CDMA and cdma2000 for 3G Mobile Networks_5 pdf

an entire cell. Its per-slot data structure is shown in Figure 6-12. Each slot is 2,560 chips long. The spreading factor used on this channel is 128, and a total of only 20 bits is transmitted per slot. However, the transmitter is turned off for the first 256 chips so that the primary and secondary synchronization channels can be transmitted during that period. Eighteen bits of data are then transmitted during the remaining 2,304 chips. Because there are 15 slots in a 10 ms frame, the effective rate on this channel is 27 kb/s. The broadcast channel, which is mapped by this physical channel, uses a fixed, predetermined transport format combination. ■ Secondary Common Control Physical Channel (SCCPCH) This physical channel transmits the information contents of two transport channels — the FACH and the PCH. Unlike the primary common control physical channel, the secondary common control physical channel may be transmitted in a narrow lobe and may use any transport format combination as indicated by the TFCI field. The two transport channels may be mapped either to the same SCCPCH or to two different SCCPCHs. ■ Synchronization Channel (SCH) This channel is used by mobile stations for cell search. There are two synchronization channels — the primary and the secondary. The primary synchronization channel transmits a modulated code, called the primary synchronization code, with a length of 256 chips during the first 256-chip period of each slot of a 10-ms, 15-slot radio frame (refer to Figure 6-12). The PCCPCH is transmitted during the remaining period of each slot. Every cell in a UTRAN uses the same primary synchronization code. Chapter 6 212 256 Chips 2304 Chips Data - 18 bits Transmitter turned off on this channel during this period Figure 6-12 The per-slot data structure for the PCCPCH The secondary SCH is constructed by repeating a sequence of modulated codes of 256 chips and is transmitted in parallel with the primary SCH, that is, on a different physical channel at the same time. There are 64 scrambling code groups for the secondary SCH. ■ Acquisition Indicator Channel (AICH) This downlink channel indicates whether a UE has been able to acquire a PRACH. It operates at a fixed rate with a spreading factor of 128, using a 20 ms frame containing 15 slots, each with a length of 5,120 chips. Each access indicator is 32 bits long and is transmitted during the first 4,096 chips of each slot. Transmission is turned off during the last 1,024 chips so that another channel, such as the common packet channel status indicator channel (CSICH), can be transmitted during this period. See Figure 6-13. ■ Paging Indicator Channel (PICH) This channel is associated with the secondary common control physical channel, uses a spreading factor of 256, and carries 288 bits of paging indication over each 10 ms radio frame. Transmission is turned off during the rest of the frame. 9 213 Universal Mobile Telecommunications System (UMTS) 4096 Chips Status Indicator - 8 bits Transmitter turned off on this channel during this period (equivalent of 32 bits) 0 1o o N o o 14 20 ms Frame Slot # 1024 Chips Figure 6-13 The data structure of the CSICH 9 A 10 ms radio frame with a spreading factor of 256 can carry 300 bits of data. ■ Common Packet Channel (CPCH) Status Indicator Channel (CSICH) As the name implies, this channel carries the CPCH status information. More specifically, the UTRAN uses it to notify the user which slots are available, indicating the data rates supported on those channels. It operates at a fixed rate with a spreading factor of 128. Its data structure is shown in Figure 6-13. This channel is deactivated during the first 4,096 chips so that another channel, such as the acquisition indicator channel (AICH), the CPCH Access Preamble Acquisition Indicator Channel (AP-AICH), or the collision detection/channel assignment indicator channel (CD/CA-ICH) can be activated during the same period. ■ Physical Downlink Shared Channel (PDSCH) This channel, which maps a DSCH transport channel, is always associated with one or more downlink DPCH (that is, downlink dedicated physical channels). It consists of 10 ms frames, each containing 15 slots. The spreading factors used range from 2 to 128. Packet Mode Data It is clear from the previous description that packet mode data from the user plane may be transmitted over a number of chan- nels. If the packets are short and infrequent, they may be trans- mitted over a RACH, CPCH, or FACH rather than a dedicated channel where the associated overhead may be unacceptably high. The RACH and CPCH are multiple-access channels and use the slotted Aloha scheme. If packets are long and relatively more fre- quent, a dedicated channel is established. In this case, after trans- mitting all packets that have arrived at the input, the channel may be either released immediately or held only for a short period thereafter. If there are any new packets during this period, they are transmitted; otherwise, the channel is released at the end of that period. Chapter 6 214 TEAMFLY Team-Fly ® Mapping of Transport Channels to Physical Channels As we indicated in the last section, the physical layer, on receiving the data over a transport channel, transmits it over a radio frame using a particular physical channel. In other words, transport chan- nels are mapped to specific physical channels. This mapping is sum- marized in Figure 6-14. Physical Layer Procedures The standards documents specify procedures for synchronization, power control, accessing common channels, transmit diversity, and the creation of idle periods in the downlink. In this section, we will present a brief description of some of these procedures. 215 Universal Mobile Telecommunications System (UMTS) DCH DPDCH DPCCH BCH PCH FACH RACH CPCH DSCH PCCPCH SCCPCH PRACH PCPCH PDSCH SCH AICH AP-AICH PICH CSICH CD/CA-ICH CPICH Transport Channels Physical Channels Figure 6-14 Mapping of transport channels into physical channels Synchronization Procedures Synchronization procedures include the cell search mechanism and synchronization on the ded- icated channels — the common physical channels as well as the ded- icated physical control and data channels. Cell Search Procedure By cell search, we mean searching for a cell, identifying the downlink scrambling code, achieving the frame syn- chronization, and finding the exact primary scrambling code used in the desired cell. The procedure is outlined in the following steps: 1. Because the primary synchronization code is the same for all cells in a system and is transmitted in every slot of the primary synchronization subchannel, the slot boundaries can be determined by passing the received signal through a filter that is matched to the primary synchronization code and observing the peaks at its output. 2. Notice that it is not possible to identify the frame boundary in step 1. 10 To do this, the received signal is correlated with each of the 64 secondary codes, and the output of the correlator is compared during each slot. The code for which the output is maximum is the desired secondary synchronization code. Similarly, the sequence of 15 consecutive slots over which the correlator output is maximum provides the frame synchronization. 3. The last step is concerned with the determination of the primary scrambling code. Because the common pilot channel is scrambled with the primary scrambling code, the latter can be determined by correlating the received signal over this channel with all codes within the code group determined in step 2. After having found the scrambling code, it is now possible to detect the primary common control physical channel that maps the broadcast channel. Chapter 6 216 10 At this point, only slot boundaries have been found, but we do not know yet which slot belongs to which frame. Synchronization on the Physical Channels Once frame synchroniza- tion has been achieved during the course of the cell search proce- dure, the radio frame timing of all common physical channels is known. Thereafter, layer 1 periodically monitors the radio frames and reports the synchronization status to the higher layers. The status is reported to the higher layers using the following rules: 1. During the first 160 ms following the establishment of a downlink dedicated channel, the signal quality of the DPCCH is measured over the last 40 ms. If this measured signal is better than a specific threshold Q in , the channel is reported to be in sync. At the end of this 160 ms window, go to step 2. 2. Measure the signal quality of the DPCCH over a 160-ms period. Also check transport blocks with attached CRCs. If the signal is less than a threshold Q out , or if the last 20 transport blocks as well as all transport blocks received in the previous 160 ms have incorrect CRCs, declare the channel as out of sync. If, on the other hand, the quality exceeds Q in , and at least one transport block received in the current frame has a correct CRC, the channel is taken to be in sync. Similarly, if the signal exceeds Q in but no transport blocks or no transport blocks with a CRC are received, the status is taken to be in sync. Setting Up a Radio Link When setting up a radio link, there are two cases to consider depending on whether or not there already exists a radio link for the UE: ■ To establish a radio link when there are none initially, the UTRAN starts transmitting on a downlink DPCCH. If there is any user data to send, it may also start transmitting that data on a downlink DPCCH. 11 The UE monitors the downlink DPCCH and first establishes frame synchronization using a PCCPCH. Thereupon, it can begin 217 Universal Mobile Telecommunications System (UMTS) 11 Recall that the downlink DPCCH and the downlink DPDCH are time-division mul- tiplexed. to transmit on the uplink DPCCH either immediately or, if necessary, after a delay of a specified activation time following the successful establishment of the downlink channel. Transmission on the uplink DPDCH can start only after the end of the power control preamble. The base transceiver station monitors the uplink DPCCH and establishes chip and frame synchronization on that channel. Once the higher layers in the UTRAN have determined that the link is in sync, the radio link is considered established. ■ To set up a radio link when there are other radio links already established, the UTRAN begins to transmit on a new downlink DPCCH and, if necessary, on a new downlink DPDCH with appropriate frame timing. The UE monitors the new downlink DPCCH, establishes frame synchronization on this channel, begins to transmit on an uplink DPCCH, and, if necessary, on an uplink DPDCH as well. The base transceiver station monitors the uplink DPCCH and establishes chip and frame synchronization on that channel. Once the higher layers in the UTRAN have determined that the link is in sync, the new radio link is considered established. It is possible that the receive timing of a downlink DPCH may drift significantly over time so that the time difference between downlink and uplink frames exceeds the permissible value. When this is the case, the physical layer reports the event to higher layers so that the network can be requested to adjust its timing. Power Control As we mentioned, power control is an important feature of a CDMA system. Its objective is to ensure a satisfactory signal-to-interference ratio at the receiver for all links in the sys- tem. In UMTS, different power control procedures are used for uplink and downlink physical channels. Because our goal is to acquaint the reader with the general concept of the power control in UMTS, we will briefly describe only some of these procedures [12]. First, however, definitions of a few terms are in order. Chapter 6 218 Open Loop Power Control This is a process by which the UE sets its transmitter power output to any specific level. The open loop power control tolerance is Ϯ9 dB under normal conditions and Ϯ12 dB under extreme conditions. Inner Loop Power Control in the Downlink This procedure enables a base station to adjust its transmit power in response to TPC commands from the UE. Power is adjusted using a step size of 0.5 or 1 dB. The objective here is to maintain a satisfactory signal-to-interference ratio at a UE using as little base station transmitter signal power as possible. Inner Loop Power Control in the Uplink This procedure is used by the UE to adjust its transmit power in response to a TPC command from a base station. With each TPC command, the UE transmit power is adjusted in steps of 1, 2, or 3 dB in the slot immediately following the decoding of TPC commands. A TPC command may be either 0 or 1. If it is 0, it means that the transmitter power has to be decreased. If it is 1, the transmitter power is to be increased. Uplink Inner Loop Power Control Procedure on Dedicated Physical Chan- nels The dedicated physical channels use the uplink inner loop power control. Briefly, the procedure is as follows. The UE starts transmitting on the uplink DPCCH at a power level that is initially set by the higher layers. Serving cells measure the received SIR and compare it with a target threshold. If the measured SIR exceeds the threshold, the UTRAN sends a TPC command 0, indicating that the mobile station should decrease its power level using a step size of 1 or 2 dB as specified by the higher layers. If the measured SIR is less than the threshold, TPC command 1 is transmitted, requiring the mobile to increase its power level. If both data and control channels are active at the same time, the power level of both uplink channels is changed simultaneously by the same amount. For a DPCCH, this change should be affected at the beginning of the uplink DPCCH pilot field immediately following the TPC command on the downlink 219 Universal Mobile Telecommunications System (UMTS) channel. This is shown in Figure 6-15. Notice the timing offset between the downlink DPCH and the uplink DPCCH. It is also worth mentioning that the TPC command on the uplink starts 512 chips after the end of the pilot field on the downlink channel. When a mobile station is being served by a single cell and is not in a soft handoff state, it receives only one TPC command in each slot. Because there are 15 slots in a radio frame and each frame is 10 ms long, it may receive 1,500 TPC commands per second. However, if the mobile is in a soft handoff state, more than one TPC command may be received in each slot of a radio frame from cells in an active set that participate in the handoff process. The physical layer parses these commands, and if it finds all TPC com- mands to be 1, it increases the transmitter power by the selected step size. Similarly, if all commands are 0, the power is decreased by the same amount. Otherwise, if the commands are all random and uncorrelated, they are interpreted based on a probabilistic model [12]. The same procedure is used to adjust the power level during the uplink DPCCH power control preamble. 12 The procedure that we have just described adjusts the power level in accordance with the TPC commands received during each slot, Chapter 6 220 Pilot PilotData 1 TPC TFCI Data 2 Data TFCI Slot N+1 TPC Slot N Slot N-1 Downlink DPCH Slot NSlot N-1 Slot N+1 Uplink DPCCH Pilot TFCI TPC Pilot TFCI TPC Timing offset between UL and DL - 1024 chips UTRAN measures this signal 512 chips UTRAN sends this TPC command Pilot UE gets this TPC command and sets uplink DPCH power at start of this field DPDCH DPCCH DPDCH DPCCH Figure 6-15 The sequence of events and their timing during the uplink power control 12 The transmission on a DPDCH starts only after the end of this preamble. using a step size of 1 or 2 dB. This is referred to in the standards doc- ument as Algorithm 1. Using a slight variation of this algorithm, we can emulate a smaller step size and thus effect a finer adjustment. This is called Algorithm 2, which is briefly described here. Assume that the mobile is being served by a single cell and is not going through any handoff process. For each set of five slots aligned to the frame boundaries, no action is taken on those commands that were received in the first four slots. During the fifth slot, the receiver determines if the TPC commands in all of these five slots are the same. If they are, the power level is increased or decreased by the previous step size, depending on whether they are all 1 or 0. Other- wise, the commands are ignored. Because the power level is now being changed by the same amount every five slots, the net result is the equivalent of a smaller step size. The procedure to emulate a smaller step size when the mobile is undergoing a handoff process is similar. Downlink Inner Loop Power Control on DPCCH and DPDCH The oper- ation of the downlink inner loop power control is quite similar. Assuming that the mobile is being served by a single cell and is not going through a handoff process, the UE measures the SIR on the downlink physical channels and compares it with a desired target value. If the measured SIR is less, the UE sets the TPC command to 1 in the next available TPC field of the uplink DPCCH. The UTRAN responds by increasing the power of the downlink DPCH at the beginning of the next pilot field on that channel following the TPC command on the uplink. If the measured SIR is more than the desired value, a TPC com- mand 0 is sent in the next available TPC field of the uplink DPCCH, thus requesting a reduced power level. In response, the UTRAN decreases the power level of the downlink DPCH at the beginning of the next pilot field on that channel following the TPC command on the uplink. The downlink power control timing is shown in Figure 6-16. Depending on the downlink power control mode, the UE may send either a unique TPC command in each slot or the same command over three slots while making sure that a new command appears at the beginning of a radio frame. On receiving a TPC command, the 221 Universal Mobile Telecommunications System (UMTS) [...]... command, and 010 for RESET ACK Its other possible values are reserved Superfields (SUF) are actually variable-length information elements of the STATUS PDU and perform many functions For exam- Figure 6-28 The RLC PDU format for the acknowledged mode D/C Sequence No Sequence No P Octet 1 HE Octet 2 Length Indicator E Octet 3 Length Indicator E Octet 4 o Data Pad or Piggy-backed Status o Universal Mobile. .. said before, it is used only in the acknowledged transfer mode and may be sent either as a completely separate PDU or as part of the data PDU in a piggyback fashion Its format, when sent separately, is depicted in Figure 6-29 The one-bit D/C field distinguishes the control PDU from the data PDU—it is 0 for the former and 1 for the latter The 3-bit PDU type field is 000 for a STATUS PDU, 001 for a RESET... synchronization channel, is converted into parallel form and separated into two streams, one with the odd bits and the other with the even bits Each of these streams is spread by a channel-specific, orthogonal spreading code shown as C1 in this figure The spreading factor is 256 for common downlink physical channels and varies from 4 to 512 for a downlink DPCH The I and Q channels are added in quadrature, scrambled... the UE can perform these measurements is called the compressed mode Measurements may be divided into a few types: I Measurements on downlink physical channels These measurements may involve a single W -CDMA frequency, Universal Mobile Telecommunications System (UMTS) 231 different W -CDMA frequencies (such as when a UE is near the boundary of two W -CDMA systems), or a W -CDMA frequency and the operating... and connection frame number (CFN) in the UE It is given in terms of chips for the FDD mode and frame numbers for the TDD mode I Difference between the timing of a given UTRA and the timing of a GSM cell I Ec/N0 for the common pilot channel (CPICH), where Ec is the received energy per chip and N0 the noise power density I SIR for CPICH I Received signal code power on the PCCPCH after despreading I Interference... general format of the MAC PDU is presented in Figure 6-24 There are four fields in the header The first field called the Target Channel Type Field (TCTF) indicates the logical channel and may be 1, 2, 3, 4, 5, or 8 bits long depending upon the associated transport channel and the mode (that is, FDD or TDD) For example, on a RACH in the FDD mode, this field is 00 for a common control channel and 01 for. .. Figure 6-16 The sequence of events and their timing during the downlink power control Downlink DPCCH Slot N Pilot UE measures SIR on this pilot and sends this TPC command Uplink DPCCH Pilot Data TPC TFCI Timing offset between UL and DL - 1024 chips 512 chips TFCI Slot N-1 TPC Slot N+1 Data Pilot Data TPC TFCI UTRAN gets this TPC command and changes power immediately before the start of this pilot Pilot... access the random access physical channel Randomly select an access slot and a signature Set the preamble retransmission counter to the maximum permissible value Set the commanded preamble power to initial value Make sure the commanded preamble power is within permissible range Transmit preamble on selected slot with signature and power No Acquisition Indicator? Select next available access slot, randomly... higher channel bandwidths and decrease the transmission efficiency but also increase the delay Compression algorithms are based on the fact that many of the header fields remain the same during the life of a call and do no change from one packet to another For example, most of the fields of an IP header remain constant Similarly, with TCP and UDP, the source and destination address and port numbers... period as well as the location of the schedule message for the following period The BMC layer, on the UE side, determines which messages to forward to its upper layer and sends an indication to the RRC layer The BMC message format is very similar to that of an ISDN call control message and consists of a number of information elements As an example, the information elements of a cell broadcast message are . TPC Timing offset between UL and DL - 1024 chips UE measures SIR on this pilot and sends this TPC command 51 2 chips UTRAN gets this TPC command and changes power immediately before the start of this. channel. When a mobile station is being served by a single cell and is not in a soft handoff state, it receives only one TPC command in each slot. Because there are 15 slots in a radio frame and each. shown as C 1 in this figure. The spreading factor is 256 for common downlink physical channels and varies from 4 to 51 2 for a downlink DPCH. The I and Q channels are added in quadrature, scrambled