CE660V INSTRUCTION MANUAL PARALLEL LATHEL CE660V INSTRUCTION MANUAL PARALLEL LATHELCE660V INSTRUCTION MANUAL PARALLEL LATHELCE660V INSTRUCTION MANUAL PARALLEL LATHELCE660V INSTRUCTION MANUAL PARALLEL LATHELCE660V INSTRUCTION MANUAL PARALLEL LATHELCE660V INSTRUCTION MANUAL PARALLEL LATHELCE660V INSTRUCTION MANUAL PARALLEL LATHELCE660V INSTRUCTION MANUAL PARALLEL LATHEL
INSTRUCTION MANUAL PARALLEL LATHE WITH INVERTER CE660Vx1500/2000/3000 INDEX IKS FOLLOW SECTION PAGE Appearance of the lathe Application and characteristics of the machine Main specifications of the machine Transportation and installation of the machine Operation system of the machine 10 Main structural property and adjustment of the machine 15 Lubrication system of the machine 24 Coolant system of the machine 27 Maintenance of the machine 27 Electric system of the machine 28 10 CAUTION • Make sure that the manual is been read before operating this machine Pay attention to the following notes • Always be sure of wearing safety shoes and goggles during operation • Wear a safety hat, and keep the sleeves and edges of the work uniform tight • Keep head and hands out of moving parts of the machine • Do not operate wearing gloves • Provide adequate light around the machine, and keep the perimeter around the machine dry, clean and in good order In addition not place anything near the machine; otherwise it becomes an obstacle during operation • Do not place tools, work pieces, or other items on the machine, especially on the moving parts • Make sure that the work piece is completely gripped, and the wrench is removed from the chuck before rotating the spindle • Stop the machine before adjusting the position of the coolant nozzles • During operating and maintenance, care should be taken so that the caution plate is not dirtied or damaged • • Disconnect power before servicing Do not move the carriage longitudinally unless it is release Advice This machine is suitable for two shift operation with each shift being hours The continuous working time should not exceed 16 hours Operation regulations should be strictly observed APPLICATION AND CHARACTERISTICS OF THE MACHINE S This machine is capable of many turning operations, such as internal and external turning, end facing and other rotary surface turning It can cut threads which may be metric or inch, module or diametral Drilling and reaming also can be carried out on it S Gap bed lathe, in addition can machine all kinds of flat parts and those in special shapes S Machining accuracy of the machine is as follows: Roundness deviation is less than 0.01 mm; cylindricity is no more than 0.02 mm over a measured length of 200 mm, surface finish not exceeds RA 1.6 y m S The lathe has many accessories for users to choose, for the details, please refer to the accessories list SPECIFICATIONS Max swing over the bed 660 mm Max swing over slide 420 mm Max swing over gap 870 mm Max cutting diameter for disc parts 480 mm Available length in gap 240 mm Max length of work piece 1500/2000/3000 mm Max cutting length 1450/1950/2950 mm Spindle nose Cam lock type D1-8 Spindle bore 0105 MM Taper and diameter of spindle bore 0113 1: 20 Steps of spindle speeds 12 Range of spindle speeds Number and range of longitudinal feeds Number and range of cross feeds Rapid longitudinal feed Rapid cross feed APERANCE OF THE MACHINE Thread cutting Metric: 22 kinds Inch: 26 kinds Module: 18 kinds D.P.: 24 kinds 36~1600 rpm 65 kinds 0.063-2.52 mm/r 63 kinds 0.027-1.07 mm/r 4.5m/min 1.9m7min 1-14 mm 28-2 TPI 0.5-7 mm 56-4 D.P Lead screw pitch Distance from spindle axis to tool supporting surface Section of tool shank Max cross travel Max swivel of top slide Max travel of top slide Max cross slide travel Max cross displacement of tail stock Taper in center sleeve bore of tail stock Max travel of tail stock sleeve Center sleeve Main motor power Main motor speed Coolant pump power Coolant pump speed Rapid feed motor power Rapid feed motor speed Overall dimensions LxWxH Net weight 12 mm (2TPI) 28 mm 25X25 mm 25x25mm 320mm ±90° 145 mm 310 mm ±15 mm Morse N°5 150 mm 75 mm 7.5 Kw 1450 rpm 60W 2800 rpm 250W 1360 rpm 3000/3500/4500 mm x 1100 mm x 1450 mm 3200/3400/3900 kg TRASNPORTATION AND INSTALLATION OF THE MACHINE A) When machines are craned, be sure to crane one package at a time so as to avoid shocking B) When rollers are used for transportation, their diameter should be 70 to 80 mm, and the ground slant should be less than 15° C) Be sure to avoid collision of the operation levers and the surface of the machine D) To crane the machine, use a steel wire rope to tie on the ribs of the bed The contact surface should be lined with cotton yarn or wood pieces To keep the balance of the machine, move the tail stock and apron to the right end and lock them tightly to the bed so as to prevent them from sliding (See Fig 2) E) The machine should be mounted on a solid foundation where no vibration will be caused when it is working Put a leveling pad near of each foot hole, and fasten the machine with foot screws The dimensions of the foundation are shown in Fig APPLICATION AND CHARACTERISTICS OF THE MACHINE When the machine is to be mounted on a concrete foundation, it is necessary to prepare considerably deep foot screw holes beforehand If the foundation is a concrete floor, the holes must be through For the installation of the machine, a level gage must be used to set the longitudinal and cross levelness of the machine Fix the foot screws with concrete After the cement has become dry and solid, tighten the foot screw nuts evenly to avoid distortion of the machine which will affect machine accuracy After re checking the machine levelness, pour cement down under the bed stands to fix them R A —- - - J H -4 S5 SIZE I L v= - I M CO CD 620 1500 2060 2995 2000 2560 3495 ^ 8-M24X2 < APERANCE OF THE MACHINE 620 1721.5 184 3.5 4500 (for 3000mm lathe) H - % , % CM < 6-M24X2 _ 24 4" CM -fe I -L S' i i