Nissan altima esm tai lieu sua chua phan 2

Tài liệu hướng dẫn sửa chữa xe Nissan altima esm tai lieu sua chua phan 2 . Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành chẩn đoán, sửa chữa nhanh chóng, chính xác, hiệu quả, hợp lý nhất

BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY SECTION DLK DOOR & LOCK A B C D E CONTENTS COUPE BASIC INSPECTION 11 DIAGNOSIS AND REPAIR WORKFLOW 11 Work Flow 11 INSPECTION AND ADJUSTMENT 14 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT 14 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description 14 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement 14 FUNCTION DIAGNOSIS 15 AUTOMATIC DOOR LOCKS .15 System Diagram 15 System Description 15 Component Parts Location 17 Component Description 17 DOOR LOCK FUNCTION 18 DOOR LOCK AND UNLOCK SWITCH 18 DOOR LOCK AND UNLOCK SWITCH : System Diagram 18 DOOR LOCK AND UNLOCK SWITCH : System Description 18 DOOR LOCK AND UNLOCK SWITCH : Component Parts Location 19 DOOR LOCK AND UNLOCK SWITCH : Component Description 19 DOOR REQUEST SWITCH 19 DOOR REQUEST SWITCH : System Diagram 20 DOOR REQUEST SWITCH : System Description 20 DOOR REQUEST SWITCH : Component Parts Location 23 DOOR REQUEST SWITCH : Component Description 24 Revision: September 2009 INTELLIGENT KEY 25 INTELLIGENT KEY : System Diagram 25 INTELLIGENT KEY : System Description .25 INTELLIGENT KEY : Component Parts Location 28 INTELLIGENT KEY : Component Description 29 TRUNK OPEN FUNCTION 30 TRUNK LID OPENER SWITCH 30 TRUNK LID OPENER SWITCH : System Diagram 30 TRUNK LID OPENER SWITCH : System Description 30 TRUNK LID OPENER SWITCH : Component Parts Location 31 TRUNK LID OPENER SWITCH : Component Description 31 TRUNK REQUEST SWITCH .31 TRUNK REQUEST SWITCH : System Diagram 32 TRUNK REQUEST SWITCH : System Description 32 TRUNK REQUEST SWITCH : Component Parts Location 35 TRUNK REQUEST SWITCH : Component Description 36 INTELLIGENT KEY 37 INTELLIGENT KEY : System Diagram 37 INTELLIGENT KEY : System Description .37 INTELLIGENT KEY : Component Parts Location 39 INTELLIGENT KEY : Component Description 40 F G H I J DLK L M N O WARNING FUNCTION 41 System Description 41 Component Parts Location 46 KEY REMINDER FUNCTION 48 System Description 48 Component Parts Location 49 HOMELINK UNIVERSAL TRANSCEIVER 51 DLK-1 2010 Altima P Component Description 51 DIAGNOSIS SYSTEM (BCM) 52 COMMON ITEM 52 COMMON ITEM : Diagnosis Description 52 COMMON ITEM : CONSULT-III Function 52 DOOR LOCK 53 DOOR LOCK : CONSULT-III Function (BCM DOOR LOCK) 53 INTELLIGENT KEY 53 INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) 53 TRUNK 56 TRUNK : CONSULT-III Function (BCM - TRUNK) 56 COMPONENT DIAGNOSIS 58 U1000 CAN COMM CIRCUIT 58 Description 58 DTC Logic 58 Diagnosis Procedure 58 U1010 CONTROL UNIT (CAN) 59 DTC Logic 59 Diagnosis Procedure 59 Special Repair Requirement 59 B2622 INSIDE KEY ANTENNA 60 Description 60 DTC Logic 60 Diagnosis Procedure 60 B2623 INSIDE KEY ANTENNA 63 Description 63 DTC Logic 63 Diagnosis Procedure 63 POWER SUPPLY AND GROUND CIRCUIT 66 Diagnosis Procedure 66 Special Repair Requirement 66 DOOR SWITCH 67 Description 67 Component Function Check 67 Diagnosis Procedure 67 Component Inspection 69 DOOR LOCK AND UNLOCK SWITCH 70 DRIVER SIDE 70 DRIVER SIDE : Description 70 DRIVER SIDE : Component Function Check 70 DRIVER SIDE : Diagnosis Procedure (With LH and RH Anti-Pinch) 70 DRIVER SIDE : Diagnosis Procedure (With LH Anti-Pinch Only) 72 PASSENGER SIDE 73 PASSENGER SIDE : Description 73 Revision: September 2009 PASSENGER SIDE : Component Function Check 73 PASSENGER SIDE : Diagnosis Procedure (With LH and RH Anti-Pinch) 73 PASSENGER SIDE : Diagnosis Procedure (With LH Anti-Pinch Only) 75 KEY SLOT 77 Description 77 Component Function Check 77 Diagnosis Procedure 77 Component Inspection 78 KEY CYLINDER SWITCH 79 Description 79 Component Function Check 79 Diagnosis Procedure (With LH and RH Anti-Pinch) 79 Diagnosis Procedure (With LH Anti-Pinch Only) 80 Component Inspection 82 UNLOCK SENSOR 83 Description 83 Component Function Check 83 Diagnosis Procedure 83 Component Inspection 85 TRUNK LID OPENER SWITCH 86 Description 86 Component Function Check 86 Diagnosis Procedure 86 Component Inspection 87 TRUNK LID OPENER CANCEL SWITCH 89 Description 89 Component Function Check 89 Diagnosis Procedure 89 Component Inspection 90 TRUNK ROOM LAMP SWITCH 92 Description 92 Component Function Check 92 Diagnosis Procedure 92 Component Inspection 94 DOOR REQUEST SWITCH 95 Description 95 Component Function Check 95 Diagnosis Procedure 95 Component Inspection 97 TRUNK OPENER REQUEST SWITCH 99 Description 99 Component Function Check 99 Diagnosis Procedure 99 Component Inspection 101 DOOR LOCK ACTUATOR 102 DRIVER SIDE 102 DRIVER SIDE : Description 102 DLK-2 2010 Altima DRIVER SIDE : Component Function Check 102 DRIVER SIDE : Diagnosis Procedure 102 PASSENGER SIDE 103 PASSENGER SIDE : Description 103 PASSENGER SIDE : Component Function Check 103 PASSENGER SIDE : Diagnosis Procedure 103 HOMELINK UNIVERSAL TRANSCEIVER 124 Description 124 Component Function Check 124 Diagnosis Procedure 124 A ECU DIAGNOSIS 126 B BCM (BODY CONTROL MODULE) 126 Reference Value 126 Terminal Layout 130 Physical Values 130 Fail Safe 148 DTC Inspection Priority Chart 148 DTC Index 149 C Description 107 Component Function Check 107 Diagnosis Procedure 107 Component Inspection 108 WIRING DIAGRAM 154 E OUTSIDE KEY ANTENNA 109 POWER DOOR LOCK SYSTEM 156 Description 109 Component Function Check 109 Diagnosis Procedure 109 Wiring Diagram 156 TRUNK LID OPENER ACTUATOR 105 Description 105 Component Function Check 105 Diagnosis Procedure 105 INTELLIGENT KEY WARNING BUZZER 107 D HOMELINK UNIVERSAL TRANSCEIVER 154 Wiring Diagram 154 INTELLIGENT KEY SYSTEM 166 F G Wiring Diagram 166 REMOTE KEYLESS ENTRY RECEIVER 112 Description 112 Component Function Check 112 Diagnosis Procedure 112 TRUNK LID OPENER 182 H Wiring Diagram 182 SYMPTOM DIAGNOSIS 186 I INTELLIGENT KEY BATTERY AND FUNCTION 115 INTELLIGENT KEY SYSTEM SYMPTOMS 186 Description 115 Component Function Check 115 Diagnosis Procedure 115 DOOR LOCK FUNCTION SYMPTOMS 187 KEY SLOT ILLUMINATION 117 DOOR LOCK AND UNLOCK SWITCH 187 DOOR LOCK AND UNLOCK SWITCH : Symptom Table 187 DLK DOOR REQUEST SWITCH 187 DOOR REQUEST SWITCH : Symptom Table 187 L Description 117 Component Function Check 117 Diagnosis Procedure 117 HORN FUNCTION 119 Description 119 Component Function Check 119 Diagnosis Procedure 119 COMBINATION METER DISPLAY FUNCTION 121 Description 121 Component Function Check 121 Diagnosis Procedure 121 WARNING CHIME FUNCTION 122 Description 122 Component Function Check 122 Diagnosis Procedure 122 HAZARD FUNCTION 123 Description 123 Component Function Check 123 Diagnosis Procedure 123 Revision: September 2009 Symptom Table 186 INTELLIGENT KEY 188 INTELLIGENT KEY : Symptom Table 188 J M TRUNK OPEN FUNCTION SYMPTOMS 190 TRUNK LID OPENER SWITCH 190 TRUNK LID OPENER SWITCH : Symptom Table 190 TRUNK REQUEST SWITCH 190 TRUNK REQUEST SWITCH : Symptom Table 190 INTELLIGENT KEY 190 INTELLIGENT KEY : Symptom Table 190 WARNING FUNCTION SYMPTOMS 192 Symptom Table 192 KEY REMINDER FUNCTION SYMPTOMS 194 Symptom Table 194 HAZARD FUNCTION 195 DLK-3 2010 Altima N O P Symptom Table .195 HORN FUNCTION 196 Symptom Table .196 INTEGRATED HOMELINK TRANSMITTER 197 TRUNK LID ASSEMBLY 224 TRUNK LID ASSEMBLY : Removal and Installation 224 TRUNK LID ASSEMBLY : Adjustment 225 Symptom Table .197 TRUNK LID LOCK 226 TRUNK LID LOCK : Removal and Installation 226 SQUEAK AND RATTLE TROUBLE DIAGNOSES 198 FUEL FILLER LID 227 Exploded View 227 Removal and Installation 227 Work Flow 198 Inspection Procedure .200 Diagnostic Worksheet 202 REMOTE KEYLESS ENTRY RECEIVER 228 PRECAUTION 204 Removal 228 Installation 228 SEDAN WITH INTELLIGENT KEY PRECAUTIONS 204 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 204 Procedure without Cowl Top Cover 204 Precaution for work 204 PREPARATION 205 BASIC INSPECTION 229 DIAGNOSIS AND REPAIR WORKFLOW 229 Work Flow 229 INSPECTION AND ADJUSTMENT 232 ON-VEHICLE REPAIR 206 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT 232 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description 232 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement 232 HOOD 206 FUNCTION DIAGNOSIS 233 HOOD ASSEMBLY 206 HOOD ASSEMBLY : Removal and Installation .206 HOOD ASSEMBLY : Adjustment 207 AUTOMATIC DOOR LOCKS 233 PREPARATION 205 Special Service Tools 205 Commercial Service Tools .205 HOOD LOCK CONTROL 209 HOOD LOCK CONTROL : Component Parts Location .209 HOOD LOCK CONTROL : Removal and Installation 209 RADIATOR CORE SUPPORT 212 Removal and Installation .212 FRONT FENDER 214 Removal and Installation .214 DOOR 217 FRONT DOOR 217 FRONT DOOR : Removal and Installation 217 FRONT DOOR : Adjustment 218 DOOR LOCK 220 FRONT DOOR LOCK 220 FRONT DOOR LOCK : Component Parts Location 220 FRONT DOOR LOCK : Removal and Installation 220 TRUNK LID 224 Revision: September 2009 System Diagram 233 System Description 233 Component Parts Location 235 Component Description 236 DOOR LOCK FUNCTION 237 DOOR LOCK AND UNLOCK SWITCH 237 DOOR LOCK AND UNLOCK SWITCH : System Diagram 237 DOOR LOCK AND UNLOCK SWITCH : System Description 237 DOOR LOCK AND UNLOCK SWITCH : Component Parts Location 238 DOOR LOCK AND UNLOCK SWITCH : Component Description 239 DOOR REQUEST SWITCH 239 DOOR REQUEST SWITCH : System Diagram 239 DOOR REQUEST SWITCH : System Description 239 DOOR REQUEST SWITCH : Component Parts Location 242 DOOR REQUEST SWITCH : Component Description 244 INTELLIGENT KEY 244 INTELLIGENT KEY : System Diagram 244 INTELLIGENT KEY : System Description 244 DLK-4 2010 Altima INTELLIGENT KEY : Component Parts Location 247 INTELLIGENT KEY : Component Description 249 TRUNK OPEN FUNCTION 250 TRUNK LID OPENER SWITCH 250 TRUNK LID OPENER SWITCH : System Diagram 250 TRUNK LID OPENER SWITCH : System Description 250 TRUNK LID OPENER SWITCH : Component Parts Location 251 TRUNK LID OPENER SWITCH : Component Description 251 TRUNK REQUEST SWITCH 251 TRUNK REQUEST SWITCH : System Diagram 252 TRUNK REQUEST SWITCH : System Description 252 TRUNK REQUEST SWITCH : Component Parts Location 255 TRUNK REQUEST SWITCH : Component Description 257 INTELLIGENT KEY 257 INTELLIGENT KEY : System Diagram 257 INTELLIGENT KEY : System Description 257 INTELLIGENT KEY : Component Parts Location 259 INTELLIGENT KEY : Component Description 261 WARNING FUNCTION 262 System Description 262 Component Parts Location 267 KEY REMINDER FUNCTION 270 System Description 270 Component Parts Location 271 HOMELINK UNIVERSAL TRANSCEIVER 274 Component Description 274 DIAGNOSIS SYSTEM (BCM) 275 COMMON ITEM 275 COMMON ITEM : Diagnosis Description 275 COMMON ITEM : CONSULT-III Function 275 DOOR LOCK 276 DOOR LOCK : CONSULT-III Function (BCM DOOR LOCK) 276 INTELLIGENT KEY 276 INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) 276 TRUNK 279 TRUNK : CONSULT-III Function (BCM - TRUNK) 279 COMPONENT DIAGNOSIS 281 U1000 CAN COMM CIRCUIT 281 Description 281 DTC Logic 281 Revision: September 2009 Diagnosis Procedure 281 U1010 CONTROL UNIT (CAN) 282 DTC Logic 282 Diagnosis Procedure 282 Special Repair Requirement 282 A B B2622 INSIDE KEY ANTENNA 283 Description 283 DTC Logic 283 Diagnosis Procedure 283 C B2623 INSIDE KEY ANTENNA 286 D Description 286 DTC Logic 286 Diagnosis Procedure 286 E POWER SUPPLY AND GROUND CIRCUIT 289 Diagnosis Procedure 289 Special Repair Requirement 289 F DOOR SWITCH 290 Description 290 Component Function Check 290 Diagnosis Procedure 290 Component Inspection 292 G H DOOR LOCK AND UNLOCK SWITCH 293 DRIVER SIDE 293 DRIVER SIDE : Description 293 DRIVER SIDE : Component Function Check 293 DRIVER SIDE : Diagnosis Procedure (With LH and RH Anti-Pinch) 293 DRIVER SIDE : Diagnosis Procedure (With LH Anti-Pinch Only) 295 PASSENGER SIDE 296 PASSENGER SIDE : Description 296 PASSENGER SIDE : Component Function Check 296 PASSENGER SIDE : Diagnosis Procedure (With LH and RH Anti-Pinch) 296 PASSENGER SIDE : Diagnosis Procedure (With LH Anti-Pinch Only) 298 KEY SLOT 300 Description 300 Component Function Check 300 Diagnosis Procedure 300 Component Inspection 301 I J DLK L M N O KEY CYLINDER SWITCH 302 Description 302 Component Function Check 302 Diagnosis Procedure (With LH and RH Anti-Pinch) 302 Diagnosis Procedure (With LH Anti-Pinch Only) 303 Component Inspection 305 UNLOCK SENSOR 306 Description 306 DLK-5 2010 Altima P Component Function Check 306 Diagnosis Procedure .306 Component Inspection 308 TRUNK LID OPENER SWITCH 309 Description .309 Component Function Check 309 Diagnosis Procedure .309 Component Inspection 310 TRUNK LID OPENER CANCEL SWITCH 311 INTELLIGENT KEY WARNING BUZZER 330 Description 330 Component Function Check 330 Diagnosis Procedure 330 Component Inspection 331 OUTSIDE KEY ANTENNA 332 Description 332 Component Function Check 332 Diagnosis Procedure 332 Description .311 Component Function Check 311 Diagnosis Procedure .311 Component Inspection 312 REMOTE KEYLESS ENTRY RECEIVER 335 TRUNK ROOM LAMP SWITCH 313 INTELLIGENT KEY BATTERY AND FUNCTION 339 Description .313 Component Function Check 313 Diagnosis Procedure .313 Component Inspection 315 Description 335 Component Function Check 335 Diagnosis Procedure 335 Description 339 Component Function Check 339 Diagnosis Procedure 339 DOOR REQUEST SWITCH 316 KEY SLOT ILLUMINATION 341 Description .316 Component Function Check 316 Diagnosis Procedure .316 Component Inspection 318 Description 341 Component Function Check 341 Diagnosis Procedure 341 TRUNK OPENER REQUEST SWITCH 320 Description .320 Component Function Check 320 Diagnosis Procedure .320 Component Inspection 322 DOOR LOCK ACTUATOR 323 DRIVER SIDE 323 DRIVER SIDE : Description 323 DRIVER SIDE : Component Function Check .323 DRIVER SIDE : Diagnosis Procedure 323 HORN FUNCTION 343 Description 343 Component Function Check 343 Diagnosis Procedure 343 COMBINATION METER DISPLAY FUNCTION 345 Description 345 Component Function Check 345 Diagnosis Procedure 345 WARNING CHIME FUNCTION 346 Description 346 Component Function Check 346 Diagnosis Procedure 346 PASSENGER SIDE 324 PASSENGER SIDE : Description 324 PASSENGER SIDE : Component Function Check 324 PASSENGER SIDE : Diagnosis Procedure 324 HAZARD FUNCTION 347 REAR LH 325 REAR LH : Description 325 REAR LH : Component Function Check 325 REAR LH : Diagnosis Procedure 325 HOMELINK UNIVERSAL TRANSCEIVER 348 REAR RH 326 REAR RH : Description 326 REAR RH : Component Function Check .326 REAR RH : Diagnosis Procedure 326 ECU DIAGNOSIS 350 TRUNK LID OPENER ACTUATOR 328 Description .328 Component Function Check 328 Diagnosis Procedure .328 Revision: September 2009 Description 347 Component Function Check 347 Diagnosis Procedure 347 Description 348 Component Function Check 348 Diagnosis Procedure 348 BCM (BODY CONTROL MODULE) 350 Reference Value 350 Terminal Layout 354 Physical Values 354 Fail Safe 372 DTC Inspection Priority Chart 372 DLK-6 2010 Altima DTC Index 373 PRECAUTION 429 WIRING DIAGRAM 378 PRECAUTIONS 429 Wiring Diagram 391 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 429 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 429 Procedure without Cowl Top Cover 430 Precaution for work 430 TRUNK LID OPENER 407 PREPARATION 431 HOMELINK UNIVERSAL TRANSCEIVER 378 Wiring Diagram 378 POWER DOOR LOCK SYSTEM 380 Wiring Diagram 380 INTELLIGENT KEY SYSTEM 391 Wiring Diagram 407 SYMPTOM DIAGNOSIS 411 INTELLIGENT KEY SYSTEM SYMPTOMS 411 A B C D PREPARATION 431 Special Service Tools 431 Commercial Service Tools 431 E Symptom Table 411 ON-VEHICLE REPAIR 432 DOOR LOCK FUNCTION SYMPTOMS 412 HOOD 432 DOOR LOCK AND UNLOCK SWITCH 412 DOOR LOCK AND UNLOCK SWITCH : Symptom Table 412 HOOD ASSEMBLY 432 HOOD ASSEMBLY : Removal and Installation 432 HOOD ASSEMBLY : Adjustment 433 G DOOR REQUEST SWITCH 412 DOOR REQUEST SWITCH : Symptom Table 412 H INTELLIGENT KEY 413 INTELLIGENT KEY : Symptom Table 413 HOOD LOCK CONTROL 435 HOOD LOCK CONTROL : Component Parts Location 435 HOOD LOCK CONTROL : Removal and Installation 435 TRUNK OPEN FUNCTION SYMPTOMS 415 RADIATOR CORE SUPPORT 438 TRUNK LID OPENER SWITCH 415 TRUNK LID OPENER SWITCH : Symptom Table 415 TRUNK REQUEST SWITCH 415 TRUNK REQUEST SWITCH : Symptom Table 415 INTELLIGENT KEY 415 INTELLIGENT KEY : Symptom Table 415 WARNING FUNCTION SYMPTOMS 417 Symptom Table 417 KEY REMINDER FUNCTION SYMPTOMS 419 Symptom Table 419 HAZARD FUNCTION 420 Symptom Table 420 HORN FUNCTION 421 Symptom Table 421 INTEGRATED HOMELINK TRANSMITTER 422 Symptom Table 422 SQUEAK AND RATTLE TROUBLE DIAGNOSES 423 Work Flow 423 Inspection Procedure 425 Diagnostic Worksheet 427 Revision: September 2009 Removal and Installation 438 F I J FRONT FENDER 440 Removal and Installation 440 DLK DOOR 443 FRONT DOOR 443 FRONT DOOR : Removal and Installation 443 FRONT DOOR : Adjustment 444 L BACK DOOR 445 BACK DOOR : Removal and Installation 445 BACK DOOR : Adjustment 446 M DOOR LOCK 449 FRONT DOOR LOCK 449 FRONT DOOR LOCK : Component Parts Location 449 FRONT DOOR LOCK : Removal and Installation 449 BACK DOOR LOCK 452 BACK DOOR LOCK : Component Parts Location 452 BACK DOOR LOCK : Removal and Installation 452 TRUNK LID 456 TRUNK LID ASSEMBLY 456 DLK-7 2010 Altima N O P TRUNK LID ASSEMBLY : Removal and Installation 456 TRUNK LID ASSEMBLY : Adjustment 457 TRUNK LID LOCK 458 TRUNK LID LOCK : Removal and Installation .458 FUEL FILLER LID 459 Exploded View .459 Removal and Installation .459 REMOTE KEYLESS ENTRY RECEIVER 460 Removal 460 Installation .460 SEDAN WITHOUT INTELLIGENT KEY BASIC INSPECTION 461 COMMON ITEM : Diagnosis Description 478 COMMON ITEM : CONSULT-III Function 478 DOOR LOCK 479 DOOR LOCK : CONSULT-III Function (BCM DOOR LOCK) 479 MULTI REMOTE ENT 479 MULTI REMOTE ENT : CONSULT-III Function (BCM - MULTIREMOTE ENT) 479 TRUNK 481 TRUNK : CONSULT-III Function (BCM - TRUNK) 481 COMPONENT DIAGNOSIS 482 U1000 CAN COMM CIRCUIT 482 Work Flow 461 Description 482 DTC Logic 482 Diagnosis Procedure 482 INSPECTION AND ADJUSTMENT 464 U1010 CONTROL UNIT (CAN) 483 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT .464 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description .464 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement 464 B2622 INSIDE KEY ANTENNA 484 DIAGNOSIS AND REPAIR WORKFLOW 461 FUNCTION DIAGNOSIS 465 AUTOMATIC DOOR LOCKS 465 System Diagram 465 System Description 465 Component Parts Location 467 Component Description 467 DOOR LOCK FUNCTION 469 System Diagram 469 System Description 469 Component Parts Location 470 Component Description 470 REMOTE KEYLESS ENTRY SYSTEM 471 System Diagram 471 System Description 471 Component Parts Location 473 Component Description 474 TRUNK OPEN FUNCTION 475 System Diagram 475 System Description 475 Component Parts Location 476 Component Description 476 HOMELINK UNIVERSAL TRANSCEIVER 477 Component Description 477 DIAGNOSIS SYSTEM (BCM) 478 COMMON ITEM .478 Revision: September 2009 DTC Logic 483 Diagnosis Procedure 483 Special Repair Requirement 483 Description 484 DTC Logic 484 Diagnosis Procedure 484 B2623 INSIDE KEY ANTENNA 487 Description 487 DTC Logic 487 Diagnosis Procedure 487 POWER SUPPLY AND GROUND CIRCUIT 490 Diagnosis Procedure 490 Special Repair Requirement 490 DOOR SWITCH 491 Description 491 Component Function Check 491 Diagnosis Procedure 491 Component Inspection 493 DOOR LOCK AND UNLOCK SWITCH 494 DRIVER SIDE 494 DRIVER SIDE : Description 494 DRIVER SIDE : Component Function Check 494 DRIVER SIDE : Diagnosis Procedure 494 PASSENGER SIDE 496 PASSENGER SIDE : Description 496 PASSENGER SIDE : Component Function Check 496 PASSENGER SIDE : Diagnosis Procedure 496 KEY SLOT 498 Description 498 Component Function Check 498 Diagnosis Procedure 498 DLK-8 2010 Altima Component Inspection 499 KEY CYLINDER SWITCH 500 Component Function Check 519 Diagnosis Procedure 519 A Description 500 Component Function Check 500 Diagnosis Procedure 500 Component Inspection 501 KEYFOB BATTERY AND FUNCTION 523 Description 523 Component Function Check 523 Diagnosis Procedure 523 B TRUNK LID OPENER SWITCH 503 KEY SLOT ILLUMINATION 525 C Description 503 Component Function Check 503 Diagnosis Procedure 503 Component Inspection 504 Description 525 Component Function Check 525 Diagnosis Procedure 525 TRUNK LID OPENER CANCEL SWITCH 505 Description 505 Component Function Check 505 Diagnosis Procedure 505 Component Inspection 506 TRUNK ROOM LAMP SWITCH 507 Description 507 Component Function Check 507 Diagnosis Procedure 507 Component Inspection 509 DOOR LOCK ACTUATOR 510 DRIVER SIDE 510 DRIVER SIDE : Description 510 DRIVER SIDE : Component Function Check 510 DRIVER SIDE : Diagnosis Procedure 510 PASSENGER SIDE 511 PASSENGER SIDE : Description 511 PASSENGER SIDE : Component Function Check 511 PASSENGER SIDE : Diagnosis Procedure 511 REAR LH 512 REAR LH : Description 512 REAR LH : Component Function Check 512 REAR LH : Diagnosis Procedure 512 Description 527 Component Function Check 527 Diagnosis Procedure 527 E COMBINATION METER DISPLAY FUNCTION 529 F Description 529 Component Function Check 529 Diagnosis Procedure 529 Description 530 Component Function Check 530 Diagnosis Procedure 530 H HAZARD FUNCTION 531 I Description 531 Component Function Check 531 Diagnosis Procedure 531 J ECU DIAGNOSIS 532 BCM (BODY CONTROL MODULE) 532 DLK Reference Value 532 Terminal Layout 536 Physical Values 536 Fail Safe 554 DTC Inspection Priority Chart 554 DTC Index 555 WIRING DIAGRAM 560 TRUNK LID OPENER ACTUATOR 515 POWER DOOR LOCK SYSTEM 562 OUTSIDE WARNING BUZZER 517 HOMELINK UNIVERSAL TRANSCEIVER 560 Wiring Diagram 560 Wiring Diagram 562 L M N O REMOTE KEYLESS ENTRY SYSTEM 572 Wiring Diagram 572 Description 517 Component Function Check 517 Diagnosis Procedure 517 Component Inspection 518 TRUNK LID OPENER 584 REMOTE KEYLESS ENTRY RECEIVER 519 DOOR LOCK FUNCTION 588 Description 519 Symptom Table 588 Revision: September 2009 G WARNING CHIME FUNCTION 530 REAR RH 513 REAR RH : Description 513 REAR RH : Component Function Check 513 REAR RH : Diagnosis Procedure 513 Description 515 Component Function Check 515 Diagnosis Procedure 515 D HORN FUNCTION 527 Wiring Diagram 584 SYMPTOM DIAGNOSIS 588 DLK-9 2010 Altima P REMOTE KEYLESS ENTRY SYSTEM 589 RADIATOR CORE SUPPORT 608 Symptom Table .589 Removal and Installation 608 TRUNK OPEN FUNCTION 591 FRONT FENDER 610 Symptom Table .591 Removal and Installation 610 WARNING FUNCTION 592 DOOR 613 Symptom Table .592 SQUEAK AND RATTLE TROUBLE DIAGNOSES 594 Work Flow 594 Inspection Procedure .596 Diagnostic Worksheet 598 PRECAUTION 600 PRECAUTIONS 600 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 600 Procedure without Cowl Top Cover 600 Precaution for work 600 FRONT DOOR 613 FRONT DOOR : Removal and Installation 613 FRONT DOOR : Adjustment 614 BACK DOOR 615 BACK DOOR : Removal and Installation 615 BACK DOOR : Adjustment 616 DOOR LOCK 619 FRONT DOOR LOCK 619 FRONT DOOR LOCK : Component Parts Location 619 FRONT DOOR LOCK : Removal and Installation 619 PREPARATION 601 BACK DOOR LOCK 621 BACK DOOR LOCK : Component Parts Location 622 BACK DOOR LOCK : Removal and Installation 622 PREPARATION 601 TRUNK LID 625 Special Service Tools 601 Commercial Service Tools .601 ON-VEHICLE REPAIR 602 HOOD 602 HOOD ASSEMBLY 602 HOOD ASSEMBLY : Removal and Installation .602 HOOD ASSEMBLY : Adjustment 603 HOOD LOCK CONTROL 605 HOOD LOCK CONTROL : Component Parts Location .605 HOOD LOCK CONTROL : Removal and Installation 605 Revision: September 2009 TRUNK LID ASSEMBLY 625 TRUNK LID ASSEMBLY : Removal and Installation 625 TRUNK LID ASSEMBLY : Adjustment 626 TRUNK LID LOCK 627 TRUNK LID LOCK : Removal and Installation 627 FUEL FILLER LID 628 Exploded View 628 Removal and Installation 628 REMOTE KEYLESS ENTRY RECEIVER 629 Removal 629 Installation 629 DLK-10 2010 Altima NORMAL OPERATING CONDITION [VQ35DE] < SYMPTOM DIAGNOSIS > NORMAL OPERATING CONDITION Description A INFOID:0000000005431918 FUEL CUT CONTROL (AT NO LOAD AND HIGH ENGINE SPEED) EC If the engine speed is above 2,000 rpm under no load (for example, the selector lever position is P or N and engine speed is over 2,000 rpm) fuel will be cut off after some time The exact time when the fuel is cut off varies based on engine speed Fuel cut will be operated until the engine speed reaches 1,100 rpm, then fuel cut will be cancelled NOTE: This function is different from deceleration control listed under Multiport Fuel Injection (MFI) System, EC-1081, "System Description" C D E F G H I J K L M N O P Revision: September 2009 EC-1599 2010 Altima PRECAUTIONS [VQ35DE] < PRECAUTION > PRECAUTION PRECAUTIONS Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000005716652 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision This system includes seat belt switch inputs and dual stage front air bag modules The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this Service Manual WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system For removal of Spiral Cable and Air Bag Module, see the “SRS AIR BAG” • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury • When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the battery, and wait at least minutes before performing any service Precautions For Xenon Headlamp Service INFOID:0000000005716653 WARNING: Comply with the following warnings to prevent any serious accident • Disconnect the battery cable (negative terminal) or the power supply fuse before installing, removing, or touching the xenon headlamp (bulb included) The xenon headlamp contains high-voltage generated parts • Never work with wet hands • Check the xenon headlamp ON-OFF status after assembling it to the vehicle Never turn the xenon headlamp ON in other conditions Connect the power supply to the vehicle-side connector (Turning it ON outside the lamp case may cause fire or visual impairments.) • Never touch the bulb glass immediately after turning it OFF It is extremely hot CAUTION: Comply with the following cautions to prevent any error and malfunction • Install the xenon bulb securely (Insufficient bulb socket installation may melt the bulb, the connector, the housing, etc by high-voltage leakage or corona discharge.) • Never perform HID circuit inspection with a tester • Never touch the xenon bulb glass with hands Never put oil and grease on it • Dispose of the used xenon bulb after packing it in thick vinyl without breaking it • Never wipe out dirt and contamination with organic solvent (thinner, gasoline, etc.) Revision: September 2009 EC-1600 2010 Altima PRECAUTIONS [VQ35DE] < PRECAUTION > Precaution for Procedure without Cowl Top Cover INFOID:0000000005716654 A When performing the procedure after removing cowl top cover, cover the lower end of windshield with urethane, etc EC C D PIIB3706J On Board Diagnostic (OBD) System of Engine and CVT INFOID:0000000005431922 The ECM has an on board diagnostic system It will illuminate the malfunction indicator lamp (MIL) to warn the driver of a malfunction causing emission deterioration CAUTION: • Always to turn the ignition switch OFF and disconnect the negative battery cable before any repair or inspection work The open/short circuit of related switches, sensors, solenoid valves, etc will cause the MIL to illuminate • Always to connect and lock the connectors securely after work A loose (unlocked) connector will cause the MIL to illuminate due to the open circuit (Always the connector is free from water, grease, dirt, bent terminals, etc.) • Certain systems and components, especially those related to OBD, may use a new style slide-locking type harness connector For description and how to disconnect, refer to PG-60, "Description" (coupe) or PG-132, "Description" (sedan) • Always route and secure the harnesses properly after work The interference of the harness with a bracket, etc may cause the MIL to illuminate due to the short circuit • Always to connect rubber tubes properly after work A misconnected or disconnected rubber tube may cause the MIL to illuminate due to the malfunction of the EVAP system or fuel injection system, etc • Always to erase the unnecessary malfunction information (repairs completed) from the ECM and TCM (Transmission control module) before returning the vehicle to the customer General Precautions INFOID:0000000005431923 • Always use a 12 volt battery as power source • Never attempt to disconnect battery cables while engine is running • Before connecting or disconnecting the ECM harness connector, turn ignition switch OFF and disconnect negative battery cable Failure to so may damage the ECM because battery voltage is applied to ECM even if ignition switch is turned OFF • Before removing parts, turn ignition switch OFF and then disconnect battery ground cable E F G H I J K L M N SEF289H O • Never disassemble ECM • If a battery cable is disconnected, the memory will return to the ECM value The ECM will now start to self-control at its initial value Thus, engine operation can vary slightly in this case However, this is not an indication of a malfunction Never replace parts because of a slight variation • If the battery is disconnected, the following emission-related diagnostic information will be lost within 24 hours - Diagnostic trouble codes - 1st trip diagnostic trouble codes - Freeze frame data - 1st trip freeze frame data Revision: September 2009 EC-1601 2010 Altima P PRECAUTIONS < PRECAUTION > - System readiness test (SRT) codes - Test values • When connecting ECM harness connector, fasten (B) it securely with a lever (1) as far as it will go as shown in the figure - ECM (2) - Loosen (A) [VQ35DE] PBIB2947E • When connecting or disconnecting pin connectors into or from ECM, never damage pin terminals (bends or break) Check that there are not any bends or breaks on ECM pin terminal, when connecting pin connectors • Securely connect ECM harness connectors A poor connection can cause an extremely high (surge) voltage to develop in coil and condenser, thus resulting in damage to ICs • Keep engine control system harness at least 10 cm (4 in) away from adjacent harness, to prevent engine control system malfunctions due to receiving external noise, degraded operation of ICs, etc • Keep engine control system parts and harness dry • Before replacing ECM, perform ECM Terminals and Reference Value inspection and check that the ECM functions properly Refer to EC-1531, "Reference Value" • Handle mass air flow sensor carefully to avoid damage • Never clean mass air flow sensor with any type of detergent • Never disassemble electric throttle control actuator • Even a slight leakage in the air intake system can cause serious incidents • Never shock or jar the camshaft position sensor (PHASE), crankshaft position sensor (POS) PBIB0090E MEF040D • After performing each TROUBLE DIAGNOSIS, perform DTC Confirmation Procedure or Component Function Check The DTC should not be displayed in the DTC Confirmation Procedure if the repair is completed The Component Function Check should be a good result if the repair is completed SEF217U Revision: September 2009 EC-1602 2010 Altima PRECAUTIONS < PRECAUTION > • When measuring ECM signals with a circuit tester, never allow the two tester probes to contact Accidental contact of probes will cause a short circuit and damage the ECM power transistor [VQ35DE] A EC C D E F G SEF348N • B1 indicates bank 1, B2 indicates bank as shown in the figure • Never operate fuel pump when there is no fuel in lines • Tighten fuel hose clamps to the specified torque H I J SEC893C • Never depress accelerator pedal when starting • Immediately after starting, never rev up engine unnecessarily • Never rev up engine just prior to shutdown K L M N SEF709Y O P Revision: September 2009 EC-1603 2010 Altima PRECAUTIONS < PRECAUTION > • When installing C.B ham radio or a mobile phone, be sure to observe the following as it may adversely affect electronic control systems depending on installation location - Keep the antenna as far as possible from the electronic control units - Keep the antenna feeder line more than 20 cm (8 in) away from the harness of electronic controls Never let them run parallel for a long distance - Adjust the antenna and feeder line so that the standing-wave ratio can be kept smaller - Be sure to ground the radio to vehicle body [VQ35DE] SEF708Y Revision: September 2009 EC-1604 2010 Altima PREPARATION [VQ35DE] < PREPARATION > PREPARATION A PREPARATION Special Service Tools INFOID:0000000005431924 EC The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here Tool number (Kent-Moore No.) Tool name C Description (J-44321) Fuel pressure gauge kit Checks fuel pressure D E LEC642 (J-44321-6) Fuel pressure adapter Connects fuel pressure gauge to quick connector type fuel lines F G H LBIA0376E Commercial Service Tools INFOID:0000000005431925 I Tool name (Kent-Moore No.) Description J (J-45488) Quick connector release Removes fuel tube quick connectors in engine room K L PBIC0198E Leakage detector i.e.: (J-41416) Locates the EVAP leakage M N S-NT703 EVAP service port adapter i.e.: (J-41413-OBD) Applys positive pressure via the EVAP service port O P S-NT704 Revision: September 2009 EC-1605 2010 Altima PREPARATION [VQ35DE] < PREPARATION > Tool name (Kent-Moore No.) Description Fuel filler cap adapter i.e.: (MLR-8382) Checks fuel tank vacuum relief valve opening pressure S-NT815 Socket wrench Removes and installs engine coolant temperature sensor S-NT705 Reconditions the exhaust system threads before installing a new oxygen sensor Use with antiseize lubricant shown below a: 18 mm diameter with pitch 1.5 mm for Zirconia Oxygen Sensor b: 12 mm diameter with pitch 1.25 mm for Titania Oxygen Sensor Oxygen sensor thread cleaner i.e.: (J-43897-18) (J-43897-12) AEM488 Anti-seize lubricant Lubricates oxygen sensor thread cleaning tool when reconditioning exhaust system threads i.e.: (PermatexTM 133AR or equivalent meeting MIL specification MIL-A-907) S-NT779 Revision: September 2009 EC-1606 2010 Altima FUEL PRESSURE [VQ35DE] < ON-VEHICLE MAINTENANCE > ON-VEHICLE MAINTENANCE A FUEL PRESSURE Inspection INFOID:0000000005431926 EC FUEL PRESSURE RELEASE C With CONSULT-III Turn ignition switch ON Perform “FUEL PRESSURE RELEASE” in “WORK SUPPORT” mode with CONSULT-III Start engine After engine stalls, crank it or times to release all fuel pressure Turn ignition switch OFF D E Without CONSULT-III Remove fuel pump fuse (2) located in IPDM E/R (1) • : Vehicle front Start engine After engine stalls, crank it or times to release all fuel pressure Turn ignition switch OFF Reinstall fuel pump fuse after servicing fuel system F G H JMBIA1659ZZ I FUEL PRESSURE CHECK CAUTION: Before disconnecting fuel line, release fuel pressure from fuel line to eliminate danger NOTE: • Prepare pans or saucers under the disconnected fuel line because the fuel may spill out The fuel pressure cannot be completely released because L32 models not have fuel return system • Be careful not to scratch or get the fuel hose connection area dirty when servicing, so that the quick connector o-ring maintains seal ability • Use Fuel Pressure Gauge Kit [SST (J-44321)] and Fuel Pressure Adapter [SST (J-44321-6)] to check fuel pressure Release fuel pressure to zero Remove fuel hose using Quick Connector Release [SST (J-45488)] • Do not twist or kink fuel hose because it is plastic hose • Do not remove fuel hose from quick connector • Keep fuel hose connections clean Install Fuel Pressure Adapter [SST (J-44321-6)] and Fuel Pressure Gauge kit [SST (J44321)] as shown in figure • Do not distort or bend fuel rail tube when installing fuel pressure gauge adapter • When reconnecting fuel hose, check the original fuel hose for damage and abnormality Turn ignition switch ON (reactivate fuel pump) and check for fuel leakage Start engine and check for fuel leakage Read the indication of fuel pressure gauge kit [SST (J-44321)] LBIA0377E • During fuel pressure check, check for fuel leakage from fuel connection every minutes At idling : Approximately 350 kPa (3.57 kg/cm2, 51 psi) Revision: September 2009 EC-1607 2010 Altima J K L M N O P FUEL PRESSURE [VQ35DE] < ON-VEHICLE MAINTENANCE > If result is unsatisfactory, go to next step Check the following • Fuel hoses and fuel tubes for clogging • Fuel filter for clogging • Fuel pump • Fuel pressure regulator for clogging If OK, replace fuel pressure regulator If NG, repair or replace malfunctioning part 10 Before disconnecting Fuel Pressure Gauge kit [SST (J-44321)] and Fuel Pressure Adapter [SST (J44321-6)], release fuel pressure to zero Revision: September 2009 EC-1608 2010 Altima EVAP LEAK CHECK [VQ35DE] < ON-VEHICLE MAINTENANCE > EVAP LEAK CHECK A Inspection INFOID:0000000005431927 CAUTION: EC • Never use compressed air or a high pressure pump • Never exceed 4.12 kPa (0.042 kg/cm2, 0.6 psi) of pressure in EVAP system NOTE: C • Do not start engine • Improper installation of EVAP service port adapter (commercial service tool) to the EVAP service port may cause a leakage D WITH CONSULT-III To locate the EVAP leakage, install EVAP service port adapter (commercial service tool) and pressure pump to EVAP service port Turn ignition switch ON Select the “EVAP SYSTEM CLOSE” of “WORK SUPPORT MODE” with CONSULT-III Touch “START” A bar graph (Pressure indicating display) will appear on the screen Apply positive pressure to the EVAP system until the pressure indicator reaches the middle of the bar graph Remove EVAP service port adapter (commercial service tool) and hose with pressure pump Locate the leakage using a leakage detector (commercial service tool) Refer to EC-1131, "System Diagram" E F G SEF462UA H I J K SEF200U L WITHOUT CONSULT-III To locate the EVAP leakage, install EVAP service port adapter (commercial service tool) and pressure pump to EVAP service port Apply battery voltage between the terminals of EVAP canister vent control valve to make a closed EVAP system To locate the leakage, deliver positive pressure to the EVAP system until pressure gauge points reach 1.38 to 2.76 kPa (0.014 to 0.028 kg/cm2, 0.2 to 0.4 psi) Remove EVAP service port adapter (commercial service tool) and hose with pressure pump M N O SEF462UA P Revision: September 2009 EC-1609 2010 Altima EVAP LEAK CHECK < ON-VEHICLE MAINTENANCE > Locate the leakage using a leakage detector (commercial service tool) Refer to EC-1131, "System Diagram" [VQ35DE] SEF200U Revision: September 2009 EC-1610 2010 Altima EVAP CANISTER [VQ35DE] < ON-VEHICLE REPAIR > ON-VEHICLE REPAIR A EVAP CANISTER Exploded View INFOID:0000000005431928 EC C D E F G AWBIA0671ZZ EVAP control system pressure sensor EVAP canister EVAP canister vent control valve O-ring O-ring H Removal and Installation INFOID:0000000005431929 I REMOVAL Lift up the vehicle Remove EVAP canister fixing bolt Remove EVAP canister NOTE: The EVAP canister vent control valve and EVAP canister system pressure sensor can be removed without removing the EVAP canister INSTALLATION J K Install in the reverse order of removal NOTE: Tighten EVAP canister fixing bolt to the specified torque L DISASSEMBLY M Turn EVAP canister vent control valve counterclockwise N A : Lock B : Unlock O Remove the EVAP canister vent control valve P PBIB3091E ASSEMBLY Assemble in the reverse order of disassembly CAUTION: Always replace O-ring with a new one Revision: September 2009 EC-1611 2010 Altima EVAP CANISTER [VQ35DE] < ON-VEHICLE REPAIR > Inspection INFOID:0000000005431930 Check EVAP canister as per the following: Block port (B) Blow air into port (A) and check that it flows freely out of port (C) Release blocked port (B) Apply vacuum pressure to port (B) and check that vacuum pressure exists at the ports (A) and (C) Block port (A) and (B) Apply pressure to port (C) and check that there is no leakage PBIB1212E Revision: September 2009 EC-1612 2010 Altima SERVICE DATA AND SPECIFICATIONS (SDS) [VQ35DE] < SERVICE DATA AND SPECIFICATIONS (SDS) SERVICE DATA AND SPECIFICATIONS (SDS) A SERVICE DATA AND SPECIFICATIONS (SDS) Idle Speed INFOID:0000000005431931 Transmission Condition Specification CVT No load* (in P or N position) 600 ± 50 rpm M/T No load* (in neutral position) 600 ± 50 rpm *: Under the following conditions EC C D • A/C switch: OFF • Electric load: OFF (Lights, heater fan & rear window defogger) • Steering wheel: Kept in straight-ahead position E Ignition Timing INFOID:0000000005431932 F Transmission Condition Specification CVT No load* (in P or N position) 18 ± 2°BTDC M/T No load* (in neutral position) 18 ± 2°BTDC G *: Under the following conditions • A/C switch: OFF H • Electric load: OFF (Lights, heater fan & rear window defogger) • Steering wheel: Kept in straight-ahead position Calculated Load Value INFOID:0000000005431933 Condition Specification (Using CONSULT-III or GST) At idle 10 – 35 % At 2,500 rpm 10 – 35 % I J K Mass Air Flow Sensor INFOID:0000000005431934 Supply voltage L Battery voltage (11 – 14 V) Output voltage at idle (in N position) 0.9 – 1.2 V* 2.0 – 6.0 g·m/sec at idle* 7.0 – 20.0 g·m/sec at 2,500 rpm* Mass air flow (Using CONSULT-III or GST) M *: Engine is warmed up to normal operating temperature and running under no load N O P Revision: September 2009 EC-1613 2010 Altima