www bzfxw com BRITISH STANDARD AEROSPACE SERIES BS EN 2933 1996 Bolts, T head, relieved shank, long thread, in heat resisting nickel base alloy NI P100HT (Inconel 718) — Classification 1275 MPa (at am[.]
Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 01:09, Uncontrolled Copy, (c) BSI BRITISH STANDARD AEROSPACE SERIES Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718) — Classification: 1275 MPa (at ambient temperature)/650 °C The European Standard EN 2933:1996 has the status of a British Standard ICS 49.040.20 BS EN 2933:1996 Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 01:09, Uncontrolled Copy, (c) BSI BS EN 2933:1996 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems, upon which the following bodies were represented: Association of Electronic, Telecommunications and Business Equipment Industries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companies This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 June 1996 © BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference ACE/12 Draft for comment 88/76308 DC ISBN 580 25929 Amendments issued since publication Amd No Date Comments Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 01:09, Uncontrolled Copy, (c) BSI BS EN 2933:1996 Contents Committees responsible National foreword Foreword Scope Normative references Required characteristics Designation Marking Technical specification Figure Table Table List of references © BSI 12-1999 Page Inside front cover ii 3 7 Inside back cover i Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 01:09, Uncontrolled Copy, (c) BSI BS EN 2933:1996 National foreword This British Standard has been prepared by Technical Committee ACE/12 and is the English language version of EN 2933:1996 Aerospace series — Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718) — Classification: 275 MPa (at ambient temperature)/650 °C, published by the European Committee for Standardization (CEN) EN 2933:1996 was produced as a result of international discussions in which the United Kingdom took an active part Cross-references Publication referred to Corresponding British Standard EN 2424:1995 ISO 3353:1992 BS EN 2424:1995 Marking of aerospace products BS 2A 231:1993 Rolled threads and bolts Lead and runout requirements BS 6293 Aerospace MJ threads Part 2:1994 Limit dimensions for bolts and nuts ISO 5855-2:1988 A British Standard does not purport to include all the necessary provisions of a contract Users of British Standards are responsible for their correct application Compliance with a British Standard does not of itself confer immunity from legal obligations Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages to 8, an inside back cover and a back cover This standard has been updated (see copyright date) and may have had amendments incorporated This will be indicated in the amendment table on the inside front cover ii © BSI 12-1999 Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 01:09, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD EN 2933 NORME EUROPÉENNE March 1996 EUROPÄISCHE NORM ICS 49.040.20 Descriptors: Aircraft industry, screw, nickel alloy, heat resistant material, classification, dimension, designation English version Aerospace series — Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718) — Classification: 275 MPa (at ambient temperature)/650 °C (ISO 2861:1988) Série aérospatiale- Vis tête en T, fût dégagé filetage long, en alliage résitant chaud base e nickel NI-P100HT (Inconel 718) — Classification: 275 MPa (à temperature ambiante)/650 °C Luft-und Raumfahrt — T-Kopfschrauben, Dünnschaft, langes Gewinde, aus hochwarmfester Nickelbasislegierung NI-P100HT (Inconel 718) — Klasse: 275 MPa (bei Raumtemperatur)/650 °C ｗｗｗ．ｂｚｆｘｗ．ｃｏｍ This European Standard was approved by CEN on 1995-08-31 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels © 1996 Copyright reserved to CEN members Ref No EN 2933:1996 E Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 01:09, Uncontrolled Copy, (c) BSI EN 2933:1996 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA) After inquiries and votes carried out in accordance with the rules of this Association, this Standard has successively received the approval of the National Associations and the Official Services of the members countries of AECMA, prior to its presentation to CEN This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 1996, and conflicting national standards shall be withdrawn at the latest by September 1996 According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom ｗｗｗ．ｂｚｆｘｗ．ｃｏｍ © BSI 12-1999 Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 01:09, Uncontrolled Copy, (c) BSI EN 2933:1996 Scope This standard specifies the characteristics of T-headed bolts with relieved shank, long thread, in NI-P100HT, for aerospace applications Classification: 275 MPa1)/650 °C2) Normative references This European Standard incorporates by dated or undated reference provisions from other publications These normative references are cited at the appropriate places in the text and the publications are listed hereafter For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision For undated references the latest edition of the publication referred to applies ISO 3353, Aerospace — Rolled threads for bolts — Lead and runout requirements ISO 5855-2, Aerospace — MJ threads — Part 2: Limit dimensions for bolts and nuts EN 2424, Aerospace series — Marking of aerospace products EN 2583, Aerospace series — Bolts in heat resisting nickel base alloy NI-P100HT (Inco 718) — Classification: 275 MPa/650 °C — Technical specification3) EN 2952, Aerospace series — Heat resisting alloy NI-PH2601 — Solution treated and cold worked — Bar for forged fasteners — Dk 50 mm — 270 MPa k Rm k 550 MPa3) EN 3219, Aerospace series — Heat resisting nickel base alloy (NI-P100HT) — Cold worked and softened — Bar and wire for continuous forging or extrusion for fasteners – k D k 30 mm3) Required characteristics ｗｗｗ．ｂｚｆｘｗ．ｃｏｍ 3.1 Configuration — Dimensions — Tolerances — Masses See Figure and Table and Table Dimensions and tolerances are in millimetres 3.2 Materials EN 2952 or EN 3219 Table Threada C D E K Q S ± 0,1 ± 0,13 +0,5 +0,5 ± 0,5 +0,3 MJ5×0,8-4h6h 6,2 4,48 11,1 2,9 3,4 8,1 060 MJ6×1-4h6h 7,2 5,35 12 3,4 4,2 9,2 070 MJ7×1-4h6h 8,3 6,35 13,4 5,2 10,2 080 MJ8×1 - h h 9,3 7,35 14 4,5 6,2 11,2 11,1 9,19 16,5 5,3 7,9 13 Code a In Designation MJ10×1,25-4h6h V Y 0,12 0,003 0,15 0,0025 accordance with ISO 5855-2 1) Minimum tensile strength of the material at ambient temperature 2) Maximum test temperature of the parts 3) Published as AECMA Prestandard at the date of publication of this © BSI 12-1999 standard Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 01:09, Uncontrolled Copy, (c) BSI EN 2933:1996 ｗｗｗ．ｂｚｆｘｗ．ｃｏｍ Figure © BSI 12-1999 Length code N ± 0,3 Thread code 050 W max 060 Mass a W max 070 Mass a W max 014 14 016 16 018 18 020 20 022 22 4,5 5,46 024 24 6,5 5,72 4,5 8,09 026 26 10 8,5 5,98 6,5 8,46 028 28 12 10,5 6,23 10 8,5 030 30 14 12,5 6,49 12 10,5 032 32 16 14,5 6,75 14 034 34 18 16,5 7,01 16 036 36 20 18,5 7,27 038 38 22 20,5 7,53 040 40 24 22,5 042 42 26 24,5 044 44 28 046 46 30 048 48 050 50 052 054 080 a W Mass max 100 Mass a Massa W max 4,42 2,5 4,68 4,94 5,20 6,61 2,5 6,98 9,55 7,35 10,07 7,72 2,5 10,59 11,11 13,59 2,5 14,29 14,99 4,5 11,63 15,69 8,83 6,5 12,15 4,5 16,38 9,20 10 8,5 12,67 6,5 17,08 12,5 9,57 12 10,5 13,19 10 14,5 9,94 14 12,5 13,71 12 18 16,5 10,31 16 14,5 14,23 14 20 18,5 10,68 18 16,5 14,75 16 7,79 22 20,5 11,05 20 18,5 15,27 8,05 24 22,5 11,42 22 20,5 15,79 26,5 8,31 26 24,5 11,79 24 22,5 28,5 8,57 28 26,5 12,16 26 24,5 32 30,5 8,83 30 28,5 12,53 28 34 32,5 9,09 32 30,5 12,90 30 52 36 34,5 9,34 34 32,5 13,26 54 38 36,5 9,60 36 34,5 13,63 056 56 40 38,5 9,86 38 36,5 058 58 42 40,5 10,12 40 38,5 060 60 44 42,5 10,38 42 062 62 46 44,5 10,64 44 064 64 48 46,5 10,90 066 66 50 48,5 068 68 52 50,5 24,55 2,7 25,66 26,78 ｗｗｗ．ｂｚｆｘｗ．ｃｏｍ 8,5 17,78 4,5 27,87 10,5 18,48 6,5 28,96 12,5 19,17 10 8,5 30,05 14,5 19,87 12 10,5 31,14 18 16,5 20,57 14 12,5 32,23 20 18,5 21,27 16 14,5 33,32 16,31 22 20,5 21,96 18 16,5 34,40 16,83 24 22,5 22,66 20 18,5 35,49 26,5 17,35 26 24,5 23,36 22 20,5 36,58 28,5 17,88 28 26,5 24,06 24 22,5 37,67 32 30,5 18,40 30 28,5 24,76 26 24,5 38,76 34 32,5 18,92 32 30,5 25,45 28 26,5 39,85 14,00 36 34,5 19,44 34 32,5 26,15 30 28,5 40,93 14,37 38 36,5 19,96 36 34,5 26,85 32 30,5 42,02 40,5 14,74 40 38,5 20,48 38 36,5 27,55 34 32,5 43,11 42,5 15,11 42 40,5 21,00 40 38,5 28,24 36 34,5 44,20 46 44,5 15,48 44 42,5 21,52 42 40,5 28,94 38 36,5 45,29 11,16 48 46,5 15,85 46 44,5 22,04 44 42,5 29,64 40 38,5 46,38 11,42 50 48,5 16,22 48 46,5 22,56 46 44,5 30,34 42 40,5 47,46 EN 2933:1996 Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 © BSI 12-1999 Table N ± 0,3 Thread code 050 max 54 060 Massa W © BSI 12-1999 Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 Length code 52,5 max 11,68 070 Mass a W max 080 Massa W max 100 Massa W Massa W max 070 70 52 50,5 16,59 50 48,5 23,08 48 46,5 31,03 44 42,5 48,55 072 72 54 52,5 16,96 52 50,5 23,60 50 48,5 31,73 46 44,4 49,64 074 74 56 54,5 17,33 54 52,5 24,12 52 50,5 32,43 48 46,5 50,73 076 76 58 56,5 17,70 56 54,5 24,64 54 52,5 33,13 50 48,5 51,82 078 78 60 58,5 18,07 58 56,5 25,17 56 54,5 33,82 52 50,5 52,90 080 80 62 60,5 18,44 60 58,5 25,69 58 56,5 34,52 54 52,5 53,99 082 82 64 62,5 18,81 62 60,5 26,21 60 58,5 35,22 56 54,5 55,08 084 84 66 64,5 19,18 64 62,5 26,73 62 60,5 35,92 58 56,5 56,17 086 86 66 64,5 27,25 64 62,5 36,62 60 58,5 57,26 088 88 68 66,5 27,77 66 64,5 37,31 62 60,5 58,35 090 90 70 68,5 28,29 68 66,5 38,01 64 62,5 59,43 092 92 72 70,5 28,81 70 68,5 38,71 66 64,5 60,52 094 94 74 72,5 29,33 72 70,5 39,41 68 66,5 61,61 096 96 76 74,5 29,85 74 72,5 40,10 70 68,5 62,70 098 98 78 76,5 30,37 76 74,5 40,80 72 70,5 63,79 100 100 76,5 41,50 74 72,5 64,88 78 ｗｗｗ．ｂｚｆｘｗ．ｃｏｍ 104 104 82 80,5 42,89 78 76,5 67,05 108 108 86 84,5 44,29 82 80,5 69,23 90 88,5 45,68 112 112 86 84,5 71,41 116 116 90 88,5 73,58 120 120 94 92,5 75,76 124 124 98 96,5 77,93 128 128 102 110,5 80,11 132 132 106 104,5 82,29 136 136 110 108,5 84,46 140 140 114 112,5 86,64 144 144 118 116,2 88,82 a Mass quoted in kg/1 000 parts EN 2933:1996 Table Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 01:09, Uncontrolled Copy, (c) BSI EN 2933:1996 Designation EXAMPLE: NOTE If necessary, the code 19005 shall be placed between the description block and the identity block Marking EN 2424, style A, as indicated on Figure Technical specification EN 2583 © BSI 12-1999 Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 01:09, Uncontrolled Copy, (c) BSI blank Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 01:09, Uncontrolled Copy, (c) BSI BS EN 2933:1996 List of references See national foreword © BSI 12-1999 Licensed Copy: UW Swansea ATHENS, University of Wales Swansea, 19/06/2008 01:09, Uncontrolled Copy, (c) BSI BS EN 2933:1996 BSI — British Standards Institution BSI is the independent national body responsible for preparing British Standards It presents the UK view on standards in Europe and at the international level It is incorporated by Royal Charter Revisions British Standards are updated by amendment or revision Users of British Standards should make sure that they possess the latest amendments or editions It is the constant aim of BSI to improve the quality of our products and services We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover Tel: 020 8996 9000 Fax: 020 8996 7400 BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services Tel: 020 8996 9001 Fax: 020 8996 7001 In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service Various BSI electronic information services are also available which give details on all its products and services Contact the Information Centre Tel: 020 8996 7111 Fax: 020 8996 7048 Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards For details of these and other benefits contact Membership Administration Tel: 020 8996 7002 Fax: 020 8996 7001 Copyright Copyright subsists in all BSI publications BSI also holds the copyright, in the UK, of the publications of the international standardization bodies Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained BSI 389 Chiswick High Road London W4 4AL If permission is granted, the terms may include royalty payments or a licensing agreement Details and advice can be obtained from the Copyright Manager Tel: 020 8996 7070