BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 Incorporating corrigenda September 2012 and October2012 2014 Incorporating corrigendum September 2012 Incorporating corrigendum September BSI Standards Publication Plugs, socket-outlets, vehicle connectors and vehicle inlets — Conductive charging of electric vehicles Part 2: Dimensional compatibility and interchangeability requirements for a.c pin and contact-tube accessories BS EN 62196-2:2012+A12:2014 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 62196-2:2012+A12:2014, incorporating corrigendum October 2014 It is identical to IEC 62196-2:2011 It supersedes BS EN 62196-2:2012+A11:2013, which will be withdrawn on 16 June 2017 Where a common modification has been introduced by amendment, the tags carry the number of the amendment For example, the common modifications introduced by CENELEC amendment A11 are indicated by The UK participation in its preparation was entrusted by Technical Committee PEL/23, Electrical accessories, to Subcommittee PEL/23/4, Protected type plugs and sockets A list of organizations represented on this subcommittee can be obtained on request to its secretary This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application © The British Standards Institution 2014 Published by BSI Standards Limited 2014 ISBN 978 580 88428 ICS 29.120.30; 43.120 Compliance with a British Standard cannot confer immunity from legal obligations This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2012 Amendments/corrigenda issued since publication Date Text affected 30 September 2012 Inserted missing pages (pp.23-63) 30 June 2013 Implementation of CENELEC amendment A11:2013 30 September 2014 Implementation of CENELEC amendment A12:2014: STANDARD SHEET 2-IIa (Sheet 1) and STANDARD SHEET 2-IIa (Sheet 2) updated 30 November 2014 Implementation of CENELEC corrigendum October 2014: STANDARD SHEET 2-IIa (Sheet 1) replaced EN EN 62196-2:2012+A11 EN62196-2:2012+A12 62196-2 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM August 2014 May2013 2012 April Incorporating corrigendum October 2014 ICS 29.120.30; 43.120 English version Plugs, socket-outlets, vehicle connectors and vehicle inlets Conductive charging of electric vehicles Part 2: Dimensional compatibility and interchangeability requirements for a.c pin and contact-tube accessories (IEC 62196-2:2011) Fiches, socles de prise de courant, prises mobiles et socles de connecteurs de véhicule Charge conductive des véhicules électriques Partie 2: Exigences dimensionnelles de compatibilité et d’interchangeabilité pour les appareils broches et alvéoles pour courant alternatif (CEI 62196-2:2011) Stecker, Steckdosen, Fahrzeugkupplungen und Fahrzeugstecker Konduktives Laden von Elektrofahrzeugen Teil 2: Anforderungen und Hauptmaße für die Kompatibilität und Austauschbarkeit von Stift- und Buchsensteckvorrichtungen für Wechselstrom (IEC 62196-2:2011) This European Standard was approved by CENELEC on 2012-02-01 CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels © 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members Ref No EN 62196-2:2012 E BS EN 62196-2:2012 62196-2:2012+A12:2014 BS EN 62196-2:2012 62196-2:2012+A11:2013 EN 62196-2:2012 BS EN 62196-2:2012 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012 BS EN 62196-2:2012 EN 62196-2:2012 EN 62196-2:2012 -2-––22- –– -2-2- Foreword Foreword Foreword The text of document 23H/267/FDIS, future edition of IEC 62196-2, prepared by SC 23H, "Industrial Foreword The text document 23H/267/FDIS, future edition 1accessories" of IEC 62196-2, prepared by "Industrial plugs andof of IEC TC 23, "Electrical was submitted to SC the 23H, IEC-CENELEC The text ofsocket-outlets", document 23H/267/FDIS, future edition of IEC 62196-2, prepared by SC 23H, "Industrial plugs and socket-outlets", of IEC TC 23, "Electrical accessories" was submitted to the IEC-CENELEC The ofsocket-outlets", document 23H/267/FDIS, future edition 1accessories" of IEC 62196-2, prepared by "Industrial parallel vote and approved by as EN 62196-2:2012 plugstext and of CENELEC IEC TC 23, "Electrical was submitted to SC the 23H, IEC-CENELEC parallel votesocket-outlets", and approved by CENELEC as EN 62196-2:2012 plugs and of IEC TC 23, "Electrical accessories" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62196-2:2012 parallel vote and approved by CENELEC as EN 62196-2:2012 The following dates are fixed: The following dates are fixed: The following dates are fixed: The following are fixed: (dop) 2012-11-01 • latest datedates by which the document has (dop) 2012-11-01 • to latest date by which the document be implemented national levelhas by (dop) 2012-11-01 • latest date by whichatthe document has be implemented at national level by (dop) 2012-11-01 • to latest date by which the document has publication of an identical national to be implemented at national level by publication of an identical national to be implemented at national level by standard orof byan endorsement publication identical national byan endorsement publication of identical national (dow) 2015-02-01 • standard latest dateor the national standard orby bywhich endorsement (dow) 2015-02-01 • standard latest dateorconflicting by which the national by endorsement standards with the (dow) 2015-02-01 • latest date by which the national standards conflicting with the (dow) 2015-02-01 • document latest date conflicting by which national have to bethe withdrawn standards with the document have to be with withdrawn standards conflicting the document have to be withdrawn document have to be withdrawn EN 62196-2 is to be read in conjunction with EN 62196-1 The clauses of the particular requirements in EN 62196-2 is to be in the conjunction with EN 62196-1 The1.clauses of the in Part supplement or read modify corresponding clauses in Part Where the textparticular indicates requirements an "addition" to EN 62196-2 is to be read in conjunction with EN 62196-1 The clauses of the particular requirements in Part supplement or modify the corresponding clauses in Part Where the text indicates an "addition" to EN is to be in the conjunction with EN 62196-1 The1.clauses of the in or a62196-2 "replacement" of read the relevant requirement, test specification or explanation of Part 1,requirements these changes Part supplement or modify corresponding clauses in Part Where the textparticular indicates an "addition" to or "replacement" of modify the relevant requirement, test specification or of explanation Part 1, an these changes Part supplement or in Part Where text of indicates "addition" to area to the relevant textthe ofcorresponding Part 1, which clauses then becomes part thethe standard Where no change is or a made "replacement" of the relevant requirement, test specification or explanation of Part 1, these changes are made to the relevant text of Part 1, which then becomes part of the standard Where no change is or a "replacement" of the relevant requirement, test specification or explanation of Part 1, these changes necessary, words "Thistext clause of Part is applicable" are used are made tothe the relevant of Part 1, which then becomes part of the standard Where no change is necessary, the words "Thistext clause of Part is applicable" are used are made to the relevant of Part 1, which then becomes part of the standard Where no change is necessary, the words "This clause of Part is applicable" are used This standard the Principle the Safetyare Objectives for Electrical Equipment Designed necessary, thecovers words "This clause ofElements Part is of applicable" used This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed for Use within Certain Voltage Limits (LVD 2006/95/EC) This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed for Use within Certain Voltage LimitsElements (LVD - 2006/95/EC) This standard covers the Principle of the Safety Objectives for Electrical Equipment Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC) for Use within Certain Voltage Limits (LVD 2006/95/EC) Attention is drawn to the possibility that some of the elements of this document may be the subject of Attention is drawn to the[and/or possibility that some elements of this beall the subject of patent rights CENELEC CEN] shall not of bethe held responsible for document identifying may any or patent Attention is drawn to the possibility that some of the elements of this document may be thesuch subject of patent rights CENELEC [and/or CEN] shall not of bethe held responsible for document identifying may any or all such patent Attention is drawn to the possibility that some elements of this be the subject of rights patent rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights patent rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights rights Endorsement notice Endorsement notice Endorsement notice EN 62196-2:2012/A11:2013 –2– The text of the International StandardEndorsement IEC 62196-2:2011notice was approved by CENELEC as a European The text of the International Standard IEC 62196-2:2011 was approved by CENELEC as a European Standard without any modification The text of the International Standard IEC 62196-2:2011 was approved by CENELEC as a European Standard without any modification The text of the International Standard IEC 62196-2:2011 was approved by CENELEC as a European Standard without any modification Standard without any modification ForewordForeword to amendment A11 This document (EN 62196-2:2012/A11:2013) has been prepared by CLC/TC 23BX "Switches, boxes and enclosures for household and similar purposes, plugs and socket outlets for d.c and for the charging of electrical vehicles including their connectors" The following dates are fixed: • latest date by which this document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2013-10-15 • latest date by which the national standards conflicting with this document have to be withdrawn (dow) 2017-10-15 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights This document has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC) EN 62196-2:2012/A12:2014 –3– -2- BS EN 62196-2:2012+A12:2014 EN 62196-2:2012+A12:2014 Foreword Foreword to amendment A12 This document (EN 62196-2:2012/A12:2014) has been prepared by CLC/TC 23BX "Switches, boxes and enclosures for household and similar purposes, plugs and socket outlets for d.c and for the charging of electrical vehicles including their connectors" The following dates are fixed: • • latest date by which this document has to be implemented at national level by publication of an identical national standard or by endorsement latest date by which the national standards conflicting with this document have to be withdrawn (dop) 2015-06-16 (dow) 2017-06-16 This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights BS EN 62196-2:2012+A12:2014 EN 62196-2:2012+A12:2014 –4 –– -3- BS EN 62196-2:2012+A11:2013 EN 62196-2:2012+A11:2013 BS EN 62196-2:2012 EN 62196-2:2012 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies Addition to Annex ZA of EN 62196-1:2012: Publication Year Title EN/HD Year IEC 60068-2-14 - Environmental testing Part 2-14: Tests - Test N: Change of temperature EN 60068-2-14 - BS EN 62196-2:2012+A11:2013 EN 62196-2:2012+A11:2013 EN 62196-2:2012/A11:2013 5– –– –4– BS EN 62196-2:2012+A12:2014 EN 62196-2:2012+A12:2014 Annex ZB (normative) Special national conditions Special national condition: National characteristic or practice that cannot be changed even over a long period, e.g climatic conditions, electrical earthing conditions NOTE If it affects harmonization, it forms part of the European Standard / Harmonization Document For the countries in which the relevant special national conditions apply these provisions are normative, for other countries they are informative Clause Special national condition 6.1 United Kingdom Mode will not be used in the United Kingdom 10.101 France nd Add a paragraph: When plugs & socket-outlets are used and socket-outlets are accessible to uninstructed persons, they shall be provided with shutters (as presently defined in Type 3) 10.101 Portugal Shutters are compulsory on live (phase and neutral) contact holes of socket-outlets and connectors not exceeding 16 A when these accessories are accessible to uninstructed persons (ordinary persons BA1, handicapped persons BA2 or children BA3) In locations with restricted access to skilled persons, socket-outlets and connectors without shutters may be accepted. BS EN 62196-2:2012+A12:2014 EN 62196-2:2012+A12:2014 –5– –6 –– –2– –2– BS EN 62196-2:2012+A11:2013 BS EN EN 62196-2:2012+A11:2013 62196-2:2012+A11:2013 BS EN 62196-2:2012 EN 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC:2011 62196-2 IEC:2011 CONTENTS CONTENTS FOREWORD FOREWORD INTRODUCTION 9 INTRODUCTION 10 Scope 10 Scope Normative references 10 11 Normative Terms and references definitions 11 Terms definitions .10 Generaland 11 General 10 Ratings 11 Ratings Connection between the power supply and the electric vehicle 10 13 Connection between the power supply and the electric vehicle 14 Classification of accessories 11 13 Classification of accessories 14 11 Marking 13 Marking 11 Dimensions 14 11 10 Dimensions Protection against electric shock 14 12 15 14 10 against 11 Protection Size and colour of electric earthingshock conductors 15 12 14 11 and colour of earthing conductors 15 12 Size Provision for earthing 12 14 12 earthing 15 12 13 Provision Terminals for 13 12 16 14 Terminals Interlocks 15 13 15 14 13 15 Interlocks Resistance to ageing of rubber and thermoplastic material 16 15 15 to ageing of rubber and thermoplastic material 16 16 Resistance General construction 13 15 16 construction 13 17 General Construction of socket-outlets 16 15 17 18 Construction of socket-outlets plugs and vehicle connectors 16 13 15 18 plugs and vehicle connectors 16 13 19 Construction of vehicle inlets 15 19 of vehicle inlets 16 13 20 Construction Degrees of protection 15 20 protectionand 21 Degrees Insulationofresistance dielectric strength 16 13 15 21 resistance and dielectric strength 16 22 Insulation Breaking capacity 13 17 22 capacity 16 13 23 Breaking Normal operation 14 16 23 operation 24 Normal Temperature rise 17 14 16 24 rise 25 Temperature Flexible cables and their connection 17 14 16 25 cables and their connection 17 14 26 Flexible Mechanical strength 18 26 strength 14 27 Mechanical Screws, current-carrying parts and connections 17 15 17 27 current-carrying parts and connections 15 28 Screws, Creepage distances, clearances and distances 18 17 28 distances 18 29 Creepage Resistancedistances, to heat, toclearances fire and to and tracking 15 17 29 to heat, to fireto and to tracking 18 15 30 Resistance Corrosion and resistance rusting 17 30 resistancecurrent to rusting 31 Corrosion Conditionaland short-circuit withstand test 18 15 17 31 short-circuit current withstand test 18 32 Conditional Electromagnetic compatibility (EMC) 15 17 32 (EMC) 18 33 Electromagnetic Vehicle driveovercompatibility 15 17 33 driveover 18 101 Vehicle Components 15 19 101 15 102 Components Coding resistors 18 16 102 Coding resistors 19 16 Table 101 – Overview of the basic vehicle interface, configuration Type 1, single 12 13 phase 10 Table 101 – Overview of the basic vehicle interface, configuration Type 1, single phase 13 10 BS EN 62196-2:2012+A11:2013 EN 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC:2011 7– –– BS EN 62196-2:2012+A12:2014 EN 62196-2:2012+A12:2014 –3– Table 102 – Overview of the basic vehicle interface, configuration Types and 3, 12 three-phase or single phase 13 10 14 Table 103 – Configuration types and standard sheets 15 12 BS EN 62196-2:2012+A12:2014 EN 62196-2:2012+A12:2014 –8 –– –6– BS EN 62196-2:2012+A11:2013 EN 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC:2011 INTRODUCTION Responding to global challenges of CO reduction and energy security, the automobile industries have been accelerating the development and commercialization of electric vehicles and hybrid electric vehicles In addition to the prevailing hybrid electric vehicles, battery electric vehicles including plug-in hybrid electric vehicles are going to be mass-marketed To support the diffusion of such vehicles, this standard provides the standard interface configurations of a.c vehicle couplers and accessories to be used in conductive charging of electric vehicles, taking the most frequent charging situations into consideration IEC 62196 is divided into several parts: Part 1: General requirements Part 2: Dimensional compatibility and interchangeability requirements for a.c pin and contacttube accessories Part 3: Dimensional compatibility and interchangeability requirements for pin and contact-tube accessories for dedicated d.c charging or for combined a.c./d.c.charging (under consideration) BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC/CEI:2011 –– 50 –– – 63 47 – STANDARD SHEET 2-IIIa (Sheet 4) FEUILLE DE NORME 2-IIIa (Feuille 4) VEHICLE CONNECTOR NOT EXCEEDING 250 V, 16 A SINGLE PHASE WITH PILOT CONTACT PRISE MOBILE DE VÉHICULE NE DEPASSANT PAS 250 V, 16 A EN MONOPHASÉ AVEC CONTACT PILOTE (continuation of Sheet 3) (suite de la feuille 3) IEC 2317/11 –– 51 –– – 64 48 – BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC/CEI:2011 STANDARD SHEET 2-IIIb (Sheet 1) FEUILLE DE NORME 2-IIIb (Feuille 1) PLUG NOT EXCEEDING 250V, 32 A SINGLE PHASE WITH PILOT CONTACTS FICHE NE DEPASSANT PAS 250 V, 32 A EN MONOPHASÉ AVEC CONTACTS PILOTES IEC 2318/11 BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC/CEI:2011 –– 52 –– – 65 49 – STANDARD SHEET 2-IIIb (Sheet 2) FEUILLE DE NORME 2-IIIb (Feuille 2) SOCKET-OUTLET NOT EXCEEDING 250 V, 32 A SINGLE PHASE WITH PILOT CONTACTS SOCLE DE PRISE NE DEPASSANT PAS 250 V, 32 A EN MONOPHASÉ AVEC CONTACTS PILOTES (continuation of Sheet 1) (suite de la feuille 1) IEC 2319/11 –– 53 –– – 66 50 – BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC/CEI:2011 STANDARD SHEET 2-IIIb (Sheet 3) FEUILLE DE NORME 2-IIIb (Feuille 3) VEHICLE INLET NOT EXCEEDING 250 V, 32 A SINGLE PHASE WITH PILOT CONTACTS SOCLE DE CONNECTEUR DE VÉHICULE NE DEPASSANT PAS 250 V, 32 A EN MONOPHASÉ AVEC CONTACTS PILOTES (continuation of Sheet 2) (suite de la feuille 2) IEC 2320/11 BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC/CEI:2011 –– 54 –– – 67 51 – STANDARD SHEET 2-IIIb (Sheet 4) FEUILLE DE NORME 2-IIIb (Feuille 4) VEHICLE CONNECTOR NOT EXCEEDING 250 V, 32 A SINGLE PHASE WITH PILOT CONTACTS PRISE MOBILE DE VÉHICULE NE DEPASSANT PAS 250 V, 32 A EN MONOPHASÉ AVEC CONTACTS PILOTES (continuation of Sheet 3) (suite de la feuille 3) IEC 2321/11 –– 55 –– – 68 52 – BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC/CEI:2011 STANDARD SHEET 2-IIIc (Sheet 1) FEUILLE DE NORME 2-IIIc (Feuille 1) PLUG NOT EXCEEDING 480 V, 63 A THREEPHASE WITH PILOT CONTACTS FICHE NE DEPASSANT PAS 480 V, 63 A EN TRIPHASÉ AVEC CONTACTS PILOTES IEC 2322/11 BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC/CEI:2011 –– 56 –– – 69 53 – STANDARD SHEET 2-IIIc (Sheet 2) FEUILLE DE NORME 2-IIIc (Feuille 2) SOCKET-OUTLET NOT EXCEEDING 480 V, 63 A THREE-PHASE WITH PILOT CONTACTS SOCLE DE PRISE NE DEPASSANT PAS 480 V, 63 A EN TRIPHASÉ AVEC CONTACTS PILOTES (continuation of Sheet 1) (suite de la feuille 1) IEC 2323/11 –– 57 –– – 70 54 – BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC/CEI:2011 STANDARD SHEET 2-IIIc (Sheet 3) FEUILLE DE NORME 2-IIIc (Feuille 3) VEHICLE INLET NOT EXCEEDING 480 V, 63 A THREE-PHASE WITH PILOT CONTACTS SOCLE DE CONNECTEUR DE VÉHICULE NE DEPASSANT PAS 480 V, 63 A TRIPHASÉ AVEC CONTACTS PILOTES (continuation of Sheet 2) (suite de la feuille 2) IEC 2324/11 BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC/CEI:2011 –– 58 –– – 71 55 – STANDARD SHEET 2-IIIc (Sheet 4) FEUILLE DE NORME 2-IIIc (Feuille 4) VEHICLE CONNECTOR NOT EXCEEDING 480 V, 63 A THREE-PHASE WITH PILOT CONTACTS PRISE MOBILE DE VÉHICULE NE DEPASSANT PAS 480 V, 63 A EN TRIPHASÉ AVEC CONTACTS PILOTES (continuation of Sheet 3) (suite de la feuille 3) IEC 2325/11 –– 59 –– – 72 56 – BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC/CEI:2011 STANDARD SHEET 2-IIId (Sheet 1) FEUILLE DE NORME 2-IIId (Feuille 1) RETAINING MEANS AND PACKAGING ROOM FOR 2P+E+ PILOT 16 A 250 V (STANDARD SHEET 2-IIIa) DISPOSITIF DE RETENUE ET VOLUME ENVELOPPE POUR 2P+T+ PILOT 16 A 250 V (FEUILLE DE NORME 2-IIIa) IEC 2326/11 BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC/CEI:2011 –– 60 –– – 73 57 – STANDARD SHEET 2-IIId (Sheet 2) FEUILLE DE NORME 2-IIId (Feuille 2) RETAINING MEANS AND PACKAGING ROOM FOR 2P+E+ PILOTS 32 A 250 V (STANDARD SHEET 2-IIIb) DISPOSITIF DE RETENUE ET VOLUME ENVELOPPE POUR 2P+T+ PILOTES 32 A 250 V (FEUILLE DE NORME 2-IIIb) (continuation of Sheet 1) (suite de la feuille 1) IEC 2327/11 –– 61 –– – 74 58 – BS EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 EN 62196-2:2012+A12:2014 62196-2:2012+A11:2013 BS EN 62196-2:2012 62196-2 IEC/CEI:2011 STANDARD SHEET 2-IIId (Sheet 3) FEUILLE DE NORME 2-IIId (Feuille 3) RETAINING MEANS AND PACKAGING ROOM FOR 2P+E+ PILOTS 63 A 480 V (STANDARD SHEET 2-IIIc) DISPOSITIF DE RETENUE ET VOLUME ENVELOPPE POUR 2P+T+ PILOTES 63 A 480 V (FEUILLE DE NORME 2-IIIc) (continuation of Sheet 2) (suite de la feuille 2) IEC 2328/11 This page deliberately left blank This page deliberately left blank NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards Institution (BSI) BSI is the national body responsible for preparing British Standards and other standards-related publications, information and services BSI is incorporated by Royal Charter British Standards and other standardization products are published by BSI Standards Limited About us Revisions We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions Our British Standards and other publications are updated by amendment or revision The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process Organizations of all sizes and across all sectors choose standards to help them achieve their goals Information on standards We can provide you with the knowledge that your organization needs to succeed Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop, where hard copies can also be purchased If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team Subscriptions Our range of subscription services are designed to make using standards easier for you For further information on our subscription products go to bsigroup.com/subscriptions With British Standards Online (BSOL) you’ll have instant access to over 55,000 British and adopted European and international standards from your desktop It’s available 24/7 and is refreshed daily so you’ll always be up to date You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member PLUS is an updating service exclusive to BSI Subscribing Members You will automatically receive the latest hard copy of your standards when they’re revised or replaced To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit bsigroup.com/shop With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet Licences can cover as few or as many users as you wish With updates supplied as soon as they’re available, you can be sure your documentation is current For further information, email bsmusales@bsigroup.com BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK We continually improve the quality of our products and services to benefit your business If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI Details and advice can be obtained from the Copyright & Licensing Department Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): orders@bsigroup.com Email (enquiries): cservices@bsigroup.com Subscriptions Tel: +44 845 086 9001 Email: subscriptions@bsigroup.com Knowledge Centre Tel: +44 20 8996 7004 Email: knowledgecentre@bsigroup.com Copyright & Licensing Tel: +44 20 8996 7070 Email: copyright@bsigroup.com