Cutting Tool Materials docx

1 Cutting Tool Materials ‘What is the use of a book’ , thought Alice, ‘without pictures or conversations?’   (1832–1898) [Alice in Wonderland, Chap. 1] Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com 1.1 Cutting Technology – an Introduction Previously, many of the unenlightened manufactur- ing companies, having purchased an expensive and sophisticated new machine tool, considered cutting tool technology as very much an aerthought and sup- plied little nancial support, or technical expertise to purchase these tools. Today, tooling-related technolo- gies are treated extremely seriously, as it is here that optimum production output, consistency of machined product and value-added activities are realised. Of- ten companies feel that to increase productivity – to oset the high capital investment in the plant and to amortise such costs (i.e. pay-back), is the most advan- tageous way forward. is strategy can create ‘bottle- necks’ and disrupt the harmonious ow of production at later stages within the manufacturing environment. Another approach might be to maximise the number of components per hour, or alternatively, drive down costs at the expense of shorter tool life, which would increase the non-productive idle time for the produc- tion set-up. Here, the prime 1 tooling factor should not be for just a marginal increase in productivity and eciency, nor the perfection of any particular opera- tion. If ‘bottlenecks’ in component production occur, they can readily be established by piles of machined parts sitting on the shop oor awaiting further valued- added activities to be undertaken. ese ‘line-balance’ production problems need to be addressed by achiev- ing improved productivity across the whole operation, perhaps by the introduction of a Taguchi-type com- ponent ow analysis system within the manufactur- ing facility. e well-known phrase that: ‘No machine is an island’ (i.e. for part production) and that manu- facturing should be thought of as ‘One big harmonious machine’ and not a lot of independent problems, will create a means by which increases in productivity can be achieved. e cutting tool problems, such as: too wide a range of tooling inventory, inappropriate tools/out-dated tooling, or not enough tools for the overall operational 1 Tooling refers not only to non-consumable items such as: cut- ting tools and inserts, tool holders, tool presetters, screws, washers and spacers, screwdrivers/Allen keys, tool handling equipment, but also consumable items, such as hand wipes, grease/oils employed in tool kitting and cutting uids, etc. requirements for a specic manufacturing environ- ment, can be initially addressed by employing the fol- lowing tooling-related philosophy – having recently undertaken a survey of the current status of tooling within the whole company: • Rationalisation • Consolidation • Optimisation NB ese three essential tool-related factors in es- tablishing the optimum tooling requirements for the current production needs, will be briey re- viewed. .. Rationalisation In order to be able to rationalise the tools within the current production facility, it is essential to conduct a thorough appraisal of all the tools and associated equipment with the company. is tooling exercise will be both time-consuming and costly, because it necessitates a considerable manpower resource and needs a means of identifying all the tools and inserts currently utilised, in some logical and tabulated man- ner. Such surveys are oen best conducted by utilis- ing a primitive but ecient tool-card indexing system in the rst instance. Details, such as: tool type and its tooling manufacturer, quantity of tools in use and the current levels of stock in the tool store, their current location(s), feeds and speeds utilised, together with any other relevant tool-related details are indexed on such cards. Once these tooling facts have been estab- lished, then they can be loaded into either a comput- erized tool management system database, or recorded onto an uncomplicated tooling database for later in- terrogation. Having established the current status of the tool- ing within the manufacturing facility, this allows for a tooling rationalisation campaign to be developed. Tool rationalisation (Fig. 1) consists of looking at the results of the previous tooling survey and signicantly reducing the number of tooling suppliers for particular types of tools and inserts. is initial rationalisation policy has the twin benets of minimising tooling sup- pliers with their distinct varieties of tools, while en- abling bulk purchase of such tools from the remaining suppliers, at preferential nancial rates of purchase. Moreover, by using less tooling companies whilst pur- chasing bulk stock, this has the bonus of making you one of their prime customers with their undivided at-  Chapter  Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com Figure 1. Rationalisation of cutting inserts, can have a dramatic eect on reducing the tooling and workholding inventory. [Courtesy of Sandvik Coromant] . Cutting Tool Materials  Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com tention, should the need for later ‘tool problem-solv- ing’ of manufacturing clichés in production occur. .. Consolidation For any tooling that remains aer the rationalisation exercise, these should be consolidated, by reducing the number of insert grades, by at least half – which oen proves to have little eect on production capability. By grouping inserts by their respective sizes, shapes and say, nose radius for example, this will eliminate many of the less-utilised inserts, enabling the poten- tial for bulk purchase from the tooling supplier, with an attendant reduction in tool costs. From this con- solidation activity, it may now be possible to purchase higher-performance grade cutting inserts, that meet a wider application range, enabling the consolidation to be even more eective. Furthermore, such improved inserts, will probably have a longer tool life and can be utilised at higher speeds, which probably negates their extra cost, over the previously used inserts. If fewer grades of insert are stocked, the tooling/application engineers will be acquainted with them much more thoroughly and this will result in a added eectiveness and a consistent application, for the production of ma- chined components – more will be said on this latter point in the next section on Optimisation. .. Optimisation By consolidating the tooling, it allows productivity to be boosted by optimisation of the cutting insert grades. For example, in turning operations, the depth of cut can probably maximised and, as a result, the number of passes along, or across the part can be mi- nimised. It can be argued that increasing the depth of cut leads to a reduction in the subsequent tool life (in terms of minutes of cutting per edge). However, there are fewer cuts per part, so each machined workpiece requires less overall cutting and as a result, many more parts per edge can be produced. More important, are that the cycle times for roughing operations be re- duced: a reduction in the number of roughing passes from three to one, results in a 66% reduction in the cycle time. is increase in productivity may justify any potential decrease in tool life, on the basis that it could reduce, or eliminate a potential ‘bottleneck’ in latter production processes of the part’s manufacture. To extract the maximum productivity from today’s high-performance grades, they must be worked hard and pushed to their fullest capabilities. When tool life is reduced by increasing the depth of cut, there are several ways that a such loss can be minimised. For example, it is known that the size of the insert’s nose radius has a pronounced eect on tool life, so by doubling the depth of cut this can, in the main, allow for a larger nose radius – assuming that the component feature allows access. If an increase in nose radius cannot be utilised, then increasing the insert’s size will help to oset any higher wear rates, by providing a better heat dissipation for the action of cutting. e accepted turning practice when roughing- out, is that no more than half the insert’s cutting edge length should be utilised, because as the depth of cut approaches this value, a larger insert is recommended. Where large depths of cut are used in combination with high feedrates, a roughing grade insert geometry promotes longer tool life, than a general-purpose in- sert. Oen, by using a single-sided insert rather than a double-sided one for roughing cuts, this has the twin benets of increased productivity and longer tool life (in terms of machined parts per edge). Normally, single-sided inserts are recommended whenever the depth of cut and feedrate are so high that the surface speed must be reduced below the grade’s normal range, in order to maintain an adequate tool life. Such inserts should be considered if erratic insert breakage occurs. Later to be discussed in the chapter on Machin- ability and Surface Integrity, is the fact that the highest temperature region on the tool’s rake face is not at the cutting edge; but in the vicinity on the chip/tool inter- face where chip curling occurs – this is some distance back and where the crater is formed. e position for this highest isothermal region can vary, depending upon the feedrate. For example, if the feedrate is in- creased, the highest temperature zone on the insert’s face will move away from the cutting edge; conversely, if the feedrate is now reduced, this region moves to- ward the cutting edge. is phemomena means that if the feedrate is too low for the chosen insert geom- etry and edge preparation, heat will be concentrated too near the cutting edge and insert wear will be ac- celerated. us, by increasing the feedrate, it has the aect of moving the maximum heat zone away from the insert’s edge and is so doing, extends tool life – in terms of minutes of actual cut-time per edge. As a re- sult, each machined part will be produced in less time and at higher feeds, so the tool life in terms of parts per edge will also increase.  Chapter  Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com As a result of the inappropriate use of cutting data, such as incorrect feedrates employed for the chosen in- sert geometry, this can produce a number of undesir- able symptoms. ese symptomatic problems include: extremely shortened tool life, edge chipping and insert breakage are likely if feedrates are too high, whereas when feeds are too low, chip control becomes a prob- lem. Once the insert grades have been consolidated with their associated geometries, it is relatively easy to determine the feedrates for a selected grade of work- piece materials. Tooling suppliers can recommend a potential insert grade for particular component part material, with an initial selection of insert grade, such surface speeds being indicated in the Appendix. ese inserts can be optimised by ‘juggling’ the grades and geometries marginally around the specied values, this may allow feedrates to be increased and should provide a signicant pay-o in terms of improved productivity, at little, or no additional capital expenditure. If the cutting speed is increased rather than the feed, a point is reached where any increase in surface speed will result in a decrease in productivity. In other words, cutting too fast will mean spending more time changing tools than making parts! Equally, by cutting too slowly, the tool will last much longer, but this is at the expense of the number of machined parts pro- duced per shi. If these statements are correct, what is the ‘right’ surface speed? is question will now be discussed more fully. If we return to the theme previously mentioned, namely: ‘No machine is an island’ and treat the pro- duction shop as: ‘One big machine’ , it can be stated that every shop should determine its own particular manufacturing objectives – when considering both cutting speeds and tool life. Typical objectives for tool life might be the completion of a certain number of parts before indexing the insert, or adopting a ‘sister tool’ 2 , or alternatively, insert indexing aer one/part of a shi. If very expensive components are being ma- chined, the main goal is to avoid catastrophic insert 2 ‘Sister tooling’ is the term that refers to a duplicate tool (i.e. having the same tool osets) held in the turret/magazine and can be automatically indexed to this tool, to minimise down-time when changing tools. Such a ‘sister tool’ , can be pre-programmed into the CNC controller of the machine tool, to either change aer a certain number of parts has been produced, or if the tool life has been calculated, then when the feed function on the CNC has decremented down to this preset value, then the ‘sister tool’ is selected. failure, which on a nishing cut, would probably result in scrapping the part. When exceedingly large parts are to be machined, the objective may simply be to complete just one part per insert, or in an even more extreme situation, just one pass over the part. When small parts are being produced, then the tool life can be controlled in order to minimise dimensional size variation with in-cut time. is strategy of tool life con- trol, reduces the need for frequent adjustment of tool oset compensations in the CNC controller. However, one idea shared by all of these strategic production ap- proaches, is that by optimising the surface speed, the manufacturing objectives will be realised. As a con- sequence of this approach to production, there is no correct surface speed for any specic combination of material and insert grade, the optimum surface speed depends upon the company’s manufacturing require- ments at this time. When long production runs occur, these are ideal because it allows cutting data experimentation to dis- cover the optimum speed for a particular production cycle. Sometimes it is not possible to nd the speed to exactly meet the production demands and, a change of insert grades, to one of the higher-technology materi- als may be in order. If short production runs are neces- sary, this can oen rule out any experimentation with insert grades, but by consultation with a ‘cutting tool expert’ , or reference to the published cutting literature the answer may be found to the problem of insert op- timisation. However a cautionary note, care must be taken when utilising published recommendations, as they should only be employed as guidelines, to help initiate the job into production. Comparison with a known starting point within the recommended range for specic production con- ditions, namely for: large depths of cut, high feedrates, very long continuous cuts, signicant interrupted cuts, workpiece surface scale and the absence of cool- ant, would all suggest that reductions in surface speed should be initially considered. Conversely, production conditions that result in: short lengths of cut, shallow depths of cut, low feedrates, smooth uninterrupted cuts, clean pre-turned, or bright-drawn wrought workpiece materials and ood coolant, having a very rigid setup, suggests that the recommended ranges for the insert could be exceeded, while still maintaining an acceptable tool life. It should be remembered that the main requirement is for an overall increase in production output and not perfection. Aer the analysis, when the tooling inven- tory has been consolidated, there will be fewer and Cutting Tool Materials  Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com more versatile insert grades and geometries that need to be considered. is smaller insert inventory allows a detailed appreciation of how to optimise the speeds and feeds in combination with depths of cut more ef- fectively, for the desired production objectives. By op- timisation here of the machining parameters, this al- lows full utilisation of the capital equipment, with the result that large improvements in overall manufactur- ing eciency can be expected. It is evident from this discussion concerning opti- misation, that the parameters of: tool life, feedrate and cutting speed form a complex relationship, which is il- lustrated in Fig. 2a. Consequently, if you change one parameter, it will aect the others, so a compromise has to be reached to obtain the optimum performance from a cutting tool. Preferably, the ideal cutting tool should have superior performance if ve distinct areas (see Fig. 2b): • Hot hardness – is necessary in order to maintain sharp and consistent cutting edge at the elevated temperatures that are present when machining. NB If the hot hardness of the tooling is not su- cient for the temperature generated at the tool’s tip, then it will degrade quickly and be useless. • Resistance to thermal shock – this is necessary in order to overcome the eects of the continuous cycle of heating and cooling that is typical in a mill- ing operation, or when an intermittent cutting op- eration occurs on a lathe (e.g. an eccentric turning operation). NB If this thermal shock resistance is too low, then rapid wear rates can be expected, typied in the past, by ‘comb cracks’ on High-speed steel (HSS) milling cutters. • Lack of anity – this condition should be present between the tool and the workpiece, since any de- gree of anity will lead to the formation of a built- up edge (BUE) – see the chapter on Machinability and Surface Integrity. NB is BUE will modify the tool geometry, lead- ing to poorer chip-breaking ability, with higher forces generated, leading to degraded workpiece surface nish. Ideally, the cutting edge should be inert to any reaction with the workpiece. Figure 2. The main factors aecting cutting tool life, under ‘steady-state’ cutting conditions .  Chapter  Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com • Resistance to oxidation – a cutting edge should have the desirable condition of having a high resis- tance to oxidation. NB is oxidation resistance of the cutting tool is necessary, in order to reduce the debilitating wear that oxidation can produce when machining at el- evated temperatures. • Toughness – allows the cutting edge of the insert to absorb the cutting forces and shock loads produced whilst machining, particularly relevant when inter- mittent cutting operations occur. NB If an insert is not suciently tough, then when unwanted vibrations are induced, this can result in either premature failure, or worse, a shattered cut- ting edge. Cutting tool manufacturers, by careful balancing of these ve factors for the ideal cutting tool, can produce grades of inserts which distinctly vary, allowing a wide range of workpiece materials to be machined through the selection of the correct insert grade for a particular material. In recent years, tooling manufacturers have produced wider ranges of workpiece-cutting ability from fewer types of inserts, across a diverse range of speeds and feeds, allowing tooling inventories to be reduced even further. is brief introduction showing how and in what manner correct tooling can be used to increase production output, needs to be considered against the current situation of advances in cutting tool materials and their selection – this will be the theme of the next section. 1.2 The Evolution of Cutting Tool Materials .. Plain Carbon Steels Prior to 1870, all turning tooling materials were pro- duced from plain carbon steels, with a typical compo- sition of 1% carbon and 0.2% manganese – the remain- der being iron. Such a tool steel composition meant that it had a low ‘hot-hardness’ (i.e, its ability to retain a cutting edge at elevated temperatures), as such, the cutting edge broke down at temperatures approaching 250°C, this in reality kept cutting speeds to approxi- mately 5 m·min –1 . ese early cutting tools frequently had quench cracks present which severely weakened the cutting edge, as a result of water hardening at quenching rates greater than 1000°C/second (i.e. nec- essary to exceed the critical cooling velocity – to fully harden the steel), upon manufacture. By 1870, Mushet (working in England), had introduced a more com- plex steel composition, containing: 2% carbon, 1.6% manganese, 5.5% Tungsten and 0.4% chromium, with the remainder being iron. e advantage of this newly developed steel was that it could be air-hardened, this was a signicantly less drastic quench than using a water quenchant. Mushet’s steel had greater ‘hot- hardness’ and could be utilised at cutting speeds up to 8 m·min –1 . is turning tool material composition, was retained until around 1900, but with the level of chromium gradually superseding that of manganese. .. High-Speed Steels Around the turn of the century in the United States, fundamental metallurgical work was being undertaken by F.W. Taylor and his associate M. White and by 1901, these researchers had greatly improved the overall tool steel and slightly modifying its composition with a material that was to be known as High-speed steel (HSS), enabling cutting speeds to approach 19 m·min –1 . High-speed steel was not a new material, but basically an innovative heat treatment procedure. e typical metallurgical composition of HSS was: 1.9% carbon, 0.3% manganese, 8% tungsten, and 3.8% chromium, with iron the remainder. Taylor and White’s tool steel mainly diered from that of Mushet’s by an increased amount of tungsten and a further replacement of man- ganese by chromium. By 1904, the content of carbon had been reduced, allowing for more ease in forging this HSS. Further rapid development of the HSS oc- curred over the next ten years, with tungsten content increased to improve its ‘hot-hardness’. Around this time, Dr J.A. Matthews found that vanadium additions had improved the material’s abrasion resistance. By 1910, the content of tungsten had increased to 18%, with 4% chromium and 1% vanadium, hence the well- known 18:4:1 HSS had arrived, its metallurgical com- position continued with only marginal modications over the next 40 years. Of the modications to HSS during this time, of note was that in 1923 the so-called ‘super’ HSS was developed, although this variant did not become commercially viable until 1939, when Gill reduced the tungsten content to enable the tool steel Cutting Tool Materials  Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com to be successfully hot-worked. Around 1950 in the United States, M2 HSS was introduced, having some of the tungsten content replaced by that of molybde- num. is gave the approximate M2 HSS metallurgi- cal composition as: 0.8% C, 4% Cr, 2% V, 6% W and 5% Mo – Fe being the remainder. In this form, the M2 HSS could withstand machining temperatures of up to 650°C (ie the cutter glowing dull red) and still maintain a cutting edge. In 1970, Powder Metallurgy (P/M) by metallurgical processing via hot isostatic pressing (HIP), was intro- duced for the production of HSS, with careful control of elemental particle size; aerward the sintered prod- uct is forged then hot-rolled. is HSS (HIP) process- ing gave a uniformly distributed elemental matrix, overcoming the potential segregation and resulting non-homogenous structure that would normally oc- cur when ingot-style HSS forging. Such P/M process- ing techniques enable the steel-making company to ‘tailor’ and specify the exact metallurgical composition of alloying elements, this would allow the newly-de- veloped sintered/forged HSS tooling to approach that of the performance of cemented carbides, in terms of inherent wear resistance, hardness and toughness. In Fig. 3, a comparison of just some of the tooling materi- als is highlighted, here, fracture toughness is plotted against hardness to indicate the range of inuence of each tool material and the comparative relative mer- its of one material against another, with some of their physical and mechanical properties tabulated in Fig. 3b. A typical sintered micro-grained HSS of today, might contain: 13% W, 10% Co, 6% V, 4.75% Cr and 2.15% C – Fe the remainder. One reason for the ‘keen’ cutting edge that can be retained by sintered micro- grained HSS, is that during P/M processing the rapid atomisation of the particles produces extremely ne carbides of between 1 to 3 µm in diameter – which fully support the cutting edge, whereas HSS produced from an ingot, has carbides up to 40 µm in diameter. By way of illustration of the benets of the latest mi- cro-grained HSS – in the uncoated condition – when compared to its metallurgical competitor of cemented carbide, HSS has a bend, or universal tensile strength of between 2,500 to 6,000 MPa – this being dependent on metallurgical composition, whereas cemented car- bide tooling has a bend strength of between 1,250 to 2,250 MPa. ese metallurgical tool processing tech - niques have signicantly improved sintered micro- grained HSS enabling for example, high-performance drilling, reaming and tapping to be realised. Coating by either single-, or multiple-coating has been shown to signicantly enhance any tooling mate- rial, but this is a complex subject and more will be said on this subject shortly. .. Cemented Carbide Possibly the widest utilised cutting tool materials today are the cemented carbide family of tooling, of which the group derived from tungsten carbide is most read- ily employed. Prior to discussing the physical metal- lurgy and expected mechanical/physical characteris- tics of cemented carbides, it is worth looking into the complex task of insert selection. In Fig. 4, just a small range of the material types, grades, shapes of inserts and coatings by a leading cutting tool company is depicted. Highlighting the complex chip-breaker geometries, necessary to both develop and break chips and evacuate them eciently from the workpiece’s surface region. To give a sim- plied impression of just some of the tooling insert variations and permutations available from a typical tooling manufacturer, if 10 insert grades are listed, in 6 dierent shapes, with 12 diering chip breakers and ve nose radii in the tooling catalogue, this equates to 10 × 6 × 12 × 5, or 3,600 inserts. In reality, there are a number of other important features that could extend this cutting insert permutation to well over ve signi- cant gures – for potential insert selection. When the permutated insert number reaches this level of com- plexity, selecting the optimum combination of insert characteristics becomes more a matter of luck than skill. Tungsten (synonym Wolfram, hence the chemical symbol W), is the heaviest metal in the group VIB in Mendeleev’s Period Chart (i.e. atomic number 74). It was named aer the German word wolfram – from the mineral wolframite – as it was derived from the term wolf rahm, because the ore was said to interfere with tin smelting – supposedly devouring the tin. Whereas the term tungsten, was coined from the Swedish tung sten, meaning heavy stone. Hence, in 1923, the Ger- man inventor K. Schröter produced the rst metal ma- trix composite, known today as cemented carbides. In these rst cemented carbides, Schröter combined tung- sten monocarbide (WC) particles embedding them in a cobalt matrix – these particles acted as a very strong binder. Cemented carbide is a hard transition metal carbide ranging from 60% to 95% bonded to cobalt, this being a more ductile metal. e carbides vary, ranging from having hexagonal structures, to a solid solution of titanium, tantalum and niobium carbides to that of a NaCl structure. Tungsten carbide does not dissolve  Chapter  Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com any transition metals, but it can melt those carbides found in solid solution. Powder metallurgy processing route – liquid-phase sintering – is utilised to produce cemented carbides, as melting only occurs at very high temperatures and there is a means of reducing tung- sten powder using hydrogen from chemically puried ore. Ore reduction can be achieved by the manipula- tion of the processing conditions, enabling the grain size to be controlled/modied as necessary. e uni- form grain sizes of tungsten carbide today can range Figure 3. Cutting tool materials – toughness versus hardness – and their typical material characteristics. [Courtesy of Mitsubishi Carbide] . Cutting Tool Materials  Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com from 0.2 to 7 µm – enabling a nal sintered product to be carefully controlled. Moreover, by additions of ne cobalt at a further processing stage, then wet milling the constituents, allows for precise and uniform con- trol of the grain size – producing a ne powder. Prior to sintering, the milled powder can be spray-dried giv- ing a free-owing spherical powder aggregate, with the addition of lubricant to aid in its consolidation (i.e. pressing into a ‘green compact’). Sintering nor- mally occurs at temperatures of 1500°C in a vacuum, which reduces the porosity from about 50% that is in the ‘green state’ , to less than 0.01% porosity by volume in the nal cutting insert condition. e low level of porosity in the nal product is the result of ‘wetting’ by the liquid present upon sintering. e extent of this ‘wetting’ during liquid-phase sintering, being depen- dent upon molten binder metal dissolving to produce a pore-free cutting insert, this has excellent cohesion between the binder and the hard particles (see Fig. 5, for typical cemented carbide powders and resulting microstructures). It should be stated that most of the ‘iron-group’ of metals can be ‘wetted’ by tungsten car- bide, forming sintered cemented carbide with excel- lent mechanical integrity. Figure 4. Cutting inserts indicating the diverse range of: shapes, sizes and geometries available, with compositions varying from: cemented carbide, ceramics, cermets, to cubic boron nitride deriva- tives. [Courtesy of Sandvik Coromant] .  Chapter  Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com [...]... Raymond, M.K Coatings Keep Cutting Tools Sharp American Machinist, 40–42, May 1996 Richter, A Raising Al – AlTiN Coatings Cutting Tool Engg., 42–46, Jan., 2003 Richter, A Top Coat Cutting Tool Engg., 36–41, Dec., 2003 Sanders, E.H Understanding Coated Carbides Cutting Tool Engg 3–7, Sept./Oct., 1977 Sprout, W PVD Today Cutting Tool Engg., 52–4057, Feb., 1994 Taylor, F.W On the Art of Cutting Metals Trans... A Progress Report on Cutting Tool Materials American Machinist, 39–40, Dec., 1992 Jindal, P.C et al., PVD Coatings for Turning, Cutting Tool Engg., 42–52, Feb., 1999 Kennedy, B Making the Grade – PCBN Applications Cutting Tool Engg., 22–30, June 2002 Lewis, B Fast Times in HSS Cutting Tool Engg., 28–32, July 2001 Lewis, B Confidence Game – Grades and Geometries Cutting Tool Engg., 46–52, Dec., 2002... Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com Figure 12.  Ultra-hard cutting tool materials – cubic boron nitride (CBN) [Courtesy of DeBeers – element 6] Cutting Tool Materials 25 Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com Table 1.  Cutting tool materials – with some important physical properties Black ceramic (Al2O3 + TiC) Cemented carbide... 31–350, 1907 Thalmann, R Cracking the Code – Carbide Classifications Cutting Tool Engg., 34–43, June 1995 Vasilash, G.S The Superfard Coatings: More than Meets the Eye 52–54, Production, Dec., 1995 Weiner, M Coatings Move Forward Cutting Tool Engg., 22–29, Feb., 1999 Woods, S Coat, Please Cutting Tool Engg., 50–56, Oct., 2004 Cutting Tool Materials 31 Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com... handling References Journal and Conference Papers Boller, R Crystal Clear – DLCoatings Cutting Tool Engg., 36–40, May 2002 Craig, P Behind the Carbide Curtain Cutting Tool Engg., 26–41, Aug., 1997 Dzierwa, R Slippery when Blue – Coatings Cutting Tool Engg., 36–41, Jan., 2003 Eastman, M Inserts Show their True Colors Cutting Tool Engg., 30–36, April 1999 Feir, M Post-treatment of PM Parts Metal Powder Report,... Cutting Tool Engg., 46–52, Dec., 2002 Mielert, W Coating for Speed Cutting Tool Engg., 40–44, Feb., 1996 Mirchandani, P.K Making a Better Grade – Composite Carbide Substrates Cutting Tool Engg., 58–61, Jan., 2005 Mitoraj, L The Coating Edge Cutting Tool Engg., 51–55, Feb., 2000 Novak, D Single Minded – Single Crystal Diamond Cutting Tool Engg., 38–41, June 2002 Raymond, M.K Ceramics Ease Up the Machining... under the high temperatures and sustained pressures that occur during cutting, the diamond has a tendency to revert back to graphite, after only a few seconds in-cut This reversion, does Figure 13.  Cutting tool materials: Cubic Boron Nitride (CBN) and Polycrystalline Diamond (PCD) [Courtesy of DeBeers – element 6] Cutting Tool Materials 27 Simpo PDF Merge and Split Unregistered Version - http://www.simpopdf.com... edges to the coated tooling 1.2.8 Ceramics and Cermets The oldest cutting tool materials date back to over 100,000 BC and were ceramic (flints), as stone-aged people used these specially-prepared broken flints to cut and work into hunting tools such as arrowheads, spears and for knives when eating their hunted prey The first modern-day industrial applications of ceramics as cutting tools occurred in... suitably-shaped blanks, to fit the desired tool holder (as illustrated in Fig 13b) Both CBN and PCD cutting tools can successfully machine: super-alloys (ie with low iron content), grey cast iron and non-ferrous metals, but show distinct differences when other workpiece materials are to be productively machined – as depicted in Fig 14 Polycrystalline diamond cutting tools are not utilised for machining ferrous... moderate cutting speeds, although their reduced toughness, can upon the application of high feed rates, induce greater plastic deformation of the cutting edge and induce higher tool stresses These uncoated cutting inserts were very much the product of the past and today, virtually all such tooling inserts are multi-coated to significantly reduce the effects of dissolution wear and greatly extend the cutting . achieved. e cutting tool problems, such as: too wide a range of tooling inventory, inappropriate tools/out-dated tooling, or not enough tools for the overall operational 1 Tooling refers. today can range Figure 3. Cutting tool materials – toughness versus hardness – and their typical material characteristics. [Courtesy of Mitsubishi Carbide] . Cutting Tool Materials  Simpo PDF Merge. Cutting tool manufacturers, by careful balancing of these ve factors for the ideal cutting tool, can produce grades of inserts which distinctly vary, allowing a wide range of workpiece materials