© ISO 2016 Textile machinery and accessories — Rings and travellers for ring spinning and ring twisting frames — Part 1 Flange rings T and SF and their travellers Matériel pour l’industrie textile — A[.]
INTERNATIONAL STANDARD ISO 96-1 Third edition 2016-11-15 Textile machinery and accessories — Rings and travellers for ring spinning and ring twisting frames — Part 1: Flange rings T and SF and their travellers Matériel pour l’industrie textile — Anneaux et curseurs pour machines filer et retordre — Partie 1: Anneaux T et SF et leurs curseurs Reference number ISO 96-1:2016(E) © ISO 2016 ISO 96-1:2016(E) COPYRIGHT PROTECTED DOCUMENT © ISO 2016, Published in Switzerland All rights reserved Unless otherwise specified, no part o f this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission Permission can be requested from either ISO at the address below or ISO’s member body in the country o f the requester ISO copyright o ffice Ch de Blandonnet • CP 401 CH-1214 Vernier, Geneva, Switzerland Tel +41 22 749 01 11 Fax +41 22 749 09 47 copyright@iso.org www.iso.org ii © ISO 2016 – All rights reserved ISO 96-1:2016(E) Contents Page Foreword iv Scope Normative references Terms and definitions Principal dimensions of T- and SF-rings Travellers Designation of travellers © ISO 2016 – All rights reserved iii ISO 96-1:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work o f preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o f electrotechnical standardization The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part In particular the different approval criteria needed for the di fferent types o f ISO documents should be noted This document was dra fted in accordance with the editorial rules of the ISO/IEC Directives, Part (see www.iso.org/directives) Attention is drawn to the possibility that some o f the elements o f this document may be the subject o f patent rights ISO shall not be held responsible for identi fying any or all such patent rights Details o f any patent rights identified during the development o f the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents) Any trade name used in this document is in formation given for the convenience o f users and does not constitute an endorsement For an explanation on the meaning o f ISO specific terms and expressions related to formity assessment, as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html The committee responsible for this document is ISO/TC 72, Textile machinery and accessories, Subcommittee SC 1, Spinning preparatory, spinning, twisting and winding machinery and accessories This third edition cancels and replaces the second edition (ISO 96-1:2009), of which it constitutes a minor revision with the following changes: a) full height h1 in Figure given; b) full height h in Figure given; c) value o f flange width b2 in Table changed; d) new value of for height h1 and h in Table inserted; e) flange width b1 in Figure removed and adapted to Figure 4; f) Clause editorially revised A list of all parts in the ISO 96 series can be found on the ISO website iv © ISO 2016 – All rights reserved INTERNATIONAL STANDARD ISO 96-1:2016(E) Textile machinery and accessories — Rings and travellers for ring spinning and ring twisting frames — Part 1: Flange rings T and SF and their travellers Scope T h i s c ument s p e c i fie s the pri ncip a l d i men s ion s o f T- and S F-ri ngs , and the mas s and tolerance on the ma s s , o f the appropri ate travel lers for fla nge ri ngs employe d on ri ng s pi nn i ng and ri ng twi s ti ng mach i ne s I t a l s o s p e c i fie s the me tho d o f de s ignation o f the travel lers Normative references T he fol lowi ng c u ments are re ferre d to i n the tex t i n s uch a way th at s ome or a l l o f thei r content s titute s re qu i rements o f th i s c u ment For date d re ference s , on ly the e d ition cite d app l ie s For u ndate d re ference s , the late s t e d ition o f the re ference d c ument (i nclud i ng a ny amend ments) appl ie s ISO 3, Preferred numbers — Series of preferred numbers Terms and definitions No term s and defi nition s a re l i s te d i n th i s c u ment ISO and IEC maintain terminological databases for use in standardization at the following addresses: — IEC Electropedia: available at http://www.electropedia.org/ — ISO Online browsing platform: available at https://www.iso.org/obp/ Principal dimensions of T- and SF-rings The principal dimensions of T- and SF-rings are illustrated in Figures and , and s p e ci fie d i n Table Figure — Example of a T-ring © ISO 2016 – All rights reserved ISO 96-1:2016(E) Figure — Example of an SF-ring Table — Ring dimensions Inside diameter d Height T-Ring Fitting diameter h1 d1 b1 nominal tolerance a a b c d 36 38 40 42 45 48 (50) 51 54 (55) 57 60 63 (65) 70 75 10 Flange width +0,15 Dimensions in millimetres Height SF-Ring Fitting diameter h2 d2 10 The tolerance refers to the diameter d1 –0,25 , re s p e c ti ve l y +0,2 − ,1 –0,2 2,6b 3,2 c 4d d+ b2 nominal tolerance a –0,2 Flange width 10 12 d + 12 2,8 3,8 –0,25 d2 , e xclud i n g a ny o va l it y T he fl a n ge width b1 = , m m wa s de s i g n ate d p re vio u s l y a s r i n g fl a n ge N o /2 T he fl a n ge width b1 = , m m wa s de s i g n ate d p re vio u s l y a s r i n g fl a n ge N o T he fl a n ge width b1 = m m wa s de s i g n ate d p re vio u s l y a s r i n g fl a n ge N o © ISO 2016 – All rights reserved ISO 96-1:2016(E) Travellers 5.1 Examples of travellers appropriate for T- and SF-rings are shown in Figures and Figure — Example of a traveller for a T-ring in the running position Figure — Example of a traveller for an SF-ring in the running position The values for traveller mass are given in Table Traveller mass is taken from the R20 series of preferred numbers in accordance with ISO The range of traveller mass comprises values from to 900 inclusive 5.2 T he travel ler mas s repre s ents the nom i na l ma s s , i n gra m s , o f 0 travel lers o f the s ame typ e T he tolerance on the nom i na l mas s © ISO 2016 – All rights reserved for 0 travel lers o f the s a me typ e i s ± % ISO 96-1:2016(E) Table — Traveller mass Mass of traveller 4,5 5,6 6,3 7,1 10 11,2 12,5 14 16 18 20 22,4 (grams per 000 travellers) 25 28 31,5 35,5 40 45 50 56 63 71 80 90 100 112 125 140 160 180 200 224 250 280 315 355 400 450 500 560 630 710 800 900 Designation of travellers The designation on the packing of travellers for the T- and SF-ring includes the following information: a) the denotation “Traveller” (optional); b) a reference to this document, i.e ISO 96-1 (optional); c) the s ymb ol “T ” or “S F ” (op tiona l) ; d) the flange width, e) the manu fac tu rer ’s de s ignation f) the wi re s e c tion s ymb ol (i f appl ic able) , e g “ f ”, “r ” (“ f” = fl at, “r ” = rou nd) ; b1 , in millimetres, of the appropriate ring (optional); for the travel ler s tyle (e g “C ”, “E L” ) ; g) the traveller mass (see Table 2); h) the traveller material or traveller name if it is other than steel (where this information is omitted, it is assumed that the traveller material is steel); i) the s u r face fi n i s h (op tiona l) ; j) the app e ara nce (op tiona l) © ISO 2016 – All rights reserved ISO 96-1:2016(E) ICS 9.1 0.1 Price based on pages © ISO 2016 – All rights reserved