BS EN 10365:2017 Incorporating corrigendum February 2017 BS EN 10365:2017 BSI Standards Publication Hot rolled steel channels, I and H sections — Dimensions and masses BS EN 10365:2017 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 10365:2017 It supersedes BS 4-1:2005 which is withdrawn The UK participation in its preparation was entrusted to Technical Committee ISE/103, Structural Steels Other Than Reinforcements A list of organizations represented on this committee can be obtained on request to its secretary This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application © The British Standards Institution 2017 Published by BSI Standards Limited 2017 ISBN 978 580 97605 ICS 77.140.70 Compliance with a British Standard cannot confer immunity from legal obligations This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2017 Amendments/corrigenda issued since publication Date Text affected 28 February 2017 Supersession information updated BS EN 10365:2017 EN 10365 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM January 2017 ICS 77.140.70 English Version Hot rolled steel channels, I and H sections - Dimensions and masses Profilés en U en aciers laminés chaud, poutrelles I et H - Dimensions et masses Warmgewalzter U-Profilstahl, I- und H-Träger - Maße und Masse This European Standard was approved by CEN on 14 November 2016 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels © 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref No EN 10365:2017 E BS EN 10365:2017 EN 10365:2017 (E) Contents Page European foreword Scope Normative references Terms and definitions Designation 5 Dimensions and masses Tolerances on dimensions, shape and mass 7 Material Annex A (informative) Comparison of symbols used in this document with those in EN 1993-1-1 32 Bibliography 33 BS EN 10365:2017 EN 10365:2017 (E) European foreword This document (EN 10365:2017) has been prepared by Technical Committee ECISS/TC 103 “Structural steels other than reinforcements”, the secretariat of which is held by DIN This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2017, and conflicting national standards shall be withdrawn at the latest by July 2017 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CEN shall not be held responsible for identifying any or all such patent rights This project was submitted to the Enquiry under reference prEN 16828 According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom BS EN 10365:2017 EN 10365:2017 (E) Scope This European standard specifies the nominal dimensions and masses of the hot rolled steel channels, I and H sections The following shapes are covered by this standard: Sections: — Parallel flange I sections IPE; — Wide flange beams HE; — Extra wide flange beams HL and HLZ; — Wide flange columns HD; — Wide flange bearing piles HP and UBP; — Universal beams UB; — Universal columns UC; — Taper flange I sections IPN and J Channels: — Parallel flange channels UPE and PFC; — Taper flange channels UPN, U and CH These requirements not apply to hot rolled steel channels, I and H sections from stainless steel Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies EN 10024, Hot rolled taper flange I sections - Tolerances on shape and dimensions EN 10025-1, Hot rolled products of structural steels - Part 1: General technical delivery conditions EN 10025-2, Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels EN 10025-3, Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels EN 10025-4, Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels EN 10025-5, Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance EN 10034, Structural steel I and H sections - Tolerances on shape and dimensions BS EN 10365:2017 EN 10365:2017 (E) EN 10079, Definition of steel products EN 10279, Hot rolled steel channels - Tolerances on shape, dimensions and mass Terms and definitions For the purposes of this document, the terms and definitions given in EN 10079 apply Designation A section shall be designated according to Tables to 15 This form of designation shall be used in any enquiry and order Dimensions and masses Hot rolled steel channels, I and H sections complying with this European Standard shall be manufactured with the specified dimensions given in the Table to 15 and according to Figures to below Radii of fillets and toes of shape profiles vary with individual manufacturers and therefore are not specified The masses per unit length specified in Tables to 15 were calculated on the basis of a density of 7850 kg/m3 Figure — IPE, HE, HL, HD, HP, UBP, UB and UC parallel flange sections BS EN 10365:2017 EN 10365:2017 (E) Figure — Taper flange I sections IPN, J and extra wide flange beams HLZ Figure — Parallel flange channels UPE and PFC Figure — Taper flange channels UPN, U and CH BS EN 10365:2017 EN 10365:2017 (E) Tolerances on dimensions, shape and mass Tolerances on dimensions, shape and mass shall be as given in EN 10034 for I (parallel flanges) and H sections Tolerances on dimensions, shape and mass shall be as given in EN 10024 for taper flange I sections Tolerances on dimensions, shape and mass shall be as given in EN 10279 for channels Tolerances for shapes not included in the mentioned standards shall be as agreed upon between the manufacturer and the purchaser Material Sections and channels shall preferably be made from steel of a grade as specified in EN 10025-1, EN 10025-2, EN 10025-3, EN 10025-4 and EN 10025-5 Other steel grades as specified in EN 10225, EN 10028-2 and EN 10273 may also be used for specific applications The desired steel grade shall be specified at the time of ordering BS EN 10365:2017 EN 10365:2017 (E) Table — Parallel flange I sections IPE Designation G h b s t A kg/m mm mm mm mm cm2 IPE AA 80 4,9 78,0 46,0 3,2 4,2 6,3 IPE 80 6,0 80,0 46,0 3,8 5,2 7,6 IPE A 80 IPE AA 100 IPE A 100 IPE 100 IPE AA 120 IPE A 120 5,0 6,7 6,9 117,6 10,5 IPE A 160 IPE 160 IPE AA 180 IPE A 180 IPE 180 IPE O 180 IPE AA 200 IPE A 200 IPE 200 IPE O 200 IPE AA 220 IPE A 220 IPE 220 IPE O 220 IPE AA 240 IPE A 240 IPE 240 IPE O 240 98,0 8,7 8,4 IPE A 140 IPE AA 160 97,6 100,0 10,4 IPE 140 78,0 8,1 IPE 120 IPE AA 140 Dimensions 10,1 12,9 12,3 12,7 15,8 14,9 15,4 18,8 21,3 18,0 18,4 22,4 25,1 21,2 22,2 26,2 29,4 24,9 26,2 30,7 34,3 117,0 120,0 136,6 137,4 140,0 156,4 157,0 160,0 176,4 177,0 180,0 182,0 46,0 55,0 55,0 55,0 64,0 64,0 64,0 73,0 73,0 73,0 82,0 82,0 82,0 91,0 91,0 91,0 92,0 196,4 100,0 200,0 100,0 197,0 202,0 216,4 217,0 220,0 222,0 236,4 237,0 240,0 242,0 100,0 102,0 110,0 110,0 110,0 112,0 120,0 120,0 120,0 122,0 3,3 3,6 3,6 4,1 3,8 3,8 4,4 3,8 3,8 4,7 4,0 4,0 5,0 4,3 4,3 5,3 6,0 4,5 4,5 5,6 6,2 4,7 5,0 5,9 4,2 4,5 4,7 5,1 11,0 4,8 6,3 5,2 5,6 6,9 5,6 5,9 7,4 6,2 6,5 8,0 9,0 6,7 7,0 8,5 9,5 7,4 7,7 9,2 5,2 8,3 7,0 8,8 10,3 10,2 6,2 8,6 5,7 6,6 4,8 6,4 8,0 9,8 10,8 10,7 13,2 12,8 13,4 16,4 15,7 16,2 20,1 19,0 19,6 23,9 27,1 22,9 23,5 28,5 32,0 27,0 28,3 33,4 37,4 31,7 33,3 39,1 43,7 BS EN 10365:2017 EN 10365:2017 (E) Table — Universal beams UB Designation G h b s t A kg/m mm mm mm mm cm2 UB 127 × 76 × 13 13,0 127,0 76,0 4,0 7,6 16,5 UB 178 × 102 × 19 19,0 177,8 101,2 4,8 7,9 24,3 203,2 133,2 UB 152 × 89 × 16 UB 203 × 102 × 23 UB 203 × 133 × 25 UB 203 × 133 × 30 UB 254 × 102 × 22 UB 254 × 102 × 25 UB 254 × 102 × 28 UB 254 × 146 × 31 UB 254 × 146 × 37 UB 254 × 146 × 43 UB 305 × 102 × 25 UB 305 × 102 × 28 UB 305 × 102 × 33 UB 305 × 127 × 37 UB 305 × 127 × 42 UB 305 × 127 × 48 UB 305 × 165 × 40 UB 305 × 165 × 46 UB 305 × 165 × 54 UB 356 × 127 × 33 UB 356 × 127 × 39 UB 356 × 171 × 45 UB 356 × 171 × 51 UB 356 × 171 × 57 UB 356 × 171 × 67 UB 406 × 140 × 39 UB 406 × 140 × 46 UB 406 × 178 × 54 UB 406 × 178 × 60 22 Dimensions 16,0 23,1 25,1 30,0 22,0 25,2 28,3 31,1 37,0 43,0 24,8 28,2 32,8 37,0 41,9 48,1 40,3 46,1 54,0 33,1 39,1 45,0 51,0 57,0 67,1 39,0 46,0 54,1 60,1 152,4 203,2 206,8 254,0 257,2 260,4 251,4 256,0 259,6 305,1 308,7 312,7 304,4 307,2 311,0 303,4 306,6 310,4 349,0 353,4 351,4 355,0 358,0 363,4 398,0 403,2 402,6 406,4 88,7 101,8 133,9 101,6 101,9 102,2 146,1 146,4 147,3 101,6 101,8 102,4 123,4 124,3 125,3 165,0 165,7 166,9 125,4 126,0 171,1 171,5 172,2 173,2 141,8 142,2 177,7 177,9 4,5 5,4 5,7 6,4 5,7 6,0 7,7 9,3 7,8 9,6 6,8 8,4 6,3 10,0 6,3 10,9 5,8 7,0 6,0 7,2 6,0 8,6 12,7 8,8 6,6 10,8 8,0 12,1 7,1 9,0 6,0 6,7 7,9 6,0 10,7 14,0 10,2 11,8 13,7 8,5 6,6 10,7 7,4 11,5 9,1 15,7 7,0 8,1 6,4 9,7 13,0 8,6 6,8 11,2 7,9 12,8 7,7 10,9 20,3 29,4 32,0 38,2 28,0 32,0 36,1 39,7 47,2 54,8 31,6 35,9 41,8 47,2 53,4 61,2 51,3 58,7 68,8 42,1 49,8 57,3 64,9 72,6 85,5 49,7 58,6 69,0 76,5 BS EN 10365:2017 EN 10365:2017 (E) Designation Dimensions G h b s t A kg/m mm mm mm mm cm2 UB 406 × 178 × 67 67,1 409,4 178,8 8,8 14,3 85,5 UB 457 × 152 × 52 52,3 449,8 152,4 7,6 10,9 66,6 UB 406 × 178 × 74 UB 457 × 152 × 60 UB 457 × 152 × 67 UB 457 × 152 × 74 UB 457 × 152 × 82 UB 457 × 191 × 67 UB 457 × 191 × 74 UB 457 × 191 × 82 UB 457 × 191 × 89 UB 457 × 191 × 98 UB 533 × 210 × 82 UB 533 × 210 × 92 UB 533 × 210 × 101 UB 533 × 210 × 109 UB 533 × 210 × 122 UB 610 × 229 × 101 UB 610 × 229 × 113 UB 610 × 229 × 125 UB 610 × 229 × 140 UB 610 × 305 × 149 UB 610 × 305 × 179 UB 610 × 305 × 238 UB 686 × 254 × 125 UB 686 × 254 × 140 UB 686 × 254 × 152 UB 686 × 254 × 170 UB 762 × 267 × 134 UB 762 × 267 × 147 UB 762 × 267 × 173 UB 762 × 267 × 197 UB 838 × 292 × 176 74,2 59,8 67,2 74,2 82,1 67,1 74,3 82,0 89,3 98,3 82,2 92,1 101 109 122 101 113 125 140 149 179 238 125 140 152 170 134 147 173 197 176 412,8 454,6 458,0 462,0 465,8 453,4 457,0 460,0 463,4 467,2 528,3 533,1 536,7 539,5 544,5 602,6 607,6 612,2 617,2 612,4 620,2 635,8 677,9 683,5 687,5 692,9 750,0 754,0 762,2 769,8 834,9 179,5 152,9 153,8 154,4 9,5 8,1 9,0 9,6 155,3 10,5 190,4 9,0 189,9 191,3 8,5 9,9 191,9 10,5 208,8 9,6 192,8 11,4 209,3 10,1 210,8 11,6 210,0 211,9 227,6 228,2 229,0 230,2 304,8 307,1 311,4 253,0 253,7 254,5 255,8 264,4 265,2 266,7 268,0 291,7 10,8 12,7 10,5 11,1 11,9 13,1 11,8 14,1 18,4 11,7 12,4 13,2 14,5 12,0 12,8 14,3 15,6 14,0 16,0 13,3 15,0 17,0 94,5 76,2 85,6 94,5 18,9 104,5 14,5 94,6 12,7 85,5 16,0 104,5 19,6 125,3 17,7 13,2 15,6 17,4 18,8 21,3 14,8 17,3 19,6 22,1 19,7 23,6 31,4 16,2 19,0 21,0 23,7 15,5 17,5 21,6 25,4 18,8 113,8 104,7 117,4 128,7 138,9 155,4 128,9 143,9 159,3 178,2 190,0 228,1 303,3 159,5 178,4 194,1 216,8 170,6 187,2 220,4 250,6 224,0 23 BS EN 10365:2017 EN 10365:2017 (E) Designation G h b s t A kg/m mm mm mm mm cm2 UB 838 × 292 × 194 194 840,7 292,4 14,7 21,7 246,8 UB 914 × 305 × 201 201 903,0 303,3 15,1 20,2 255,9 UB 838 × 292 × 226 UB 914 × 305 × 224 UB 914 × 305 × 238 UB 914 × 305 × 253 UB 914 × 305 × 271 UB 914 × 305 × 289 UB 914 × 305 × 313 UB 914 × 305 × 345 UB 914 × 305 × 381 UB 914 × 305 × 425 UB 914 × 305 × 474 UB 914 × 305 × 521 UB 914 × 305 × 576 UB 914 × 419 × 343 UB 914 × 419 × 388 UB 1016 × 305 × 222 UB 1016 × 305 × 249 UB 1016 × 305 × 272 UB 1016 × 305 × 314 UB 1016 × 305 × 350 UB 1016 × 305 × 393 UB 1016 × 305 × 415 UB 1016 × 305 × 438 UB 1016 × 305 × 494 UB 1016 × 305 × 584 24 Dimensions 226 224 238 253 271 289 313 345 381 425 474 521 576 343 388 222 249 272 850,9 910,4 915,0 918,4 923,0 926,6 932,0 943,0 951,0 961,0 971,0 981,0 993,0 911,8 921,0 970,0 980,0 990,0 314 1000,0 393 1016,0 350 415 438 494 584 1008,0 1020,0 1026,0 1036,0 1056,0 293,8 304,1 305,0 305,5 307,0 307,7 309,0 308,0 310,0 313,0 316,0 319,0 322,0 418,5 420,5 300,0 300,0 300,0 300,0 302,0 303,0 304,0 305,0 309,0 314,0 16,1 15,9 16,5 17,3 18,4 19,5 21,1 22,1 24,4 26,9 30,0 33,0 36,1 19,4 21,4 16,0 16,5 16,5 19,1 21,1 24,4 26,0 26,9 31,0 36,0 26,8 23,9 25,9 27,9 30,0 32,0 34,5 39,9 43,9 49,0 54,1 58,9 65,0 32,0 36,6 21,1 26,0 31,0 35,9 40,0 43,9 46,0 49,0 54,0 64,0 288,6 285,6 303,5 322,8 346,1 368,3 398,4 439,7 485,9 542,0 603,9 663,7 733,2 437,3 494,2 282,8 316,8 346,8 400,4 445,1 500,2 528,7 556,3 629,1 743,7 BS EN 10365:2017 EN 10365:2017 (E) Table — Universal columns UC Designation Dimensions G h b s t A kg/m mm mm mm mm cm2 UC 152 × 152 × 23 23,0 152,4 152,2 5,8 6,8 29,2 UC 203 × 203 × 46 46,1 203,2 203,6 7,2 11,0 58,7 UC 152 × 152 × 30 UC 152 × 152 × 37 UC 203 × 203 × 52 UC 203 × 203 × 60 UC 203 × 203 × 71 UC 203 × 203 × 86 UC 254 × 254 × 73 UC 254 × 254 × 89 UC 254 × 254 × 107 UC 254 × 254 × 132 UC 254 × 254 × 167 30,0 37,0 52,0 60,0 71,0 86,1 73,1 88,9 107 132 167 UC 305 × 305 × 97 96,9 UC 305 × 305 × 158 158 UC 305 × 305 × 118 UC 305 × 305 × 137 UC 305 × 305 × 198 UC 305 × 305 × 240 UC 305 × 305 × 283 UC 356 × 368 × 129 UC 356 × 368 × 153 UC 356 × 368 × 177 UC 356 × 368 × 202 UC 356 × 406 × 235 UC 356 × 406 × 287 UC 356 × 406 × 340 UC 356 × 406 × 393 UC 356 × 406 × 467 UC 356 × 406 × 509 UC 356 × 406 × 551 UC 356 × 406 × 592 UC 356 × 406 × 634 UC 356 × 406 × 677 UC 356 × 406 × 744 UC 356 × 406 × 818 118 137 198 240 283 129 153 177 202 235 287 340 393 467 509 551 592 634 677 744 818 157,6 161,8 206,2 209,6 215,8 222,2 254,1 260,3 266,7 276,3 289,1 307,9 314,5 320,5 327,1 339,9 352,5 365,3 355,6 362,0 368,2 374,6 381,0 393,6 406,4 419,0 436,6 446,0 455,6 465,0 474,6 483,0 498,0 514,0 152,9 154,4 204,3 205,8 6,5 8,0 11,5 9,4 14,2 7,9 206,4 10,0 256,3 10,3 209,1 254,6 258,8 261,3 265,2 305,3 307,4 309,2 311,2 314,5 318,4 322,2 368,6 370,5 372,6 374,7 394,8 399,0 403,0 407,0 412,2 416,0 418,5 421,0 424,0 428,0 432,0 437,0 9,4 12,7 8,6 12,8 15,3 19,2 9,9 12,0 13,8 15,8 19,1 23,0 26,8 10,4 12,3 14,4 16,5 18,4 22,6 26,6 30,6 35,8 39,1 42,1 45,0 47,6 51,2 55,6 60,5 12,5 17,3 38,3 47,1 66,3 76,4 90,4 20,5 109,6 20,5 136,4 14,2 17,3 25,3 31,7 15,4 18,7 21,7 25,0 31,4 37,7 44,1 17,5 20,7 23,8 27,0 30,2 36,5 42,9 49,2 58,0 62,7 67,5 72,3 77,0 81,5 88,9 97,0 93,1 113,3 168,1 212,9 123,4 150,2 174,4 201,4 252,4 305,8 360,4 164,3 194,8 225,5 257,2 299,0 365,7 433,0 500,6 594,9 649,0 701,9 754,9 807,5 863,4 948,1 1043,3 25 BS EN 10365:2017 EN 10365:2017 (E) UC 356 × 406 × 900 UC 356 × 406 × 990 UC 356 × 406 × 1086 UC 356 × 406 × 1202 UC 356 × 406 × 1299 26 900 531,0 442,0 65,9 106,0 1149,2 1202 580,0 471,0 95,0 130,0 1530,6 990 1086 1299 550,0 569,0 600,0 448,0 454,0 476,0 71,9 78,0 100,0 115,0 125,0 140,0 1262,4 1385,8 1654,8 BS EN 10365:2017 EN 10365:2017 (E) Table — Taper flange I sections IPN Designation IPN 80 IPN 100 Dimensions G h b s t A kg/m mm mm mm mm cm2 5,9 80,0 42,0 3,9 5,9 7,6 140,0 66,0 5,7 8,6 8,3 100,0 17,9 160,0 IPN 120 11,1 IPN 180 21,9 IPN 140 IPN 160 IPN 200 IPN 220 IPN 240 IPN 260 IPN 280 IPN 300 IPN 320 IPN 340 IPN 360 IPN 380 IPN 400 IPN 450 IPN 500 IPN 550 IPN 600 14,3 26,2 31,1 36,2 41,9 47,9 54,2 61,0 68,0 76,1 84,0 92,4 115 141 166 199 120,0 180,0 200,0 220,0 50,0 58,0 74,0 82,0 90,0 98,0 240,0 106,0 300,0 125,0 260,0 280,0 320,0 340,0 360,0 380,0 400,0 450,0 500,0 550,0 600,0 113,0 4,5 5,1 6,3 13,1 8,1 9,4 12,2 155,0 170,0 185,0 200,0 215,0 22,8 8,7 7,5 137,0 149,0 9,5 7,7 10,4 10,1 143,0 10,6 6,9 119,0 131,0 6,8 10,8 11,5 13,0 13,7 14,4 16,2 18,0 19,0 21,6 11,3 12,2 14,1 15,2 16,2 17,3 18,3 19,5 14,2 18,2 27,9 33,4 39,5 46,1 53,3 61,0 69,0 77,7 86,7 97,0 20,5 107,0 27,0 179,4 21,6 24,3 30,0 32,4 117,7 146,9 212,0 253,7 27 BS EN 10365:2017 EN 10365:2017 (E) Table 10 — Taper flange I sections J Designation Dimensions G h b s t A kg/m mm mm mm mm cm2 J 76 × 76 × 13 12,8 76,2 76,2 5,1 8,4 16,1 J 102 × 44 × 7,5 101,6 44,5 4,3 6,1 9,4 16,5 127,0 J 76 × 76 × 15 J 89 × 89 × 19 J 102 × 102 × 23 J 114 × 114 × 27 J 127 × 76 × 16 J 127 × 114 × 27 J 127 × 114 × 29 J 152 × 127 × 37 J 203 × 152 × 52 J 254 × 114 × 37 J 254 × 203 × 82 15,0 19,5 23,0 26,9 26,9 29,3 37,3 52,3 37,2 82,0 76,2 88,9 101,6 127,0 114,3 114,3 127,0 152,4 203,2 254,0 254,0 8,9 88,9 101,6 9,5 114,3 76,2 7,4 11,4 9,5 5,6 10,2 114,3 7,6 152,4 203,2 9,9 10,3 114,3 127,0 8,4 9,5 10,4 8,9 10,2 Table 11 — Parallel flange channels UPE Designation 10,7 9,6 11,5 13,2 16,5 12,8 19,9 18,8 24,4 28,8 33,9 20,9 33,8 36,8 46,9 65,9 46,9 103,9 Dimensions G h b s t A kg/m mm mm mm mm cm2 UPE 80 7,9 80,0 50,0 4,0 7,0 10,1 UPE 120 12,1 120,0 60,0 5,0 8,0 15,4 UPE 160 17,0 UPE 100 UPE 140 UPE 180 UPE 200 UPE 220 UPE 240 UPE 270 UPE 300 UPE 330 UPE 360 UPE 400 28 80,0 9,8 100,0 14,5 140,0 19,7 22,8 26,6 30,2 35,2 44,4 53,2 61,2 72,2 160,0 180,0 200,0 220,0 240,0 270,0 55,0 65,0 70,0 75,0 80,0 85,0 90,0 95,0 300,0 100,0 360,0 110,0 330,0 400,0 4,5 5,0 5,5 7,5 9,0 9,5 5,5 10,5 6,5 12,0 6,0 7,0 7,5 9,5 105,0 11,0 115,0 13,5 12,0 11,0 12,5 13,5 15,0 16,0 17,0 18,0 12,5 18,4 21,7 25,1 29,0 33,9 38,5 44,8 56,6 67,8 77,9 91,9 BS EN 10365:2017 EN 10365:2017 (E) Table 12 — Parallel flange channels PFC Designation Dimensions G h b s t A kg/m mm mm mm mm cm2 PFC 100 × 50 × 10 10,2 100,0 50,0 5,0 8,5 13,0 PFC 150 × 75 × 18 17,9 150,0 75,0 5,5 10,0 22,8 6,0 10,5 PFC 125 × 65 × 15 PFC 150 × 90 × 24 PFC 180 × 75 × 20 PFC 180 × 90 × 26 PFC 200 × 75 × 23 PFC 200 × 90 × 30 PFC 230 × 75 × 26 PFC 230 × 90 × 32 PFC 260 × 75 × 28 PFC 260 × 90 × 35 PFC 300 × 90 × 41 PFC 300 × 100 × 46 PFC 380 × 100 × 54 PFC 430 × 100 × 64 14,8 23,9 20,3 26,1 23,4 29,7 25,7 32,2 27,6 34,8 41,4 45,5 54,0 64,4 125,0 150,0 180,0 180,0 200,0 200,0 230,0 230,0 260,0 260,0 300,0 65,0 90,0 75,0 90,0 75,0 90,0 75,0 90,0 75,0 90,0 90,0 300,0 100,0 430,0 100,0 380,0 100,0 5,5 6,5 6,5 6,0 7,0 6,5 7,5 7,0 8,0 9,0 9,0 9,5 11,0 9,5 12,0 12,5 12,5 14,0 12,5 14,0 12,0 14,0 15,5 16,5 17,5 19,0 18,8 30,4 25,9 33,2 29,9 37,9 32,7 41,0 35,1 44,4 52,7 58,0 68,7 82,1 29 BS EN 10365:2017 EN 10365:2017 (E) Table 13 — Taper flange channels UPN Dimensions Designation G h b s t A kg/m mm mm mm mm cm2 UPN 50 5,6 50,0 38,0 5,0 7,0 7,1 UPN 80 8,6 80,0 45,0 6,0 8,0 11,0 9,0 17,0 UPN 65 65,0 UPN 100 10,6 100,0 UPN 140 16,0 140,0 UPN 120 UPN 160 UPN 180 UPN 200 UPN 220 UPN 240 UPN 260 UPN 280 UPN 300 UPN 320 UPN 350 UPN 380 UPN 400 30 7,1 13,4 18,8 22,0 25,3 29,4 33,2 37,9 41,8 46,2 59,5 60,6 63,1 71,8 120,0 160,0 180,0 200,0 220,0 240,0 260,0 42,0 50,0 55,0 60,0 65,0 70,0 75,0 80,0 85,0 5,5 6,0 7,0 10,0 8,0 11,0 7,5 8,5 9,0 9,5 10,0 300,0 100,0 10,0 350,0 100,0 320,0 380,0 400,0 95,0 100,0 102,0 110,0 8,5 7,0 90,0 280,0 7,5 10,0 14,0 14,0 13,5 14,0 10,5 11,5 12,5 13,0 14,0 15,0 16,0 17,5 16,0 16,0 18,0 9,0 13,5 20,4 24,0 28,0 32,2 37,4 42,3 48,3 53,3 58,8 75,8 77,3 80,4 91,5 BS EN 10365:2017 EN 10365:2017 (E) Table 14 — Taper flange channels U Designation Dimensions G h b s t A kg/m mm mm mm mm cm2 U 40 × 20 × 2,6 40,0 20,0 4,0 5,5 3,4 U 50 × 25 × 3,9 50,0 25,0 5,0 6,0 4,9 U 40 × 20 × U 60 × 30 × U 65 × 42 × 5,5 2,9 40,0 5,1 60,0 7,1 65,0 CH 229 × 76 × 26 CH 229 × 89 × 33 CH 254 × 76 × 28 CH 254 × 89 × 36 CH 305 × 89 × 42 CH 305 × 102 × 46 CH 381 × 102 × 55 CH 432 × 102 × 65 9,0 t A kg/m mm mm mm mm cm2 6,7 76,2 38,1 5,1 6,8 8,6 127,0 63,5 6,4 9,2 152,4 CH 203 × 89 × 30 7,5 s 17,9 CH 203 × 76 × 24 5,5 6,5 b CH 152 × 76 × 18 CH 178 × 89 × 27 42,0 6,0 h 101,6 CH 178 × 76 × 21 6,0 3,7 G 10,4 CH 152 × 89 × 24 30,0 5,5 Dimensions CH 102 × 51 × 10 CH 127 × 64 × 15 5,0 Table 15 — Taper flange channels CH Designation CH 76 × 38 × 20,0 14,9 23,9 20,8 26,8 23,9 29,8 26,1 32,7 28,2 35,7 41,8 46,2 55,0 65,5 152,4 177,8 177,8 203,2 203,2 228,6 228,6 254,0 254,0 304,8 50,8 76,2 88,9 76,2 88,9 76,2 88,9 76,2 88,9 76,2 88,9 6,4 22,5 12,3 7,1 8,1 7,6 8,6 8,1 9,1 10,4 101,6 9,0 7,6 6,6 101,6 431,8 13,1 11,6 10,2 101,6 7,6 7,1 88,9 304,8 381,0 6,1 10,2 12,2 10,3 11,2 12,9 11,2 13,3 10,9 13,6 13,7 14,8 16,3 16,8 18,8 30,0 26,4 33,8 30,3 37,6 33,1 41,4 35,9 45,3 53,0 58,1 69,6 82,4 31 BS EN 10365:2017 EN 10365:2017 (E) Annex A (informative) Comparison of symbols used in this document with those in EN 1993-1-1 The symbols used in this standard are in accordance with the tolerance standards EN 10024, EN 10034 and EN 10279 The comparison with the relevant symbols used in the Eurocode standard EN 1993-1-1 are indicated in Table A.1 Table A.1 — Comparison with the symbols used in EN 1993–1–1 EN 10365 EN 10024 EN 10034 EN 10279 EN 1993–1–1 h h Flange width b b s tw Flange thickness t tf Depth Web thickness 32 BS EN 10365:2017 EN 10365:2017 (E) Bibliography EN 1993-1-1, Eurocode 3: Design of steel structures - Part 1-1: General rules and rules for buildings EN 10225, Weldable structural steels for fixed offshore structures - Technical delivery conditions EN 10028-2, Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties EN 10273, Hot rolled weldable steel bars for pressure purposes with specified elevated temperature properties 33 This page deliberately left blank This page deliberately left blank NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards Institution (BSI) BSI is the national body responsible for preparing British Standards and other standards-related publications, information and services BSI is incorporated by Royal Charter British Standards and other standardization products are published by BSI Standards Limited About us Reproducing extracts We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions For permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process Organizations of all sizes and across all sectors choose standards to help them achieve their goals Information on standards We can provide you with the knowledge that your organization needs to succeed Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop, where hard copies can also be purchased If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team Copyright in BSI publications All the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSI’s prior written consent Storing and using standards Standards purchased in soft copy format: • A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only • The standard may be stored on more than device provided that it is accessible by the sole named user only and that only copy is accessed at any one time • A single paper copy may be printed for personal or internal company use only Standards purchased in hard copy format: • A British Standard purchased in hard copy format is for personal or internal company use only • It may not be further reproduced – in any format – to create an additional copy This includes scanning of the document If you need more than copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see ‘Subscriptions’) Subscriptions Our range of subscription services are designed to make using standards easier for you For further information on our subscription products go to bsigroup.com/subscriptions With British Standards Online (BSOL) you’ll have instant access to over 55,000 British and adopted European and international standards from your desktop It’s available 24/7 and is refreshed daily so you’ll always be up to date You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member PLUS is an updating service exclusive to BSI Subscribing Members You will automatically receive the latest hard copy of your standards when they’re revised or replaced To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit bsigroup.com/shop With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet Licences can cover as few or as many users as you wish With updates supplied as soon as they’re available, you can be sure your documentation is current For further information, email subscriptions@bsigroup.com Revisions Our British Standards and other publications are updated by amendment or revision We continually improve the quality of our products and services to benefit your business If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre Useful Contacts Customer Services Tel: +44 345 086 9001 Email (orders): orders@bsigroup.com Email (enquiries): cservices@bsigroup.com Subscriptions Tel: +44 345 086 9001 Email: subscriptions@bsigroup.com Knowledge Centre Tel: +44 20 8996 7004 Email: knowledgecentre@bsigroup.com Copyright & Licensing Tel: +44 20 8996 7070 Email: copyright@bsigroup.com BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK