© ISO 2014 Wrought aluminium and aluminium alloys — Sheets, strips and plates — Part 3 Strips Tolerances on shape and dimensions Aluminium et alliages d’aluminium corroyés — Tôles, bandes et tôles épa[.]
INTERNATIONAL STANDARD I SO 63 61 -3 Third edition 01 4-09-1 Wro ught aluminium and aluminium alloys — Sheets , s trip s and p lates — Part : Strip s : To lerances o n s hap e and dimens io ns A lu m in iu m et a llia g es d’a lu m in iu m co rro yés — Tô les, b a n des et tô les ép a isses — Pa rtie : Ba n des: T o léra n ces su r f o rm e et dim en sio n s Reference number ISO 63 61 -3 : 01 4(E) © ISO 01 ISO 63 61-3 :2 014(E) COPYRIGHT PROTECTED DOCUMENT © ISO 2014 All rights reserved Unless otherwise speci fied, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission Permission can be requested from either ISO at the address below or ISO’s member body in the country of the requester ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyright@iso.org Web www.iso.org Published in Switzerland ii © ISO 2014 – All rights reserved ISO 63 61-3 :2 014(E) Contents Foreword Page Scope Dimensional tolerances iv 1 T h i ckn e s s 2 Wi d th Shape tolerances Bibliography © I S O – Al l ri gh ts re s e rve d iii ISO 63 61-3 :2 014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work of preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part In particular the different approval criteria needed for the different types of ISO documents should be noted This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part (see www.iso.org/directives) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights ISO shall not be held responsible for identifying any or all such patent rights Details of any patent rights identi fied during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents) Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement For an explanation on the meaning of ISO speci fic terms and expressions related to conformity assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 79, SC 6, Wro u gh t a lu m in iu m a n d a lu m in iu m Lig h t m eta ls a n d th eir a llo ys , Subcommittee a lloys This third edition cancels and replaces the second edition (ISO 6361-3:2011), which has been technically revised ISO 6361 consists of the following parts, under the general title a llo ys — Sh eets, — — — — — iv strip s a n d p la tes Pa rt : T ech n ica l co n ditio n s f o r in sp ectio n Pa rt 2: Mech a n ica l p ro p ertie s Pa rt 3: Strip s: Pa rt 4: Sh eets a n d p la te s: Pa rt 5: Ch em ica l co m p o sitio n T o lera n ce s o n Wro u g h t a lu m in iu m an d a lu m in iu m : a n d delivery sh a p e a n d dim en sio n s T o lera n ce s o n sh a p e a n d dim en sio n s © ISO 01 – All rights reserved INTERNATIONAL STANDARD ISO 63 61-3 :2 014(E) Wrought aluminium and aluminium alloys — Sheets, strips and plates — Part : Strips: Tolerances on shape and dimensions Scope T his p ar t of I SO 63 61 s p eci fies the tolerances on shap e and dimens ions for wrought aluminium and aluminium al loy s trip by cold-rol l ing for general engineering applications It applies to pro duc ts with thicknes s of over ,1 mm up to, and including 16 mm It es not apply to semi- finished rol led produc ts in coiled form to b e s ubj ec ted to fur ther rol l ing (rerol l s to ck) , or to s p ecial pro duc ts s uch as those that are corrugated or emb os sed Technical conditions for ins p ec tion and deliver y of produc ts covered by this p ar t of I SO 63 61 are s p eci fied in I S O 63 61-1 Dimensional tolerances Thickness T h ic kne s s to l e nc e s s h a l l b e i n ac c o rd a nc e w i th Tab l e s a nd When the tolerance is s p eci fied as either al l plus , or minus s ide, the value in Tab l e , or in Tab l e , shal l b e u b l e d Tolerances for the pro duc ts exceeding the range of s p eci fied thicknes s and width shal l b e agreed up on by the purchaser and the s uppl ier Table — Thickness tolerances D i m e n s i o n s i n m i l l i m e tre s Alloy number Specified thickness 1050, 1050A, 1070, 1070A, 1080, 1080A, 1085, 1100, 1200, 1100A, 1230A, 3003 , 3103, 3203, 3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011 A, 8021, 8079 Specified width U p to a n d O ve r U p to a n d O ver 45 , O ver 0 , O ver 0 , O ver 0 , O ver 0 , i nclud i n g u p to a n d up to a n d u p to a n d u p to a n d up to a n d 45 i nc l u d i n g i nclud i n g i n c l ud i n g i nc l u d i n g i nclud i n g 900 400 800 300 600 i nclud i n g Tolerance ≥ ,1 0,20 ±0,03 ±0,03 ±0,05 0,20 0,25 ±0,03 ±0,0 ±0,05 0,25 ,45 ±0,04 ±0,0 ±0,05 ±0,06 ,45 ,70 ±0,04 ±0,05 ±0,06 ±0,08 ,70 ,9 ±0,05 ±0,05 ±0,06 ±0,09 © I S O – Al l ri gh ts re s e rve d ± ,1 ISO 63 61-3 :2 014(E) Table (continued) Alloy number Specified thickness 1050, 1050A, 1070, 1070A, 1080, 1080A, 1085, 1100, 1200, 1100A, 1230A, 3003, 3103 , 3203 , 3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011 A, 8021, 8079 Specified width O ver Up to and Up to and Over 450, Over 900, i ncludi ng up to and up to and up to and up to and up to and 45 i ncludi ng i ncludi ng i ncludi ng i ncludi ng i ncludi ng 900 40 800 300 600 ±0,13 ±0,15 ±0,20 ±0,20 ±0,23 ±0,23 ±0,28 ±0,33 ±0,38 ±0,43 ±0,58 ±0,76 ±0,25 ±0,30 ±0,38 ±0,43 ±0,51 ±0,66 ±0,89 i ncludi ng Over 400, Over 800, Over 300, Tolerance 0,90 1,1 1,7 1,9 2,4 2,7 3,6 4,5 5,0 6,5 8,0 1,1 1,7 1,9 2,4 2,7 3,6 4,5 5,0 6,5 8,0 11 16 ±0,05 ±0,06 ±0,06 ±0,08 ±0,09 ±0,11 ±0,15 ±0,18 ±0,23 ±0,33 ±0,48 ±0,64 11 ±0,06 ±0,08 ±0,08 ±0,08 ±0,10 ±0,11 ±0,15 ±0,18 ±0,23 ±0,33 ±0,48 ±0,64 ±0,08 ±0,10 ±0,10 ±0,10 ±0,13 ±0,13 ±0,20 ±0,23 ±0,28 ±0,33 ±0,48 ±0,64 ±0,10 ±0,13 ±0,15 ±0,15 ±0,18 ±0,18 ±0,23 ±0,28 ±0,33 ±0,38 ±0,48 ±0,64 Table — Thickness tolerances D imensions in millimetres Alloy number 2014, 2014A, 2017, 2017A, 219, 02 4, 212 4, 618A, 00 4, 310 4, 5021, 502 6, 50 40, 50 42 , 50 49, 5052 , 5059, 5070, 449, 5251, 515 4, 515 4A, 525 4, 53 83 , 45 4, 575 4, 456, 5082 , 5182 , 5083 , 5086, 6016, 6025 , 6061, 6082 , 72 4, 7010, 702 0, 7021, 702 , 7050, 7075 , 7475 , 7178 Specified thickness Specified width Up to O ver a nd i ncludi ng Up to a nd i ncludi ng 45 O ver 450, up O ver 900, up to a nd to a nd i nclud- i nclud- i ng i ng 900 200 O ver O ver O ver O ver O ver O ver O ver O ver O ver up up up up up up up up up to a nd to a nd to a nd to a nd to a nd to a nd to a nd to a nd to a nd i nclud- i nclud- i nclud- i nclud- i nclud- i nclud- i nclud- i nclud- i nclud- i ng i ng ing ing i ng i ng i ng i ng i ng 400 500 70 800 000 10 300 400 600 200, 400, 500, 700, 800, 000, 100, 300, 400, Tolerance ≥ 0,20 0,25 ±0,03 ±0,04 ±0,06 ±0,06 0,25 0,45 ±0,04 ±0,04 ±0,06 ±0,09 0,45 0,70 ±0,04 ±0,05 ±0,06 ±0,09 ±0,10 ±0,10 ±0,10 0,70 0,90 ±0,05 ±0,05 ±0,06 ±0,10 ±0,13 ±0,13 ±0,13 ±0,15 0,90 1,1 ±0,05 ±0,06 ±0,08 ±0,10 ±0,13 ±0,13 ±0,13 ±0,15 1,1 1,7 ±0,06 ±0,08 ±0,10 ±0,13 ±0,15 ±0,15 ±0,15 ±0,18 1,7 1,9 ±0,08 ±0,08 ±0,10 ±0,13 ±0,15 ±0,15 ±0,15 ±0,18 1,9 2,4 ±0,09 ±0,09 ±0,10 ±0,13 ±0,15 ±0,15 ±0,15 ±0,18 ±0,18 ±0,30 2,4 2,7 ±0,10 ±0,10 ±0,13 ±0,13 ±0,18 ±0,18 ±0,18 ±0,20 ±0,20 ±0,41 2,7 3,2 ±0,11 ±0,11 ±0,13 ±0,13 ±0,18 ±0,18 ±0,18 ±0,20 ±0,20 ±0,41 ±0,46 ±0,51 © I SO – All rights reserved ISO 63 61-3 :2 014(E) Table (continued) Alloy number 014, 014A, 2017, 017A, 219, 202 4, 21 4, 618A, 00 4, 310 4, 5021, 502 6, 50 40, 50 42 , 50 49, 5052 , 5059, 5070, 449, 5251, 515 4, 515 4A, 525 4, 53 83 , 45 4, 575 4, 456, 5082 , 5182 , 5083 , 5086, 6016, 6025 , 6061, 6082 , 720 4, 7010, 702 0, 7021, 7022 , 7050, 7075, 7475, 7178 Specified thickness Specified width Up to O ver and i ncludi ng O ver 450, up Up to and i ncludi ng 45 O ver 900, up to and to and i nclud- i nclud- i ng i ng 900 200 O ver O ver O ver O ver O ver O ver O ver O ver O ver up up up up up up up up up to and to and to and to and to and to and to and to and to and i nclud- i nclud- i nclud- i nclud- i nclud- i nclud- i nclud- i nclud- i nclud- i ng i ng i ng i ng i ng i ng i ng i ng i ng 400 500 70 800 000 10 300 40 600 200, 400, 500, 700, 800, 000, 100, 300, 400, Tolerance 3,2 3,6 ±0,11 ±0,11 ±0,13 ±0,13 ±0,18 ±0,25 ±0,30 ±0,33 ±0,36 ±0,41 ±0,46 ±0,51 3,6 4,5 ±0,15 ±0,15 ±0,20 ±0,20 ±0,23 ±0,30 ±0,36 ±0,38 ±0,41 ±0,43 ±0,48 ±0,58 4,5 5,0 ±0,18 ±0,18 ±0,25 ±0,25 ±0,28 ±0,36 ±0,41 ±0,43 ±0,43 ±0,43 ±0,56 ±0,66 5,0 6,5 ±0,23 ±0,23 ±0,28 ±0,28 ±0,33 ±0,41 ±0,46 ±0,46 ±0,46 ±0,46 ±0,61 ±0,71 6,5 8,0 ±0,33 ±0,33 ±0,33 ±0,33 ±0,38 ±0,46 ±0,51 ±0,51 ±0,51 ±0,51 ±0,64 ±0,76 8,0 11 ±0,48 ±0,48 ±0,48 ±0,48 ±0,51 ±0,51 ±0,58 ±0,58 ±0,64 ±0,64 ±0,66 ±0,84 11 16 ±0,64 ±0,64 ±0,64 ±0,64 ±0,64 ±0,64 ±0,64 ±0,76 ±0,76 ±0,76 ±0,89 ±0,89 2 Width Width tolerances shall be in accordance with Table When the tolerance is speci fied as either all plus, or minus side, the value in Table shall be doubled Tolerances for the products exceeding the range of speci fied thickness and width shall be agreed upon by the purchaser and the supplier Table — Width tolerance for strip Dimensions in millimetres Specified thickness O ver Up to and Specified width Up to and Over 150, Over 300, Over 600, Over 200, Over 500, including up to and up to and up to and up to and up to and 150 including including including including including 300 60 200 500 600 ±1,6 ±2,4 ±3,2 ±3,2 including Tolerance ≥ 0,15 3,2 5,0 3,2 5,0 6,3 ±0,3 ±0,3 ±0,4 ±0,4 ±0,5 ±0,8 ±0,8 ±0,8 ±1,2 ±1,2 ±1,6 ±2,4 Shape tolerances The lateral curvature is the depth of the arc for any 000 mm basis lengths (see Figure 1) © ISO – All rights reserved ISO 63 61-3 :2 014(E) Key a deviation from straightness (maximum value) b width c 000 mm Figure — Lateral curvature of strip When tested with the strip resting on a flat surface, against a straight edge, the lateral curvature shall not exceed the values given in Table for a value of length L=2 000 mm The maximum value for the products exceeding the range of speci fied thickness and width shall be agreed upon between the purchaser and the supplier Table — Lateral curvature tolerances for strip Dimensions in millimetres Specified thickness Specified width 15 or over, O ver Up to and including up to and up to and Over 25, up to and Over 50, Over 100, Over 250, including 25 including 50 including 10 including 250 including 60 Maximum value ≥ 0,15 1,6 1,6 3,2 19 15 up to and up to and (in any 000 length) 10 10 © ISO 01 – All rights reserved ISO 63 61-3 :2 014(E) Bibliography [1] I SO 63 61-1 , Wro u gh t a lu m in iu m a n d a lu m in iu m a lloys — Sh eets, strip s a n d p la tes — Pa rt : T ech n ica l co n ditio n s f o r in sp ectio n © ISO 2014 – All rights reserved a n d delivery ISO 63 61-3 :2 014(E) ICS 77.150.10 Price based on pages © ISO 2014 – All rights reserved