Tài liệu Configuring Legacy DDR docx

... Lab 4.3.2 Configuring Legacy DDR Objective • Configure an ISDN router to make a Legacy dial-on-demand routing (DDR) call to another ISDN capable router. • When the DDR connection is ... static routes for DDR a. Use static and default routes instead of dynamic routing, in order to reduce the cost of the dialup connection. To configure a static route, the network addres...

Ngày tải lên: 21/12/2013, 19:15

... Lab 4.3.2 Configuring Legacy DDR Objective • Configure an ISDN router to make a Legacy dial-on-demand routing (DDR) call to another ISDN capable router. • When the DDR connection is ... static routes for DDR a. Use static and default routes instead of dynamic routing, in order to reduce the cost of the dialup connection. To configure a static route, the network addres...

Ngày tải lên: 18/01/2014, 04:20

... < Day Day Up > Configuring Component Properties As you're well aware by now, most graphical elements used

Ngày tải lên: 14/12/2013, 22:15

... while relying on legacy components for some functions. For example, a large organization may choose to implement CallManager as a replacement for its legacy PBXs while continuing to use a legacy voice ... telephony networks with legacy PBX systems. In the sections to follow, we will describe some of the standard protocols that can be used in an AVVID environment for integrating with...

Ngày tải lên: 17/01/2014, 09:20

... commands, source the ping from Auckland’s FastEthernet 0/0 address, 192.168.248.1: Auckland#ping Protocol [ip]: ip Target IP address: 192.168.5.1 Repeat count [5]: 5 Datagram size [100]: ... - 7 Semester 5: Advanced Routing v2.0 - Lab 7.5.1 Copyright  2001, Cisco Systems, Inc. 7.5.1 Configuring Distribute Lists and Passive Interfaces RIPv2 Full T1: 1.544 Mbps 19.2 Kbps Singapore...

Ngày tải lên: 21/12/2013, 19:15

... CCNA 4: WAN Technologies v 3.0 - Lab 4.2.1 Copyright  2003, Cisco Systems, Inc. Lab 4.2.1 Configuring ISDN BRI (U-Interface) Objective • Configure an ISDN router to make a successful ... terminal • The enable passwords If there is a problem completing this, refer to the Network Address Translation (NAT) configuration lab. Step 2 Verifying the ISDN BRI switch type a. Not ......

Ngày tải lên: 21/12/2013, 19:15

... view. ■ Management of client addresses Solutions need to be able to assign the external client an internal address so that the network will treat it as a local node. The client’s actual network address (supplied ... reason you wish to define the range of IP addresses that the DHCP server will use to assign addresses to remote users, choose the “From a specified range of addresses” radio button...

Ngày tải lên: 17/01/2014, 09:20

... enabled, but has an incorrect IP address: 192.168.1.254. Fix the IP address: configure terminal, interface fa0/0, ip address 192.168.1.1 255.255.255.0, end. Verify the IP address: show interface fa0/0. ... executing: winipcfg. Make sure the IP addressing information is correct: IP address of 192.168.1.10, subnet mask of 255.255.255.0, and default gateway address of 192.168.1.1. Click on the C...

Ngày tải lên: 18/01/2014, 04:20

... with the appropriate addresses. The company requires that at least 25 host addresses be available on each LAN, but it also demands that you conserve the maximum number of addresses for future ... of VLSM to further conserve addresses. Scenario When International Travel Agency was much smaller, it wanted to configure its network using a single Class C address: 192.168.1.0 (shown in ......

Ngày tải lên: 18/01/2014, 05:20

... registered IP addresses.This saves your organization money—but, as they say in the commercials, that’s not all. Because all the internal IP addresses get “translated” to a single public address, which ... SecureNAT do? A: NAT (Network Address Translation) is a means of providing Internet access to computers on an internal network using only one external (registered) public IP address.The NAT...

Ngày tải lên: 24/01/2014, 10:20