Tài liệu Handbook of Mechanical Engineering Calculations P25 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P25 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P25 pdf

... (www.digitalengineeringlibrary.com) Copyright © 2006 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING ... outside diameter of 2 7 ⁄ 8 in (7.07 cm), the same as the OD of the raised flange, per ASA-B16.5, and an ID of 1.5 in (3.8 cm). The seating stress is computed from Dow...

Ngày tải lên: 23/01/2014, 05:20

80 327 0
Tài liệu Handbook of Mechanical Engineering Calculations P3 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P3 pdf

... combustion and increases the weight of the products of combustion per pound (kilogram) of coal burned. Therefore, the weight of the products of combustion is the sum of the weight of the combustion products ... /18)(0.013) ϭ 0.0209, say 0.021 mol of water per mol of air. The product of this and the moles of air gives the total moles of Downloaded from Digital Engineer...

Ngày tải lên: 17/12/2013, 11:15

24 745 0
Tài liệu Handbook of Mechanical Engineering Calculations P5 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P5 pdf

... reserved. Any use is subject to the Terms of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS 5.10 POWER GENERATION traction throttle flow is (SR)(kW output) ϭ 9.25(10,000) ϭ 92,500 ... output of the existing system is increased, as noted, because of increasing flow to the steam turbine’s condenser. This increased output offsets the cost of...

Ngày tải lên: 17/12/2013, 11:15

16 617 1
Tài liệu Handbook of Mechanical Engineering Calculations P6 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P6 pdf

... average heat of vaporization of 1000 Btu / lb (2330 kJ / kg) of steam, this exhaust gas flow could generate 8,880,000 /1000 ϭ 8880 lb/h (4032 kg/h) of steam. If oil with a heating value of 145,000 ... types of fuels and the internal-combustion engines using them. Note that where the cost of the fuel is high, the cost of the engine is low; where the cost of the fuel is low, th...

Ngày tải lên: 17/12/2013, 11:15

44 735 0
Tài liệu Handbook of Mechanical Engineering Calculations P9 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P9 pdf

... (www.digitalengineeringlibrary.com) Copyright © 2006 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING ... (339.6 m 3 /min) of air at a pressure of 14 lb/in 2 (abs) (96.46 kPa) and a temperature of 60 Њ F (15.6 Њ C). Downloaded from Digital Engineering Library @ McGraw-H...

Ngày tải lên: 17/12/2013, 11:15

44 648 1
Tài liệu Handbook of Mechanical Engineering Calculations P12 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P12 pdf

... the work of Norman R. Sparks, Professor and Head, Depart- ment of Mechanical Engineering, The Pennsylvania State University, and Charles C. DiLio, Associate Professor of Mechanical Engineering, ... the work of Norman R. Sparks, Professor and Head, Depart- ment of Mechanical Engineering, The Pennsylvania State University, and Charles C. DiLio, Associate Professor of Mecha...

Ngày tải lên: 17/12/2013, 11:15

80 512 0
Tài liệu Handbook of Mechanical Engineering Calculations P23 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P23 pdf

... rights reserved. Any use is subject to the Terms of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS 23.20 DESIGN ENGINEERING The above procedure assumes the spring ... total angle of twist of 0.20 rad? The bar is made of 302 stainless steel, which has a proportional limit in tension of 35,000 lb/in 2 (241.3 ϫ 10 6 Pa), and G ϭ torsio...

Ngày tải lên: 23/01/2014, 05:20

46 520 1
Tài liệu Handbook of Mechanical Engineering Calculations P4 pptx

Tài liệu Handbook of Mechanical Engineering Calculations P4 pptx

... M ƒ ϭ lb of moisture per lb fuel burned; M a ϭ lb of moisture per lb of dry air to furnace; C b ϭ lb of carbon burned per lb of fuel burned ϭ C ϭ RC r ; C r ϭ lb of combustible per lb of refuse; ... lb of fuel ϭ W c (14,150), where W c ϭ lb of unconsumed carbon in refuse per lb of fuel fired. With an ash and refuse of 9.42 percent of the dry coal and combustible in the...

Ngày tải lên: 17/12/2013, 11:15

80 635 0
Tài liệu Handbook of Mechanical Engineering Calculations P7 docx

Tài liệu Handbook of Mechanical Engineering Calculations P7 docx

... Terms of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS 7.46 PLANT AND FACILITIES ENGINEERING 0.392 ϩ 0.784 ϭ 138.226 ft (42.1 m), say 140 ft (42.7 m) of water. ... is 80 percent of bep capacity. For a specific speed of 1090, as before, the percentages of bep head and efficiency are shown in Figs. 36 and 37: 79.5 percent of bep head...

Ngày tải lên: 17/12/2013, 11:15

86 917 14
Tài liệu Handbook of Mechanical Engineering Calculations P8 doc

Tài liệu Handbook of Mechanical Engineering Calculations P8 doc

... subject to the Terms of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS 8.10 PLANT AND FACILITIES ENGINEERING residential, industrial), and other plants. Both ... cost of each type of pipe uses the capital-recovery equation, A ϭ (P Ϫ L)(CR) ϩ Li 1 ϩ c, where A ϭ annual cost, $; P ϭ initial cost of each type of piping, $; L ϭ salvage...

Ngày tải lên: 17/12/2013, 11:15

136 561 0
w