Using urban morphology for flood risk in residential areas in ho chi minh city

Untitled SCIENCE & TECHNOLOGY DEVELOPMENT, Vol 19, No K4 2016 Trang 146 Using urban morphology for flood risk in residential areas in Ho Chi Minh city  Le Thanh Hoa  Nguyen Thi Phuong Chau Universit[.]

SCIENCE & TECHNOLOGY DEVELOPMENT, Vol 19, No K4-2016 Using urban morphology for flood risk in residential areas in Ho Chi Minh city  Le Thanh Hoa  Nguyen Thi Phuong Chau University of Social Sciences and Humanities, VNU-HCM, Vietnam (Manuscript Received on July 04th, 2016, Manuscript Revised August 18rd, 2016) ABSTRACT: Urban morphology in urban studies is used to classify and manage the distribution of urban densities In urban planning, it helps to identify the emerging problems and solve the disorder of urban functions as in the megacity of Ho Chi Minh City Rapid urbanization has increased the development footprint with disordered densities of building footprint, incomplete infrastructure and urban - peripheral instability And it, then, caused more flood problems to the city This study was based on applying fractal geometry, GIS on large-scale maps for identifying residential density based on urban morphology The land-use map and the building footprints map of 2010 were integrated in fractal geometry to analyze the distribution of urban areas by the large scale of GIS data This study showed HCMC had problems on irrational development in residential densities areas; and uneven development of population and residential density between the urban areas At block scale of land-use block, in urban center had highest densities of building footprints and population, then, the medium densities in developing districts and rural-sub-districts With these densities, there was more flood in high density areas, as in urban center, and less flood in lower density areas, as in sub-urban areas These problems may cause some limitations to development of social, commercial, industrial, and infrastructure in HCMC City needs to have flood control and management for development of the city Keywords: Urban morphology analysis, development footprint, building footprint, residential density, flood risk INTRODUCTION 1.1 Urbanization and urban problems in Ho Chi Minh City Ho Chi Minh City (HCMC) is still the largest city of Vietnam in education, science, economies of industries and services, etc and has international relations To this foundation, HCMC has increasingly received many Trang 146 immigrants from provinces and even outside country for educating, researching, and working, etc Thus, landuse changed along with the expansion of development footprint due to urbanization These have caused many problems in urban area as environmental quality and close link to climate change and flooding (OECD, 2014) TẠP CHÍ PHÁT TRIỂN KH&CN, TẬP 19, SOÁ K4-2016 1.2 Increasing of development footprint and flooding problems HCMC with high population rate requires more land for housing and residential areas The dynamic urbanization has resulted in uneven spatial development of urban areas, such as over density in urban center with more housing and buildings, disorder density in developing and sub-urban areas; and high density in risk areas as in low-land areas The densities of residential areas refer to the increasing of building-footprint densities and other non-building facilities of the areas They have close relationship to urban flooding The previous researches showed in high density residential areas had more flooding problem than the lower density areas, high flood in the center rather than in developing and suburban areas Urban morphology can help to solve the problems of development footprint density and disorganization Along with fractal geometry analyses, that urban morphology can identify the trend of urbanization and expansion flow of development footprint (Longley and Messev, 2002) In relationship of residential density to flooding, it helps to understand the flows and trends of residential expansion and flooding patterns It also shows the development patterns of development footprint of the city It is necessary for urban planning and management to solve the urban problems MATERIALS AND METHODS Development footprint refers to the enlargements of housing and residential areas, infrastructure and urban services, and other nonbuilding facilities And building footprint refers to the site that is used by the build-up areas To analyze the relationship of residential expansion and density to flooding by urban morphology, it needs to have the concepts of density and the density measures for urban residential areas The density measures for the residential area excluding the non-local residential areas such as parks, schools, and open space, etc are widely accepted in residential planning (Forsyth, 2003; Hess et al., 2007) Other widely accepted measure is to distinguish between gross density and net density of residential area The gross residential density includes all the above land uses plus regional uses such as education, open space, commercial uses and transport; while net residential density includes the residential component plus local roads (Landcom, 2011) In identifying the residential density in urban morphology map, density is usually calculated by dividing an overlapping of the built-up area on land-use This calculation must be localized and referenced by the real surface of land-use (e.g the total area of the land-use) This research used net density definition for residential area In urban area, special in HCMC, the residential areas are developed on land-use block Then, there are the net residential density on land-use block, the housing/building types on land-use block, and the residential population including person and household size on land-use block, etc (Forsyth, 2003) From then, the net density is analyzed at the block level either as a measure of total buildings per block or as other statistical evaluates of residential amount per block level Urban morphology analysis in this study was to analyze the residential density on the three indicators: number of building footprints, the land-use area per hectare and population density per land-use block (or block level) Furthermore, fractal geometry was helped to identity the density of building footprints on land-use block From then the density distribution in different urban residential areas were analyzed and compared the flood risk areas Trang 147 SCIENCE & TECHNOLOGY DEVELOPMENT, Vol 19, No K4-2016 Table The standard of residential density ranges for the study area Category Residential density category Number of building footprints (per ha) High residential density Over 50 building footprints per Medium residential density From 20 to 50 building footprints per Low residential density Below 20 building footprints per Source: Department of Planning - Western Australian Planning Commission (2012) To classify the distribution of residential density on HCMC urban morphology map, this study applied the category of residential density of Western Australian Planning Commission (2012) This category was with residential density analysis in high-, medium-, and lowlevels (UN-Habitat, 2004; Landcom, 2011) (see Table 1) 2.1 Data set for urban residential density analysis - Using GeoEye and Worldview-2 images of 2010 combine with cadastral map 1/2,000 scale (Source: HCMC DoNRE, 2010) to interpret and classify the building footprints map - Using Land-use 2010 with 1/25,000 scale (Source: HCMC DoNRE) - Population census commune (Source: HCMC Statistical Office) 2010 The input land-use and primary map data were sourced by the Department of Resources and Environment (DoNRE) in 2010 with the scale of 1/25,000 They were for analyzing the residential area Building footprint data was supported by the HCMC Construction Department for mapping the building footprints map (1/2,000) which was updated on the GeoEye and Worldview-2 images And the number and type of land-use classes chosen in research correspond to the spatial scale of preparatory building footprints used in urban morphology map Population data, in the form of statistical available for each municipal commune in the city’s annual statistic, was Trang 148 integrated to the building footprint of the residential land-use cover The population density was linked to building footprint density to show the density problems of residential areas Flood data from HCMC Steering Center of the Urban Flood Control Program (SCFC) and from HCMC Department of Transportation were integrated into base map to produce flood map Then, the multi-criteria analysis technique in GIS was applied to integrated residential densities on land-use blocks in flooded area to analyze the relationship of residential density to flooding problems in HCMC 2.2 Urban morphology and fractal geometry methods Fractal geometry in urban morphology analysis is used to count the identification of residential densities based on Arcview 3.2 with a grid cell size of 1×1m and by Avenue program for urban morphology tool These criteria of urban densities were either derived directly from the morphology map information of 2010 Based on fractal analyses, the scales of residential densities were founded The residential density of land-use blocks provided information on the concentration of the number of building types per land-use units Then the built-up coverage ratio was computed These results were used to evaluate the density levels and relate to spatial distribution in the urban area of HCMC In the science of fractal geometry, Batty and Kim (1992) had analyzed the fractal geometry to identify the residential TẠP CHÍ PHÁT TRIỂN KH&CN, TẬP 19, SOÁ K4-2016 density on land-use block Therefore, this study applied the Batty and Kim’s fractal formula to identify residential densities to HCMC The formula is the following: D = lnN(R) / ln(r) (1) Where: N(R) is the count of buildings of each building type overlapping the feature of block (per unit area of building types, in square meters) - r is perimeter meters of land-use block In this case lnN(R) refers the density of each building type of land-use block, and ln(r) is the size of land-use blocks (block of an observation) D is the fractal geometry With the formula 1, the fractal geometry “D” can measure a rate of the identity distribution of mean building count of a block as block density, and the constant k is 1.0 related to the mean connection of urban morphology map areas of land-use blocks; Uco = total residential areas of commune To estimate the residential population densities of land-use block based on the result of equation 3, it can be calculated as follows: PRD = Pbl / UR (3) Where: PRD = residential population densities; UR = areas of building footprints Based on the equations 2-3 of method, research used GIS data of people living and building types within communes to estimate the number of people in a smaller area within the land-use block, or an area This is defined as “the transfer of data from one set (source units) to a second set (target units) of overlapping, nonhierarchical, areal units Area interpolation is closely related to population densities on each block (Langford et al., 1994) The value D is as the parameter to measure the identity of building types, residential density, and the values of built-up density on land-use block When the D value is larger, the density on land-use block is larger as well as the identity of each building type (the same construction the number of building type on block) And D can explain the level of block for the most complex, cumulation of the number of building types with plane-filling perimeters as well The analysis results of fractal geometry of this study were categorized in three degrees of residential density based on the category on Table Population values of land-use block were calculated from census data at the commune level The general equation can be written as follows: Pbl = Pco * Ubl / Uco (2) Where Pbl = population of land-use block; Pco = population communes; Ubl = residential Figure The method framework of urban morphology analysis of urban residential density in HCMC An illustrated methodology was described in Figure This methodology consisted of the population data, land-use, and building footprints layers Those were input in the Trang 149 SCIENCE & TECHNOLOGY DEVELOPMENT, Vol 19, No K4-2016 computer as the codes in the binary system (with was unoccupied, and was occupied) This binary system was presented in one matrix and was analyzed by fractal geometry for counting profiles RESIDENTIAL DENSITY IN HO CHI MINH CITY 3.1 Building footprints density in residential areas The building footprint map and fractal geometry analysis result provided the spatial distribution of building footprints in HCMC Applied with the category of residential density in Table 1, the spatial density analyzed by program tool in fractal geometry analysis had showed the results of residential densities in HCMC in the below Table and Figure The numbers of buildings in these zones were nearly the same, but the area of land-use blocks is different Therefore, there were big differences of buildings densities among three buildings zones – zone A (high density), zone B (medium density), and zone C (low density) Zone A had buildings density three times higher than of zone B, and eight times higher than of zone C But the building areas were in converse, the area of zone A was about three times less than zone B and eight times less than zone C Figure Urban Morphology Map of HCMC in 2010 3.2 Population density on residential areas There was the relationship between building footprint densities to population densities in HCMC The high density of buildings refers to high density of population And conversely, the lower density of buildings refers to lower density of population living in residential areas Figure showed The very high population density of residential area has caused so many problems of drainage system and high sealed zone in the center, and led the serious problems of flooding in rainy season The D value of fractal geometry had estimated 1.31 to 1.67 synonymous with urban densities and buildings D index in zone A was highest, then zone B and C, respectively Corresponding density profiles for nearly the same were shown 1.7 for residential area to 1.8 for build-up area of Longley & Messev (2001) The map showed the highest residential density of zone A concentrated in the urban center And the lower densities of zone B and C were in developing districts Trang 150 Figure Population densities on land-use block of HCM in 2010 TẠP CHÍ PHÁT TRIỂN KH&CN, TẬP 19, SỐ K4-2016 Table Dimensions associated with partial building densities Range Zone Area (ha) Number of building footprints Building footprints density (#/ha) ln(area) Dimensions D High A 1,721.22 260,245 151 7.45 1.67 Medium B 5,413.64 268,701 49 8.60 1.45 Low C 14,022.73 273,131 19 9.55 1.31 21,157.59 802,077 Total RESIDENTIAL DENSITIES AND FLOODING PROBLEMS IN HO CHI MINH CITY Table Flooding risk on urban residential areas Residential areas Rain (ha) Rain & Tide (ha) Tide (ha) Urban highdensity residential area 322.25 8.93% 212.68 5.89% 203.49 5.64% Urban mediumdensity residential area 1136.18 17.27% 124.58 1.89% 321.30 4.88% Urban lowdensity residential area 501.59 6.18% 109.07 1.34% 276.83 3.41% New urban development residential area 71.92 1.71% 7.82 0.19% 274.68 6.54% Rural mediumdensity residential area 29.74 0.98% - 6.78 0.22% Rural lowdensity residential area - - 5.70 0.10% Total 2,061.69 454.14 1,088.77 Flooding problem in HCMC was illustrated in table In the high-density residential areas of urban area, flood covered about 20.5 percent of total 3,606 hectares In medium-density residential areas, flood covered about 24 percent of total 6,578 hectares And in lower-density residential areas, flooded area covered about 10.9 percent of about 8,000 hectares The least flooded area was in the rural areas with just from to less than percent of total This result gave some significant information about flooding in HCMC, that flooding in this city was not strongly related to the terrain, but to development footprint and its density (as the density of residential areas-building footprints, and density of population) CONCLUSIONS AND SUGGESTIONS Urban morphology and geometry technique were used to identify the densities on urban residential areas in HCMC The results of this research is to better understand the spatial distribution problems through the relationship between residential density areas, building footprint density, population density, and flooding The big differentiation of urban residential densities between zone A, zone B, and zone C showed the uneven distribution of residential density in urban area of HCMC It caused many problems in provisioning the urban infrastructure and urban services, and distribution of open space and green space The flood reason was not strongly depended on terrain, but by urbanization and development process The city government and urban planners may consider in encouraging the moving of people in zone A with very high residential density out to zone C or B, especially zone C with low residential density Results of urban morphology analyses: the urban and rural residential densities at the detail Trang 151 SCIENCE & TECHNOLOGY DEVELOPMENT, Vol 19, No K4-2016 levels of the land-use block and building footprints; the area with high population density had high densities of building footprints In contrast, the area with low population density had low densities of building footprints Urban morphological analysis to flooding showed in center-districts: flood was concentrated in highand medium-density built-up residential areas Sử dụng hình thái thị phân tích nguy ngập lụt khu dân cư Tp Hồ Chí Minh  Lê Thanh Hòa  Nguyễn Thị Phượng Châu Trường Đại học Khoa học xã hội & Nhân văn, ĐHQG-HCM TĨM TẮT Hình thái đô thị sử dụng để xếp quản lí mật độ thị Nó giúp xác định giải bất ổn khu vực chức đô thị lãnh vực qui hoạch thành phố lớn thành phố Hồ Chí Minh (TPHCM) Đơ thị hóa làm gia tăng nhanh dấu hiệu phát triển không gian với mật độ xuất dấu vết xây dựng lộn xộn khu dân cư Cùng với sở hạ tầng không đầy đủ liên kết đô thị - nông thôn không bền vững gây nên vấn đề ngập lụt nhiều cho thành phố Nghiên cứu sử dụng tốn hình học fractal, ứng dụng kỹ thuật GIS dựa đồ tỉ lệ lớn phân tích hình thái thị để xác định mật độ khu dân cư Bản đồ sử dụng đất đồ dấu vết xây dựng đưa vào hình học fractal để phân tích phân bố dân cư năm 2010 Nghiên cứu cho thấy TPHCM có vấn đề phát triển khơng hợp lí mật độ khu dân cư phát triển không đồng khu vực chức đô thị đơn vị sử dụng đất, thể qua mật độ xây dựng, mật độ dân số cao khu dân cư trung tâm, mật độ trung bình khu dân cư phát triển, quận, huyện ven Với tình trạng này, vân đề ngập lụt diễn nhiều khu vực mật độ dân cư cao, khu vực có mật độ dân cư thấp Các vấn đề làm hạn chế phát triển kinh tếxã hội, thương mại, công nghiệp, sở hạ tấng đô thị Từ khóa: Phân tích hình thái thị, dấu hiệu phát triển, dấu vết xây dựng, mật độ dân cư, ngập lụt REFERENCES [1] Batty M., Kim K., Form Follows Function: Reformulation Urban Population Density Function Urban Trang 152 Studies, 29, 1043-1069, 1992 10.1080/00420989220081041 Doi: TẠP CHÍ PHÁT TRIỂN KH&CN, TẬP 19, SỐ K4-2016 [2] Forsyth A., Measuring Density: Working Definition for Residential Density and Building Density, Design Center for American Urban Landscape Design Brief University of Minnesota 2-6, 2003 Retrieved from http://www.corridordevelopment.org [3] Hess P., Sorensen A., Parizeau K., Urban Density in the Greater Golden Horseshoe Research paper 209, 2007 Retrieved from the University of Toronto, Centre for Urban and Community Studies Web site: http://www.urbancentre.utoronto.ca [4] Landcom, Residential Density Guide 2011 The Landcom Project Teams: Author Retrieved from http://www.landcom.com.au/downloads [5] Langford M., Unwin D J., Generating and Mapping Population Density Surfaces Within a Geographical Information System, The Cartographic Journal, 31 (1), 21-26, 1994 [6] Longley P A., Mesev T V., Measurement of Density Gradients and Space Filling in Urban Systems Regional Science Association, 81 (1), 1-28, 2002 [7] Longley P A., Mesev T V., Measuring Urban Morphology Using remote Sensing Image Remote Sensing and Urban Analysis GIS data London and New York: Taylor and Francis Group, 2001 [8] OECD, Cities and climate change Policy perspectives National governments enabling local action, 2014 Retrieved from https://www.oecd.org [9] UN-Habitat (United Nations Human Settlements Programme), Urban Patterns for a Green Economy Leveraging Density UN-Habitat, 2004 Retrieved from http://www.unhabitat.org/categories [10] Western Australian Planning Commission, Residential Design Codes of Western Australia Explanatory Guidelines 2012 Department of Planning, 2012 Retrieved from http://www.planning.wa.gov.au/ Trang 153 ... Total RESIDENTIAL DENSITIES AND FLOODING PROBLEMS IN HO CHI MINH CITY Table Flooding risk on urban residential areas Residential areas Rain (ha) Rain & Tide (ha) Tide (ha) Urban highdensity residential. .. development of urban areas, such as over density in urban center with more housing and buildings, disorder density in developing and sub -urban areas; and high density in risk areas as in low-land areas. .. This binary system was presented in one matrix and was analyzed by fractal geometry for counting profiles RESIDENTIAL DENSITY IN HO CHI MINH CITY 3.1 Building footprints density in residential areas