Liên hệ 037.667.9506 hoặc email thekingheavengmail.com để nhờ đặt mua tất cả các tiêu chuẩn kỹ thuật quốc tế với giá rẻ. Tài liệu sẽ được gửi cho bạn trong 24 giờ kể từ ngày nhận thanh toán. ISO là tên viết tắt của Tổ chức Quốc tế về tiêu chuẩn hoá (International Organization for Standardization), được thành lập vào năm 1946 và chính thức hoạt động vào ngày 23021947, nhằm mục đích xây dựng các tiêu chuẩn về sản xuất, thương mại và thông tin. ISO có trụ sở ở Geneva (Thụy Sĩ) và là một tổ chức Quốc tế chuyên ngành có các thành viên là các cơ quan tiêu chuẩn Quốc gia của hơn 150 nước. Việt Nam gia nhập ISO vào năm 1977, là thành viên thứ 77 của tổ chức này. Tuỳ theo từng nước, mức độ tham gia xây dựng các tiêu chuẩn ISO có khác nhau. Ở một số nước, tổ chức tiêu chuẩn hoá là các cơ quan chính thức hay bán chính thức của Chính phủ. Tại Việt Nam, tổ chức tiêu chuẩn hoá là Tổng cục Tiêu chuẩn Đo lường Chất lượng, thuộc Bộ Khoa học và Công nghệ. Mục đích của các tiêu chuẩn ISO là tạo điều kiện cho các hoạt động trao đổi hàng hoá và dịch vụ trên toàn cầu trở nên dễ dàng, tiện dụng hơn và đạt được hiệu quả. Tất cả các tiêu chuẩn do ISO đặt ra đều có tính chất tự nguyện. Tuy nhiên, thường các nước chấp nhận tiêu chuẩn ISO và coi nó có tính chất bắt buộc. Có nhiều loại ISO: Hiện nay hệ thống quản lý chất lượng ISO 9001:2000 đã phát hành đến phiên bản thứ 4: ISO 9000 (1987), ISO 9000 (1994), ISO 9001 (2000), ISO 9001 (2008) Ngoài ra còn nhiều loại khác như: ISO14001:2004 Hệ thống quản lý môi trường. OHSAS18001:1999 Hệ thống quản lý vệ sinh và an toàn công việc. SA 8000:2001 Hệ thống quản lý trách nhiệm xã hội
INTERNATIONAL ISO STANDARD 25745-2 First edition 2015-04-01 AMENDMENT 1 2023-10 Energy performance of lifts, escalators and moving walks — Part 2: Energy calculation and classification for lifts (elevators) AMENDMENT 1: Express zones Performance énergétique des ascenseurs, escaliers mécaniques et trottoirs roulants — Partie 2: Calcul énergétique et classification des ascenseurs AMENDEMENT 1: Zones sans arrêt intermédiaire Reference number ISO 25745-2:2015/Amd.1:2023(E) © ISO 2023 ISO 25745-2:2015/Amd.1:2023(E) COPYRIGHT PROTECTED DOCUMENT © ISO 2023 All rights reserved Unless otherwise specified, or required in the context of its implementation, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission Permission can be requested from either ISO at the address below or ISO’s member body in the country of the requester ISO copyright office CP 401 • Ch de Blandonnet 8 CH-1214 Vernier, Geneva Phone: +41 22 749 01 11 Email: copyright@iso.org Website: www.iso.org Published in Switzerland ii © ISO 2023 – All rights reserved ISO 25745-2:2015/Amd.1:2023(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work of preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1 In particular, the different approval criteria needed for the different types of ISO document should be noted This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives) ISO draws attention to the possibility that the implementation of this document may involve the use of (a) patent(s) ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights in respect thereof As of the date of publication of this document, ISO had not received notice of (a) patent(s) which may be required to implement this document However, implementers are cautioned that this may not represent the latest information, which may be obtained from the patent database available at www.iso.org/patents ISO shall not be held responsible for identifying any or all such patent rights Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html This document was prepared by Technical Committee ISO/TC 178, Lifts, escalators and moving walks, in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/ TC 10, Lifts, escalators and moving walks, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement) A list of all parts in the ISO 25745 series can be found on the ISO website Any feedback or questions on this document should be directed to the user’s national standards body A complete listing of these bodies can be found at www.iso.org/members.html © ISO 2023 – All rights reserved iii ISO 25745-2:2015/Amd.1:2023(E) Energy performance of lifts, escalators and moving walks — Part 2: Energy calculation and classification for lifts (elevators) AMENDMENT 1: Express zones Scope Delete j) Delete NOTE 2 Renumber NOTE 1 as NOTE 3.2 Replace the definition with the following: section of the lift well whose distance between two adjacent landings exceeds three average floor distances 5.2.2 Replace the complete subclause with the following: a) For lifts without express zone, the average travel distance (sav) for the target installation shall be calculated by Formula (1) sav = pav × src (1) 100 where pav is the percentage of the average travel distance according to Table 2; src is the one-way travel distance of reference cycle according to ISO 25745-1 (m) Table 2 — Percentage of average travel distance Usage category 1-3 4 5 6 Number of stopping floors 49 % 32 % Percentage of average travel distance pav 2 100 % 3 > 3 67 % 44 % 39 % For lift applications in which the traffic patterns are well known, a specific percentage of the average travel distance can be agreed between the involved parties for the assessment of the annual energy consumption In this case, the selected percentage should be as documented in Annex B © ISO 2023 – All rights reserved 1 ISO 25745-2:2015/Amd.1:2023(E) b) For lifts with express zone, the average travel distance shall be calculated by Formula (2) sav = pav ×( src −( sez − sfl ))+ kez ×( sez − sfl ) (2) 100 100 where sez is the length of the express zone (m); sfl is the average floor distance (m); kez is the percentage of the number of trips passing through the express zone according to Table 3 Table 3 — Percentage of trips passing through the express zone Usage category 1-3 4 5 6 kez sez ≤ 75 m 58 % 40 % 25 % 18 % sez > 75 m 42 % 30 % 18 % 14 % NOTE Percentage values for usage categories 1-3 are estimations based on exponential trend identified within usage categories 4-6 In the case of multiple express zones, the individual zones shall be summed up as one single express zone for the calculation Renumber subsequent formulae by increasing their numbers by 2 Renumber subsequent tables by increasing their numbers by 1 Annex C Add the following symbols in alphabetical order: kez is the percentage of the number of trips passing through the express zone pav is the percentage of the average travel distance (%) sez is the length of the express zone (m) sfl is the average floor distance (m) 2 © ISO 2023 – All rights reserved ISO 25745-2:2015/Amd.1:2023(E) ICS 91.140.90 Price based on 2 pages © ISO 2023 – All rights reserved