this point, all three states (phases) are in equilibrium, but any changes in pressure and/or temperature will cause one or two of the states (phases) to disappear. Fig. 2 Schematic pressure-temperature phase diagram Univariant Equilibrium The phase rule says that stable equilibrium between two phases in a unary system allows one degree of freedom (f = 1 - 2 + 2). This condition, called univariant equilibrium or monovariant equilibrium, is illustrated as line 1, 2, and 3 separating the single-phase fields in Fig. 2. Either pressure or temperature may be freely selected, but not both. Once a pressure is selected, there is only one temperature that will satisfy equilibrium conditions, and conversely. The three curves that issue from the triple point are called triple curves: line 1, representing the reaction between the solid and the gas phases, is the sublimation curve; line 2 is the melting curve; and line 3 is the vaporization curve. The vaporization curve ends at point 4, called a critical point, where the physical distinction between the liquid and gas phase disappears. Bivariant Equilibrium. If both the pressure and temperature in a unary system are freely and arbitrarily selected, the situation corresponds to having two degrees of freedom, and the phase rule says that only one phase can exit in stable equilibrium (p = 1 - 2 + 2). This situation is called bivariant equilibrium. Binary Diagrams If the system being considered comprises two components, a composition axis must be added to the PT plot, requiring construction of a three-dimensional graph. Most metallurgical problems, however, are concerned only with a fixed pressure of one atmosphere, and the graph reduces to a two-dimensional plot of temperature and composition (TX diagram). The Gibbs phase rule applies to all states of matter (solid, liquid, and gaseous), but when the effect of pressure is constant, the rule reduces to: f = c - p + 1 The stable equilibria for binary systems are summarized as follows: Number of components Number of phases Degrees of freedom Equilibrium 2 3 0 Invariant 2 2 1 Univariant 2 1 2 Bivariant Miscible Solids. Many systems are comprised of components having the same crystal structure, and the components of some of these systems are completely miscible (completely soluble in each other) in the solid form, thus forming a continuous solid solution. When this occurs in a binary system, the phase diagram usually has the general appearance of that shown in Fig. 3. The diagram consists of two single-phase fields separated by a two-phase field. The boundary between the liquid field and the two-phase field in Fig. 3 is called the liquidus; that between the two-phase field and the solid field is the solidus. In general, a liquidus is the locus of points in a phase diagram representing the temperatures at which alloys of the various compositing of the system begin to freeze on cooling or finish melting on heating; a solidus is the locus of points representing the temperatures at which the various alloys finish freezing on cooling or begin melting on heating. The phases in equilibrium across the two-phase field in Fig. 3 (the liquid and solid solutions) are called conjugate phases. Fig. 3 Schematic binary phase diagram showing miscibility in both the liquid and solid states [...]... Fig 2, ∆V is the difference in molar volume of the two phases in the reaction, and ∆H is the difference in molar enthalpy of the two phases (the heat of the reaction) Solutions The shapes of liquidus, solidus, and solvus curves (or surfaces) in a phase diagram are determined by the Gibbs energies of the relevant phases In this instance, the Gibbs energy must include not only the energy of the constituent... process, the change in Gibbs energy is less than zero (negative); that is, the Gibbs energy decreases during the process, and it reaches a minimum at equilibrium Features of Phase Diagrams The areas (fields) in a phase diagram, and the position and shapes of the points, lines, surfaces, and intersections in it, are controlled by thermodynamic principles and the thermodynamic properties of all of the phases... appears in the liquidus and solidus curves Mixtures The two -phase field in Fig 13( f) consists of a mixture of liquid and solid phases As stated above, the compositions of the two phases in equilibrium at temperature T3 are C1 and C2 The horizontal isothermal line connecting points 1 and 2, where these compositions intersect temperature T3, is called a tie line Similar tie lines connect the coexisting phases... A Prince, Alloy Phase Equilibria, Elsevier, 1966 This out-of-print book covers the thermodynamic approach to binary, ternary, and quaternary phase diagrams 5 68Gor: P Gordon, Principles of Phase Diagrams in Materials Systems, McGraw-Hill 1968; reprinted by Robert E Krieger Publishing, 19 83 Covers the thermodynamic basis of phase diagrams; the presentation is aimed at materials engineers and scientists... J.W Cahn, and L.H Bennett, The Centennial of the Gibbs-Konovalov Rule for Congruent Points, Bull Alloy Phase Diagrams, Vol 2 (No 1), 1981, p 29 -34 Presents the theoretical basis for the rule and its application to phase diagram evaluation 18 91Oka1: H Okamoto and T.B Massalski, Thermodynamically Improbable Phase Diagrams, J Phase Equilibria, Vol 12 (No 2), 1991, p 148-168 Presents examples of phase- rule... abrupt change in the composition dependence of the thermodynamic properties of the single phase involved (in this instance, the δ phase) It cannot be explained by any possible abrupt change in the temperature dependence of the Gibbs energy function of the phase (If the temperature dependence were involved, there would also be a change in the boundary of the ε phase. ) Problems Connected With Phase- Boundary... metallurgy Thermodynamic Principles The reactions between components, the phases formed in a system, and the shape of the resulting phase diagram can be explained and understood through knowledge of the principles, laws, and terms of thermodynamic, and how they apply to the system Internal Energy The sum of the kinetic energy (energy of motion) and potential energy (stored energy) of a system is called its internal... indicate the limits of solubility of component B in A and A in B, respectively The configurations of these and all other phase diagrams depend on the thermodynamics of the system, as discussed later in this Introduction Fig 4 Schematic binary phase diagrams with solid-state miscibility where the liquidus shows a maximum (a) and a minimum (b) Fig 5 Schematic binary phase diagram with a minimum in the liquidus... components, A and B The result is a series of plots similar to those shown in Fig 13( a) to (e) Fig 13 Use of Gibbs energy curves to construct a binary phase diagram that shows miscibility in both the liquid and solid states Source: Adapted from 66Pri 4 At temperature T1, the liquid solution has the lower Gibbs energy and, therefore, is the more stable phase At T2, the melting temperature of A, the liquid and. .. At temperature T3, between the melting temperatures of A and B, the Gibbs energy curves cross Temperature T4 is the melting temperature of B, while T5 is below it Construction of the two -phase liquid-plus-solid field of the phase diagram in Fig 13( f) is as follows According to thermodynamic principles, the compositions of the two phases in equilibrium with each other at temperature T3 can be determined . The Materials Information Company Publication Information and Contributors Alloy Phase Diagrams was published in 1992 as Volume 3 of the ASM Handbook. The Volume was prepared under the. Alloy Phase Diagrams, which contains sections on the theory and use of phase diagrams, and an Appendix listing the relevant properties of the elements and their crystal structures. While the. single -phase fields separated by a two -phase field. The boundary between the liquid field and the two -phase field in Fig. 3 is called the liquidus; that between the two -phase field and the solid