Tài liệu Nghệ thuật xếp hình Nhật Bản: sunrise 2 ppt

... blunders and mistakes. This is a translation of a German article that originally appeared on no. 22 of der falter , the magazine of Origami Deutschland. I dedicate this translation to Jan Polish, ... opposite slot. Long finger- nails and/or tweezers can be helpful for the last bit. 2 The basic unit Length of the strip = 42  width I will now describe how to make a basic unit with three cub...

Ngày tải lên: 10/12/2013, 12:15

... 22 .Swing over. 23 .Petal up. 24 .Swing up. 27 .Valley outwards .26 .Swing down .25 .Sink triangularly. 28 .Precrease flap halfway. 29 .Valley along precrease. 30.Valley ... make symetrical. 8.Squash.7.Asymmetrical squash. Complex An 18" square makes a model 6" high 22 -33 1 /2 36-37,39-40 3-5 34.Repeat steps 22 -33 on the other side. 35. Valley. Rotate model. 36.Squash. 39...

Ngày tải lên: 10/12/2013, 12:15

Ngày tải lên: 10/12/2013, 12:15

... half a segment from the tall stack 8 9 Make the step 2 segments tall 10 Add another step 11 Make this step 2 segments tall 12 Make another 2 segment step as in steps 10 & 11 ... Eiffel tower © Robin Glynn - July 1998 1 2 3 Crease into thirds Crease into 3rds again to make 9ths Crease into 3rds once more to make 27 ths 4 5 Form a small box in the centre of the paper Repeat

Ngày tải lên: 21/12/2013, 03:15

... this) 8 This is the half way stage 9 10 11 12 13 Repeat steps 3-8 on this side 14 15 16 Fold the point up inside the model (much harder than step 7!) 17 18 19 See step 20 20 Swivel the point to the left Line ... 1 Black Belt in Origami Diagrammed by R.Glynn © February 1999 2 3 Preliminary fold 4 5 6 Pull out the loose paper (it helps if you unfold to step 4 first) 7 Fold

Ngày tải lên: 21/12/2013, 03:15

Ngày tải lên: 17/01/2014, 04:20

...

Ngày tải lên: 17/01/2014, 04:20

... left, repeating behind. Reverse fold on the right and reverse fold again. Steps 22 to 24 are close ups of the head. 22 . 23 . 24 . Outside reverse at the top while crimp folding below like this. Make ... 14. 15. 16. 17. 18. 19. 20 . 21 . 21 . Fold over and over. Repeat Steps 12 to 15 on the other side. Outside reverse fold on the left and then the

Ngày tải lên: 17/01/2014, 04:20

... right. 2 22. Flip 1 flap over, and pull the next flap towards the left. Model won’t lie flat. 22 -23 24 . Repeat 22 -23 on left. Turn over. 25 . Fold top point to center. Turn back over. 26 . Valley ... downwards. Don’t crease. 20 . Reverse-fold, flipping over the rectangular single-ply. Press flat and sharpen all creases. 16 -20 21 . Repeat 16 -20 on left. Turn over. not to corne...

Ngày tải lên: 17/01/2014, 04:20

... fold the body to form the rear end of the dog. (Here is a hint, do it one side at a time.) 21 22 23 24 25 5 Valley fold the sides from the top to the center of the model. 6 Reach under to the hidden ... the top flap up as if for the bird base. 1 /2 1 /2 1 /2 1 /2 9 Mark the spot half way between the corner of the bird base and the crease formed in step 2. 10 Valley fold the top la...

Ngày tải lên: 17/01/2014, 04:20