Tài liệu Configuring IBGP and EBGP Sessions pdf

... lab, you configure both IBGP and EBGP. In order for IBGP peers to correctly exchange routing information, you must also use the next-hop-self and aggregate- address commands. Scenario The ... 5: Advanced Routing v2.0 - Lab 8.8.2 Copyright  2001, Cisco Systems, Inc. 8.8.2 Configuring IBGP and EBGP Sessions Lo0 10.1.1.1/32 Fa0/0 172.16.1.1/24S0/0 192.168.1.6/30 Fa0/...

Ngày tải lên: 18/01/2014, 05:20

... Services and Applications Once the Computer Management window displays on screen, click the plus (+) symbol to the left of “Services and Applications” and select Services from the expanded tree. ... server, a user can run programs and issue commands, provided those commands do not require the GUI. When finished with the Telnet session, type exit at the command prompt. Exit will en...

Ngày tải lên: 11/12/2013, 15:15

... consulting and computer/web based testing. They market a cognitive ability /personality system (ASSESS) which can be used for selection or development. Cognitive tests are Watson-Glaser and Raven's ... in-house. Two-thirds of BHA's employees are designers and programmers. BHA's strategy is to grow by adding to its product line- and several are close to completion. Ex...

Ngày tải lên: 12/12/2013, 00:15

Ngày tải lên: 17/12/2013, 14:15

... 1.4.2 Introductory Lab 2: Capturing HyperTerminal and Telnet Sessions Objective This activity describes how to capture HyperTerminal and Telnet sessions. Note: Be sure to master these techniques. ... HyperTerminal capture is CAPTURE.TXT, and the default location of this file is C:\Program Files\Accessories\HyperTerminal. Note: When you are using Telnet, the command to begin...

Ngày tải lên: 21/12/2013, 19:15

... 1.4.2 Introductory Lab 2: Capturing HyperTerminal and Telnet Sessions Objective This activity describes how to capture HyperTerminal and Telnet sessions. Note: Be sure to master these techniques. ... HyperTerminal capture is CAPTURE.TXT, and the default location of this file is C:\Program Files\Accessories\HyperTerminal. Note: When you are using Telnet, the command to begin...

Ngày tải lên: 21/12/2013, 19:15

... using. Note: Host A and Host B are not required to complete this lab. On all three routers, configure RIPv1 and enable updates on all active interfaces with this network command: SanJose1(config)#router ... Jose1 San Jose2 Objective In this lab, you configure VLSM and test its functionality with two different routing protocols, RIPv1 and RIPv2. Finally, you use IP unnumber...

Ngày tải lên: 21/12/2013, 19:15

... graphical interface is used to issue commands to the control circuitry. The provided IP handles all requests and performs data transfers between the computer and the DE2 board. DE2 User Manual ... 8 power and ground lines, are brought out to two 40-pin expansion connectors • 40-pin header is designed to accept a standard 40-pin ribbon cable used for IDE hard drives • Diode and...

Ngày tải lên: 22/12/2013, 21:17

... $35,968 Costs and expenses: Cost of sales 23,045 20,255 23,438 Sales and marketing 7,476 7,261 6,840 Research and development 5,043 5,105 3,323 General and administrative 1,951 1,788 1,722 Total cost and ... and accounts re- ceivable. • Inventories: Kmart is a retailer of consumer products and maintains inventories of merchandise in regional ware- houses and retail stores. HBO...

Ngày tải lên: 17/01/2014, 04:20

... Performance Logs and Alerts Through the Performance Logs and Alerts utility, you can configure logs of performance-related data (called counter logs and trace logs) and generate alerts ... “Installing Non-Plug- and- Play Hardware,” “Updating Drivers,” “Managing Disk Drives,” and “Troubleshooting Devices” sections later in this chapter. Local Users and Groups The Local...

Ngày tải lên: 17/01/2014, 07:20