BRITISH STANDARD Miscellaneous lamps ICS 29.140.20; 29.140.30 BS EN EN 61549:2003 61549:2003 +A3:2012 +A2:2010 BS EN 61549:2003+A2:2010 BS EN 61549:2003+A3:2012 National foreword National foreword This British Standard is the UK implementation of This British Standard is the implementation of EN 61549:2003+A3:2012 EN 61549:2003+A2:2010 It UK is identical to IEC 61549:2003, including It is identical to IEC 61549:2003, 3:2012 It amendments 1:2005 and 2:2010 incorporating It supersedesamendment BS EN 61549:2003 supersedes BS EN 61549:2003+A2:2010 which is withdrawn which is withdrawn The amendment by which each page of the European standard was introduced is indicated by an extension to the shoulder heading at the top of the page (e.g EN 61549:2003/A2:2010) Where no such extension appears, the page is part of the original European standard UK participation participationininits itspreparation preparation was entrusted Technical The UK was entrusted by by Technical Committee CPL/34, CP/34, Lamps Committee Lamps and and related Related equipment, Equipment,to to Subcommittee Subcommittee CPL/34/1, Electric Electriclamps lamps CPL/34/1, A list of organizations represented on this subcommittee can be obtained on request to its secretary This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application Compliance with a British Standard cannot confer immunity from legal obligations This British Standard was published under the authority of the Standards Policy and Strategy Committee on 24 July 2003 Standard was This British published under the authority of the Standards Policy and Committee on ©Strategy BSI 2010 24 July 2003 © The British Standards Institution 2012 Published by BSI Standards Limited 2012 ISBN 978 580 72085 ISBN 978 580 75785 Amendments/corrigenda issued since publication Amd No Date Comments Amendments/corrigenda issued since publication 15781 31 August Implementation of IEC amendment 1:2005 with CENELEC endorsement A1:2005 Amd No Date Comments 31 July 2010 Implementation of IEC amendment 2:2010 15781 31 August Implementation of IEC amendment 1:2005 with CENELEC endorsement A2:2010 with CENELEC endorsement A1:2005 31 July 2010 Implementation of IEC amendment 2:2010 with CENELEC endorsement A2:2010 31 January 2013 Implementation of IEC amendment 3:2012 with CENELEC endorsement A3:2012 EUROPEAN STANDARD NORME EUROPÉENNE EN 61549 :2003+A2 61549:2003+A3 May 2010 October 2012 EUROPÄISCHE NORM ICS 29.140.20; 29.140.30 Supersedes EN 61549:1996 + A1:1997 + A2:2001 English version Miscellaneous lamps (IEC 61549:2003) Lampes diverses (CEI 61549:2003) Sonderlampen (IEC 61549:2003) This European Standard was approved by CENELEC on 2003-06-01 CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels © 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members Ref No EN 61549:2003 E Page Page BS EN 61549:2003+A3:2012 BS EN 61549:2003+A2:2010 EN 61549:2003+A3:2012 EN 61549:2003+A2:2010 Foreword The text of document 34A/1027/FDIS, future edition of IEC 61549, prepared by SC 34A, Lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61549 on 2003-06-01 This European Standard supersedes EN 61549:1996 + A1:1997 + A2:2001 The following dates were fixed: – latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2004-03-01 – latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2006-06-01 Endorsement notice The text of the International Standard IEC 61549:2003 was approved by CENELEC as a European Standard without any modification Foreword to amendment A1 The text of document 34A/1124/FDIS, future amendment to IEC 61549:2003, prepared by SC 34A, Lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 61549:2003 on 2005-04-01 The following dates were fixed: – latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2006-01-01 – latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2008-04-01 Endorsement notice The text of amendment 1:2005 to the International Standard IEC 61549:2003 was approved by CENELEC as an amendment to the European Standard without any modification Page BS EN 61549:2003+A3:2012 Page EN 61549:2003+A3:2012 BS EN 61549:2003+A2:2010 EN 61549:2003+A2:2010 Foreword to amendment A2 The text of document 34A/1372/FDIS, future amendment to IEC 61549:2003, prepared by SC 34A, Lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A2 to EN 61549:2003 on 2010-05-01 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CEN and CENELEC shall not be held responsible for identifying any or all such patent rights The following dates were fixed: – latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2011-02-01 – latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2013-05-01 Endorsement notice The text of amendment 2:2010 to the International Standard IEC 61549:2003 was approved by CENELEC as an amendment to the European Standard without any modification EN 61549:2003/A3:2012 -2 ForewordForeword to amendment A3 The text of document 34A/1568/FDIS, future edition of IEC 61549:2003/A3, prepared by SC 34A, "Lamps", of IEC TC 34, "Lamps and related equipment" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61549:2003/A3:2012 The following dates are fixed: • • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement latest date by which the national standards conflicting with the document have to be withdrawn (dop) 2013-05-09 (dow) 2015-08-09 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC) Endorsement notice The text of the International Standard IEC 61549:2003/A3:2012 was approved by CENELEC as a European Standard without any modification Page BSPage EN461549:2003+A3:2012 EN 61549:2003+A3:2012 BS EN 61549:2003+A2:2010 EN 61549:2003+A2:2010 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies Add: Publication Year Title EN/HD Year IEC 60081 + A1 (mod) + A2 + A3 1997 2000 2003 2005 Double-capped fluorescent lamps Performance specifications EN 60081 + A1 + A2 + A3 1998 2002 2003 2005 IEC 60598-1 (mod) - Luminaires Part 1: General requirements and tests EN 60598-1 - IEC 60695-2-10 - Fire hazard testing EN 60695-2-10 Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure - IEC 60921 - Ballasts for tubular fluorescent lamps Performance requirements EN 60921 - IEC 60929 - AC-supplied electronic ballasts for tubular EN 60929 fluorescent lamps - Performance requirements - IEC 61195 - Double-capped fluorescent lamps - Safety specifications EN 61195 - IEC 61347-2-3 - Lamp controlgear Part 2-3: Particular requirements for a.c supplied electronic ballasts for fluorescent lamps EN 61347-2-3 - IEC 61347-2-8 - Lamp controlgear Part 2-8: Particular requirements for ballasts for fluorescent lamps EN 61347-2-8 - ISO 4046-4 2002 Paper, board, pulps and related terms Vocabulary Part 4: Paper and board grades and converted products - - PagePage EN 61549:2003+A3:2012 BS EN BS 61549:2003+A2:2010 EN 61549:2003+A2:2010 EN 61549:2003 +A2:2010 MISCELLANEOUS LAMPS Scope This International Standard specifies lamps, or information relevant to lamps, not given elsewhere in existing IEC lamp standards It covers both safety and performance aspects NOTE For reasons of flexibility, the information in this loose-leaf publication is given in data sheet format General requirement The lamps specified in this standard shall comply with the relevant safety standard, if available 3.1 Data sheets General principle of numbering of data sheets The first number represents the number of this standard: 61549, followed by the letters “IEC” The second number represents the data sheet number The third number represents the edition of the page of the data sheet In cases where a data sheet has more than one page, it is possible for the pages to have different edition numbers with the data sheet number remaining the same 3.2 List of data sheets Sheet number Subject 61549-IEC-110 Double-capped metal halide lamps (Fc2 caps) - Dimensions 61549-IEC-120 Double-capped incandescent lamps (S14s caps) - Dimensions 61549-IEC-130 Double-capped fluorescent lamps (Fa8 caps) - Dimensions 61549-IEC-140 U-shaped double-capped fluorescent lamps (2G13-92 caps) - Dimensions 61549-IEC-150 Double-capped incandescent lamps (S15s) - Dimensions 61549-IEC-310 Germicidal lamps - Symbol 61549-IEC-320 Radiation hazard - Symbol 61549-IEC-330 Lamp operating positions - Symbols 61549-IEC-340 Protect against direct water contact - Symbol 61549-IEC-510 Tungsten filament ELV lamps - Marking 61549-IEC-520 Lamps for lighting chains - Filament position 61549-IEC-710 Xenon flash lamps with ignition transformer 61549-IEC-720 Metal halide lamps for film and television recording 61549-IEC-810 Requirements for double-capped fluorescent fragment retention lamps blank BS EN BS61549:2003+A2:2010 EN 61549:2003+A3:2012 ENEN 61549:2003 61549:2003 DOUBLE-CAPPED METAL HALIDE LAMPS Dimensions Dimensions in millimetres Caps Fc2 (1) This drawing gives information for specifying the mounting distance between the two Fc2 lampholders for those double-capped metal halide lamps that are not standardized in IEC 61167 (2) max ØD A (3) (3) Nominal wattage W A A max D max 400 182 183 32,5 000 233 234 36,0 (1) See cap sheet 7004-114 of IEC 60061-1 and for holder dimensions and calculation of mounting distances, see sheet 7005-114 of IEC 60061-2 (2) The position of the exhaust tip is not specified (3) Reference planes of the caps 61549-IEC-110-1 BS EN 61549:2003+A3:2012 EN 61549:2003/A3:2012 61549 Amend © IEC:2012 METAL HALIDE LAMPS FOR FILM AND TELEVISION RECORDING Page 1/3 Introduction This data sheet specifies dimensions and technical data for metal halide lamps for film and television recording These lamps have a short or medium arc length and a spectral power distribution similar to daylight The list of lamp types and data given in Table and Figure is not exhaustive General lamp requirements Lamps shall comply with the data given in Table Details which are not indicated may be chosen appropriately The correlated colour temperature (T CP ) shall be about 000 K The colour rendering index (R a ) shall be at least 80 For the photobiological safety, the relevant provisions of IEC 62035* apply Information for ballast and ignitor design For the operation of the lamps, proper controlgears and ignitors are needed If indicated by the lamp manufacturer, hot restrike should be possible at any time Information for luminaire design For safety reasons, adequate protection should be ensured against both UV radiation and possible lamp shattering *IEC 62035, Discharge lamps (excluding fluorescent lamps) Safety specifications Texte franỗais au verso French text overleaf 61549-IEC-720-2 blank BS EN 61549:2003+A3:2012 EN 61549:2003/A3:2012 61549 Amend © IEC:2012 METAL HALIDE LAMPS FOR FILM AND TELEVISION RECORDING Page 2/3 Table – Lamp types and data Type B C D D1 E E1 E2 E3 F Nominal wattage Rated voltage (10) Rated current Dimensions mm Lamp cap W V A L1 max L2 (8) L3 (8) D max 575 95 7,0 135 115 23,5 200 100 13,8 135 115 23,5 200 100 13,8 220 180 10 30 500 115 25,6 355 290 17 (9) 35 000 200 24,0 405 340 34 40 000 123 55,0 450 - 22 58 12 000 224 62,0 470 - 34 70 12 000 160 84,0 470 - 28 (9) 70 18 000 225 88,0 500 - 44 75 125 80 1,7 65 27,7 270 50 5,4 84 35 125 80 1,9 75 200 70 3,0 400 70 575 95 Operating position (11) SFc10-4 (1) any SFc15.5-6 (1) SFa21-12 (2) p30 p15 S25.5x60 (3) p15 S30x70 (3) p15 10 GX13-2x0.8 (3) any 12,5 FaX1.5-3x1 (3) p45 39 17 GZX9.5 (4) 80 39 20 GZY9.5 (4) 6,9 110 60 23 GZZ9.5 (4) 7,0 145 70 30 G22 (5) G38 (6) 200 100 13,8 220 107 10 41 500 115 25,6 240 127 14 60 000 200 24,0 255 142 22 (9) 77 000 125 55,0 380 210 24 75 12 000* 160 * 84 * 460 * 255 * 30 * 105 * 200 100 13,8 176 - - 206 (1) See cap sheet 7004-160 of IEC 60061-1 (2) See cap sheet 7004-159 of IEC 60061-1 (3) Cap sheet in preparation (4) See cap sheet 7004-70B of IEC 60061-1 (5) See cap sheet 7004-75 of IEC 60061-1 any G38 (6) any G38 (6) (7) s135 G38 (6) p0 (6) See cap sheet 7004-76 of IEC 60061-1 (7) Version with increased creepage distance The design of the cap shell area may be different depending on the lamp manufacturer For details, particularly for the lamp support, the lamp manufacturer shall be consulted (8) For the tolerance of this parameter, the lamp manufacturer shall be consulted Differences in length exist in hot and cold operating conditions (9) For the same rated voltage, the electrode gap distance may vary dependent on the lamp manufacturer (10) Deviations of ±10 % and more are possible For details, the lamp manufacturer shall be consulted (11) See sheet 61549-IEC-330 of this standard for the use of these codes * Under consideration Texte franỗais au verso French text overleaf 61549-IEC-720-2 blank BS EN 61549:2003+A3:2012 EN 61549:2003/A3:2012 61549 Amend © IEC:2012 METAL HALIDE LAMPS FOR FILM AND TELEVISION RECORDING Page 3/3 Type B ∅D L3 L2 L1 Type C ∅D L3 L2 L1 Type D and D1 ∅D L3 L1 Type E E1 E2 E3 ∅D ∅D ∅D ∅D L3 L1 L2 L3 L1 L2 L3 L1 L2 F L3 ∅D L1 L2 L1 IEC 1204/12 Figure – Lamp types and location of lamp dimensions Texte franỗais au verso French text overleaf 61549-IEC-720-2 blank BS EN 61549:2003+A2:2010 BS EN 61549:2003+A3:2012 EN 61549:2003/A2:2010 EN 61549:2003/A2:2010 REQUIREMENTS FOR DOUBLE-CAPPED FLUORESCENT FRAGMENT RETENTION LAMPS Page of Scope This datasheet specifies requirements for double-capped fluorescent fragment retention lamps for general lighting purposes Normative references IEC 60081:1997, Double-capped fluorescent lamps – Performance specifications Amendment (2000) Amendment (2003) Amendment (2005) IEC 60598-1, Luminaires – Part 1: General requirements and tests IEC 60695-2-10, Fire hazard testing – Part 2-10: Glowing/hot-wire based test methods – Glowwire apparatus and common test procedure IEC 60921, Ballasts for tubular fluorescent lamps – Performance requirements IEC 60929, AC-supplied electronic ballasts for tubular fluorescent lamps – Performance requirements IEC 61195, Double-capped fluorescent lamps – Safety specifications IEC 61347-2-3, Lamp controlgear – Part 2-3: Particular requirements for a.c supplied electronic ballasts for fluorescent lamps IEC 61347-2-8, Lamp controlgear – Part 2-8: Particular requirements for ballasts for fluorescent lamps ISO 4046-4:2002, Paper, board, pulps and related terms – Vocabulary – Part 4: Paper and board grades and converted products Terms and definitions The terms and definitions of IEC 61195 (safety) and IEC 60081 (performance) apply together with the following 3.1 fragment retention lamp lamp having additional integral protection (for example by means of sleeving or coating) to reduce the risk of cap detachment and ejection of glass fragments in the event of lamp breakage 61549-IEC-810-1 This page deliberately set blank BS EN 61549:2003+A2:2010 BS EN 61549:2003+A3:2012 EN EN 61549:2003/A2:2010 61549:2003/A2:2010 REQUIREMENTS FOR DOUBLE-CAPPED FLUORESCENT FRAGMENT RETENTION LAMPS Page of 3.2 open rated life life declared by manufacturer for which the fragment retention lamp shall perform both its illumination and fragment retention functions when used in an open luminaire NOTE The open rated life value relates to the life over which the lamp will perform its intended function and does not relate to a 50 % failure point 3.3 enclosed rated life life declared by manufacturer for which the fragment retention lamp shall perform both its illumination and fragment retention functions when used in an enclosed (IP65 or higher) luminaire NOTE The enclosed rated life value relates to the life over which the lamp will perform its intended function and does not relate to a 50 % failure point Requirements 4.1 General Fragment retention lamps shall comply with all of the requirements of IEC 61195 (safety) and IEC 60081 (performance) in addition to the following additional requirements 4.2 Marking 4.2.1 Lamp marking Marking to identify the lamp as a fragment retention lamp shall be legibly and durably marked: a) lamps suitable for open and enclosed luminaires shall be marked with one visible band/ring mm minimum width applied around the lamp within 150 mm of one lamp cap, or b) lamps ONLY suitable for open luminaires shall be marked with two visible bands/rings mm minimum width and spaced between mm and 10 mm apart applied around the same end of the lamp within 150 mm of one lamp cap Compliance shall be checked by the following: – presence and legibility of the marking by visual inspection; – durability of marking by applying the following test on unused lamps The area of the marking on the lamp shall be rubbed by hand with a smooth cloth dampened with water for a period of 15 s After this test, the marking shall still be legible 61549-IEC-810-1 This page deliberately set blank BS EN 61549:2003+A3:2012 BS EN 61549:2003+A2:2010 61549:2003/A2:2010 EN EN 61549:2003/A2:2010 REQUIREMENTS FOR DOUBLE-CAPPED FLUORESCENT FRAGMENT RETENTION LAMPS 4.2.2 Page of Additional information The following information shall be provided in the fragment lamp manufacturer’s or responsible vendor’s instructions/catalogue: a) open rated life in hours; b) enclosed rated life in hours (if applicable); c) explanation of ring and ring marking Compliance shall be checked by inspection The following information shall be provided on the lamp packaging and in the manufacturer’s instructions/catalogue, if applicable: d) for lamps marked with rings a caution notice stating “This lamp shall not be used in enclosed (IP65 or higher) fittings” or equivalent; e) caution notice stating “This lamp shall be replaced at the end of the rated life” or equivalent; f) other restrictions/requirements NOTE Other restrictions/requirements might be related to foreseeable misuse Compliance shall be checked by inspection 4.3 Resistance to heat and fire The lamp coating/sleeve shall be resistant to heat and fire Compliance is checked by the following test 4.3.1 Glow-wire test The lamp coating/sleeve is subjected to a test using a nickel-chromium glow-wire heated to 650 °C The test apparatus shall be that described in IEC 60695-2-10 The glow-wire temperature and heating current shall be constant for prior to commencing the test Care shall be taken to ensure that heat radiation does not influence the specimen during this period The glow-wire tip temperature is measured by means of a sheathed finewire thermocouple constructed and calibrated as described in IEC 60695-2-10 The lamp coating/sleeve to be tested is removed from the lamp and mounted on the carriage and pressed against the glowwire tip with a force of N, preferably 15 mm or more from the upper edge of the specimen The penetration of the glow-wire into the specimen is mechanically limited to mm After 30 s, the specimen is withdrawn from contact with the glow-wire tip 61549-IEC-810-1 This page deliberately set blank BS EN BS 61549:2003+A2:2010 EN 61549:2003+A3:2012 EN 61549:2003/A2:2010 EN 61549:2003/A2:2010 REQUIREMENTS FOR DOUBLE-CAPPED FLUORESCENT FRAGMENT RETENTION LAMPS Page of Any flame or glowing of the specimen shall extinguish within 30 s of withdrawing the glow-wire and any burning or molten drop shall not ignite a piece of five-layer tissue paper, specified in 4.187 of ISO 4046-4, spread out horizontally 200 mm ± mm below the specimen NOTE Precautions should be taken to safeguard the health of personnel conducting tests against risk of explosion or fire, of inhalation of smoke and/or toxic products, and of toxic residues 4.4 Impact resistance Fragment retention lamps shall have sufficient impact resistance throughout life Compliance shall be checked by means of the drop test specified in Subclause 4.4.1 on new lamps and following ageing to 000 h as specified in Subclauses 4.4.2.1 and/or 4.4.2.2 as applicable 4.4.1 Drop test Lamps shall be dropped horizontally from a height of m onto a flat concrete, or similar surface NOTE The use of a simple mechanical jig to hold the lamp and release it in a controlled manner to ensure that the lamp drops horizontally is recommended It is recognised that lamps may not impact the surface horizontally Lamps are considered to have passed the test if all glass fragments and the lamp caps are retained by the coating/sleeving Glass fragments are allowed to puncture the coating/sleeving but shall be retained by it A sample of N = 60 lamps without any retention failures is required for type test compliance 4.4.2 Ageing 4.4.2.1 Lamps with open rated life Lamps shall be aged in accordance with the life test conditions as specified in Annex C of IEC 60081 NOTE If the open and enclosed rated life claims are identical, this test may be omitted 4.4.2.2 Lamps with enclosed rated life Lamps shall be aged in a twin lamp enclosed IP65 or higher rated luminaire (with both lamps operating) in accordance with IEC 60598-1 operated at rated voltage The luminaire shall use a ballast(s) in accordance with IEC 61347-2-3 and IEC 60921 for lamps suitable for use on magnetic control gear or with IEC 61347-2-8 and IEC 60929 for lamps only suitable for high frequency operation The operating cycle shall be in accordance with Clause C.1 of IEC 60081 61549-IEC-810-1 This page deliberately set blank blank