ACS310 drives user''''s manual ABB drives User’s manual ACS310 drives List of related manuals You can find manuals and other product documents in PDF format on the Internet See section Document library o[.]
ABB drives User’s manual ACS310 drives List of related manuals Drive hardware manuals and guides ACS310 short form user’s manual ACS310 user’s manual Option manuals and guides MFDT-01 FlashDrop user’s manual MREL-01 relay output extension module user's manual for ACS310/ACS350 MUL1-R1 installation instructions for ACS150, ACS310, ACS350 and ACS355 MUL1-R3 installation instructions for ACS310, ACS350 and ACS355 MUL1-R4 installation instructions for ACS310 and ACS350 SREA-01 Ethernet adapter module quick start-up guide SREA-01 Ethernet adapter module user’s manual Option manuals and guides Guide for capacitor reforming in ACS50, ACS55, ACS150, ACS310, ACS350, ACS355, ACS550 and ACH550 Code (English) 3AUA0000044200 3AUA0000044201 3AFE68591074 3AUA0000035974 3AFE68642868 3AFE68643147 3AUA0000025916 3AUA0000042902 3AUA0000042896 3AFE68735190 You can find manuals and other product documents in PDF format on the Internet See section Document library on the Internet on the inside of the back cover For manuals not available in the Document library, contact your local ABB representative User’s manual ACS310 Table of contents Safety Mechanical installation Electrical installation Start-up and control with I/O © 2011 ABB Oy All Rights Reserved 3AUA0000044201 Rev C EN EFFECTIVE: 2011-12-13 Table of contents Table of contents List of related manuals Safety What this chapter contains Use of warnings Safety in installation and maintenance Electrical safety General safety Safe start-up and operation General safety Safety 15 15 16 16 17 17 17 Introduction to the manual What this chapter contains Applicability Target audience Purpose of the manual Contents of this manual Related documents Categorization by frame size Terms and abbreviations Quick installation and commissioning flowchart 19 19 19 19 20 21 21 21 22 Operation principle and hardware description What this chapter contains Operation principle Product overview Layout Power connections and control interfaces Type designation label Type designation key 23 23 24 24 25 26 27 Mechanical installation What this chapter contains Checking the installation site Requirements for the installation site Required tools Unpacking Checking the delivery Installing Install the drive Fasten clamping plates 29 29 29 30 31 31 32 32 34 Table of contents Planning the electrical installation What this chapter contains Implementing the AC power line connection Selecting the supply disconnecting device (disconnecting means) European union Other regions Checking the compatibility of the motor and drive Selecting the power cables General rules Alternative power cable types Motor cable shield Additional US requirements Selecting the control cables General rules Relay cable Control panel cable Routing the cables Control cable ducts Protecting the drive, input power cable, motor and motor cable in short-circuit situations and against thermal overload Protecting the drive and input power cable in short-circuit situations Protecting the motor and motor cable in short-circuit situations Protecting the drive, motor cable and input power cable against thermal overload Protecting the motor against thermal overload Using residual current devices (RCD) with the drive Implementing a bypass connection Protecting the contacts of relay outputs 35 35 35 36 36 36 36 36 37 37 38 38 38 39 39 39 40 41 41 41 41 41 42 42 42 Electrical installation What this chapter contains Checking the insulation of the assembly Drive Input power cable Motor and motor cable Checking the compatibility with IT (ungrounded) and corner-grounded TN systems Connecting the power cables Connection diagram Connection procedure Connecting the control cables I/O terminals Default I/O connection diagram Connection procedure Connecting the embedded fieldbus Connection diagram 45 45 45 45 46 46 47 47 48 49 49 52 53 54 54 Installation checklist Checking the installation 55 Table of contents Start-up and control with I/O What this chapter contains How to start up the drive How to start up the drive without a control panel How to perform a manual start-up How to perform a guided start-up How to control the drive through the I/O interface 57 57 58 59 62 65 Control panels What this chapter contains 67 About control panels 67 Applicability 67 Basic control panel 69 Features 69 Overview 70 Operation 71 Output mode 74 Reference mode 75 Parameter mode 76 Copy mode 78 Basic control panel alarm codes 79 Assistant control panel 80 Features 80 Overview 81 Operation 82 Output mode 86 Parameters mode 88 Assistants mode 91 Changed parameters mode 93 Fault logger mode 94 Time and date mode 95 Parameter backup mode 97 IO settings mode 100 10 Application macros What this chapter contains Overview of macros Summary of the I/O connections of the application macros ABB standard macro Default I/O connections 3-wire macro Default I/O connections Alternate macro Default I/O connections Motor potentiometer macro Default I/O connections Hand/Auto macro Default I/O connections 101 101 103 104 104 105 105 106 106 107 107 108 108 Table of contents PID control macro Default I/O connections PFC control macro Default I/O connections SPFC control macro Default I/O connections User macros 109 109 110 110 111 111 112 11 Program features What this chapter contains Start-up assistant Introduction Default order of the tasks List of the tasks and the relevant drive parameters Contents of the assistant displays Local control vs external control Local control External control Settings Diagnostics Block diagram: Start, stop, direction source for EXT1 Block diagram: Reference source for EXT1 Reference types and processing Settings Diagnostics Reference trimming Settings Example Programmable analog inputs Settings Diagnostics Programmable analog output Settings Diagnostics Programmable digital inputs Settings Diagnostics Programmable relay output Settings Diagnostics Frequency input Settings Diagnostics Transistor output Settings Diagnostics Actual signals Settings Diagnostics Power loss ride-through 113 113 113 114 115 117 117 118 118 118 119 119 119 120 120 120 121 121 122 122 122 123 123 123 123 124 124 125 125 125 125 125 125 126 126 126 126 126 126 127 127 Table of contents Settings DC magnetizing Settings Maintenance trigger Settings Acceleration and deceleration ramps Settings Critical speeds Settings Constant speeds Settings Custom U/f ratio Settings Diagnostics IR compensation Settings Programmable protection functions AI