Phần sơ đồ mạch điện G 1 4 MPI KAPPA > Body Electrical System > Smart key System > Smart key unit > Schematic Diagrams Circuit diagram No Connector A(26 pins) No Connector B(16 pins) No Connector C(22.
Phần sơ đồ mạch điện G 1.4 MPI-KAPPA > Body Electrical System > Smart key System > Smart key unit > Schematic Diagrams Circuit diagram Conne N Connecto N ctor Connector o r B(16 o A(26 C(22 pins) pins) pins) No V BAT_LO AD C_CAN_L O_SSB_illum ination_GN D O_ESCL _GND C_CAN_H O_IMMO_IN D Power_ GND1 - A-IGN1 - L_Stop O_Interior_a lamp fuse ntenna #2_Power A_IGN1 _Relay A_ACC O_IMMO_a ntenna_po wer - A_IGN O_ESCL_en able - SSB switch L_Brake switch O_Interior_a ntenna #1_Power F_Wheel speed O_Trunk_an tenna_powe r L_DRV toggle button O_bumper_ antenna_po wer - 10 - L_ESCL_unl O_RH_side_ ock antenna_po wer 11 ESCL_C O_exterior O_LH_side_ OM buzzer antenna_po wer 12 B_CAN_ L_P O_SSB_LED_ H position/L_ BLUE Clutch switch 13 B_CAN_ L_start O_SSB_illum L feedback ination_pow er 14 VBAT_C O_IMMO_a PU ntenna_GN D 15 O_ESCL _BAT 16 POWER O_SSB_LE O_interior_a _GND2 D_AMBER ntenna#1_ GND DIAG-K - O_interior_a ntenna#2_ GND 17 O_Start er_rela y - 18 O_IGN2 _relay - 19 O_ACC_ relay O_trunk_ant enna_GND 20 - O_bumper_ antenna_GN D 21 L_Trunk lid_Swit ch O_RH_side_ antenna_GN D 22 - O_LH_side_ antenna_GN D 23 F_RPM 24 EMS_C OM 25 L_SSB_ Switch 26 L_ASTto ggle button Phần sửa chữa G 1.4 MPI-KAPPA > Body Electrical System > Smart key System > Smart key unit > Repair procedures Inspection Smart Key Unit - Refer to the Smart Key Switch - Refer to the Antenna BE group - inspection / self diagnosis with GDS BE group - inspection / self diagnosis with GDS - Refer to the BE group Trunk Lid Open Switch - inspection / self diagnosis with GDS Check for continuity between the Trunk lid open switch terminals If continuity is not specified, inspect the switch Removal - Take care not to scratch the crash pad and related parts Smart key unit Disconnect the negative(-) battery terminal Remove the glove box (Refer to Body (Interior and Exterior) - "Crash Pad") Remove the smart key unit (A) after disconnecting the connector and loosening the mounting nuts (2EA) and a bolt Interior Antenna - Take care not to scratch the crash pad and related parts Disconnect the negative(-) battery terminal Remove the console (Refer to Body (Interior and Exterior) - "Console") Remove the interior antenna (A) after disconnecting the connector and loosening the mounting bolts (2EA) Interior Antenna Disconnect the negative(-) battery terminal Remove the console (Refer to Body (Interior and Exterior) - "Console") Take care not to damage and scratch the console and its related parts Apply the protective tapes to the console and its related parts Disconnect the interior antenna connector, then remove the interior antenna (A) after loosening screws (2EA) Trunk Antenna Disconnect the negative (-) battery terminal Remove the trunk transverse trim (A) Disconnect the trunk antenna connector (A) and remove the trunk antenna (B) after loosening nuts (2EA) Exterior Bumper Antenna Disconnect the negative (-) battery terminal Remove the rear bumper (Refer to Body (Interior and Exterior) - "Rear bumper") Disconnect the antenna connector (B) and remove the exterior bumper antenna (A) after loosening the screws (2EA) Buzzer Disconnect the negative (-) battery terminal Remove the left side wheel guard Remove the external buzzer (A) after disconnecting the connector Door Outside Handle Disconnect the negative (-) battery terminal Remove the front door module (Refer to Body (Interior and Exterior) - "Front Door") After loosening the mounting bolt, then remove the outside handle cover (A) 4 Remove the outside handle (A) by sliding it rearward Disconnect the outside handle connector Trunk lid open switch Disconnect the negative (-) battery terminal Remove the trunk door trim (Refer to Body (Interior and Exterior) - "Trunk") Disconnect the trunk lid open switch connector (A) Remove the trunk open switch (A) from the trunk garnish Installation Smart Key Unit Install the smart key unit Install the smart key unit mounting nuts and connector Install the glove box housing Install the glove box Install the negative (-) battery terminal and check the smart key system Interior Antenna Install the interior antenna Install the console Install the negative (-) battery terminal and check the smart key system Interior Antenna Install the interior antenna Install the console Install the negative (-) battery terminal and check the smart key system Trunk Antenna Install the trunk antenna Install the trunk transverse trim Install the negative (-) battery terminal and check the smart key system Exterior Bumper Antenna Install the exterior bumper antenna Install the rear bumper Install the negative (-) battery terminal and check the smart key system Buzzer Install the buzzer Install the left side wheel guard Install the negative (-) battery terminal and check the smart key system Trunk Lid Open Switch Install the trunk lid open switch Install the trunk trim Install the negative (-) battery terminal and check the smart key system Door Outside Handle Install the outside handle Install the door trim Install the negative (-) battery terminal and check the smart key system PHẦN LƯU MÃ CODE CHÌA (CÀI CHÌA) G 1.4 MPI-KAPPA > Body Electrical System > Smart key System > Smart key > Repair procedures Smart Key Smart Key Code Saving Connect the DLC cable of GDS to the data link connector in driver side crash pad lower panel, turn the power on GDS 2 Select the vehicle model and then "Smart key code saving" After selecting "Smart key teaching" menu, push "Enter" key, then the screen will be shown as below 4 After pushing the teaching key to SSB, push "ENTER" key Input the "Pin code" for first key teaching 6 Confirm the message "First key teaching completed" 7 Input the "Pin code" for second key teaching 8 Confirm the message "Second key teaching completed" Then the screen will be shown as below when key teaching process is completed PHẦN KIỂM TRA 2G SMART KEY unit problem : communication diagnosis 1.4 MPI-KAPPA > Body Electrical System > Smart key System > Repair procedures SMART KEY unit Output problem : antenna and switch output Inspection diagnosis Self Diagnosis With GDS Switch Diagnosis Smart key system defects can diagnosed with GDS GDS Connect the cable of GDS tobe thequickly data link connector in the driver side operates actuator quickly to monitor, input/output value and self crash pad lower panel, turn the power on GDS diagnosis Select the vehicle model and SMART KEY system The following three features willthen be major problem in SMART KEY system Problem in SMART KEY unit input Problem in SMART KEY unit Problem in SMART KEY unit output The following three diagnostic solutions will be the main solution process to a majority of concerns SMART KEY unit Input problem : switch diagnosis Select the "SMART KEY unit" After IG ON, select the "Current data" 5 You can see the situation of each switch on scanner after connecting the "current data" process Display Description FL Toggle switch ON : Push button is ON in the driver door handle FR Toggle switch ON : Push button is ON in the assist door handle Trunk switch Gear P Position IGN ACC Push Knob switch External Buzzer ON : Trunk button is ON ON : Shift lever is P position ON : IGN switch is IG position ON : IGN switch is ACC position ON : Push knob switch is ON ON : Buzzer is ON Communication Diagnosis With GDS (Self Diagnosis) Communication diagnosis checks that the each linked components operates normal Connect the cable of GDS to the data link connector in driver side crash pad lower panel After IG ON, select the "DTC" Antenna Actuation Diagnosis Connect the cable of GDS to the data link connector in driver side crash pad lower panel After IG ON, select the "ACTUATION TEST" 3 Set the smart key near the related antenna and operate it with a GDS If the LED of smart key is blinking, the smart key is normal If the LED of smart key is not blinking, check the voltage of smart key battery Antenna actuation A INTERIOR Antenna B INTERIOR Antenna C Trunk antenna D BUMPER/Antenna E DRV_DR Antenna F AST_DR Antenna Antenna Status Check Connect the cable of GDS to the data link connector in driver side crash pad lower panel Select the "Antenna Status Check" 3 After IG ON, select the "Antenna Status Check" Set the smart key near the related antenna and operate it with a GDS ... model and SMART KEY system The following three features willthen be major problem in SMART KEY system Problem in SMART KEY unit input Problem in SMART KEY unit Problem in SMART KEY unit output... the smart key near the related antenna and operate it with a GDS If the LED of smart key is blinking, the smart key is normal If the LED of smart key is not blinking, check the voltage of smart. .. chữa G 1.4 MPI-KAPPA > Body Electrical System > Smart key System > Smart key unit > Repair procedures Inspection Smart Key Unit - Refer to the Smart Key Switch - Refer to the Antenna BE group -