Biện pháp thi công (Manner of Execution hoặc construction method statement) là trình tự và cách thi công 1 công trình cụ thể từ lúc bắt đầu thi công đến lúc kết thúc và bàn giao công trình, trong đó biện pháp thi công (BPTC) phải đề ra được: hiệu quả về thời gian, hiệu quả về phòng chống (như: tai nạn, phòng cháy…)
***** HA NOI CITY RING ROAD NO.3 CONSTRUCTION PROJECT Package 03: THANH XUAN - NORTH LINH DAM LAKE SECTION *** construction method DRAWING Item: girder erection of spans P154-P155 and P155-P156 (From casting yard no.1) submitted 1.st ELEVATION A Crane 100T Crane 100T P155 A PLAN VIEW P156 P155 12000 P154 P155 P156 P154 P155 - Transported girder to installation girder span follow that had been approved 10000 10000 - Girders are installation with two cranes 100T Before loading girders to span, it is necessary to try girders loading test about 20cm from girder truck and then stop to check brake and winch system of the crane Girders loading would only be continued after ensuring the safety Access road 50cm sand compacted Crane 100T Crane 100T - Those who have done absolutely obey the orders of the commander, the commander must have a whistle, orders flags to be clear c n c nh nh nh c a n c huy, n c huy ,c nh nh cr - In this drawing showing arrangement method for girder launching at span P155-P156 With span P154-P155 the work progresses similar 22400 22400 Median range between 28000 R7.9m 9m R7 10 - Dimensions are mm, levels are m 40000 12000 - Control traffic see other drawing MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van typical section SIGNATURE DATE tlc - cienco - cienco SECTION A - A CL 8000 sidewalk 2% 12000 nmv lane 6% Detail frontage road - lanes Point mark cone / Fence 6% 2% 2% 28000 R.o.w limit b=68.0m Super T girder 3000 6000 2300 3600 31000 3600 2300 6000 3000 DETAIL 200 200 Wooden sleeper 1000x200x200 Steel plate 1500x6000x20 mm 20 38000 7700 - Dimensions are mm, levels are m - Location of the crane must be supported strongly 15800 MINISTRY OF TRANSPORT noi city ring road no.3 construction project drawing TITLE scale PROJECT MANAGEMENT UNIT THANG LONG as shown drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van typical cross-section SIGNATURE DATE tlc - cienco - cienco P155 STEP 1: - Lift up the girder to pier head and combination to rotate the crane to move the girder inside (10minutes) P156 P155 STEP 2: - Take rotating crane to move the girder inside, get the girder down to pier head, move two crane inside During this time, the truck run to the yard girder to get girder.(45 minutes) P156 Move crane Move crane Crane 100T Crane 100T This position to get down girder to change Crane Crane 100T Crane 100T R7.9m R7.9m R7.9m R7.9m P155 STEP 3: - Left crane rotate girders into place, move crane inside right crane hang girder (45 minutes) P156 P155 Move crane STEP 4: - Two crane rotate girders into place Move left crane inside (45 minutes) Move crane Crane 100T P156 Crane 100T Crane 100T Next position of girder R7.9m Next position of girder R7.9m Crane 100T R7.9m R7.9m MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE drawing no PROJECT MANAGEMENT UNIT THANG LONG as shown (1/14) 02 title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 6: - To get the girder down to position (5 minutes) STEP 5: - Two crane rotate girders into place (10 minutes) P155 P156 P155 P156 Crane 100T R7.9m Crane 100T R7.9m Crane 100T Crane 100T R7.9m R7.9m - Dimensions are mm, levels are m - Total estimated installation time a girder is 160 minutes MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (2/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 2: - Take rotating crane to move the girder inside, get the girder down to pier head, move two crane inside During this time, the truck run to the yard girder to get girder.(45 minutes) STEP 1: - Lift up the girder to pier head and combination to rotate the crane to move the girder inside (10minutes) P155 P156 P155 P156 Move crane Move crane Crane 100T Crane 100T This position to get down girder to change Crane Crane 100T Crane 100T R7.9m R7.9m R7.9m R7.9m STEP 3: - Left crane rotate girders into place, move crane inside right crane hang girder (45 minutes) P155 STEP 4: - Two crane rotate girders into place (10 minutes) P156 P155 P156 Move crane Crane 100T Crane 100T Crane 100T Next position of girder R7.9m R7.9m Next position of girder Crane 100T R7.9m R7.9m MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (3/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 5: - To get the girder down to position (5 minutes) P155 P156 Crane 100T R7.9m R7.9m Crane 100T - Dimensions are mm, levels are m - Total estimated installation time a girder is 115 minutes MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (4/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 2: - Take rotating crane to move the girder inside, get the girder down to pier head, move two crane inside During this time, the truck run to the yard girder to get girder.(45 minutes) STEP 1: - Lift up the girder to pier head and combination to rotate the crane to move the girder inside (10minutes) P155 P156 P155 P156 Move crane Move crane Crane 100T Crane 100T This position to get down girder to change Crane Crane 100T Crane 100T R7.9m R7.9m R7.9m R7.9m STEP 3: - Left crane rotate girders into place, move crane inside right crane hang girder (45 minutes) P155 STEP 4: - Two crane rotate girders into place (10 minutes) P156 P155 P156 Move crane Crane 100T Crane 100T Crane 100T R7.9m Next position of girder R7.9m R7.9m Crane 100T R7.9m MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (5/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 5: - To get the girder down to position (5 minutes) P155 P156 Crane 100T R7.9m R7.9m Crane 100T - Dimensions are mm, levels are m - Total estimated installation time a girder is 115 minutes MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (6/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 2: - Take rotating crane to move the girder inside, get the girder down to pier head, move two crane inside During this time, the truck run to the yard girder to get girder.(45 minutes) STEP 1: - Lift up the girder to pier head and combination to rotate the crane to move the girder inside (10minutes) P155 P156 P155 P156 Move crane Move crane Crane 100T Crane 100T This position to get down girder to change Crane Crane 100T Crane 100T R7.9m R7.9m R7.9m R7.9m STEP 3: - Left crane rotate girders into place, move crane inside right crane hang girder (45 minutes) P155 STEP 4: - Two crane rotate girders into place (10 minutes) P156 P155 P156 Move crane Crane 100T Crane 100T Crane 100T R7.9m Next position of girder R7.9m R7.9m Crane 100T R7.9m MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (7/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 5: - To get the girder down to position (5 minutes) P155 P156 R7.9m R7.9m Crane 100T Crane 100T - Dimensions are mm, levels are m - Total estimated installation time a girder is 115 minutes MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (8/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 2: - Take rotating crane to move the girder inside, get the girder down to pier head, move two crane inside During this time, the truck run to the yard girder to get girder.(45 minutes) STEP 1: - Lift up the girder to pier head and combination to rotate the crane to move the girder inside (10minutes) P155 P156 P155 P156 Move crane Move crane Crane 100T Crane 100T Crane 100T This position to get down girder to change Crane R7.9m R7.9m Crane 100T R7.9m R7.9m STEP 3: - Left crane rotate girders into place, move crane inside right crane hang girder (45 minutes) P155 STEP 4: - Right crane rotate girders into place left crane hang girder (10 minutes) P156 P155 P156 Move crane Crane 100T Crane 100T Crane 100T R7.9m R7.9m R7.9m R7.9m MINISTRY OF TRANSPORT noi city ring road no.3 construction project Crane 100T scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (9/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 5: - To get the girder down to position (5 minutes) P155 P156 Crane 100T R7.9m R7.9m Crane 100T - Dimensions are mm, levels are m - Total estimated installation time a girder is 115 minutes MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (10/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 2: - Take rotating crane to move the girder inside, get the girder down to pier head, move two crane inside During this time, the truck run to the yard girder to get girder.(45 minutes) STEP 1: - Lift up the girder to pier head and combination to rotate the crane to move the girder inside (10minutes) P155 P156 P155 P156 Move crane Move crane Crane 100T Crane 100T This position to get down girder to change Crane Crane 100T R7.9m R7.9m Crane 100T R7.9m R7.9m STEP 3: - Left crane rotate girders into place, move crane inside right crane hang girder (45 minutes) P155 STEP 4: - To get the girder down to position (5 minutes) P156 P155 Move crane P156 Move crane Crane 100T Crane 100T R7.9m R7.9m - Dimensions are mm, levels are m - Total estimated installation time a girder is 105 minutes MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (11/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 2: - Take rotating crane to move the girder inside During this time, the truck run to the yard girder to get girder.(15 minutes) STEP 1: - Lift up the girder to pier head and combination to rotate the crane to move the girder inside (10minutes) P155 P156 P155 Crane 100T P156 Crane 100T Crane 100T R7.9m R7.9m R7.9m R7.9m Crane 100T STEP 3: - To get the girder down to position (5 minutes) P155 P156 Crane 100T - Dimensions are mm, levels are m - Total estimated installation time a girder is 30 minutes R7.9m MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (12/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 2: - Take rotating crane to move the girder inside During this time, the truck run to the yard girder to get girder.(15 minutes) STEP 1: - Lift up the girder to pier head and combination to rotate the crane to move the girder inside (10minutes) P155 P156 P155 Crane 100T P156 Crane 100T Crane 100T R7.9m R7.9m R7.9m R7.9m Crane 100T STEP 3: - To get the girder down to position (5 minutes) P155 P156 Crane 100T - Dimensions are mm, levels are m - Total estimated installation time a girder is 30 minutes R7.9m R7.9m MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (13/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco STEP 1: - Lift up the girder to pier head (10minutes) P155 STEP 2: - To get the girder down to position (10 minutes) P156 P155 1 2 4 Crane 100T P156 Crane 100T 6 7 R7.9m 9m R7 Crane 100T Crane 100T STEP 1: - Lift up the girder to pier head (10minutes) P155 STEP 2: - To get the girder down to position (10 minutes) P156 P155 1 2 4 Crane 100T P156 Crane 100T 6 7 R7.9m 9m R7 10 Crane 100T Crane 100T - Dimensions are mm, levels are m - Total estimated installation time a girder(number or 10) is 20 minutes MINISTRY OF TRANSPORT noi city ring road no.3 construction project scale drawing TITLE PROJECT MANAGEMENT UNIT THANG LONG as shown (14/14) drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco Vehicle lane / Ph Transported girder direction / 28000 Truck carry girder Point mark cone 3m/unit 6000 Barrie (3 mobile barrie) Flag man 6000 Vehicle lane / Ph Median range between Fence NOTES: 127 134 125 SPEED LIMIT 20Km/h FINISH SPEED LIMITS 20Km/h DISALLOW OVERCOME 133 DISALLOW OVERCOME - Dimension drawing unit mm - Only progress installation the girder after 23h p.m - Comply with road signs charter 22TCN 237-01 - During the girder installation must be arranged worker to ensure safety for people and vehicles traffic - Traffic safe layout for each installation span girder The signs are always revolving for each installation span girder AHEAD AHEAD 100m 50m WORKS WORKS PROHIBIT ALL EXCEEDED 442b MINISTRY OF TRANSPORT noi city ring road no.3 construction project 442c drawing TITLE scale PROJECT MANAGEMENT UNIT THANG LONG traffic safe while erection girder as shown drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco BARRIE 2100 The sign T2 T2 T3 53 1200 1450 200 T1 T4 200 T5 150 8x200 150 Solid rubber tyre MINISTRY OF TRANSPORT noi city ring road no.3 construction project 500 750 drawing TITLE scale PROJECT MANAGEMENT UNIT THANG LONG traffic safe while erection girder as shown drawing no title full NAME DESIGNED BY: Phan anh tai CHECKED BY: dong nhu thai APPROVED BY: pham van SIGNATURE DATE tlc - cienco - cienco