1. Trang chủ
  2. » Kỹ Thuật - Công Nghệ

H 4016 8200 01 a renishaw GUI for okuma machine tools low res

2 3 0

Đang tải... (xem toàn văn)

THÔNG TIN TÀI LIỆU

Thông tin cơ bản

Định dạng
Số trang 2
Dung lượng 213,06 KB

Nội dung

Renishaw GUI for Okuma machine tools Renishaw GUI for Okuma machine tools Working in conjunction with Okuma, Renishaw has developed a range of graphical user interface (GUI) software applications Thes.

Renishaw GUI for Okuma machine tools Working in conjunction with Okuma, Renishaw has developed a range of graphical user interface (GUI) software applications These applications – Renishaw GUIs for Okuma machine tools – provide an intuitive, user-friendly programming environment that guides users through the process of generating machine code Eliminating the difficulty associated with traditional machine tool programming techniques, use of the GUI allows cycles to be produced and selected with minimal user input Key features and benefits • Provides an intuitive, easy-to-use programming interface • Simplifies calibration and operation of Renishaw machine tool probing systems • Compatible with P200M/P300M and P200/P300L controls • Integrated using Okuma’s THINC API The Renishaw GUI guides users through various probing, tool setting and machine health check cycles Feature inspection Contact tool setting Non-contact tool setting AxiSet™ Check-Up Renishaw Inc 5277 Trillium Blvd Hoffman Estates IL 60192 United States T +1 847 286 9953 F +1 847 286 9974 E usa@renishaw.com www.renishaw.com Renishaw GUI for Okuma machining centres Provides on-screen selection buttons allowing machine-resident Renishaw inspection and tool setting cycles to be called Renishaw GUI for Okuma lathes and multi-tasking machines Provides on-screen selection buttons allowing machine-resident Renishaw inspection and AxiSet Check-Up pivot point compensation cycles to be called Cycles* Type Functionality Renishaw GUI for Okuma machining centres Inspection Cycles: bore, boss, pocket, web, single surface Calibration: diameter, length Contact tool setting Cycles: manual length, automatic length, automatic length and diameter Calibration: round stylus, square stylus Non-contact tool setting Cycles: length, length and diameter Calibration: beam alignment, beam calibration Renishaw GUI for Okuma lathes and multi-tasking machines Inspection Cycles: bore, boss, pocket, web, single surface, sphere Calibration: bore, boss, pocket, web, single surface, sphere, length, slot AxiSet Check-Up Identifies poor machine alignment, geometry and pivot point errors * The relevant software packages MUST be installed and configured according to their installation documentation before using the Renishaw GUI Part numbers and compatibility Part Number Compatibility Renishaw GUI for Okuma machining centres A-4016-1063 Okuma P200 and P300M controls and API version 1.9.1.0 or later API version 1.16.0.0 is recommended (1.12.1.0 minimum) for P300M controls when running tool setting cycles: earlier versions of the API will not load tool data Renishaw GUI for Okuma lathes and multi-tasking machines A-4016-1075 Okuma P200 and P300L controls and API version 1.12.1.0 or later Please quote relevant part number(s) when ordering General requirements Ensure that the API and THINC Startup Service are installed These applications are included with all P200 and P300 controls THINC Startup Service is required to ensure that the machine’s NC is fully booted before the GUI is run If an API icon is not displayed at the bottom of the controller screen, contact your local Okuma distributor and arrange for the API to be installed For worldwide contact details, visit www.renishaw.com/contact RENISHAW HAS MADE CONSIDERABLE EFFORTS TO ENSURE THE CONTENT OF THIS DOCUMENT IS CORRECT AT THE DATE OF PUBLICATION BUT MAKES NO WARRANTIES OR REPRESENTATIONS REGARDING THE CONTENT RENISHAW EXCLUDES LIABILITY, HOWSOEVER ARISING, FOR ANY INACCURACIES IN THIS DOCUMENT © 2015 Renishaw plc All rights reserved Renishaw reserves the right to change specifications without notice RENISHAW and the probe symbol used in the RENISHAW logo are registered trade marks of Renishaw plc in the United Kingdom and other countries apply innovation and names and designations of other Renishaw products and technologies are trade marks of Renishaw plc or its subsidiaries All other brand names and product names used in this document are trade names, trade marks or registered trade marks of their respective owners *H-4016-8200-01* Issued: 03.2015 Part no H-4016-8200-01-A ... of the API will not load tool data Renishaw GUI for Okuma lathes and multi-tasking machines A - 4016 - 1075 Okuma P200 and P300L controls and API version 1.12.1.0 or later Please quote relevant part... allowing machine- resident Renishaw inspection and tool setting cycles to be called Renishaw GUI for Okuma lathes and multi-tasking machines Provides on-screen selection buttons allowing machine- resident... NO WARRANTIES OR REPRESENTATIONS REGARDING THE CONTENT RENISHAW EXCLUDES LIABILITY, HOWSOEVER ARISING, FOR ANY INACCURACIES IN THIS DOCUMENT © 2015 Renishaw plc All rights reserved Renishaw reserves

Ngày đăng: 26/10/2022, 11:09

w